Some clients seem to rely upon the reception of BlockAckReqs to flush
their rx reorder buffer. In order to fix aggregation for these clients
carl9170 should set IEEE80211_TX_STAT_AMPDU_NO_BACK to generate a
BlockAckReq if the transmission of an AMPDU subframe fails.
This fixes aggregation problems with Intel 5100 Windows STAs (and maybe
others as well).
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When the chip is still asleep when ath9k_start is called,
ath9k_hw_configpcipowersave can trigger a data bus error.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
commit 86271e460a introduced a
regression that caused mac80211 queues in stopped state.
ath_drain_all_txq is called in driver flush which would reset
the stopped flag and the mac80211 queues were never started
after that. iperf traffic is completely stalled due to this issue.
Restart the mac80211 queues in driver flush only if the txqs were
drained.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent tx status optimization in mac80211, we bail out as
and and when invalid rate index is found. So the behavior of resetting
rate idx to -1 and count to 0 has changed for the rate indexes that
were not part of the driver's retry series.
This has resulted in ath9k using incorrect rate table index which
caused the system to panic. Ideally ath9k need to loop only for the
indexes that were part of the retry series and so simply use hw->max_rates
as the loop counter.
Pasted the stack trace of the panic issue for reference.
[ 754.093192] BUG: unable to handle kernel paging request at ffff88046a9025b0
[ 754.093256] IP: [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
[ 754.094888] Call Trace:
[ 754.094903] <IRQ>
[ 754.094928] [<ffffffffa051f883>] ieee80211_tx_status+0x203/0x9e0 [mac80211]
[ 754.094975] [<ffffffffa053e305>] ? __ieee80211_wake_queue+0x125/0x140 [mac80211]
[ 754.095017] [<ffffffffa02e66c9>] ath_tx_complete_buf+0x1b9/0x370 [ath9k]
[ 754.095054] [<ffffffffa02e6fcf>] ath_tx_complete_aggr+0x51f/0xb50 [ath9k]
[ 754.095098] [<ffffffffa05382a3>] ? ieee80211_prepare_and_rx_handle+0x173/0xab0 [mac80211]
[ 754.095148] [<ffffffff81350e62>] ? _raw_spin_unlock_irqrestore+0x32/0x40
[ 754.095186] [<ffffffffa02e9735>] ath_tx_tasklet+0x365/0x4b0 [ath9k]
[ 754.095224] [<ffffffff8107a2a2>] ? clockevents_program_event+0x62/0xa0
[ 754.095261] [<ffffffffa02e2628>] ath9k_tasklet+0x168/0x1c0 [ath9k]
[ 754.095298] [<ffffffff8105599b>] tasklet_action+0x6b/0xe0
[ 754.095331] [<ffffffff81056278>] __do_softirq+0x98/0x120
[ 754.095361] [<ffffffff8100cd5c>] call_softirq+0x1c/0x30
[ 754.095393] [<ffffffff8100efb5>] do_softirq+0x65/0xa0
[ 754.095423] [<ffffffff810563fd>] irq_exit+0x8d/0x90
[ 754.095453] [<ffffffff8100ebc1>] do_IRQ+0x61/0xe0
[ 754.095482] [<ffffffff81351413>] ret_from_intr+0x0/0x15
[ 754.095513] <EOI>
[ 754.095531] [<ffffffff81014375>] ? native_sched_clock+0x15/0x70
[ 754.096475] [<ffffffffa02bcfa6>] ? acpi_idle_enter_bm+0x24d/0x285 [processor]
[ 754.096475] [<ffffffffa02bcf9f>] ? acpi_idle_enter_bm+0x246/0x285 [processor]
[ 754.096475] [<ffffffff8127fab2>] cpuidle_idle_call+0x82/0x100
[ 754.096475] [<ffffffff8100a236>] cpu_idle+0xa6/0xf0
[ 754.096475] [<ffffffff81339bc1>] rest_init+0x91/0xa0
[ 754.096475] [<ffffffff814efccd>] start_kernel+0x3fd/0x408
[ 754.096475] [<ffffffff814ef347>] x86_64_start_reservations+0x132/0x136
[ 754.096475] [<ffffffff814ef451>] x86_64_start_kernel+0x106/0x115
[ 754.096475] RIP [<ffffffffa02eac49>] ath_tx_status+0x209/0x2f0 [ath9k]
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some clients seems to keep track of their reorder window even after an
aggregation session has been disabled. This causes issues if there are
still retried but not completed frames pending for the TID.
To ensure that rx does not stall in such situations, set sendbar to 1
for any frame purged from the TID queue on teardown.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k calls ath9k_hw_stoptxdma every time it sends a beacon, however there
is not much point in doing that if the previous beacon and mcast traffic
went out properly. On AR9380, calling that function too often can result
in an increase of stuck beacons due to differences in the handling of the
queue enable/disable functionality.
With this patch, the queue will only be explicitly stopped if the previous
data frames were not sent successfully. With the beacon code being the
only remaining user of ath9k_hw_stoptxdma, this function can be simplified
in order to remove the now pointless attempts at waiting for transmission
completion, which would never happen at this point due to the different
method of tx scheduling of the beacon queue.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch simplifies the flush op and reuses ath_drain_all_txq for
flushing out pending frames if necessary. It also uses a global timeout
of 200ms instead of the per-queue 60ms timeout.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some situations, stopping Tx DMA frequently fails, leading to messages
like this:
ath: Failed to stop TX DMA in 100 msec after killing last frame
ath: Failed to stop TX DMA!
This patch uses a few MAC features to abort DMA globally instead of iterating
over all hardware queues and attempting to stop them individually.
Not only is that faster and works with a shorter timeout, it also makes the
process much more reliable.
With this change, I can no longer trigger these messages on AR9380,
and on AR9280 they become much more rare.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increasing the wait count makes the nf load pass in
most of the cases.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Increase the delay to make sure the initialization of pll
passes.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Set some GPIO pins to Pull-down mode to save power.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The hardware rx filter flag triggered by FIF_PROMISC_IN_BSS is overly broad
and covers even frames with PHY errors. When this flag is enabled, this message
shows up frequently during scanning or hardware resets:
ath: Could not stop RX, we could be confusing the DMA engine when we start RX up
Since promiscuous mode is usually not particularly useful, yet enabled by
default by bridging (either used normally in 4-addr mode, or with hacks
for various virtualization software), we should sacrifice it for better
reliability during normal operation.
This patch leaves it enabled if there are active monitor mode interfaces, since
it's very useful for debugging.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It seems ath5k has issues receiving broadcast packets (ARPs) when
using multiple STA interfaces associated with multiple APs.
This patch ensures the NIC is always in PROMISC mode if there
are more than 1 stations associated.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No use printing addresses of pointers, just print the
pointers themselves.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
/<debugfs_root>/ieee80211/phyX/ath9k/regdump is the interface
to dump the registers.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AID and BSSID should be set in the HW only for the
first station interface or adhoc interface. Also, cancel
the ANI timer in stop() for multi-STA scenario. And finally
configure the HW beacon timers only for the first station
interface.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9485 doesn't use the default GPIO pin for LED and GPIO 6 is actually
used for this.
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The stream length/tag fields have to be in little endian
format. Fixing this makes the driver work on big-endian
platforms.
Cc: stable@kernel.org
Tested-by: raghunathan.kailasanathan@wipro.com
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize txq to avoid this warning:
drivers/net/wireless/ath/ath9k/main.c: In function ‘ath9k_flush’:
drivers/net/wireless/ath/ath9k/main.c:2138: warning: ‘txq’ may be used uninitialized in this function
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
pll_work should be cancelled on full_sleep or it may cause
redundant chip reset.
Signed-off-by: Vivek Natarajan <vnatarajan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).
Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.
Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
"AirLive X.USB now works perfectly under a Linux
environment!"
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit 4df3071ebd "ath9k_hw: optimize
interrupt mask changes", changed ath9k_hw_set_interrupts function to
enable interrupts regardless of function argument, what could possibly
be wrong. Correct that behaviour and check "ints" arguments before
enabling interrupts, also disable interrupts if ints do not have
ATH9K_INT_GLOBAL flag set.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The flag isn't very descriptive -- the intention
is that the driver provides a TSF timestamp at
the beginning of the MPDU -- make that clearer
by renaming the flag to RX_FLAG_MACTIME_MPDU.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hif_usb_alloc_urbs() takes care of freeing
all the allocated URBs for the various endpoints when
an error occurs. Calling ath9k_hif_usb_dealloc_urbs() would
cause a panic since the URBs have already been freed.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add ATH9K_RX_FILTER_UNCOMP_BA_BAR and ATH9K_RX_FILTER_PSPOLL
when mac80211 requires it.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There is no need to set the BSSID mask or opmode when
initializing RX, they would be set correctly in the HW reset
routine.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The target beacon transmission time has to be synced with the HW
TSF when configuring beacon timers in Adhoc mode. Failing to do this
would cause erroneous beacon transmission, for example, on completion
of a scan run to check for IBSS merges.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Handle multi-interface situations by checking if
AP interfaces are already present.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The time granularity for the ANI task is different for AP and
station mode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required for allowing only one IBSS interface to be
configured.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is required when issuing commands to the firmware.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
