This minimises the chance of any external capacitors that are fitted
being discharged into headphones as they insert.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current ak4642 driver had wrong dapm settings for headphone L/R.
If you select headphone L, and select R after that,
headphone L setting was removed by R settings.
This patch fixes it up.
It provides just "Headphone Enable" to user side
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Replace the printk(KERN_ERR* instances with dev_err in the driver.
While we are here clean up some of the debug messages as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8775 is register compatible with the WM8776 so can be supported with
the same driver though it is an ADC only part. Add the device ID to the
WM8776 driver, further updates will be added in the future.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_PCM is already selected by SND_SOC, there is no need for
SND_IMX_SOC and SND_MXS_SOC to select it again.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch supports DMAEngine to FSI driver.
It supports only Tx case at this point.
If platform/cpu doesn't support DMAEngine, FSI driver will
use PIO transfer.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPQDoTAAoJEHm+PkMAQRiGMpYH/ibfyIFBrKMD1v/s9oNvp8rS
c7J7E7mHZOylCHrpIS3lX3ZbOfOe33Ln0Z59f1/TcV4CMMz0NrKYcTC8erj/H/DA
8DRYegiczWKqiXRgktwaZXkJcwXYdOOL1WQYxuzzbZcwRrNBY2QpH7Zu8Bj+TPAy
d4fvJHWdlh4sbWVdQmLRbp04UB9J/Z5/uWmSNvVQjLLdRlD+mEBbt7JjiNY6sUVC
2sJoAs9F3UlHu7VaN+JIhMOGZ3GqOpHGBxN/aWxJ/7GsXdXuAfCrxoPxaAe4xzOa
HndN5ZDyg02Vy5uDeUzj+HJPW3M8L4Q0nwxAYb3ZnQ5tbpu1Q2cHfIBealomWCQ=
=R91X
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc4' into for-3.4 in order to resolve the conflict
resolved below within the FSI driver and allow the application of the
dmaeengine conversion that depends on this resolution.
Linux 3.3-rc4
Conflicts:
sound/soc/sh/fsi.c
This fixes below build warning:
WARNING: vmlinux.o(.text+0x1e632c): Section mismatch in reference from the function pxa2xx_ac97_probe() to the function .devinit.text:pxa2xx_ac97_hw_probe()
The function pxa2xx_ac97_probe() references
the function __devinit pxa2xx_ac97_hw_probe().
This is often because pxa2xx_ac97_probe lacks a __devinit
annotation or the annotation of pxa2xx_ac97_hw_probe is wrong.
Also rename pxa_ac97_dai to pxa_ac97_dai_driver to fix below build warning:
LD sound/soc/pxa/built-in.o
WARNING: sound/soc/pxa/built-in.o(.data+0x18c): Section mismatch in reference from the variable pxa_ac97_dai to the function .devinit.text:pxa2xx_ac97_probe()
The variable pxa_ac97_dai references
the function __devinit pxa2xx_ac97_probe()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*driver, *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Showing the returned values on error messages is useful information.
While at it, use pr_err/pr_warn whenever possible.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
While it matches the current code only bringing the device out of reset
isn't actually doing what the function says so make sure we set the GPIO
high before we pull it low.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This means we don't need to walk through every single widget in the system
for each stream event which is a bit less silly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do smarter things with DAI links create DAPM
widgets which directly represent the DAIs in the DAPM graph. These are
automatically created from the DAIs as we probe the card with references
held in both directions between the widget and the DAI.
The widgets are not made available for direct instantiation by drivers,
they are created automatically from the DAIs. Drivers should be updated
to create stream routes using DAPM maps rather than by annotating AIF
and DAC widgets with streams.
In order to ease transition to this model from existing drivers we
automatically create DAPM routes between the DAI widgets and the existing
stream widgets which are started and stopped by the DAI widgets, though
the old stream handling mechanism is still in place. This also has the
nice effect of removing non-DAPM devices as any device with a DAI
acquires a widget automatically which will allow future simplifications
to the core DAPM logic.
The intention is that in future the AIF and DAI widgets will gain the
ability to interact such that we are able to manage activity on
individual channels independantly rather than powering up and down the
entire AIF as we do currently.
Currently we only generate these for CODECs, mostly as I have no systems
with non-CODEC DAPM to integrate with. It should be a simple matter of
programming to add the additional hookup for these.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Neater and avoids warnings when used in other places where const strings
are desired.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
In order to allow us to do something smarter than iterate through widgets
doing strcmp() to work out what to power up for stream events change the
interface used to generate them to be based on the combination of a DAI
and a stream direction rather than just a simple string identifying the
stream.
At some point we'll probably want a set of channels too.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Let the caller fiddle with the widget after we're done in order to
facilitate further refactoring.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Everything now uses snd_soc_dapm_new_controls() instead so we don't need
to make it part of the external API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
This fixes below build warning:
CC sound/soc/pxa/spitz.o
sound/soc/pxa/spitz.c: In function 'spitz_startup':
sound/soc/pxa/spitz.c:116: warning: passing argument 1 of 'spitz_ext_control' from incompatible pointer type
sound/soc/pxa/spitz.c:47: note: expected 'struct snd_soc_card *' but argument is of type 'struct snd_soc_codec *'
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows userspace control of final power off, allowing policy decisions
for register configuration retention.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Only enable and disable the FLL when explicitly told to, supporting some
additional use cases and making the driver behaviour more standard.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Make sure we update for any changes in cases where we reconfigure while
live (eg, for analogue bypass).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Machine kcontrols now use card instead of codec for thier "chip".
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Show the id we read when the id mismatch is detected.
This is useful for debugging.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow platform widgets to be visible in debugfs like codec widgets.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since the addition of the non-CODEC control adds card controls like the
DAPM pin switch have been broken as they are expecting the private data
for the control to be the CODEC but it's now the card. Fix that for the
pin switches, an audit of other drivers is required.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Update the codec debugfs initialisation to use dev_warn() instead of
printk(KERN_WARNING).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Currently when DAPM widgets are power sequenced the stream_event()
completion callback is only called for the stream_event originator
DAPM context. Other components in the card may also be interested so
make sure they are also notified of any widget power events.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's useful to export the DAPM reset as a static function for future use
by other DAPM functions. e.g. The dynamic PCM query widgets resets the DAPM
graph before working out active paths.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The main role of the WM9081 is as a class D speaker amplifier so there
is no concern about pops. There are also very few registers and a fast
power up time so we can happily mark the driver as idle_bias_off.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
ALC5632 codec supports digital microphone. This patch adds DAPM widget.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Raise the ramp time to 50ms to cover corner cases, use the startup bias
generator, explicitly reset the ramp circuit when complete and reorder
things all of which should improve performance somewhat for systems that
are sensitive to noise from VMID.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The enable of the single ended line outputs on wm_hubs devices performs
better if the output is enabled prior to starting VMID. Since inactive
outputs are held at VMID anyway there is little cost to doing this for
unused outputs. Add callbacks into wm_hubs and keep track of which outputs
are really active so we can disable them once we're active.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
According to the mixer path diagram input sources' attenuators logically
belong to the playback path and DMIC boost only affects capture.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This brings the TLVs in sync with the documentation and allows to properly
manipulate mic boost controls with alsamixer.
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch should fix output through speakers using HP mixer.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix I2S digital interface power for recording.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add DMIC switches and controls to ALC5632 codec.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
There is no Phone Mix<->Mono Mix route in datasheet.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Rename capture switches to common scheme XXX2REC.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Remove extra zero from volume step in DECLARE_TLV_DB_SCALE macro.
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The various devm_ functions allocate memory that is released when a driver
detaches. This patch uses these functions for data that is allocated in
the probe function of a platform device and is only freed in the remove
function.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build error which is introduced by
commit 022658 "ASoC: core: Add support for DAI and machine kcontrols".
CC [M] sound/soc/omap/n810.o
sound/soc/omap/n810.c: In function 'n810_set_input':
sound/soc/omap/n810.c:194: error: 'codec' undeclared (first use in this function)
sound/soc/omap/n810.c:194: error: (Each undeclared identifier is reported only once
sound/soc/omap/n810.c:194: error: for each function it appears in.)
sound/soc/omap/n810.c:188: warning: unused variable 'card'
make[3]: *** [sound/soc/omap/n810.o] Error 1
make[2]: *** [sound/soc/omap] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Correct spelling "memroy" to "memory" in
sound/soc/codecs/twl4030.c
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. the number of the half-beast?
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPMzv8AAoJEHm+PkMAQRiGgeYIAJxxGCxSMLRIiPaGRmQbWifs
eE3z6AUWitGfYvhmYdWVz+C/aa4pPCVWr3bAFxUQhu+ESmiFIiqiefvlTRf5f84e
pcoJFobkFfhtK4gLvUr75WxXDFq/1HhKqW1OLzIW4gQsnhMdjGJ3lLK6ZoRYH8h4
cGoN3DRII9mVLFcB2sgbeRvbQBA/O4n0aOQ2ryZkCcPQQMIKhR/rUEEV2pe/ovHE
rumQgI3PVey816P4e5YnOvrEAllFZlaZ/F0ClJgNdfeQCVTZx9KNRbiNxHi6fcC5
6Zgg7e5EvQTAy7QqQZ0hmS4k4CFmnswX3Nm+ZabRNqBdLSjPEDD9hk1o1dodYCg=
=BBLC
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc3' as we've got several bugfixes in there which are
colliding annoyingly with development.
Linux 3.3-rc3
.. the number of the half-beast?
Conflicts:
sound/soc/codecs/wm5100.c
sound/soc/codecs/wm8994.c
current fsi_pointer() calculation was not correct for FSI driver.
This patch fix it up.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It's set unconditionally.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
This is usually not a use case dependant flag anyway.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Since we've already got logic to special case immediate teardown of the
stream we may as well use it if the pmdown_time has been set to zero by
the application layer instead of scheduling a work item with zero delay.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The VMID ramp rate is supposed to be 0x3, not 11b. Fix that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Make sure we generate enough BCLKs for I2S style modes by always having
a minimum of two channels worth of clocks for the BCLK.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
No practical impact but now we have the control type we may as well use
it for the slightly nicer sequencing.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we're not implementing GPIO or microphone detection support
there's no users for the read() function any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Make the mechanism used for WM8994 more like that for WM1811 and WM8958:
provide the logic to distinguish between headphone and headset and hard
code the reporting of sensible SND_JACK values. Should integration with
other detection mechanisms be required we can add appropriate callbacks
(though some integrations should be able to use the subsystem ones).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise we might get an error if the GPIO is configured as an input
since that makes the register volatile and a suspended device can't be
read from.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the default state that the runtime PM infrastructure expects so
instead just kick the runtime PM core to suspend us if we're not doing
anything (as is default).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix build breakage by using the correct API call to add kcontrols.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Looks like nobody is or will be using this code.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix some spelling mistakes in the header and remove the todo items. Most
todo items are now available as kcontrol options now anyway.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow for the operation of custom mixer and mux DAPM widgets that can call
snd_soc_dapm_mixer_update_power() and snd_soc_dapm_mux_update_power() directly
after updating their status. This is useful with complex DAPM Mixer operations
where we need to do additional work in addition to setting a few mixer register
bits.
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In cases where we should enter STANDBY DAPM will power us up, otherwise
there is no need to power up and we can remain in OFF.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8994 has a different accessory detect architecture, call its setup
function too. We ignore the errors and the driver will check for chip type
so it's safe to call the setup functions for both architectures.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can enable VMID independently of the bias in some use cases so we need
to ensure that the core device is powered up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Currently ASoC can only add kcontrols using codec and platform component device
handles. It's also desirable to add kcontrols for DAIs (i.e. McBSP) and for
SoC card machine drivers too. This allows the kcontrol to have a direct handle to
the parent ASoC component DAI/SoC Card/Platform/Codec device and hence easily
get it's private data.
This change makes snd_soc_add_controls() static and wraps it in the folowing
calls (card and dai are new) :-
snd_soc_add_card_controls()
snd_soc_add_codec_controls()
snd_soc_add_dai_controls()
snd_soc_add_platform_controls()
This patch also does a lot of small mechanical changes in individual codec drivers
to replace snd_soc_add_controls() with snd_soc_add_codec_controls().
It also updates the McBSP DAI driver to use snd_soc_add_dai_controls().
Finally, it updates the existing machine drivers that register controls to either :-
1) Use snd_soc_add_card_controls() where no direct codec control is required.
2) Use snd_soc_add_codec_controls() where there is direct codec control.
In the case of 1) above we also update the machine drivers to get the correct
component data pointers from the kcontrol (rather than getting the machine pointer
via the codec pointer).
Signed-off-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is preparation for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Current FSI got each PortA/B parameter by porta_flags/portb_flags from platform.
And .set_rate function was shared for PortA/B.
This structure was not readable and not flexible.
This patch adds sh_fsi_port_info, and its own settings was added on each platform.
it is preparation for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
is_play should be kept as local valuable.
it prepare cleanup for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds struct fsi_stream_handler and defined fsi_pio_push/pop_handler.
these are controled by fsi_steam_xxx() function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_get_current_fifo_samples() uses fsi_stream instead of is_play.
This is just prepare cleanup for DMAEngine support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch re-define fsi_is_play() and fsi_stream_is_play().
fsi_data_pop/push() function keeps direct value of "is_play" at this point,
but it will be removed soon.
This is just prepare cleanup for DMAEngine support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch modify fsi_pio_get_area() parameter to use
struct fsi_stream, and used it on fsi_fifo_data_ctrl().
This is just prepare cleanup for DMAEngine support.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is preparation for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is preparation for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
fsi_fifo_init() is called only from fsi_hw_startup()
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is preparation for DMAEngine support
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Next transfer data size of "push" and "pop" had calculated on shared function.
But it was not readable code.
This patch divided it into for push, and for pop.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch gathered fsi_stream_xxx() functions in order to make it readable.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All DAPM routes are configured via device tree, and there is no need in
DAPM route structures in board file.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch is adding device tree support of headset autodetection on PAZ00 board.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the standard logging macros and use dev_ variants where we can, also
reporting error codes whenever we report an error. These changes (the
error codes in particular) make it noticeably easier to figure out what
went wrong just from the basic dmesg output.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
The second line output mixer has the controls for the line input bypasses
in the opposite order.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Use the dai_link's dai_fmt attribute to setup the DAI format instead of doing
this manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For master mode, set Output [X|A|V]SP_SCLK Sourcing Mode to MCLK Mode.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
.. several days delayed. No reason, I just didn't think of it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iQEcBAABAgAGBQJPKF4KAAoJEHm+PkMAQRiGw/YH+wXg2DpZUuHeBK52zMGlJBPc
DzX11/Uan3Y07gM0JbDzuVxwjX4vdxR2bV6r1qsLP8JEUnE8jyFC32DBGi5WAht7
F4KU/Uov2Ds5/wzvY4Iuo01C+JftQHXuy/Sbhck1d0LI0yjLejRaw+zuJv0x2/eS
7YqV+KTGE1lDuJs/Gyq1Vqr1g9831AuS1tv/g3gaqBuN6TcPBFCocaVxzwrUc+y6
94h26XbbOhQRIz38oqUkiqAGnvYS61ocyBcEiRHf0dXkNSDIINqlgukvd7YTXouA
jj/w/DWpMRcQuYAgqkrurr9+yWC9hVQcsvvQ5sAQnIPcxoR868sg1pO8Oheq+1g=
=kUzV
-----END PGP SIGNATURE-----
Merge tag 'v3.3-rc2' into for-3.4
A reasonable amount of new development is causing fiddly merge conflicts
between different resource management changes (mostly fixing bugs in
resource management due to noticing things while doing enhancements in
the same area).
Linux 3.3-rc2
.. several days delayed. No reason, I just didn't think of it.
This patch implements device tree support for Tegra boards with ALC5632
codec.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For later wm_hubs devices we have much less need to keep the biases up
even when using single ended line outputs so flag idle_bias_off for
everything except the WM8993 and WM8994.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the same pm_ops for all system suspend and resume paths. This isn't
ideal for suspend to disk with older CODECs as we'll suspend and then
resume the CODEC before powering off all of which takes a long time due
to VMID ramps but it's very simple to implement and for modern CODECs the
overhead should be minimal.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
If an idle_bias_off device is in any state other than off then it is still
active for some reason (typically a low power function such as accessory
detection). This wasn't an issue when the feature was implemented as we
always went to _ON for any active function, subsequent power improvements
have changed things.
With the modern way of doing things we should overhaul the infrastructure
to allow devices to explicitly take references for these functions but
that's a much more invasive change and will require driver updates to
deploy, this will bring the framework into line with the existing driver
set before we do that work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Now we've switched over to regmap the ASoC level cache sync will be
ineffectual and potentially harmful as there is no longer an ASoC level
cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
IN1L/R is routed to both line output mixers, we don't route IN1 to LINEOUT1
and IN2 to LINEOUT2.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
The runtime PM core no longer requires any callbacks so don't provide
empty ones for it any more.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Mute Switch should be called Playback Switch to match the volume
and the regmap core has been updated so we don't need to mark all the
registers as non-volatile.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Add a driver supporting the volume control and the mute pin. Shdn pin
and DAPM are not taken care of yet.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Openmoko GTA01 machine has been removed from the machine ID database,
so we need to remove references to it as well.
Without that fix we have:
sound/soc/samsung/neo1973_wm8753.c: In function ‘neo1973_wm8753_init’:
sound/soc/samsung/neo1973_wm8753.c:325:2: error: implicit declaration of function ‘machine_is_neo1973_gta01’
Signed-off-by: Denis 'GNUtoo' Carikli <GNUtoo@no-log.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8962 has ground referenced and class D outputs so can happily go
down to BIAS_OFF without a large startup time.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since commit 33c5f969 "ASoC: Allow idle_bias_off to be specified in CODEC
drivers", now we can set idle_bias_off flag in struct snd_soc_codec_driver
for devices can unconditionally support idle_bias_off.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For optimal performance the single ended line outputs require that the
line output VMID buffer be enabled.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Report any accessory with a low impedance as a headphone, previously
anything other than a short or microphone would not be reported at all.
The most likely reason is a microphone with incorrect polarity.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we get an indeterminate impedance with both headset polarities then
give up and report the accessory as a headphone rather than continually
retrying.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using pm_runtime to decide if the device should go into full power down
has the dual advantage of allowing easier integration with non-DAPM
reasons to power on the device (like the FLL) and allowing userspace to
control the final power down which is useful for tuning retention of
DSP firmware.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator has no power control itself and so shouldn't cause a
power up of the device.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't really care if any action is taken immediately so let the PM
core defer things if it wants to.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM2200 is a low power mobile CODEC with enhanced Wolfson myZone
Ambient Noise Cancellation (ANC) intended for mobile telephony
applications.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Modern devices allow systems to enable and disable individual supplies on
the device, allowing additional power saving by switching off regulators
which power portions of the device which are not currently in use. Add a
new SND_SOC_DAPM_REGULATOR_SUPPLY widget type factoring out the code for
managing such widgets from individual drivers.
The widget name will be used as the supply name when requesting the
regulator from the regulator API.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Enable ASoC audio support for OMAP4 based machines with
twl6040 codec via the omap-abe-twl6040 machine driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Avoid using hardwired configuration for MCLK frequency.
Different board design might use other MCLK frequency.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Disable the not connected pins on the board based on the
received platform data.
DO not register the jack function on boards, which does not have
means to detect it (jack is always connected).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can have machines without DMIC connected. In this case there is
no need to create amother (unusable) capture PCM on the card.
The existence of the DMIC connection can be checked via
pdata->has_dmic.
Select the correct dai_link structure for the card based on
pdata->has_dmic.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SDP4430 is a reference platform, and as such it has all possible
audio routing implemented.
Correct the DAPM routing to be complete.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In order to avoid breakage change the omap-abe-twl6040
machine driver's routing.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert the OMAP4 ABE/TWL6040 machine driver to platform
driver.
For the card name use the string provided via platform data.
The card's name for OMAP4 SDP4430 has been changed:
SDP4430 -> OMAP4-SDP4430
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Change the internal prefixes within the driver from sdp4430.
At he same time correct the Kconfig text as well.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The same machine driver will support other boards
with similar audio configuration (OMAP4, ABE, twl6040).
Rename the driver to have more generic name.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to write the configuration for each microphone to a different
register.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
When we have identified an accessory make sure we've flagged that we've
done so in order to make sure we always report buttons and don't continue
to polarity flip.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As per discussion we can safely ignore the 8 and 16 bit sample
sizes when applying the msbits constraint.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When the hardware is configured with one or both of the IN4 inputs used
for DC measurement (with no DC blocking capacitor connected) then we can
improve power consumption slightly in idle modes by applying a register
write sequence. Provide platform data to enable this, implemented using
a regmap patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In wm2000_i2c_probe(), if we take the true branch in
"
ret = snd_soc_register_codec(&i2c->dev, &soc_codec_dev_wm2000,
NULL, 0);
if (ret != 0)
goto err_fw;
"
then we'll release_firmware(fw) at the 'err_fw' label. But we've already
done that just a few lines above. That's a use-after-free bug.
This patch restructures the code so that we always call
release_firmware(fw) before leaving the function, but only ever call
it once.
This means that we have to initialize 'fw' to NULL since some paths
may now end up calling it without having called request_firmware(),
but since request_firmware() deals gracefully with NULL pointers, we
are fine if we just NULL initialize it.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
To print a value of type size_t one should use %zd, not %d.
Signed-off-by: Jesper Juhl <jj@chaosbits.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix below build warning when CONFIG_HOTPLUG is not set.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c:1062: warning: ‘alc5623_i2c_remove’ defined but not used
CC sound/soc/codecs/alc5632.o
sound/soc/codecs/alc5632.c:1112: warning: ‘alc5632_i2c_remove’ defined but not used
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Convert to table based DAPM and control init.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We should be allowing a 5ms delay after the charge pump is started in
order to ensure it has finished ramping.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
Visstrim_M10 has an external class D amplifier.
This patch provides support for controlling the 4
possible gain levels and per channel muting.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The problem was introduced due to the obscure formatting some of the
older drivers use.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If a driver is using regmap directly ensure that we're coherent with
non-ASoC register updates by using the regmap API directly to do our
read/modify/write cycles. This will bypass the ASoC cache but drivers
using regmap directly should not be using the ASoC cache.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
On a mx28evk board the following errors happens on mxs-sgtl5000 probe:
[ 0.660000] saif0_clk_set_rate: divider writing timeout
[ 0.670000] mxs-sgtl5000: probe of mxs-sgtl5000.0 failed with error -110
[ 0.670000] ALSA device list:
[ 0.680000] No soundcards found.
This timeout happens because clk_set_rate will result in writing to the DIV bits
of register HW_CLKCTRL_SAIF0 with the saif clock gated (CLKGATE bit set to one).
MX28 Reference states the following about CLKGATE:
"The DIV field can change ONLY when this clock gate bit field is low."
So call clk_prepare_enable prior to clk_set_rate to fix this problem.
After this change the mxs-saif driver can be correctly probed and audio is functional.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is more what the device model wants us to do and will allow use by
non-audio functions before the audio part of the device has come up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This will allow us to move the interrupt allocation out of the ASoC part
of the driver and simplifies the locking by removing any reliance in the
bulk of the interrupt path on the big CODEC lock.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
McPDM internal FIFO is 24 bit wide. From the 32 bit sample
8 bit is discarded. Let application know about this
via msbits constraint.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Core can set the msbits constraint in behalf of the dai.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
