This BUG_ON is unneeded since the ->handler != NULL check is performed in
ide_set_handler().
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Replace the ide-floppy packet commands opcode defines with the generic ones.
Add a missing GPCMD_WRITE_12 (opcode 0xaa) to the generic ones in cdrom.h. The
last one can be found in the current version of INF-8090, p.905.
[ Bart: Tejun's libata patch also adding GPCMD_WRITE_12 got merged first ]
Signed-off-by: Borislav Petkov <bbpetkov@yahoo.de>
Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->cable_detect method to ide_hwif_t.
* Call the new method in ide_init_port() if:
- the host supports UDMA modes > UDMA2 ('hwif->ultra_mask & 78')
- DMA initialization was successful (if hwif->dma_base is not set
ide_init_port() sets hwif->ultra_mask to zero)
- "idex=ata66" is not used ('hwif->cbl != ATA_CBL_PATA40_SHORT')
* Convert PCI host drivers to use ->cable_detect method.
While at it:
* Factor out cable detection to separate functions (if not already done).
* hpt366.c/it8213.c/slc90e66.c:
- don't check cable type if "idex=ata66" is used
* pdc202xx_new.c:
- add __devinit tag to pdcnew_cable_detect()
* pdc202xx_old.c:
- rename pdc202xx_old_cable_detect() to pdc2026x_old_cable_detect()
- add __devinit tag to pdc2026x_old_cable_detect()
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove 'struct pci_dev *dev' argument from ide_hwif_setup_dma().
* Un-static ide_hwif_setup_dma() and add CONFIG_BLK_DEV_IDEDMA_PCI=n version.
* Add 'const struct ide_port_info *d' argument to ide_device_add[_all]().
* Factor out generic ports init from ide_pci_setup_ports() to ide_init_port(),
move it to ide-probe.c and call it in in ide_device_add_all() instead of
ide_pci_setup_ports().
* Move ->mate setup to ide_device_add_all() from ide_port_init().
* Add IDE_HFLAG_NO_AUTOTUNE host flag for host drivers that don't enable
->autotune currently.
* Setup hwif->chipset in ide_init_port() but iff pi->chipset is set
(to not override setup done by ide_hwif_configure()).
* Add ETRAX host handling to ide_device_add_all().
* cmd640.c: set IDE_HFLAG_ABUSE_* also for CONFIG_BLK_DEV_CMD640_ENHANCED=n.
* pmac.c: make pmac_ide_setup_dma() return an error value and move DMA masks
setup to pmac_ide_setup_device().
* Add 'struct ide_port_info' instances to legacy host drivers, pass them to
ide_device_add() calls and then remove open-coded ports initialization.
Reviewed-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Setup ->mate and ->channel in ide_pci_setup_ports() instead of
in ide_hwif_configure().
* Make 'port' parameter for ide_hwif_configure() 'unsigned int'.
* Separate PCI specific init from generic init in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always set DMA masks in ide_pci_setup_ports() to make sure that the valid
masks for a host are set.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Nowadays IDE core always provides drive ID and ide-disk always setups
drive->capacity64 so this quirk is no longer needed.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Don't override the cable type if the "idex=ata66" parameter was used.
While at it:
* atiixp.c: factor out cable detection to atiixp_cable_detect() from
init_hwif_atiixp().
* cs5535.c: pass 'ide_hwif_t *hwif' instead of 'struct pci_dev *dev' to
cs5535_cable_detect().
* scc_pata.c: factor out cable detection to scc_cable_detect() from
init_hwif_scc() and remove incorrect comment.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
The host driver must set hwif's ->no_io_32bit setting not drive's one
(ide_port_tune_devices() overrides drive's setting).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On DTC2278 32-bit I/O has to be enabled for both devices on the port
so always enable it during init time and disallow further changes.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
sg_dma_len(sg) is invalid before the s/g list is DMA-mapped.
This fixes a post 2.6.24 regression which prevents access to SBP-2
devices on several architectures, introduced by "ieee1394: sbp2: s/g
list access cosmetics", commit 825f1df545.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.infradead.org/battery-2.6:
apm_power: check I.intval for zero value, we use it as the divisor
MAINTAINERS: remove kernel-discuss@handhelds.org list
pda_power: implement polling
pda_power: various cleanups
apm_power: support using VOLTAGE_* properties for apm calculations
pda_power: add suspend/resume support
power_supply: add few more values and props
pda_power: only register available psu
power: fix incorrect unregistration in power_supply_create_attrs error path
power: remove POWER_SUPPLY_PROP_CAPACITY_LEVEL
[BATTERY] power_supply_leds: use kasprintf
[BATTERY] Every file should include the headers containing the prototypes for its global functions.
* 'suspend' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (38 commits)
suspend: cleanup reference to swsusp_pg_dir[]
PM: Remove obsolete /sys/devices/.../power/state docs
Hibernation: Invoke suspend notifications after console switch
Suspend: Invoke suspend notifications after console switch
Suspend: Clean up suspend_64.c
Suspend: Add config option to disable the freezer if architecture wants that
ACPI: Print message before calling _PTS
ACPI hibernation: Call _PTS before suspending devices
Hibernation: Introduce begin() and end() callbacks
ACPI suspend: Call _PTS before suspending devices
ACPI: Separate disabling of GPEs from _PTS
ACPI: Separate invocations of _GTS and _BFS from _PTS and _WAK
Suspend: Introduce begin() and end() callbacks
suspend: fix ia64 allmodconfig build
ACPI: clear GPE earily in resume to avoid warning
Suspend: Clean up Kconfig (V2)
Hibernation: Clean up Kconfig (V2)
Hibernation: Update messages
Suspend: Use common prefix in messages
Hibernation: Remove unnecessary variable declaration
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/pci-2.6: (64 commits)
PCI: make pci_bus a struct device
PCI: fix codingstyle issues in include/linux/pci.h
PCI: fix codingstyle issues in drivers/pci/pci.h
PCI: PCIE ASPM support
PCI: Fix fakephp deadlock
PCI: modify SB700 SATA MSI quirk
PCI: Run ACPI _OSC method on root bridges only
PCI ACPI: AER driver should only register PCIe devices with _OSC
PCI ACPI: Added a function to register _OSC with only PCIe devices.
PCI: constify function pointer tables
PCI: Convert drivers/pci/proc.c to use unlocked_ioctl
pciehp: block new requests from the device before power off
pciehp: workaround against Bad DLLP during power off
pciehp: wait for 1000ms before LED operation after power off
PCI: Remove pci_enable_device_bars() from documentation
PCI: Remove pci_enable_device_bars()
PCI: Remove users of pci_enable_device_bars()
PCI: Add pci_enable_device_{io,mem} intefaces
PCI: avoid save the same type of cap multiple times
PCI: correctly initialize a structure for pcie_save_pcix_state()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (128 commits)
USB: fix codingstyle issues in drivers/usb/core/*.c
USB: fix codingstyle issues in drivers/usb/core/message.c
USB: fix codingstyle issues in drivers/usb/core/hcd-pci.c
USB: fix codingstyle issues in drivers/usb/core/devio.c
USB: fix codingstyle issues in drivers/usb/core/devices.c
USB: fix codingstyle issues in drivers/usb/core/*.h
USB: fix codingstyle issues in include/linux/usb/
USB: fix codingstyle issues in include/linux/usb.h
USB: mark USB drivers as being GPL only
USB: use a real vendor and product id for root hubs
USB: mount options: fix usbfs
USB: Fix usb_serial_driver structure for Kobil cardreader driver.
usb: ehci should use u16 for isochronous intervals
usb: ehci, remove false clear-reset path
USB: Use menuconfig objects
usb: ohci-sm501 driver
usb: dma bounce buffer support
USB: last abuses of intfdata in close for usb-serial drivers
USB: kl5kusb105 don't flush to logically disconnected devices
USB: oti6858: cleanup
...
- handle spurious interrupts correctly;
- get rid of pda_power_supplies array, use two variables instead;
- factor out psy_changed() function, it will be used for polling.
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
It's pretty dummy, but useful for batteries for which we can only
get voltages.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Add LiMn (one of the most common for small non-rechargable batteries)
battery technology and voltage_min/_max properties support.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Currently pda-power adds both ac and usb power supply units.
This patch fixes it so that psu are added only if they are enabled.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
In power_supply_create_attrs(), we create static attributes as referenced
by power_supply_static_attrs[i]. After that, if we fail, we unregister
via power_supply_static_attrs[psy->properties[i]]. This is incorrect, as
psy->properties has absolutely no bearing on static attribs. This patch
fixes it to unregister the correct attrib.
Another line which was unnecessarily line wrapped is also unwrapped.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CAPACITY_LEVEL stuff defines various levels of charge; however, what
is the difference between them? What differentiates between HIGH and NORMAL,
LOW and CRITICAL, etc?
As it appears that these are fairly arbitrary, we end up making such policy
decisions in the kernel (or in hardware). This is the sort of decision that
should be made in userspace, not in the kernel.
If the hardware does not support _CAPACITY and it cannot be easily calculated,
then perhaps the driver should register a custom CAPACITY_LEVEL attribute;
however, userspace should not become accustomed to looking for such a thing,
and we should certainly not encourage drivers to provide CAPACITY_LEVEL
stubs.
The following removes support for POWER_SUPPLY_PROP_CAPACITY_LEVEL. The
OLPC battery driver is the only driver making use of this, so it's
removed from there as well.
Signed-off-by: Andres Salomon <dilinger@debian.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use kasprintf instead of kmalloc()-strcpy()-strcat().
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Anton Vorontsov <cbou@mail.ru>
Make acpi_sleep_prepare() static and cause it to print a message
specifying the ACPI system sleep state to be entered (helpful for
debugging the suspend/hibernation code).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order. The current
hibernation code follows ACPI 2.0 in that respect which may cause some
ACPI 1.0x systems to hang during hibernation (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).
Make the hibernation code execute _PTS before putting devices into
low power states (ie. in accordance with ACPI 1.0x) with the
possibility to override that using the 'acpi_new_pts_ordering' kernel
command line option.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Introduce global hibernation callback .end() and rename global
hibernation callback .start() to .begin(), in analogy with the
recent modifications of the global suspend callbacks.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The ACPI 1.0 specification wants us to put devices into low power
states after executing the _PTS global control method, while ACPI
2.0 and later want us to do that in the reverse order. The current
suspend code follows ACPI 2.0 in that respect which causes some
ACPI 1.0x systems to hang during suspend (ref.
http://bugzilla.kernel.org/show_bug.cgi?id=9528).
Make the suspend code execute _PTS before putting devices into low
power states (ie. in accordance with ACPI 1.0x) and provide a command
line option to override the default if need be.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
The preparation to enter an ACPI system sleep state is now tied to
the disabling of GPEs, but the GPEs should not be disabled before
suspending devices. Since on ACPI 1.0x systems the _PTS global
control method should be executed before suspending devices, we
need to disable GPEs separately.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
The execution of ACPI global control methods _GTS and _BFS is
currently tied to the preparation to enter a sleep state and to the
leaving of the sleep state, respectively. However, these functions
are called before disabling the nonboot CPUs and after enabling
them, respectively (in fact, on ACPI 1.0x systems the first of them
ought to be called before suspending devices), while according to the
ACPI specification, _GTS is to be executed right prior to entering
the system sleep state and _BFS is to be executed right after the
platfor firmware has returned control to the OS on wake up.
Move the execution of _GTS and _BFS to the right places.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
On ACPI systems the target state set by acpi_pm_set_target() is
reset by acpi_pm_finish(), but that need not be called if the
suspend fails. All platforms that use the .set_target() global
suspend callback are affected by analogous issues.
For this reason, we need an additional global suspend callback that
will reset the target state regardless of whether or not the suspend
is successful. Also, it is reasonable to rename the .set_target()
callback, since it will be used for a different purpose on ACPI
systems (due to ACPI 1.0x code ordering requirements).
Introduce the global suspend callback .end() to be executed at the
end of the suspend sequence and rename the .set_target() global
suspend callback to .begin().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Wakeup GPE hasn't a handler. If system is waked up by such GPE like a
USB hotplug, I saw a lot of error reporting the GPE hasn't handler.
acpi_leave_sleep_state will clear the GPE but it's too late, we should
do it before interrupt is re-enabled.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
When trying to debug a suspend failure I started implementing
PM_TRACE for powerpc. I then noticed that I'm debugging a suspend
failure and so PM_TRACE isn't useful at all, but thought that
nonetheless this could be useful in the future.
Basically, to support PM_TRACE, you add a Kconfig option that
selects PM_TRACE and provides the infrastructure as per the
help text of PM_TRACE.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Some code in acpi_hibernation_finish() was moved to acpi_hibernation_leave(),
but the old copy had been left (it's harmless, but also useless). Remove it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
This moves the pci_bus class device to be a real struct device and at
the same time, place it in the device tree in the correct location.
Note, the old "bridge" symlink is now gone, but this was a non-standard
link and no userspace program used it. If you need to determine the
device that the bus is on, follow the standard device symlink, or walk
up the device tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Express ASPM defines a protocol for PCI Express components in the D0
state to reduce Link power by placing their Links into a low power state
and instructing the other end of the Link to do likewise. This
capability allows hardware-autonomous, dynamic Link power reduction
beyond what is achievable by software-only controlled power management.
However, The device should be configured by software appropriately.
Enabling ASPM will save power, but will introduce device latency.
This patch adds ASPM support in Linux. It introduces a global policy for
ASPM, a sysfs file /sys/module/pcie_aspm/parameters/policy can control
it. The interface can be used as a boot option too. Currently we have
below setting:
-default, BIOS default setting
-powersave, highest power saving mode, enable all available ASPM
state
and clock power management
-performance, highest performance, disable ASPM and clock power
management
By default, the 'default' policy is used currently.
In my test, power difference between powersave mode and performance mode
is about 1.3w in a system with 3 PCIE links.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the fakephp driver is used to emulate removal of a PCI device by
writing text string "0" to the "power" sysfs attribute file, this causes
its parent directory and its contents (including the "power" file) to be
deleted before the write operation returns. Unfortunately, it ends up
in a deadlock waiting for itself to complete.
The deadlock is as follows: sysfs_write_file calls flush_write_buffer
which calls sysfs_get_active_two before calling power_write_file in
pci_hotplug_core.c via the sysfs store operation. The power_write_file
function calls disable_slot in fakephp.c via the slot operation. The
disable_slot function calls remove_slot which calls pci_hp_deregister
(back in pci_hotplug_core.c) which calls fs_remove_slot which calls
sysfs_remove_file to remove the "power" file. The sysfs_remove_file
function calls sysfs_hash_and_remove which calls sysfs_addrm_finish
which calls sysfs_deactivate. The sysfs_deactivate function sees that
something has an active reference on the sysfs_dirent (from the
previous call to sysfs_get_active_two back up the call stack somewhere)
so waits for the active reference to go away, which is of course
impossible.
The problem has been present since 2.6.21.
This patch breaks the deadlock by queuing work queue items on a single-
threaded work queue to remove a slot from sysfs, and to rescan the PCI
buses. There is also some protection against disabling a slot that is
already being removed.
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Cc: Kristen Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SB700 SATA MSI bug will be fixed in SB700 revision A21 at hardware
level, but the SB700 revision older than A21 will also be found in the
market. This patch modify the original quirk commit
bc38b411fe instead of withdrawing it.
The patch also removes quirk to 0x4395 because 0x4395 is SB800 device
ID.
Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
According to the PCI Firmware Specification Revision 3.0 section 4.5, _OSC
should only be called on a root brdige. Here is the relevant passage: "The
_OSC interface defined in this section applies only to Host Bridge ACPI
devices that originate PCI, PCI-X, or PCI Express hierarchies". Changed the
code to find the parent root bridge of the device and call _OSC on that.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
AER is only used with PCIe devices so we should only check PCIe devices for
_OSC support.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function pci_osc_support_set() traverses every root bridge when
checking for _OSC support for a capability. It quits as soon as it finds a
device/bridge that doesn't support the requested capability. This won't
work for systems that have mixed PCI and PCIe bridges when checking for
PCIe features. I split this function into two -- pci_osc_support_set() and
pcie_osc_support_set(). The latter is used when only PCIe devices should be
traversed.
Signed-off-by: Andrew Patterson <andrew.patterson@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Disable Bus Master, SERR# and INTx to ensure that no new Requests will
be generated from the device before turning power off, in accordance
with the specification.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Set Bad DLLP Mask bit in Correctable Error Mask Register during
turning power off the slot.
This is the workaround against Bad DLLP error that sometimes happen
during turning power off on the slot which conforms to PCI Express
1.0a spec. The cause of this error seems that PCI Express 1.0a spec
doesn't have the following consideration that was added to PCI Express
1.1 spec.
"If the port is associated with a hot-pluggable slot (Hot-Plug
Capable bit in the Slot Capabilities register set to 1b), and
Power Controller Control bit in Slot Control register is 1b(Off),
then any transition to DL Inactive must not be considered an
error."
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After turning power off, we must wait for at least 1 second *before*
LED operation.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that all in-tree users are gone, this removes pci_enable_device_bars()
completely.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch converts users of pci_enable_device_bars() to the new
pci_enable_device_{io,mem} interface.
The new API fits nicely, except maybe for the QLA case where a bit of
code re-organization might be a good idea but I prefer sticking to the
simple patch as I don't have hardware to test on.
I'll also need some feedback on the cs5520 change.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pci_enable_device_bars() interface isn't well suited to PCI
because you can't actually enable/disable BARs individually on
a device. So for example, if a device has 2 memory BARs 0 and 1,
and one of them (let's say 1) has not been successfully allocated
by the firmware or the kernel, then enabling memory decoding
shouldn't be permitted for the entire device since it will decode
whatever random address is still in that BAR 1.
So a device must be either fully enabled for IO, for Memory, or
for both. Not on a per-BAR basis.
This provides two new functions, pci_enable_device_io() and
pci_enable_device_mem() to replace pci_enable_device_bars(). The
implementation internally builds a BAR mask in order to be able
to use existing arch infrastructure.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Avoid adding the same type of cap multiple times, otherwise we will see dead loop.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
save_state->cap_nr should be correctly set, otherwise we can't find the
saved cap at resume.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pci_save/store_state has multiple bugs, which will cause cap can't be
saved/restored correctly. Below 3 patches fix them.
fix the typo in pci_save_pcix_state
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Convert quirk printks to dev_printk().
I made the MSI disable messages a little more consistent:
- always use "disabled", not "deactivated"
- specify "device MSI disabled" or "subordinate MSI disabled" when
disabling MSI for only a specific device or subordinate bus
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of printing this:
PCI: Calling quirk c023b250 for 0000:00:00.0
we can print this:
pci 0000:00:00.0: calling quirk 0xc023b270: quirk_cardbus_legacy+0x0/0x30()
The address is superfluous because sprint_symbol() includes the
address if the symbol lookup fails, but this is the same style used
in do_initcalls() and pnp_fixup_device().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Check that the e100 is in the D0 power state. If it's not, it won't
respond to MMIO accesses and we end up with master-abort machine
checks on some platforms.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the following problem present with older gcc versions:
<-- snip -->
...
CC drivers/pci/msi.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/pci/msi.c:692: warning: weak declaration of `arch_msi_check_device' after first use results in unspecified behavior
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/pci/msi.c:704: warning: weak declaration of `arch_setup_msi_irqs' after first use results in unspecified behavior
/home/bunk/linux/kernel-2.6/git/linux-2.6/drivers/pci/msi.c:724: warning: weak declaration of `arch_teardown_msi_irqs' after first use results in unspecified behavior
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds appropriate casts to avoid a warning and print the correct
values in pr_debug.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current pci_assign_unassigned_resources() code doesn't work properly
on 32 bits platforms with 64 bits resources. The main reason is the use
of unsigned long in various places instead of resource_size_t.
This is a pre-requisite for making powerpc use the generic code instead of
its own half-useful implementation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove needless members from struct controller. This has no functional
changes.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
acpi_get_name() is called before and after dbg(). The latter is
useless and should be removed.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earlier patches to split out the hardware init for PCIe hotplug resulted in
some one-time initializations being redone on every resume cycle. Eg.
irq/polling initialization.
This patch splits the hardware init into two parts, and separates the
one-time initializations from those so that they only ever get done once,
as intended.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make use of the previously split out pcie_init_enable_events() function
to reinitialize the hotplug hardware on resume from suspend, but only
when pciehp_force==1. Otherwise behaviour is unmodified.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Split out the hotplug hardware initialization code from pcie_init()
into pcie_init_enable_events(), without changing any functionality.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix pciehp_probe() to deal with ExpressCard cards
that were inserted prior to the driver being loaded.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Theodore Ts'o <tytso@mit.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI error recovery usually involves the PCI adapter being reset.
If the device is using MSI, the reset will cause the MSI state
to be lost; the device driver needs to restore the MSI state.
The pci_restore_msi_state() routine is currently protected
by CONFIG_PM; remove this, and also export the symbol, so
that it can be used in a modle.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix presentation of the slot number in the /sys/bus/pci/slots
directory to match that used in the majority of other drivers.
> Greg said:
> How is anyone supposed to write sane managability tools in the
> presence
> of such anarchy?
>
> > ~ # cat /sys/bus/pci/slots/0000:00:02.2/phy_location
> > U787A.001.DNZ00Z5-P1-C2
>
> Right. This should look like:
>
> # cat /sys/bus/pci/slots/U787A.001.DNZ00Z5-P1-C2/address
> 0000:00:02
This patch implements exactly what you describe. Boot tested.
I assume you really mean it -- if so, then please review and
ack the patch !?
I have absolutely no clue if this breaks any existing IBM tools.
I'm pretty sure it doesn't ... but attention Mike Strosaker! does it?
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Cc: <strosake@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Unhide the SMBus on the HP xw4100. This gives access to a hardware
monitoring chip (ADT7463) and to the memory module SPD EEPROMs. I
checked that ACPI wasn't accessing the SMBus, so it should be safe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add and changes a few sanity checks in dmar.c.
1. The haw field in ACPI DMAR table in VT-d spec doesn't describe the
range of haw. But since DMA page size is 4KB in DMA remapping, haw
should be at least 4KB. The current VT-d code in dmar.c returns failure
when haw==0. This sanity check is not accurate and execution can pass
when haw is less than one page size 4KB. This patch changes the haw
sanity check to validate if haw is less than 4KB.
2. Add dmar_rmrr_units verification.
3. Add parse_dmar_table() verification.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Fenghua Yu <fenghua.yu@intel.com>
Acked-by: mark gross <mgross@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove lots of space-before-) instances. Perhaps these were a workaround for
problems in some long-dead cpp version.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's already a prototype for pci_scan_child_bus() at the correct place in
pci.h, so there's no reason for an additional one.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
sys_pciconfig_{read,write}() are protected against PCI removal with the
reference count in struct pci_dev. The concurrency of
pci_user_{read,write}_config_* functions are already protected by pci_lock
in drivers/pci/access.c.
Signed-off-by: Diego Woitasen <diego@woitasen.com.ar>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In an attempt to ensure memory allocation from the local node, the pci
driver temporarily replaces the current task's memory policy with the
system default policy. Trying to be a good citizen, the driver then call's
mpol_get() on the new policy. When it's finished probing, it undoes the
'_get by calling mpol_free() [on the system default policy] and then
restores the current task's saved mempolicy.
A couple of issues here:
1) it's never necessary to set a task's mempolicy to the
system default policy in order to get system default
allocation behavior. Simply set the current task's
mempolicy to NULL and allocations will fall back to
system default policy.
2) we should never [need to] call mpol_free() on the system
default policy. [I plan on trapping this with a VM_BUG_ON()
in a subsequent patch.]
This patch removes the calls to mpol_get() and mpol_free()
and uses NULL for the temporary task mempolicy to effect
default allocation behavior.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Christoph Lameter <clameter@sgi.com>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCI Bus Parking and PCI Master read caching on the VIA CX700 is buggy and
can lead to problems such as USB2.0 packet loss if a VT6212L controller
is on the PCI bus. It's disabled by default, but some BIOSes turn these
features on and this patch reverts the configuration to the safe defaults.
Signed-off-by: Tim Yamin <tim.yamin@zonbu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't read the revision ID unnecessary since the PCI subsystem
fills this field in already.
Updated to fix a thinko bug in a previously sent patch.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, fakephp will claim all devices; we really only want it
to claim those not in slots.
Signed-off-by: Alex Chiang <achiang@hp.com>
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove EXPERIMENTAL from PCI Hot Plug.
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thank you so much for your check & advise.
This time, I've tried on ibmphp_core.c, is it OK?
Signed-off-by: Joonwoo Park <joonwpark81@gmail.com>
Signed-off-by: Kristen Carlson Accardi <kristen.c.accardi@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PCIE has a mechanism to wait for Non-Posted request to complete. I think
pci_disable_device is a good place to do this.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Native PME is capability of root port or root complex event collector.
It's not determined by PCI PME capability.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch #if 0's the following unused global functions:
- rom.c: pci_map_rom_copy()
- rom.c: pci_remove_rom()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch makes the needlessly global pci_restore_bars() static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (100 commits)
ide: move hwif_register() call out of ide_probe_port()
ide: factor out code for tuning devices from ide_probe_port()
ide: move handling of I/O resources out of ide_probe_port()
ide: make probe_hwif() return an error value
ide: use ide_remove_port_from_hwgroup in init_irq()
ide: prepare init_irq() for using ide_remove_port_from_hwgroup()
ide: factor out code removing port from hwgroup from ide_unregister()
ide: I/O resources are released too early in ide_unregister()
ide: cleanup ide_system_bus_speed()
ide: remove needless zeroing of hwgroup fields from init_irq()
ide: remove unused ide_hwgroup_t fields
ide_platform: remove struct hwif_prop
ide: remove hwif->present manipulations from hwif_init()
ide: move wait_hwif_ready() documentation in the right place
ide: fix handling of busy I/O resources in probe_hwif()
<linux/hdsmart.h> is not used by kernel code
ide: don't include <linux/hdsmart.h>
ide-floppy: cleanup header
ide: update/add my Copyrights
ide: delete filenames/versions from comments
...
Over two years ago, the Linux USB developers stated that they believed
there was no way to create a USB kernel driver that was not under the
GPL. This patch moves the USB apis to enforce that decision.
There are no known closed source USB drivers in the wild, so this patch
should cause no problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Turns out that a company is out there using the vendor id of 0x0000 in
the wild, so use a real vendor/product id for the root hubs.
Now that the Linux Foundation has a real vendor id, we use that, and the
first product id:
0x1d6b is the vendor id of the Linux Foundation
0x0001 is the product id for Linux 1.1 root hubs
0x0002 is the product id for Linux 2.0 root hubs
The usb.ids file has already been updated with these values.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The device setup did miss to initialize the num_interrupt_out field, thus
failing to successfully complete the probe function.
Signed-off-by: Stefan Bader <stefan.bader@canonical.com>
Cc: stable <stable@kernel.org>
Cc: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
While most isochronous endpoints have short polling intervals, the
EHCI driver won't necessarily handle larger ones correctly.
This patch switches to use a "u16" to represent those periods, not
a u8, since it can always work: the largest expressible period
is 2^15 units ... not the previous too-short limit of 128 frames
(full or low speeds) or microframes (high speed, 32 frames).
This bug is essentially theoretical, since the few ISO endpoints
I've seen which don't use one transfer per frame are high speed
ones using more than that (including high bandwidth, 24 KB/msec).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some of the "EHCI ports reset forever" problems may be explained by
code paths which wrongly flagged resets as complete. This removes
two such paths; the ehci_hub_status_data() path should be the only one
to have an effect, since it was already properly flagged on the other
path. (Issue noted by Minhyoung Kim <a9a9@lge.com>.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 04d06ad0f1 have added menuconfig support
for the whole USB Kconfig, but there are still menuconfig need for usb/serial,
usb/atm, and usb/gadget, so that the user can disable all the options in that
menu at once instead of having to disable each option separately.
Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: ohci-sm501 driver V2
This patch adds sm501 ohci support. It's all very straightforward with the
exception of dma_declare_coherent_memory() and HCD_LOCAL_MEM. Together they
are used to ensure that usb data is allocated using dma_alloc_coherent(),
and that only valid dma memory is used to allocate from. This driver is
a platform device, and the mfd driver sm501.c is already creating one
usb host controller instance per sm501.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
usb: dma bounce buffer support V4
This patch adds dma bounce buffer support to the usb core. These buffers
can be enabled with the HCD_LOCAL_MEM flag, and they make sure that all data
passed to the host controller is allocated using dma_alloc_coherent().
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
these drivers abused intfdata in close() as flags for binding.
That races with reprobing of those devices. This patch fixes that by using
the flag and the locks introduced with the patch against mos7720.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If disconnect() is called for a logical disconnect, no more IO must be
done after disconnect() returns, or the old and new drivers may conflict.
This patch avoids this by using the flag and lock introduced by the earlier
patch for the mos7720 driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Rename the copied buffer functions from pl2303 to oti6858 to avodi
confusion
- Initialise speeds properly
- Use modern baud rate handling
- Remove GSERIAL/SSERIAL ioctl hacks that reference termios unlocked
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this covers the rest of the obvious cases by using the flags
and locks to guard against disconnect which were introduced
in the earlier patch against mos7720.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If disconnect() is called for a logical disconnect, no more IO must be
done after disconnect() returns, or the old and new drivers may conflict.
This patch avoids this by using the flag and lock introduced by the earlier
patch for the mos7720 driver.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
in an error case memory already allocated must be freed again.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this driver uses usb_get_intfdata() == NULL as a test for disconnect().
You must not do that as this races with probe(). By the time you test
your erstwhile interface may already be somebody else's interface.
This fixes the close() method of cypress_m8 to use the recently introduced
flag and use locking against disconnect() where required in close().
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a problem where the mos7720 driver will make io to a device from
which it has been logically disconnected. It does so by introducing a flag by
which the generic usb serial code can signal the subdrivers their
disconnection and appropriate locking.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
People keep trying to add entries to this section of the driver for
things. That's what the Changelog is supposed to be for, not the .c
file.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When building an external module, the ezusb_* functions are not defined
if we haven't loaded any built'in module that use them (whiteheat,
keyspan, ...).
This patch allow to build those functions even if we only have selected
the usbserial generic driver.
Signed-off-by: Paul Chavent <paul.chavent@fnac.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1031) adds a short delay to the bus-suspend routine in
ehci-hcd. Without it some devices disconnect when they should
suspend.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1030b) moves a del_timer_sync() call outside the scope of a
spinlock, where it could cause a deadlock, and adds a new
del_timer_sync() call for the new IAA watchdog timer (it was omitted
by mistake).
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISO descriptors are allocated separately in proc_submiturb for a fetch
from user mode, then tucked at the end of URB. This seems like a dead code.
Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This has some bugfixes for the EHCI driver's ISO transfer scanning
logic. It was leaving ITDs and SITDs on the schedule too long, for
a few different reasons, which caused trouble.
(a) Look at all microframes for high speed transfers, not just
the ones we expect to have finished. This way transfers
ending mid-frame will complete without needing another IRQ.
This also minimizes bogus scheduling underruns (e.g. EL2NSYNC).
(b) When we encounter an ISO transfer (either speed, but this
hits mostly at full speed) that's not yet been completed,
immediately stop scanning; we've caught up to the hardware,
no matter what other indications might say.
(c) Always clean up ITDs (for high speed transfers) when the HC
is no longer running.
I'm not sure whether the last one has been observed before, but both
the others have been reported with "real world" audio and video code.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Small updates to the EHCI driver's ISO support:
- Get rid of the Kconfig option for full speed ISO. It may
not be perfect yet, but it hasn't appeared to be dangerous
and pretty much every configuration wants it.
- Instead of two places to disable an empty periodic schedule
after an ISO transfer completes, just have one.
- After the periodic schedule is disabled, we can short-circuit
the schedule scan ... it can't possibly have more work to do.
Assuming a typical config with split iso enabled, the only change
in behavior should be almost unobservable: quicker termination
of periodic scans when the schedule gets emptied.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the EHCI driver, itd->usecs[8] is used in periodic_usecs(), indexed by
uframe. For an ITD's unused uframes it is 0, else it contains the same
value as itd->stream->usecs. To check if an ITD's uframe is used, we can
instead test itd->hw_transaction[uframe]: if used, it will be nonzero no
matter what endianess is used.
This patch replaces those two uses, eliminates itd->usecs[], and saves
eight bytes from each ITD.
Signed-off-by: Karsten Wiese <fzu@wemgehoertderstaat.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dev->sem conforms to mutex style usage. This patch converts it to use
the struct mutex type, and new API.
There is also a small style fix around this comment,
/* unlock here as tower_delete frees dev */
Where I broke the line up to meet the 80 char limit.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds device-tree-aware ehci-ppc-of driver.
The code is based on the ehci-ppc-soc driver by
Stefan Roese <sr@denx.de>.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Stefan Roese <sr@denx.de>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Various small at91_udc cleanups:
- Use generic GPIO calls, not older platform-specific ones
- Use gpio_request()/gpio_free()
- Use VERBOSE_DEBUG convention, not older VERBOSE
- Fix sparse complaint about parameter type (changed to gfp_t)
- Add missing newline to some rarely-seen debug messages
- Fix some old cleanup bugs on probe() fault paths
Also add a mechanism whereby rm9200 gpios can drive the D+ pullup
through an inverting transistor, based on a patch from Steve Birtles.
Most UDC drivers supporting a GPIO based pullup should probably have
such an option, but testing it requries such a board in hand!
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Steve Birtles <arm_kernel_development@micromark.net.cn>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Update the ohci-at91 bus glue to start understanding about the per-port
power switch GPIOs it's given (on the sam9263-ek and potentially other
boards). For the moment this just claims them and forces them active
(assuming active-low power enables) whenever the HCD is loaded.
The assumption is still that board setup configures the GPIOs. Using
gpio_request() tracks actual usage and guards against conflict.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch exports two statistics to userspace:
/sys/bus/usb/device/.../power/connected_duration
/sys/bus/usb/device/.../power/active_duration
connected_duration is the total time (in msec) that the device has
been connected. active_duration is the total time the device has not
been suspended. With these two statistics, tools like PowerTOP can
calculate the percentage time that a device is active, i.e. not
suspended or auto-suspended.
Users can also use the active_duration to check if a device is actually
autosuspended. Currently, they can set power/level to auto and
power/autosuspend to a positive timeout, but there's no way to know from
userspace if a device was actually autosuspended without looking at the
dmesg output. These statistics will be useful in creating an automated
userspace script to test autosuspend for USB devices.
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following improvements were made:
- Fixed control line issue where asserting DTR on ep5 would close ep2
- Added support for calc_num_ports (will help support future composite
devices)
Signed-off-by: Kevin Lloyd <linux@sierrawireless.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
[PATCH] ftdi_sio: add support for more FTDI based JTAG adaptors
There are more devices similar to the Olimex JTAG adaptor, in that the first
port of the FT2232C is used for JTAG, and only the second port is available as
UART.
I have thus renamed ftdi_olimex_{probe,quirk} to ftdi_jtag_{probe,quirk} and
added vendor/product ID's for the OpenMoko Neo1973 Debug Board as well as the
OOCDlink device.
I've also updated the KERN_INFO message sent to userspace to remove the word
'olimex' and an extra '\n' that was causing an empty line in dmesg.
Signed-off-by: Harald Welte <laforge@openmoko.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't pass NULL into termios functions when calling them internally
Remove all the crap which then checks for NULL which can't occur now
Clear CMSPAR as it is not supported
Report the baud rate back to the caller properly (See FIXME someone with
the docs)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove internal NULL passing in termios code
Remove all the if checks it causes
Encode the baud rate back properly
Clear CMSPAR as it is not supported
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove lots of NULL checks that can no longer occur
Encode the baud rate back into the termios (again someone with docs see
FIXME to improve this further)
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a missing dependency which goofs up the xconfig display.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a small glitch noted by Yannick Cote. There is no endpoint number
six, so if a (broken) host wrongly tried to change or read status of
that endpoint, the driver could access reserved register space.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Yannick Cote <yanick@yanos.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Am Sonntag, 16. Dezember 2007 05:23:47 schrieb Andrew Morton:
> On Sat, 15 Dec 2007 07:08:52 -0800 (PST) bugme-daemon@bugzilla.kernel.org wrote:
>
> > http://bugzilla.kernel.org/show_bug.cgi?id=9573
> > There's a null pointer dereference on drivers/usb/serial/whiteheat.c as
> > follows:
> >
> > (1) line 613: the test "if (port->tty)" implies that null is a legal value
> > for "port->tty" at that point
> >
> > (2) neither firm_open nor firm_purge initialize "port->tty"
drivers/usb/serial/usb-serial::serial_open() sets port->tty
The check for NULL is bogus. This patch removes the check.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix potential (never-observed) oops on rare error path,
bugzilla #9594. Fix uses the same test as used earlier.
Also make the adjacent "else" block look like an "else" block
instead of hiding like a bug.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kernel bugzilla entry #9569 reports a potential OOPS in some code
supporting the integrated root hub TT support used on ARC/TDI
derived cores. (This seems to have been a longstanding issue.)
This patch cleans up usage of urb->dev->tt to avoid that potential
oops and also fixes some overly long lines.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some glue bits for the on-chip USB host controller in the Marvell Orion
family of ARM SoCs, which is basically EHCI compatible.
Signed-off-by: Tzachi Perelstein <tzachi@marvell.com>
Reviewed-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
fix warning:
drivers/usb/host/ehci-hcd.c:832:8: warning: symbol 'status' shadows an earlier one
drivers/usb/host/ehci-hcd.c:790:71: originally declared here
Signed-off-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
