Commit Graph

9 Commits

Author SHA1 Message Date
Kay Sievers
fb28ad3590 net: struct device - replace bus_id with dev_name(), dev_set_name()
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-10 13:55:14 -08:00
David S. Miller
babcda74e9 drivers/net: Kill now superfluous ->last_rx stores.
The generic packet receive code takes care of setting
netdev->last_rx when necessary, for the sake of the
bonding ARP monitor.

Drivers need not do it any more.

Some cases had to be skipped over because the drivers
were making use of the ->last_rx value themselves.

Signed-off-by: David S. Miller <davem@davemloft.net>
2008-11-03 21:11:17 -08:00
Johannes Berg
e174961ca1 net: convert print_mac to %pM
This converts pretty much everything to print_mac. There were
a few things that had conflicts which I have just dropped for
now, no harm done.

I've built an allyesconfig with this and looked at the files
that weren't built very carefully, but it's a huge patch.

Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-27 17:06:18 -07:00
Harvey Harrison
b39d66a81f drivers/net: replace __FUNCTION__ with __func__
__FUNCTION__ is gcc-specific, use __func__

Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-09-24 18:59:00 -04:00
David Brownell
c7b7b04206 enc28j60: don't specify (wrong) IRQ type
Recent changes to the IRQ framework have made passing the wrong
trigger type to request_irq() become a fatal error.  In the case
of the enc28j60 driver, it stopped working in my test harness.

(Specifically:  the signal detects "pin change" events, both edges,
not just falling edges.  Similarly, other boards might route it
through an inverter.  Trigger type are board-specific.)

This fixes that problem by the usual fix of expecting board setup
code to have set up the correct IRQ trigger type.  The best known
example of that being x86 setup.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-07-29 18:24:20 -04:00
David Brownell
7dac6f8df6 net/enc28j60: low power mode
Keep enc28j60 chips in low-power mode when they're not in use.
At typically 120 mA, these chips run hot even when idle; this
low power mode cuts that power usage by a factor of around 100.

This version provides a generic routine to poll a register until
its masked value equals some value ... e.g. bit set or cleared.
It's basically what the previous wait_phy_ready() did, but this
version is generalized to support the handshaking needed to
enter and exit low power mode.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17 23:07:29 -04:00
David Brownell
6fd65882f5 net/enc28j60: section fix
Minor bugfixes to the enc28j60 driver ... wrong section marking,
indentation, and bogus use of spi_bus_type.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2008-06-17 23:07:05 -04:00
David Brownell
02ff05c49d net/enc28j60: oops fix
Prevent oops on enc28j60 packet RX:  make sure buffers are aligned.
Not all architectures support unaligned accesses in kernel space.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2008-03-05 18:51:19 -08:00
Claudio Lanconelli
3ec9c11da0 add driver for enc28j60 ethernet chip
Signed-off-by: Claudio Lanconelli <lanconelli.claudio@eptar.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:08:03 -08:00