pxa_gpio_mode() is a universal call that fiddles with the GAFR
(gpio alternate function register.) GAFR does not exist on PXA3
CPUs, but instead the alternate functions are controlled via the
MFP support code.
Platforms are expected to configure the MFP according to their
needs in their platform support code rather than drivers. We
extend this idea to the GAFR, and make the gpio_direction_*()
functions purely operate on the GPIO level.
This means platform support code is entirely responsible for
configuring the GPIOs alternate functions on all PXA CPU types.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make the cpu_is_pxaXXX() macros define to zero when support for a
particular CPU is disabled. This allows us to eliminate code for
CPUs which aren't enabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The PXA DMA support code for smc91x doesn't pass a struct device to
the dma_*map_single() functions, which leads to an oops in the dma
bounce code. We have a struct device which was used to probe the
SMC chip. Use it.
(This patch is slightly larger because it requires struct smc_local
to move into the header file.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure pm callback is called upon initialisation to place port in
correct power saving state. Ensure console is initialised prior
to deciding whether to power down the port.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
a function pxa_init_irq_set_wake() was introduced, so that
processor specific code could install their own version
code setting PFER and PRER registers within pxa_gpio_irq_type
are removed, and the edge configuration is postponed to the
(*set_wake) and copies the GRER and GFER register, which will
always be set up correctly by pxa_gpio_irq_type()
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This definition produces processor specific code in generic function
pxa_gpio_mode(), thus creating inconsistencies for support of pxa25x
and pxa27x in a single zImage.
As David Brownell suggests, make it a run-time variable and initialize
at run-time according to the number of GPIOs on the processor. For now
the initialization happens in pxa_init_irq_gpio(), since there is
already a parameter for that, besides, this is and MUST be earlier
than any subsequent calls to pxa_gpio_mode().
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
since both u-boot and blob support passing MACH_TYPE_LUBBOCK to the
kernel, it should be quite safe to remove this
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Extracted from patch by Eric Miao, this adds the cpu_is_xxx() macros
for identifying PXA3 SoCs.
Signed-off-by: eric miao <eric.y.miao@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Allow the generic clock support code to fiddle with the CKEN register
and mark pxa_set_cken() deprecated.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
get_lcdclk_frequency_10khz() is now redundant, remove it. Hide
pxa27x_get_lcdclk_frequency_10khz() from public view.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename pxa25x and pxa27x memory/lcd/core clock functions, and
select the correct version at run time.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than using the compile-time constant CLOCK_TICK_RATE, select
the clock tick rate at run time. We organise the selection so that
PXA3 automatically falls out with the right tick rate.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The previous implementation was relying on compile time optimizations
based on a constant clock rate. However, support for different PXA
flavors in the same kernel binary requires that the clock be selected at
run time, so here it is.
Let's move this code to a more appropriate location while at it.
Signed-off-by: Nicolas Pitre <npitre@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (408 commits)
[POWERPC] Add memchr() to the bootwrapper
[POWERPC] Implement logging of unhandled signals
[POWERPC] Add legacy serial support for OPB with flattened device tree
[POWERPC] Use 1TB segments
[POWERPC] XilinxFB: Allow fixed framebuffer base address
[POWERPC] XilinxFB: Add support for custom screen resolution
[POWERPC] XilinxFB: Use pdata to pass around framebuffer parameters
[POWERPC] PCI: Add 64-bit physical address support to setup_indirect_pci
[POWERPC] 4xx: Kilauea defconfig file
[POWERPC] 4xx: Kilauea DTS
[POWERPC] 4xx: Add AMCC Kilauea eval board support to platforms/40x
[POWERPC] 4xx: Add AMCC 405EX support to cputable.c
[POWERPC] Adjust TASK_SIZE on ppc32 systems to 3GB that are capable
[POWERPC] Use PAGE_OFFSET to tell if an address is user/kernel in SW TLB handlers
[POWERPC] 85xx: Enable FP emulation in MPC8560 ADS defconfig
[POWERPC] 85xx: Killed <asm/mpc85xx.h>
[POWERPC] 85xx: Add cpm nodes for 8541/8555 CDS
[POWERPC] 85xx: Convert mpc8560ads to the new CPM binding.
[POWERPC] mpc8272ads: Remove muram from the CPM reg property.
[POWERPC] Make clockevents work on PPC601 processors
...
Fixed up conflict in Documentation/powerpc/booting-without-of.txt manually.
* corruption fix: we only want the lower 16 bits of length (0 == 64kb)
* ditto: the upper layer sets max-phys-segments to LIBATA_MAX_PRD,
so we must reset it to own hw-specific length.
* delete unused mv_fill_sg() return value
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
This adds a memchr() implementation to the bootwrapper, which will
be needed when libfdt is merged in.
Signed-off-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Implement show_unhandled_signals sysctl + support to print when a process
is killed due to unhandled signals just as i386 and x86_64 does.
Default to having it off, unlike x86 that defaults on.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently find_legacy_serial_ports() can find no serial ports on the
OPB with flattened device tree. Thus no legacy boot console can be
initialized. Just the early udbg console works, which is initialized
with udbg_init_44x_as1 on the UART's physical address specified in
kernel config. This happens because we look for ns16750 serial
devices only and expect opb node to have a device type property. This
patch makes it look for ns16550-compatible devices and use
of_device_is_compatible() for opb in case device type is not
specified.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the kernel use 1TB segments for all kernel mappings and for
user addresses of 1TB and above, on machines which support them
(currently POWER5+, POWER6 and PA6T).
We detect that the machine supports 1TB segments by looking at the
ibm,processor-segment-sizes property in the device tree.
We don't currently use 1TB segments for user addresses < 1T, since
that would effectively prevent 32-bit processes from using huge pages
unless we also had a way to revert to using 256MB segments. That
would be possible but would involve extra complications (such as
keeping track of which segment size was used when HPTEs were inserted)
and is not addressed here.
Parts of this patch were originally written by Ben Herrenschmidt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Allow a fixed framebuffer address to be assigned to the framebuffer device
instead of allocating the framebuffer from the consistent memory pool.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some custom implementations of the xilinx fb can use resolutions other
than 640x480. This patch allows the resolution to be specified in the
device tree or the xilinx_platform_data structure.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The call to xilinxfb_assign is getting unwieldy when adding features
to the Xilinx framebuffer driver. Change xilinxfb_assign() to accept
a pointer to a xilinxfb_platform_data structure to prepare for adding
additition configuration options.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Add 64-bit physical address support to setup_indirect_pci().
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (867 commits)
[SKY2]: status polling loop (post merge)
[NET]: Fix NAPI completion handling in some drivers.
[TCP]: Limit processing lost_retrans loop to work-to-do cases
[TCP]: Fix lost_retrans loop vs fastpath problems
[TCP]: No need to re-count fackets_out/sacked_out at RTO
[TCP]: Extract tcp_match_queue_to_sack from sacktag code
[TCP]: Kill almost unused variable pcount from sacktag
[TCP]: Fix mark_head_lost to ignore R-bit when trying to mark L
[TCP]: Add bytes_acked (ABC) clearing to FRTO too
[IPv6]: Update setsockopt(IPV6_MULTICAST_IF) to support RFC 3493, try2
[NETFILTER]: x_tables: add missing ip6t_modulename aliases
[NETFILTER]: nf_conntrack_tcp: fix connection reopening
[QETH]: fix qeth_main.c
[NETLINK]: fib_frontend build fixes
[IPv6]: Export userland ND options through netlink (RDNSS support)
[9P]: build fix with !CONFIG_SYSCTL
[NET]: Fix dev_put() and dev_hold() comments
[NET]: make netlink user -> kernel interface synchronious
[NET]: unify netlink kernel socket recognition
[NET]: cleanup 3rd argument in netlink_sendskb
...
Fix up conflicts manually in Documentation/feature-removal-schedule.txt
and my new least favourite crap, the "mod_devicetable" support in the
files include/linux/mod_devicetable.h and scripts/mod/file2alias.c.
(The latter files seem to be explicitly _designed_ to get conflicts when
different subsystems work with them - that have an absolutely horrid
lack of subsystem separation!)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (80 commits)
[MIPS] tlbex.c: Cleanup __init usage.
[MIPS] WRPPMC serial support move to platform device
[MIPS] R1: Fix hazard barriers to make kernels work on R2 also.
[MIPS] VPE: reimplement ELF loader.
[MIPS] cleanup WRPPMC include files
[MIPS] Add BUG_ON assertion for attempt to run kernel on the wrong CPU type.
[MIPS] SMP: Use ISO C struct initializer for local structs.
[MIPS] SMP: Kill useless casts.
[MIPS] Kill num_online_cpus() loops.
[MIPS] SMP: Implement smp_call_function_mask().
[MIPS] Make facility to convert CPU types to strings generally available.
[MIPS] Convert list of CPU types from #define to enum.
[MIPS] Optimize get_unaligned / put_unaligned implementations.
[MIPS] checkfiles: Fix "need space after that ','" errors.
[MIPS] Fix "no space between function name and open parenthesis" warnings.
[MIPS] Allow hardwiring of the CPU type to a single type for optimization.
[MIPS] tlbex: Size optimize code by declaring a few functions inline.
[MIPS] pg-r4k.c: Dump the generated code
[MIPS] Cobalt: Remove cobalt_machine_power_off()
[MIPS] Cobalt: Move reset port definition to arch/mips/cobalt/reset.c
...
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: (24 commits)
ide: use only ->set_pio_mode method for programming PIO modes (take 2)
sis5513: don't change UDMA settings when programming PIO
it8213/piix/slc90e66: don't change DMA settings when programming PIO
alim15x3: PIO mode setup fixes
siimage: fix ->set_pio_mode method to select PIO data transfer
cs5520: don't enable VDMA in ->speedproc
sc1200: remove redundant warning message from sc1200_tune_chipset()
ide-pmac: PIO mode setup fixes (take 3)
icside: fix ->speedproc to return on unsupported modes (take 5)
sgiioc4: use ide_tune_dma()
amd74xx/via82cxxx: use ide_tune_dma()
ide: add ide_set{_max}_pio() (take 4)
ide: Kconfig face-lift
ide: move ide_rate_filter() calls to the upper layer (take 2)
sis5513: add ->udma_filter method for chipset_family >= ATA_133
ide: mode limiting fixes for user requested speed changes
ide: add missing ide_rate_filter() calls to ->speedproc()-s
ide: call udma_filter() before resorting to the UltraDMA mask
ide: make jmicron match vendor and device class
pdc202xx_new: switch to using pci_get_slot() (take 2)
...
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-leds:
leds: Update Cobalt Qube series front LED support
leds: Add Cobalt Raq series LEDs support
leds: Rename leds-cobalt driver
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Convert corgi backlight driver into a more generic driver
backlight: Add Samsung LTV350QV LCD driver
backlight: Fix cr_bllcd allocations and error paths
backlight/leds: Make two structs static
* 'block-2.6.24' of git://git.kernel.dk/data/git/linux-2.6-block: (37 commits)
[BLOCK] Fix failing compile with BLK_DEV_IO_TRACE=n
compat_ioctl: move floppy handlers to block/compat_ioctl.c
compat_ioctl: move cdrom handlers to block/compat_ioctl.c
compat_ioctl: move BLKPG handling to block/compat_ioctl.c
compat_ioctl: move hdio calls to block/compat_ioctl.c
compat_ioctl: handle blk_trace ioctls
compat_ioctl: add compat_blkdev_driver_ioctl()
compat_ioctl: move common block ioctls to compat_blkdev_ioctl
Sysace: Don't enable IRQ until after interrupt handler is registered
Sysace: sparse fixes
Sysace: Minor coding convention fixup
drivers/block/umem: use DRIVER_NAME where appropriate
drivers/block/umem: trim trailing whitespace
drivers/block/umem: minor cleanups
drivers/block/umem: use dev_printk()
drivers/block/umem: move private include away from include/linux
Sysace: Labels in C code should not be indented.
Sysace: Add of_platform_bus binding
Sysace: Move IRQ handler registration to occur after FSM is initialized
Sysace: minor rework and cleanup changes
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/avr32-2.6:
[AVR32] Fix random segfault with preemption
[AVR32] Don't use __builtin_xchg()
[AVR32] ngw100 i2c-gpio tweaks
[AVR32] Ignore a few irrelevant syscalls
[AVR32] SMC configuration in clock cycles
[AVR32] Drop support for redundant "keepinitrd" boot-time parm.
[AVR32] Make dma_sync_*_for_cpu no-ops
[AVR32] Remove unneeded 8K alignment of .text section
[AVR32] Kill a few hardcoded constants in vmlinux.lds
[AVR32] rename vmlinux.lds
[AVR32] fix command line parsing in early_parse_fbmem
[AVR32] checkstack support
[AVR32] Wire up USBA device
[AVR32] add multidrive support for pio driver
[AVR32] /sys/kernel/debug/at32ap_clk
[AVR32] Move AT32_PM_BASE definition into pm.h
