Software events are required as part of the measurable stuff by the
Linux performance counter subsystem. Here is the list of events added by
this patch:
PERF_COUNT_SW_PAGE_FAULTS
PERF_COUNT_SW_PAGE_FAULTS_MIN
PERF_COUNT_SW_PAGE_FAULTS_MAJ
PERF_COUNT_SW_ALIGNMENT_FAULTS
PERF_COUNT_SW_EMULATION_FAULTS
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@gmail.com>
To: linux-mips@linux-mips.org
Cc: a.p.zijlstra@chello.nl
Cc: paulus@samba.org
Cc: mingo@elte.hu
Cc: acme@redhat.com
Cc: jamie.iles@picochip.com
Acked-by: David Daney <ddaney@caviumnetworks.com>
Reviewed-by: Matt Fleming <matt@console-pimps.org>
Patchwork: https://patchwork.linux-mips.org/patch/1686/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for Titan TNETV1050,1055,1056,1060 variants. This SoC is almost
completely identical to AR7 except on a few points:
- a second bank of gpios is available
- vlynq0 on titan is vlynq1 on ar7
- different PHY addresses for cpmac0
This SoC can be found on commercial products like the Linksys WRTP54G
Original patch by Xin with improvments by Florian.
Signed-off-by: Xin Zhen <xlonestar2000@aim.com>
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1563/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
In order to detect the Titan variant, we must initialize GPIOs earlier since
detection relies on some GPIO values to be set.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/1562/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
The OCTEON II SOC has USB EHCI and OHCI controllers connected directly
to the internal I/O bus. This patch adds the necessary 'glue' logic
to allow ehci-hcd and ohci-hcd drivers to work on OCTEON II.
The OCTEON normally runs big-endian, and the ehci/ohci internal
registers have host endianness, so we need to select
USB_EHCI_BIG_ENDIAN_MMIO.
The ehci and ohci blocks share a common clocking and PHY
infrastructure. Initialization of the host controller and PHY clocks
is common between the two and is factored out into the
octeon2-common.c file.
Setting of USB_ARCH_HAS_OHCI and USB_ARCH_HAS_EHCI is done in
arch/mips/Kconfig in a following patch.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1675/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The EHCI and OHCI blocks connection to the I/O bus is controlled by
these registers.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-usb@vger.kernel.org
To: dbrownell@users.sourceforge.net
Patchwork: http://patchwork.linux-mips.org/patch/1674/
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
create mode 100644 arch/mips/include/asm/octeon/cvmx-uctlx-defs.h
The CN63XXP1 needs a couple of workarounds to ensure memory is not written
in unexpected ways.
All PREF with hints in the range 0-4,6-24 are replaced with PREF 28. We
pass a flag to the assembler to cover compiler generated code, and patch
uasm for the dynamically generated code.
The write buffer threshold is reduced to 4.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1672/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The creation of the I/O clock domain requires some adjustments. Since
the watchdog counters are clocked by the I/O clock, use its rate for
timing calculations.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-watchdog@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1659/
Acked-by: Wim Van Sebroeck <wim@iguana.be>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The creation of the I/O clock domain requires some adjustments. Since the
CF bus timing logic is clocked by the I/O clock, use its rate for delay
calculations.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: linux-ide@vger.kernel.org
Patchwork: http://patchwork.linux-mips.org/patch/1660/
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The I2C and UARTS are clocked by the I/O clock, use its rate for these
devices.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1670/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Starting with cn63xx Octeon I/O blocks are clocked at a different rate
than the CPU. Add a new function octeon_get_io_clock_rate() that
yields the I/O clock rate.
Also rearrange octeon_get_clock_rate() to get the value from the saved
sysinfo structure.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1671/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We can run with any simulator clock rate. Get rid of the code
overriding it to 6MHz.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1669/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The per-CPU clocks are synchronized from IPD_CLK_COUNT, on cn63XX it must
be scaled by the clock frequency ratio.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1667/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The OCTEON II ISA extends the original OCTEON ISA, so give it its own
__elf_platform string so optimized libraries can be selected in
userspace.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1665/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CN63XX has a different L2 cache architecture. Update the helper
functions to reflect this.
Some joining of split lines was also done to improve readability, as
well as reformatting of comments.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1663/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CN63XX is a new 6-CPU SOC based on the new OCTEON II CPU cores.
Join some lines back together. This makes some of them exceed 80
columns, but they are uninteresting and this unclutters things.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1668/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
All Octeon chips can support more than 4GB of RAM. Also due to how Octeon
PCI is setup, even some configurations with less than 4GB of RAM will have
portions that are not accessible from 32-bit devices.
Enable the swiotlb code to handle the cases where a device cannot directly
do DMA. This is a complete rewrite of the Octeon DMA mapping code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows platforms that are using the swiotlb to initialize it.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1638/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use asm-generic/dma-mapping-common.h to handle all DMA mapping operations
and establish a default get_dma_ops() that forwards all operations to the
existing code.
Augment dev_archdata to carry a pointer to the struct dma_map_ops, allowing
DMA operations to be overridden on a per device basis. Currently this is
never filled in, so the default dma_map_ops are used. A follow-on patch
sets this for Octeon PCI devices.
Also initialize the dma_debug system as it is now used if it is configured.
Includes fixes by Kevin Cernekee <cernekee@gmail.com>.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1637/
Patchwork: http://patchwork.linux-mips.org/patch/1678/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Any function defined in a header file should be inline. This helps us
avoid 'unused' compiler warnings when we include the files in more
places in subsequent patches.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1636/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Give us a nice place to allocate coherent DMA memory for 32-bit devices.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1635/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On OCTEON, we reserve the last 256MB of 32-bit PCI address space, mapping
the RAM in this region at a high DMA address. This makes memory in this
region unavailable for 32-bit DMA.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1634/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
DMA mapping may reduce the usable physical address range usable for
32-bit DMA.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1633/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This allows follow-on patches to dma mapping functions to work with
the octeon mgmt device..
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1632/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was a nice optimization - on paper at least. In practice it results in
branches that may exceed the maximum legal range for a branch. We can
fight that problem with -ffunction-sections but -ffunction-sections again
is incompatible with -pg used by the function tracer.
By rewriting the loop around all simple LL/SC blocks to C we reduce the
amount of inline assembler and at the same time allow GCC to often fill
the branch delay slots with something sensible or whatever else clever
optimization it may have up in its sleeve.
With this optimization gone we also no longer need -ffunction-sections,
so drop it.
This optimization was originally introduced in 2.6.21, commit
5999eca25c1fd4b9b9aca7833b04d10fe4bc877d (linux-mips.org) rsp.
f65e4fa8e0 (kernel.org).
Original fix for the issues which caused me to pull this optimization by
Paul Gortmaker <paul.gortmaker@windriver.com>.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/sfrench/cifs-2.6:
cifs: Cleanup and thus reduce smb session structure and fields used during authentication
NTLM auth and sign - Use appropriate server challenge
cifs: add kfree() on error path
NTLM auth and sign - minor error corrections and cleanup
NTLM auth and sign - Use kernel crypto apis to calculate hashes and smb signatures
NTLM auth and sign - Define crypto hash functions and create and send keys needed for key exchange
cifs: cifs_convert_address() returns zero on error
NTLM auth and sign - Allocate session key/client response dynamically
cifs: update comments - [s/GlobalSMBSesLock/cifs_file_list_lock/g]
cifs: eliminate cifsInodeInfo->write_behind_rc (try #6)
[CIFS] Fix checkpatch warnings and bump cifs version number
cifs: wait for writeback to complete in cifs_flush
cifs: convert cifsFileInfo->count to non-atomic counter
We used to protect against overflow, but rather than return an error, do
what read/write does, namely to limit the total size to MAX_RW_COUNT.
This is not only more consistent, but it also means that any broken
low-level read/write routine that still keeps counts in 'int' can't
break.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 338e4fab added a missing kfree if the alloc_pci_dev failed
but forgot to include <linux/slab.h> for the definition of
kfree.
Signed-off-by: Kyle McMartin <kyle@redhat.com>
Always use a safe 5-byte noop sequence. Drop the trap test, since it
is known to return false negatives on some virtualization platforms on
32 bits. The resulting code is both simpler and safer.
Cc: Daniel Drake <dsd@laptop.org>
Cc: Jason Baron <jbaron@redhat.com>
Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The following are the fixes in this patch:
1. Added support of set timestamp command in the driver
2. Pass all status code to mgmt application. Earlier we were passing
only failed ones.
3. Call class_destroy after unregister_chrdev and pci_unregister_driver
Signed-off-by: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
The vmlinux.lds.h knobs to emit the __jump_table section in the main
kernel image takes care to align the section, but this doesn't help
for the __jump_table section that gets emitted into modules.
Fix the resulting lack of section alignment by explicitly specifying
it in the assembler.
Signed-off-by: David S. Miller <davem@davemloft.net>
LKML-Reference: <20101023.110624.226758370.davem@davemloft.net>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Some archs do not need to do anything special for jump labels on
startup (like MIPS). This patch adds a weak function stub for
arch_jump_label_text_poke_early();
Cc: Jason Baron <jbaron@redhat.com>
Cc: David Miller <davem@davemloft.net>
Cc: David Daney <ddaney@caviumnetworks.com>
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <1286218615-24011-2-git-send-email-ddaney@caviumnetworks.com>
LKML-Reference: <20101015201037.703989993@goodmis.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Kprobes and jump label were having a race between mutexes that
was fixed by reordering the jump label. But this reordering
moved the jump label mutex into a preempt disable location.
This patch does a little fiddling to move the grabbing of
the jump label mutex from inside the preempt disable section
and still keep the order correct between the mutex and the
kprobes lock.
Reported-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Jason Baron <jbaron@redhat.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'for-linus' of git://git390.marist.edu/pub/scm/linux-2.6:
[S390] fix kprobes single stepping
[S390] tape: fix dbf usage
[S390] dasd: provide a Sense Path Group ID ioctl
[S390] ftrace: select HAVE_C_RECORDMCOUNT
[S390] vdso: get rid of redefinition warnings
[S390] facility detection: remove unused variable
[S390] hypfs: Fix error handling in hypfs_diag initialization
[S390] topology: fix cpu masks for topology=off case
[S390] topology: add SCHED_MC config option
[S390] Kconfig: add machine type number to code generation options
[S390] Add z196 machine type to setup_hwcaps
* 'for-linus' of git://neil.brown.name/md:
md: tidy up device searches in read_balance.
md/raid1: fix some typos in comments.
md/raid1: discard unused variable.
md: unplug writes to external bitmaps.
md: use separate bio pool for each md device.
md: change type of first arg to sync_page_io.
md/raid1: perform mem allocation before disabling writes during resync.
md: use bio_kmalloc rather than bio_alloc when failure is acceptable.
md: Fix possible deadlock with multiple mempool allocations.
md: fix and update workqueue usage
md: use sector_t in bitmap_get_counter
md: remove md_mutex locking.
md: Fix regression with raid1 arrays without persistent metadata.
This patch adds a new mount parameter 'ecryptfs_mount_auth_tok_only' to
force ecryptfs to use only authentication tokens which signature has
been specified at mount time with parameters 'ecryptfs_sig' and
'ecryptfs_fnek_sig'. In this way, after disabling the passthrough and
the encrypted view modes, it's possible to make available to users only
files encrypted with the specified authentication token.
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: James Morris <jmorris@namei.org>
[Tyler: Clean up coding style errors found by checkpatch]
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
This patch replaces the check of the 'matching_auth_tok' pointer with
the exit status of ecryptfs_find_auth_tok_for_sig().
This avoids to use authentication tokens obtained through the function
ecryptfs_keyring_auth_tok_for_sig which are not valid.
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: James Morris <jmorris@namei.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
This patch allows keys requested in the function
ecryptfs_keyring_auth_tok_for_sig()to be released when they are no
longer required. In particular keys are directly released in the same
function if the obtained authentication token is not valid.
Further, a new function parameter 'auth_tok_key' has been added to
ecryptfs_find_auth_tok_for_sig() in order to provide callers the key
pointer to be passed to key_put().
Signed-off-by: Roberto Sassu <roberto.sassu@polito.it>
Cc: Dustin Kirkland <kirkland@canonical.com>
Cc: James Morris <jmorris@namei.org>
[Tyler: Initialize auth_tok_key to NULL in ecryptfs_parse_packet_set]
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
eCryptfs was passing the LOOKUP_OPEN flag through to the lower file
system, even though ecryptfs_create() doesn't support the flag. A valid
filp for the lower filesystem could be returned in the nameidata if the
lower file system's create() function supported LOOKUP_OPEN, possibly
resulting in unencrypted writes to the lower file.
However, this is only a potential problem in filesystems (FUSE, NFS,
CIFS, CEPH, 9p) that eCryptfs isn't known to support today.
https://bugs.launchpad.net/ecryptfs/+bug/641703
Reported-by: Kevin Buhr
Cc: stable <stable@kernel.org>
Signed-off-by: Tyler Hicks <tyhicks@linux.vnet.ibm.com>
