This patch fixes power LED blinking and power-off on DNS-323 rev. B1.
GPIO pin 3 has to be set to 1 to stop power LED blinking and to allow the LED to be controlled via leds-gpio. This pin has to be also set to 1 for power-off to work.
To power-off the rev. B1 machine, pin 8 has to be set to 1 and then set to 0 to do actual power-off.
Tested on my DNS-323 rev. B1
Signed-off-by: Erik Benada <erikbenada@yahoo.ca>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
CONFIG_X86_CPU_DEBUG, which provides some parsed versions of the x86
CPU configuration via debugfs, has caused boot failures on real
hardware. The value of this feature has been marginal at best, as all
this information is already available to userspace via generic
interfaces.
Causes crashes that have not been fixed + minimal utility -> remove.
See the referenced LKML thread for more information.
Reported-by: Ozan Çağlayan <ozan@pardus.org.tr>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
LKML-Reference: <alpine.LFD.2.00.1001221755320.13231@localhost.localdomain>
Cc: Jaswinder Singh Rajput <jaswinder@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: <stable@kernel.org>
Commit d1c84f79a6
leads to a regression when microcode_amd.c is compiled into the kernel.
It causes a big boot delay because the firmware is not available.
See http://marc.info/?l=linux-kernel&m=126267290920060
It also renders the reload sysfs attribute useless.
Fixing this is too intrusive for an -rc5 kernel.
Thus I'd like to restore the microcode loading behaviour of kernel
2.6.32.
CC: Gene Heskett <gene.heskett@verizon.net>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
LKML-Reference: <20100122203456.GB13792@alberich.amd.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
HPET MSI on platforms with ATI SB700/SB800 as they seem to have some
side-effects on floppy DMA. Do not use HPET MSI on such platforms.
Original problem report from Mark Hounschell
http://lkml.indiana.edu/hypermail/linux/kernel/0912.2/01118.html
[ This patch needs to go to stable as well. But, there are some
conflicts that prevents the patch from going as is. I can
rebase/resubmit to stable once the patch goes upstream.
hpa: still Cc:'ing stable@ as an FYI. ]
Tested-by: Mark Hounschell <markh@compro.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: <stable@kernel.org>
LKML-Reference: <20100121190952.GA32523@linux-os.sc.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
nodes_possible_map does not currently include nodes that have SRAT
entries that are all ACPI_SRAT_MEM_HOT_PLUGGABLE since the bit is
cleared in nodes_parsed if it does not have an online address range.
Unequivocally setting the bit in nodes_parsed is insufficient since
existing code, such as acpi_get_nodes(), assumes all nodes in the map
have online address ranges. In fact, all code using nodes_parsed
assumes such nodes represent an address range of online memory.
nodes_possible_map is created by unioning nodes_parsed and
cpu_nodes_parsed; the former represents nodes with online memory and
the latter represents memoryless nodes. We now set the bit for
hotpluggable nodes in cpu_nodes_parsed so that it also gets set in
nodes_possible_map.
[ hpa: Haicheng Li points out that this makes the naming of the
variable cpu_nodes_parsed somewhat counterintuitive. However, leave
it as is in the interest of keeping the pure bug fix patch small. ]
Signed-off-by: David Rientjes <rientjes@google.com>
Tested-by: Haicheng Li <haicheng.li@linux.intel.com>
LKML-Reference: <alpine.DEB.2.00.1001201152040.30528@chino.kir.corp.google.com>
Cc: <stable@kernel.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Deassigning a device from the passthrough domain does not
work and breaks device assignment to kvm guests. This patch
fixes the issue.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
This patch moves the initialization of the iommu-api out of
the dma-ops initialization code. This ensures that the
iommu-api is initialized even with iommu=pt.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
In the __detach_device function the reference count for a
device-domain binding may become zero. This results in the
device being removed from the domain and dev_data->domain
will be NULL. This is bad because this pointer is
dereferenced when trying to unlock the domain->lock. This
patch fixes the issue by keeping the domain in a seperate
variable.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
The variable i in this function could be increased to over
2**32 which would result in an integer overflow when using
int. Fix it by changing i to unsigned long.
Cc: stable@kernel.org
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
OMAP GP timers keep running for a few cycles after they are stopped,
which can cause the timer to expire and generate an interrupt. The
pending interrupt will prevent e.g. OMAP from entering suspend, thus
we ack it manually. Only applicable on OMAP2/3/4.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Commit cfc38999f (backlight: Pass device through notify callback)
added a struct device argument to the notify callback, but didn't
update the user of it in mach-hmt.c
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf: x86: Add support for the ANY bit
perf: Change the is_software_event() definition
perf: Honour event state for aux stream data
perf: Fix perf_event_do_pending() fallback callsite
perf kmem: Print usage help for unknown commands
perf kmem: Increase "Hit" column length
hw-breakpoints, perf: Fix broken mmiotrace due to dr6 by reference change
perf timechart: Use tid not pid for COMM change
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (23 commits)
ACPI: delete acpi_processor_power_verify_c2()
ACPI: allow C3 > 1000usec
ACPI: enable C2 and Turbo-mode on Nehalem notebooks on A/C
ACPI: power_meter: remove double kfree()
ACPI: processor: restrict early _PDC to opt-in platforms
ACPI: Fix unused variable warning in sbs.c
acpi: make ACPI device id constant
sony-laptop - fix using of uninitialized variable
ACPI: Fix section mismatch error for acpi_early_processor_set_pdc()
eeepc-laptop: disable wireless hotplug for 1201N
eeepc-laptop: add hotplug_disable parameter
eeepc-laptop: switch to using sparse keymap library
eeepc-laptop: dmi blacklist to disable pci hotplug code
eeepc-laptop: disable cpu speed control on EeePC 701
ACPI: don't cond_resched if irq is disabled
ACPI: Remove unnecessary cast.
ACPI: Advertise to BIOS in _OSC: _OST on _PPC changes
ACPI: EC: Add wait for irq storm
ACPI: SBS: Move SBS HC callback to faster Notify queue
x86, ACPI: delete acpi_boot_table_init() return value
...
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: 5888/1: arm: Update comments in cacheflush.h and remove unnecessary V6 and V7 comments
ARM: 5886/1: arm: Fix cpu_proc_fin() for proc-v7.S and make kexec work
ARM: 5885/1: arm: Flush TLB entries in setup_mm_for_reboot()
ARM: 5884/1: arm: Fix DCC console for v7
ARM: 5883/1: Revert "disable NX support for OABI-supporting kernels"
ARM: 5882/1: ARM: Fix uncompress code compile for different defines of flush(void)
ARM: fix badly placed mach/plat entries in Kconfig & Makefile
To distinguish between mx31lite and mx31lilly boards better to use
different enum types.
Signed-off-by: Vladimir Zapolskiy <vzapolskiy@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Propagate the ANY bit into the fixed counter config for v3 and higher.
Signed-off-by: Stephane Eranian <eranian@google.com>
[a.p.zijlstra@chello.nl: split from larger patch]
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4b5430c6.0f975e0a.1bf9.ffff85fe@mx.google.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
As noted by Benjamin Herrenschmidt, the generic IRQ layer
only sets irq_desc[irq].affinity after ->set_affinity()
succeeds.
So we have to use the passed in cpumask.
Signed-off-by: David S. Miller <davem@davemloft.net>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warning when CONFIG_DEBUG_FS wasn't selected:
arch/arm/mach-omap2/pm-debug.c:57: warning: 'pm_dbg_init' declared 'static' but never defined
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Currently, DSS does not wakeup when there is a DMA request. DSS wake
up event must be enabled so that the DMA request to refill the FIFO
will wake up the CORE domain.
Signed-off-by: Subramani Venkatesh <subramani.venkatesh@windriver.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
During suspend, the kernel timekeeping subsystem is shut down. Before
suspend and upon resume, it uses a weak function
read_persistent_clock() to determine the amount of time that elapsed
during suspend.
This function was not implemented on OMAP, so from the timekeeping
subsystem perspective (and thus userspace as well) it appeared that no
time elapsed during suspend.
This patch uses the 32k sync timer as a the persistent clock.
NOTE: This does *NOT* fully handle wrapping of the 32k sync timer, so
more than one wrapping of the 32k sync timer during suspend may
cause problems. Also note there are not interrupts when the 32k
sync timer wraps, so something else has to be done.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Due to OMAP3 erratas 1.157, 1.185 the save of the last pad register
(ETK_D14 and ETK_D15) can fail sometimes when there is simultaneous
OCP access to the SCM register area. Fixed by writing the last
register to the save area.
Also, optimized the delay loop for the HW save to include an udelay(1),
which limits the number of unnecessary HW accesses to SCM register area
during the save.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
val is an u64 pointer, we need an int to check the error.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Wake-up from McBSP ports are needed, especially when the THRESHOLD
dma mode is in use for audio playback.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
The PM debug code fails to build on when CONFIG_DEBUG_FS is not
enabled.
Build error log:
arch/arm/mach-omap2/built-in.o: In function `omap_sram_idle':
arch/arm/mach-omap2/pm34xx.c:449: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/pm34xx.c:460: undefined reference to `pm_dbg_regset_save'
arch/arm/mach-omap2/built-in.o: In function `configure_vc':
arch/arm/mach-omap2/pm34xx.c:1237: undefined reference to `pm_dbg_regset_init'
arch/arm/mach-omap2/pm34xx.c:1238: undefined reference to `pm_dbg_regset_init'
make: *** [.tmp_vmlinux1] Error 1
This patch fixes the above errors.
Kernel booting is tested on omap zoom2 and zoom3 boards.
Signed-off-by: Manjunatha GK <manjugk@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
As part of Core domain context restoration while coming out of off mode
there are some registers being restored which are not required to be restored.
ROM code will have restored them already. Overwriting some of them can have
potential side effect. Eg: CM_CLKEN_PLL register should not be written while dpll is locked.
Tested on OMAP 3430 SDP for suspend/resume and off mode with sleep_while_idle enabled.
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Current value is stored on SDRAM and it is written back during wakeup.
Previously a static value of 0x72 was written there.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Thara Gopinath <thara@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Previously used u32 as temporary data storage that wraps around at 4.294s.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
This patch removes code blocks that are repeated
in function prcm_setup_regs().
Signed-off-by: Sanjeev Premi <premi@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
OMAP interrupt controller goes to unknown state when there is right
combination of l3,l4 sleep/wake-up transitions, l4 autoidle in
interrupt controller and some interrupt. When this happens, interrupts
are not delivered to ARM anymore and ARM will remain in WFI (wait for
interrupt) until interrupt controller is forced to wake-up
(i.e. lauterbach).
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Enable the auto-idle feature of the SCM block to save some additional
power.
Signed-off-by: Mika Westerberg <ext-mika.1.westerberg@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Suspending drivers may still generate interrupts just before their suspend is
completed. Any pending interrupts here will prevent sleep.
Signed-off-by: Tero Kristo <tero.kristo@nokia.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Don't assume that gpmc_l3_clk is on, enable it before touching
configuration registers.
Note that the current code assumes that this clock is always
enabled. We are already setting smart idle and L3 autogating
for GPMC clock in gpmc_init.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add the rest of the conflict detection and resolution logic necessary
to support more than one counter at a time on sparc64.
The structure and implementation closely mimicks that of powerpc.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pretty straightforward, and it should be easy to add accurate
walk through of signal stack frames in userspace.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tested-by: Jens Axboe <jens.axboe@oracle.com>
Commit 52650505fb caused clock initialization
to fail on OMAP1 with "BUG: spinlock lockup on CPU#0" -- this is because
omap1_select_table_rate() and omap1_round_to_table_rate() call clk_get_rate()
with the clockfw spinlock held. Fix by accessing the rate directly from
the internal clock framework functions.
Thanks to Tony Lindgren <tony@atomide.com> for reporting and testing the fix.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Tony Lindgren <tony@atomide.com>
For all DPLL's the valid dividers are same as the values
to be programmed in the register. 0 is an invalid value.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The CHIRONSS has its own local PRCM module and the register defines
need to use the CHIRONSS base and not the PRM base.
The changes are generated by updating the script which autogenerates
the file modifed in the patch.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We need to set the omap_chip.oc carefully for the clocks to work.
To fix this, set the omap_chip.oc in omap3_check_features() based
on the CONTROL_IDCODE and silicon revision registers.
Also add handling for 34xx es3.1.2 as es3.1 for now.
Fixes booting on at least overo board.
Based on an earlier patch by Paul Walmsley <paul@pwsan.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make the omap_mux_read and write available for board code,
and rename omap_mux_set_board_signals into omap_mux_write_array.
Also add the related prototypes and comments into mux.h.
In some cases we want to change the signals dynamically,
mostly for power management.
Note that we cannot use the signal names as they are set
__init to save memory.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like cmdline muxing got broken at some point when we
decided to limit muxing to __init code. Currently omap_mux_entry
list is not yet initialized when we try to initialize cmdline
muxing.
Fix this by calling omap_mux_init_list() before calling
omap_mux_set_cmdline_signals().
Reported-by: Philip Balister <philip@balister.org>
Tested-by: Philip Balister <philip@balister.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The first thing that omap2_init_clksel_parent() does is check for
a non-zero .clksel field in the struct clk. Therefore, it is
pointless calling this function on clocks where the clksel field
is unset.
Remove init calls to omap2_init_clksel_parent() on clocks without
a clksel field.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the current implementation the sysconfig value is read into
_sysc_cache once and an actual update to the sysconfig register
happens only if the new value paased is differnt from the one in _sysc_cache.
_sysc_cache is updated only if _HWMOD_SYSCONFIG_LOADED is not set.
This can lead to the follwing issue if off mode is enabled in modules
which employs "always-retore" mechanism of context save and restore.
a. The module sets the sysconfig register through omap_device_enable.
Here _sysc_cache is updated with the value written to the sysconfig
register and left.
b. The power domain containig the module enters off mode and the
module context is lost.
c. The module in use becomes active and calls omap_device_enable to
enable itself. Here a read of sysconfig register does not happen
as _HWMOD_SYSCONFIG_LOADED flag is set. The value to be written
to the sysconfig register will be same as the one written in step a.
Since _sysc_cache reflects the previous written value an update
of the sysconfig register does not happen.
This means in modules which employs "always-restore" mechanism
after off , the sysconfig regsiters will never get updated.
This patch introduces a flag SYSC_NO_CACHE which if set ensures that the
sysconfig register is always read into _sysc_cache before an update is
attempted.
This flags need to be set only by modules which does not do a context save
but re-initializes the registers every time the module is accessed. This
includes modules like i2c, smartreflex etc.
Signed-off-by: Thara Gopinath <thara@ti.com>
[paul@pwsan.com: tweaked to apply on a different head, added flag comment]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The comments in cacheflush.h should follow what's in
struct cpu_cache_fns. The comments for V6 and V7 are
unnecessary.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The comments in arm_machine_restart() suggest that cpu_proc_fin()
will clean and disable cache and turn off interrupts. This does
not seem to be implemented for proc-v7.S, implement it the same
way as for proc-v6.S.
This also makes kexec work for v7. Note that a related TLB and
branch traget flush patch is also needed to avoid kexec
"crc error".
Note that there are still some issues that seem to be related
to L2 cache being on and causing occasional uncompress "crc error"
with kexec. Anyways, this gets kexec mostly working on V7 for now.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We need to do that if we tinker with the MMU entries.
This fixes the occasional bug with kexec where the new
fails to uncompress with "crc error". Most likely at
least kexec on v6 and v7 need this fix.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Without this patch arch/arm/compressed/head.S defaults to generic
DCC code that does not work for v7.
For more information on the v7 DCC, see Cortex-A8 TRM
"12.11.1 Debug communications channel".
To use it with post 2.6.33-rc1 or later, you need to have:
CONFIG_DEBUG_LL=y
ONFIG_DEBUG_ICEDCC=y
CONFIG_EARLY_PRINTK=y
Earlier kernels need commit 93fd03a8c6
backported.
Tested on omap3430.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
sh64 on the other hand provides both direct broken out syscalls as well
as socketcall access. As there are binaries that use both socketcall has
to stay around. The current ABI prefers direct syscalls.
It was pointed out that when sys_recvmmsg was added in, sys_accept4 was
overlooked. This takes care of wiring it up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
sh32 at the moment only uses sys_socketcall to reach these, so unwire
recvmmsg for now. While we're at it, add it to the ignore list, as per
the s390 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We can use logical flat mode if there are <= 8 logical cpu's
(irrespective of physical apic id values). This will enable simplified
and efficient IPI and device interrupt routing on such platforms.
This has been tested to work on both Intel and AMD platforms.
Exceptions like IBM summit platform which can't use logical flat mode
are addressed by using OEM platform checks.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Chris McDermott from IBM confirmed that hurricane chipset in IBM summit
platforms doesn't support logical flat mode. Irrespective of the other
things like apic_id's, total number of logical cpu's, Linux kernel
should default to physical mode for this system.
The 32-bit kernel does so using the OEM checks for the IBM summit
platform. Add a similar OEM platform check for the 64bit kernel too.
Otherwise the linux kernel boot can hang on this platform under certain
bios/platform settings.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Chris McDermott <lcm@linux.vnet.ibm.com>
Cc: Yinghai Lu <yinghai@kernel.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Move cpu hotplug driver lock from pseries to powerpc
powerpc: Move /proc/ppc64 to /proc/powerpc update
powerpc/8xx: Fix user space TLB walk in dcbX fixup
powerpc: Fix decrementer setup on 1GHz boards
powerpc/iseries: Initialise on-stack completion
powerpc/hvc: Driver build breaks with !HVC_CONSOLE
serial/pmac_zilog: Workaround problem due to interrupt on closed port
powerpc/macintosh: Make Open Firmware device id constant
powerpc: Use helpers for rlimits
powerpc: cpumask_of_node() should handle -1 as a node
powerpc/pseries: Fix dlpar compile warning without CONFIG_PROC_DEVICETREE
powerpc/pseries: Fix xics interrupt affinity
powerpc/swsusp_32: Fix TLB invalidation
powerpc/8xx: Always pin kernel instruction TLB
powerpc: 2.6.33 update of defconfigs for embedded 6xx/7xxx, 8xx, 8xxx
powerpc: Use scripts/mkuboot.sh instead of 'mkimage'
powerpc/5200: update defconfigs
This reverts commit 14f0aa3593.
That commit was needed earlier because system call restarting for
OABI (compat) required an executable stack and thus had problems
with NX. Since ab72b00734 ("ARM: Fix signal restart issues
with NX and OABI compat") has reworked the code to not require an
executable stack anymore, we can re-enable NX support for kernels
with OABI (compat) support.
Signed-off-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Because of the include of the decompress_inflate.c file from
boot/compress/misc.c, there are different flush() defines:
In file included from arch/arm/boot/compressed/misc.c:249:
arch/arm/boot/compressed/../../../../lib/decompress_inflate.c:138:29: error: macro "flush" passed 2 arguments, but takes just 0
Fix this by removing the define of flush() in misc.c for
CONFIG_DEBUG_ICEDCC as it's already defined in mach/uncompress.h,
and that is being included unconditionally.
Also use a static inline function instead of define
for mach-mxc and mach-gemini to avoid similar bug
for those platforms.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This converts the cpu_relax() to a udelay(1), which fixes up issues with
the EEPROM polling occasionally timing out.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
do_add_mount() should sanitize mnt_flags
CIFS shouldn't make mountpoints shrinkable
mnt_flags fixes in do_remount()
attach_recursive_mnt() needs to hold vfsmount_lock over set_mnt_shared()
may_umount() needs namespace_sem
Fix configfs leak
Fix the -ESTALE handling in do_filp_open()
ecryptfs: Fix refcnt leak on ecryptfs_follow_link() error path
Fix ACC_MODE() for real
Unrot uml mconsole a bit
hppfs: handle ->put_link()
Kill 9p readlink()
fix autofs/afs/etc. magic mountpoint breakage
Commit 62edab9056 (from June 2009
but merged in 2.6.33) changes notify_die to pass dr6 by
reference.
However, it forgets to fix the check for DR_STEP in kmmio.c,
breaking mmiotrace. It also passes a wrong value to the post
handler.
This simple fix makes mmiotrace work again.
Signed-off-by: Luca Barbieri <luca@luca-barbieri.com>
Acked-by: K.Prasad <prasad@linux.vnet.ibm.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <1263634770-14578-1-git-send-email-luca@luca-barbieri.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, uv: Ensure hub revision set for all ACPI modes.
x86, uv: Add function retrieving node controller revision number
x86: xen: 64-bit kernel RPL should be 0
x86: kernel_thread() -- initialize SS to a known state
x86/agp: Fix agp_amd64_init and agp_amd64_cleanup
x86: SGI UV: Fix mapping of MMIO registers
x86: mce.h: Fix warning in header checks
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
perf tools: Check if /dev/null can be used as the -o gcc argument
perf tools: Move QUIET_STDERR def to before first use
perf: Stop stack frame walking off kernel addresses boundaries
The m68knommu coldfire pit clocksource looks like it was incorrectly
marked as a continuous clocksource. Running with it marked as a
continuous clocksource could cause hangs when the system switches to
highres mode or enables nohz.
This patch removes the CLOCK_SOURCE_IS_CONTINUOUS flag on the coldfire pit
clocksource. This will disallow systems using this clocksource from
entering oneshot mode (disabling highres timers and nohz).
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Greg Ungerer <gerg@snapgear.com>
Cc: Steven King <sfking@fdwdc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus/samsung' of git://git.fluff.org/bjdooks/linux:
ARM: MINI2440: Fixup __initdata usage
ARM: MINI2440: Fix crash on boot due to improper __initdata qualifier
ARM: SMDK6410: Specify no GPIO for B_PWR_5V regulator
ARM: S3C: NAND: Check the existence of nr_map before copying
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: sentelic - fix left/right horizontal scroll mapping
Input: pmouse - move Sentelic probe down the list
Input: add compat support for sysfs and /proc capabilities output
Input: i8042 - add Dritek quirk for Acer Aspire 5610.
Input: xbox - do not use GFP_KERNEL under spinlock
Input: psmouse - fix Synaptics detection when protocol is disabled
Input: bcm5974 - report ABS_MT events
Input: davinci_keyscan - add device_enable method to platform data
Input: evdev - be less aggressive about sending SIGIO notifies
Input: atkbd - fix canceling event_work in disconnect
Input: serio - fix potential deadlock when unbinding drivers
Input: gf2k - fix &&/|| confusion in gf2k_connect()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mattst88/alpha-2.6:
alpha: cpumask_of_node() should handle -1 as a node
alpha: add myself as a maintainer, and drop mention of 2.4
Ensure that UV hub revision is set for all ACPI modes.
Signed-off-by: Russ Anderson <rja@sgi.com>
LKML-Reference: <20100115180908.GB7757@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add function for determining the revision id of the SGI UV
node controller chip (HUB). This function is needed in a
subsequent patch.
Signed-off-by: Jack Steiner <steiner@sgi.com>
LKML-Reference: <20100112210904.GA24546@sgi.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
This patch converts sparc (specifically sparc32) to use GENERIC_TIME via
the arch_getoffset() infrastructure, reducing the amount of arch
specific code we need to maintain.
The sparc architecture is one of the last 3 arches that need to be
converted.
This patch applies on top of Linus' current -git tree
I've taken my best swing at converting this, but I'm not 100% confident
I got it right. My cross-compiler is now out of date (gcc4.2) so I
wasn't able to check if it compiled. Any assistance from arch
maintainers or testers to get this merged would be great.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some of the __initdata tags which are currently inappropriate for
platform_device and some of the platform data. These can be returned once
support for copying platform devices and data is added.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch fix mini2440 crash on boot due to improper __initdata
qualifier on mini2440_led1_pdata.
Signed-off-by: Uri Yosef <uri.yosef@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Move the defintion and lock helper routines for the cpu hotplug driver
lock from pseries to powerpc code to avoid build breaks for platforms
other than pseries that use cpu hotplug.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Acked-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It looks like the previous patch sent out to move RTAS and
other items from /proc/ppc64 to /proc/powerpc missed a few
files needed for RAS and DLPAR functionality.
Original Patch here:
http://lists.ozlabs.org/pipermail/linuxppc-dev/2009-September/076096.html
This patch updates the remaining files to be created under /proc/powerpc.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The newly added fixup for buggy dcbX insn's has
a bug that always trigger a kernel TLB walk so a user space
dcbX insn will cause a Kernel Machine Check if it hits DTLB error.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We noticed that recent kernels didn't boot on our 1GHz Canyonlands 460EX
boards anymore. As it seems, patch 8d165db1 [powerpc: Improve
decrementer accuracy] introduced this problem. The routine div_sc()
overflows with shift = 32 resulting in this incorrect setup:
time_init: decrementer frequency = 1000.000012 MHz
time_init: processor frequency = 1000.000012 MHz
clocksource: timebase mult[400000] shift[22] registered
clockevent: decrementer mult[33] shift[32] cpu[0]
This patch now introduces a local div_dc64() version of this function
so that this overflow doesn't happen anymore.
Signed-off-by: Stefan Roese <sr@denx.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Detlev Zundel <dzu@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
get_viotape_info() declares a vio_waitevent on the stack, which
contains a completion, but never initialises the completion.
I have no idea how this ever worked, and on recent kernels it causes
an oops in handle_tape_event() when we access the non-initialised
completion.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.
I.e. either use rlimit helpers added in
3e10e716ab
or ACCESS_ONCE if not applicable.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: linuxppc-dev@ozlabs.org
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Commit 57b150cce8 (irq: only update affinity if
->set_affinity() is sucessfull) broke xics irq affinity.
We need to use the cpumask passed in, instead of accessing ->affinity directly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
It seems there is a thinko in the TLB invalidation code that makes the
tlbie in the loop executed just once. The intended check was probably
'gt', not 'lt'.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Various kernel asm modifies SRR0/SRR1 just before executing
a rfi. If such code crosses a page boundary you risk a TLB miss
which will clobber SRR0/SRR1. Avoid this by always pinning
kernel instruction TLB space.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Since the fixed voltage regulator grew support for GPIO based
enables and GPIO 0 is valid on some systems we need to specify
that there is no valid GPIO enable control.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
This patch adds support for the lis3lv02d motion sensor connected via
i2c on the Ecovec board. Tested with evtest.
Signed-off-by: NISHIMOTO Hiroki <nishimoto.hiroki@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
CC: Richard Henderson <rth@twiddle.net>
CC: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Matt Turner <mattst88@gmail.com>
CC: linux-alpha@vger.kernel.org
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Anton Blanchard <anton@samba.org>
It doesn't account for phys_base like it should, fix by using
page_to_pfn().
While we're here, make virt_to_page() use pfn_to_page() as well, so we
consistently use the asm/memory-model.h abstractions instead of
open-coding memory model assumptions.
Tested-by: Kristoffer Glembo <kristoffer@gaisler.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the structure field nr_map is optional, we need to check whether the
chip number map is provided to avoid unexpected NULL pointer exception.
Signed-off-by: Ramax Lo <ramaxlo@gmail.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Commit ac4c2a3bbe broke the build
of all powerpc boot wrappers.
It attempts to add an include of autoconf.h but used the wrong
path for it. It also adds -D__KERNEL__ to our boot wrapper, both
things that we pretty much didn't do on purpose so far.
We want our boot wrapper to remain independent enough of the kernel
for various reasons, one of them being that you can "wrap" an existing
kernel at distro install time which allows to ship one kernel image
and a set of boot wrappers for different platforms, the wrappers
don't have to be built out of the same kernel build tree.
It's also incorrect to do what the patch does in our boot environment
since we may not have a proper alignment exception handler which means
we may not be able to fixup the few cases where an unaligned access will
need SW emulation (depends on the core variant, could be when crossing
page or segment boundaries for example).
This patch fixes it by putting the old code back in and using the
new "fancy" variant only when CONFIG_HAVE_EFFICIENT_UNALIGNED_ACCESS
is set, which happens not to be set on powerpc since we don't include
autoconf.h. It also reverts the changes to our boot wrapper Makefile.
This means that x86 should, afaik, keep the optimisations since its
boot wrapper does include autoconf.h and define __KERNEL__ (though I
doubt they make that much different outside of slow embedded processors).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sys_recvmmsg is reachable via sys_socketcall. So unwire it again since
there is no point in having two entry points for it.
Also put it to the ignore list so we don't get reminded anymore in order
to wire it up.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This one will trap, generates shorter code and emits better debug data
than the generic version.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Finally move it to the place where it belongs to and make get rid of
it for !CONFIG_SMP.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
smp_processor_id() is supposed to work before setup_arch() gets called.
Before that smp_processor_id() may return just an arbitrary value that
is contained in the uninitialized boot lowcore.
So provide the arch function which will override the weak function in
init/main.c.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Make sure compiler won't do weird things with limits. E.g. fetching
them twice may return 2 different values after writable limits are
implemented.
I.e. either use rlimit helpers added in
3e10e716ab
or ACCESS_ONCE if not applicable.
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: linux-s390@vger.kernel.org
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The TIF_USEDFPU bit is always 0 for s390 and it is not tested anywhere.
Remove the bit. At the same time remove the calls to clear_used_math()
as well. The PF_USED_MATH bit is never set for s390 either.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The code in do_signal sets the TIF_SINGLE_STEP bit and calls
tracehook_signal_handler after the signal frame has been set up.
This causes two SIGTRAP signals to be delivered to the tracer.
Stop setting the TIF_SINGLE_STEP bit in do_signal to get the
correct number of SIGTRAPs.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Clear the TIF_SINGLE_STEP bit in copy_thread. The new process did not get
a PER event of its own. It is wrong deliver a SIGTRAP that was meant for
the parent process.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If the current task enables / disables PER tracing for itself the
PER control registers need to be loaded in FixPerRegisters.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Easy fix for a regression introduced in 2.6.31.
On managed CPUs the cpufreq.c core will call driver->exit(cpu) on the
managed cpus and powernow_k8 will free the core's data.
Later driver->get(cpu) function might get called trying to read out the
current freq of a managed cpu and the NULL pointer check does not work on
the freed object -> better set it to NULL.
->get() is unsigned and must return 0 as invalid frequency.
Reference:
http://bugzilla.kernel.org/show_bug.cgi?id=14391
Signed-off-by: Thomas Renninger <trenn@suse.de>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
CC: stable@kernel.org
Signed-off-by: Dave Jones <davej@redhat.com>
There is no such GPIO for udc vbus sensing, put '-1' instead of default
'0' as '0' does mean a valid GPIO.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Setting LC_CTYPE=C breaks localized messages in some setups. With only
LC_COLLATE=C and LC_NUMERIC=C, we get almost all we need, except for not
so defined character classes and tolower()/toupper(). The former is not
a big issue, because we can assume that e.g. [:alpha:] will always
include a-zA-Z and we only ever process ASCII input. The latter seems
only affect arch/sh/tools/gen-mach-types, which we can handle separately.
So after this patch the meaning of ranges like [a-z], the behavior of
sort and join, etc. should be the same everywhere and at the same time
gcc should be able to print localized waring and error messages.
LC_NUMERIC=C might not be necessary, but setting it doesn't hurt.
Reported-by: Simon Horman <horms@verge.net.au>
Reported-by: Sergei Trofimovich <slyfox@inbox.ru>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Simon Horman <horms@verge.net.au>
Tested-by: Masami Hiramatsu <mhiramat@redhat.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
Under Xen 64 bit guests actually run their kernel in ring 3,
however the hypervisor takes care of squashing descriptor the
RPLs transparently (in order to allow them to continue to
differentiate between user and kernel space CS using the RPL).
Therefore the Xen paravirt backend should use RPL==0 instead of
1 (or 3). Using RPL==1 causes generic arch code to take
incorrect code paths because it uses "testl $3, <CS>, je foo"
type tests for a userspace CS and this considers 1==userspace.
This issue was previously masked because get_kernel_rpl() was
omitted when setting CS in kernel_thread(). This was fixed when
kernel_thread() was unified with 32 bit in
f443ff4201.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1263377768-19600-2-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Before the kernel_thread was converted into "C" we had
pt_regs::ss set to __KERNEL_DS (by SAVE_ALL asm macro).
Though I must admit I didn't find any *explicit* load of
%ss from this structure the better to be on a safe side
and set it to a known value.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Christian Kujau <lists@nerdbynature.de>
Cc: Jeremy Fitzhardinge <Jeremy.Fitzhardinge@citrix.com>
Cc: Brian Gerst <brgerst@gmail.com>
LKML-Reference: <1263377768-19600-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the regression introduced by the commit
f405d2c023.
The above commit fixes the following issue:
http://marc.info/?l=linux-kernel&m=126192729110083&w=2
However, it doesn't work properly when you remove and insert the
agp_amd64 module again.
agp_amd64_init() and agp_amd64_cleanup should be called only
when gart_iommu is not called earlier (that is, the GART IOMMU
is not enabled). We need to use 'gart_iommu_aperture' to see if
GART IOMMU is enabled or not.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: mitov@issp.bas.bg
Cc: davej@redhat.com
LKML-Reference: <20100104161603L.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the problem of the initialization code not correctly
mapping the entire MMIO space on a UV system. A side effect is
the map_high() interface needed to be changed to accommodate
different address and size shifts.
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Mike Habeck <habeck@sgi.com>
Cc: <stable@kernel.org>
Cc: Jack Steiner <steiner@sgi.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <4B479202.7080705@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Someone isn't reading their build output: Move the definition
out of the exported header.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: linux-kernel@vger.kernelorg
Signed-off-by: Ingo Molnar <mingo@elte.hu>
While processing kernel perf callchains, an bad entry can be
considered as a valid stack pointer but not as a kernel address.
In this case, we hang in an endless loop. This can happen in an
x86-32 kernel after processing the last entry in a kernel
stacktrace.
Just stop the stack frame walking after we encounter an invalid
kernel address.
This fixes a hard lockup in x86-32.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <1262227945-27014-1-git-send-regression-fweisbec@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* master.kernel.org:/home/rmk/linux-2.6-arm:
ARM: Ensure ARMv6/7 mm files are built using appropriate assembler options
ARM: Fix wrong dmb
ARM: 5874/1: serial21285: fix disable_irq-from-interrupt-handler deadlock
ARM: 5873/1: ARM: Fix the reset logic for ARM RealView boards
ARM: 5872/1: ARM: include needed linux/cpu.h in asm/cpu.h
ARM: 5871/1: arch/arm: Fix build failure for lpd7a404_defconfig caused by missing includes
ARM: 5870/1: arch/arm: Fix build failure for defconfigs without CONFIG_ISA_DMA_API set
ARM: 5868/1: ARM: fix "BUG: using smp_processor_id() in preemptible code"
ARM: 5867/1: Update U300 defconfig
ARM: 5866/1: arm ptrace: use unsigned types for kernel pt_regs
[ARM] pxa: fix strange characters in zaurus gpio .desc
ARM: add missing recvmmsg syscall number
[ARM] pxa: fix compiler warnings of unused variable 'id' in cpu_is_pxa9*()
[ARM] pxa: update pwm_backlight->notify() to include missed 'struct device *'
[ARM] pxa: enable L2 if present in XSC3
[ARM] pxa: do not enable L2 after MMU is enabled
Fix compilation breakage of all m68knommu targets:
CC arch/m68knommu/kernel/asm-offsets.s
In file included from include/linux/sched.h:77,
from arch/m68knommu/kernel/asm-offsets.c:12:
include/linux/percpu.h: In function 'per_cpu_ptr_to_phys':
include/linux/percpu.h:161: error: implicit declaration of function 'virt_to_phy
This is broken in linux-2.6.33-rc3.
Change the definitions of __pa() and __va() to not use virt_to_phys()
and phys_to_virt(). Trivial 1:1 conversion required for the non-MMU case.
A side effect if this is that the m68knommu can now use asm/virtconvert.h
for the definition of virt_to_phys() and phys_to_virt().
Also cleaned up the definition of page_to_phys() when moving into
virtconvert.h.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
A kernel with both ARMv6 and ARMv7 selected results in build errors.
Fix this by specifying the proper architectures for these assembly
files.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The __kuser_cmpxchg code uses an ARMv6 dmb instruction, rather than
one based upon the architecture being built for. Switch to using
the macro provided for this purpose, which also eliminates the
need for an ifdef.
Acked-by: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It moves to the same directory as the boot files in other formats.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/796/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
pcibus_to_node can return -1 if we cannot determine which node a pci bus
is on. If passed -1, cpumask_of_node will negatively index the lookup array
and pull in random data:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
00000000,00000003,00000000,00000000
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
64-65
Change cpumask_of_node to check for -1 and return cpu_all_mask in this
case:
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpus
ffffffff,ffffffff,ffffffff,ffffffff
# cat /sys/devices/pci0000:00/0000:00:01.0/local_cpulist
0-127
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andrew Morton <akpm@linux-foundation.org>
Patchwork: http://patchwork.linux-mips.org/patch/831/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With typical mult and shift values, the calculation for Octeon's sched_clock
overflows when using 64-bit arithmetic. Use 128-bit calculations instead.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/849/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A call to r4k_clocksource_init() was added to plat_time_init(), but
when init_mips_clock_source() calls the same function, boot fails in
clockevents_register_device(). This patch removes the extraneous call.
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Patchwork: http://patchwork.linux-mips.org/patch/803/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the advent of function graph tracing on MIPS, Octeon needs a high
precision sched_clock() implementation. Without it, most timing
numbers are reported as 0.000.
This new sched_clock just uses the 64-bit cycle counter appropriately
scaled.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/805/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit 898d357b5262f9e26bc2418e01f8676e80d9867e (lmo) /
6acc7d485c (kernel.org) ("Fix and enhance
built-in kernel command line") arcs_cmdline[] does not contain built-in
command line. The commit introduce CONFIG_CMDLINE_BOOL and
CONFIG_CMDLINE_OVERRIDE to control built-in command line, and now we can
use them instead of platform-specific built-in command line processing.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Patchwork: http://patchwork.linux-mips.org/patch/802/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips_machine_halt() is same as mips_machine_restart(). Also delete the
registration of _machine_halt and pm_power_off because mips_machine_halt()
is the restart function.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/798/
Reviewed-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
An unused leftover from the old KGDB implementation.
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/794/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
sizeof(dp) is just the size of the pointer. Change it to the size of the
referenced structure.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression *x;
expression f;
type T;
@@
*f(...,(T)x,...)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Patchwork: http://patchwork.linux-mips.org/patch/789/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
o Remove the .initrd section. The initrd section was already handled
when vmlinux was linked.
o Discard .MIPS.options, .options, .pdr, .reginfo, .comment and .note
sections. If .MIPS.options is not removed, kernels compiled with gcc
3.4.6 will not boot.
o Clean up the file format.
o Remove several other unneeded sections.
Tested with GCC 3.4.6 and 4.4.1 with and without initrd.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/785/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since AUDMUX configuration appears to be one of the common stumbling
blocks for people setting up i.MX audio try to provide some diagnostic
information describing the current setup to assisist people in working
out what's going on.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Revert commit 2fbd07a5f5, as this commit
breaks an IBM platform with quad-core Xeon cpu's.
According to Suresh, this might be an IBM platform issue, as on other
Intel platforms with <= 8 logical cpu's, logical flat mode works fine
irespective of physical apic id values (inline with the xapic
architecture).
Revert this for now because of the IBM platform breakage.
Another version will be re-submitted after the complete analysis.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The list macros use LIST_POISON1 and LIST_POISON2 as undereferencable
pointers in order to trap erronous use of freed list_heads. Unfortunately
userspace can arrange for those pointers to actually be dereferencable,
potentially turning an oops to an expolit.
To avoid this allow architectures (currently x86_64 only) to override
the default values for these pointers with truly-undereferencable values.
This is easy on x86_64 as the virtual address space is large and contains
areas that cannot be mapped.
Other 64-bit architectures will likely find similar unmapped ranges.
[ingo: switch to 0xdead000000000000 as the unmapped area]
[ingo: add comments, cleanup]
[jaswinder: eliminate sparse warnings]
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Avi Kivity <avi@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update the defconfig for the ASB2303 platform.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Access to the ASB2305's PCnet32 NIC doesn't work correctly because when
the NIC attempts to update the ring buffer flags by DMA, the change to RAM
crops up about 17uS after the interrupt line is asserted. This is almost
certainly due to a bug in the PCI bridge FPGA on that board.
We can get around this by making dma_alloc_coherent() put the ring buffer
in the SRAM attached to the PCI bridge rather than in the SDRAM.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Insert PCI root bus resources for the MN10300-based ASB2305 development
kit motherboard. This is required because the CPU's window onto the PCI
bus address space is considerably smaller than the CPU's full address
space and non-PCI devices lie outside of the PCI window that we might want
to access.
Without this patch, the PCI root bus uses the platform-level bus
resources, and these are then confined to the PCI window, thus making
platform_device_add() reject devices outside of this window.
We also add a reservation for the PCI SRAM region.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the generic pci_enable_resources() instead of the arch-specific code.
Unlike this arch-specific code, the generic version:
- checks PCI_NUM_RESOURCES (11), not 6, resources
- skips resources that have neither IORESOURCE_IO nor IORESOURCE_MEM set
- skips ROM resources unless IORESOURCE_ROM_ENABLE is set
- checks for resource collisions with "!r->parent"
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use KERN_ERR not KERN_ERROR in the ASB2305 platform code.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/cpu never existed for mn10300; the files they are looking for are in
asm.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Wire up missing new system calls for MN10300.
Signed-off-by: David Howells <dhowelsl@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
gcc 4.2.1 for MN10300 is more agressive than the older gcc in
reordering/moving other insns between an insn that sets flags and an insn
that uses those flags. This leads to trouble with asm statements which
are missing an explicit "cc" clobber. This patch adds the explicit "cc"
clobber to asm statements which do indeed clobber the condition flags.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The gcc-4.2.1 based toolchain for MN10300 adds some new note sections
which need to be stripped from the binary image. This patch takes care of
that.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a signal stack handling problem in the MN10300 arch. When new
threads are cloned with CLONE_VM, they don't inherit the alternate signal
stack. They do share the signal flags, though. When deciding whether to
use an alternate stack, the arch code needs to check to make sure the task
struct contains a valid alternate stack. This patch fixes the MN10300
arch by using the sas_ss_flags() test provided by sched.h rather than the
on_sig_stack() test which is insufficient by itself.
Signed-off-by: Mark Salter <msalter@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The necessary changes to the x86 Kconfig and boot/compressed to allow the
use of this new compression method
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- changes to ach/arch/boot/Makefile to make it easier to add new
compression types
- new piggy.lzo.S necessary for lzo compression
- changes in arch/arm/boot/compressed/misc.c to allow the use of lzo or
gzip, depending on the config
- Kconfig support
Signed-off-by: Albin Tonnerre <albin.tonnerre@free-electrons.com>
Tested-by: Wu Zhangjin <wuzhangjin@gmail.com>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Russell King <rmk@arm.linux.org.uk>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
JFFS2 uses lesser compression ratio and inflate always ends up in "copy
direct from output" case.
This patch tries to optimize the direct copy procedure. Uses
get_unaligned() but only in one place.
The copy loop just above this one can also use this optimization, but I
havn't done so as I have not tested if it is a win there too.
On my MPC8321 this is about 17% faster on my JFFS2 root FS than the
original.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Cc: Roel Kluin <roel.kluin@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Makes it consistent with the extern declaration, used when CONFIG_HIGHMEM
is set Removes redundant casts in printout messages
Signed-off-by: Andreas Fenkart <andreas.fenkart@streamunlimited.com>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Cc: Lennox Wu <lennox.wu@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Extend the patch from Philby John to the other "RealView" boards.
Rename the constants and offsets to reflect their actual functions.
Cc: Philby John <pjohn@in.mvista.com>
Signed-off-by: Colin Tuckley <colin.tuckley@arm.com>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The file arch/arm/include/asm/cpu.h needs to include 'linux/cpu.h' to
meet its dependency. Otherwise when using "struct cpuinfo_arm" and
including just 'asm/cpu.h' throws below error -
arch/arm/include/asm/cpu.h:16: error: field 'cpu' has incomplete type
To fix this otherway, one can also include both linux/cpu.h and
asm/cpu.h but it shoudn't be that way. So this patch fixes this by
including the linux/cpu.h in asm/cpu.h, so that including alone
asm/cpu.h is enough.
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a build failure [1] due to missing includes
This should make the arm tree build again with lpd7a404_defconfig
References:
http://kisskb.ellerman.id.au/kisskb/buildresult/1983329/
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A lot of ARM-defconfigs (those without CONFIG_ISA_DMA_API set) fail to
build [1][2][3] due to the changes of the patch
[PATCH] PCI: Clean up build for CONFIG_PCI_QUIRKS unset
by Rafael J. Wysocki (Sat, 2 Jan 2010 22:57:24 +0100) [4]
as the referenced variable 'isa_dma_bridge_buggy' in asm/dma.h is
enclosed by the CONFIG_ISA_DMA_API conditional all configs without this
setting fail to build.
I'm not sure wether moving the condition is the right way to solve the
issue, but atleast it fixes the issue :)
References:
[1] http://kisskb.ellerman.id.au/kisskb/buildresult/1983354/
[2] http://kisskb.ellerman.id.au/kisskb/buildresult/1983333/
[3] http://kisskb.ellerman.id.au/kisskb/buildresult/1983337/
[4] http://lkml.org/lkml/2010/1/2/102
Signed-off-by: Peter Huewe <peterhuewe@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Dynamically allocate the CPUFreq frequency table on OMAP2xxx chips.
This fixes some compilation problems, since the kernel may not know
what chip it is running on until boot-time. This also reduces the size
of the CPUFreq frequency table.
Problem originally reported by Felipe Balbi <felipe.balbi@nokia.com>.
Thanks also for comments on the patch from Felipe and Kevin.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
A subsequent patch adds code on OMAP2xxx to dynamically allocate the
CPUFreq frequency table in clk_init_cpufreq_table(), so for it to
avoid a leak, it will need a corresponding function to free the
memory. This patch adds clk_exit_cpufreq_table() with generic
code to call a chip-specific variant inside the clockfw_lock spinlock via
struct clk_functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Revise some of the comments in the OMAP2xxx OPP data for clarity.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
if we enable CPUFREQ we can't build omap2 for two reasons,
one of them is fixed by the patch below.
It's failing because the __must_be_array() check in
ARRAY_SIZE() is failing and printing the following message:
arch/arm/mach-omap2/clock2xxx.c:453: error: negative width in bit-field '<anonymous>'
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
[paul@pwsan.com: commit message updated; changed rate variable name]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 52650505fb added an __initdata
decoration to the structure containing the clk_enable and clk_disable
functions. Once init data was freed, these pointers went to null, and
the next enable or disable call caused the kernel to crash. This
change removes this decoration.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: patch manually split and commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
This change adds in some missing clocks that were needed as a result
of 526505... (OMAP1 clock: convert mach-omap1/clock.h to
mach-omap1/clock_data.c). Prior to this, it was just assumed that
these clocks existed for all devices, and it was used directly instead
of calling it out with a clock_get call or similar. So, not having
the CK_7XX meant these clocks weren't being used anymore for omap 7xx
devices, which broke things badly.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
[paul@pwsan.com: commit message edited]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The only symbols that should be exported are symbols that are to be
called from loadable kernel modules, e.g., device drivers. In the
context of plat-omap/clock.c, these should only be the Linux clock
interface symbols as defined by include/linux/clk.h. Core code
doesn't need these symbols to be exported. Also, clean up an old
comment while here.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add necessary definitions to clock framework to allow changing
dpll4_m5_ck rate. This is used by the camera code.
Signed-off-by: Jouni Högander <jouni.hogander@nokia.com>
Signed-off-by: Tuukka Toivonen <tuukka.o.toivonen@nokia.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The correct parent of the McBSP 2, 3, and 4 functional clocks is
PER_96M_FCLK, not CORE_96M_FCLK. Fix this in the OMAP clock tree.
Reported by Nicole Chalhoub <n-chalhoub@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Nicole Chalhoub <n-chalhoub@ti.com>
UART1 & 2 were missing clockdomains resulting in broken omap_hwmod
init for these devices.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 10db25fea4 causes the following
kernel messages during N800 boot (and presumably all other 2420
boards):
[ 0.000000] BUG: mapping for 0x58000000 at 0xe0000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x59000000 at 0xe1000000 overlaps vmalloc space
[ 0.000000] BUG: mapping for 0x5a000000 at 0xe2000000 overlaps vmalloc space
Fix by remapping the IVA memory areas somewhere outside vmalloc space.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Out of the three major OMAP2 chip types, OMAP2420, OMAP2430, and OMAP3430,
we only map the IVA on OMAP2420. The memory mapping is not shared between
OMAP2420 and OMAP2430, so it is inappropriate to label those macros as
'24XX'; this patch changes them to '2420'.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In OMAP2/3 some of the clock-domains which did not have control
facility were being falsely written to and read using the CM_CLKSTCTRL
register though it did not exist for them. One check is added to remove
this flaw.
Signed-off-by: Abhijit Pagare <abhijitpagare@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
kgdb: Fix kernel-doc format error in kgdb.h
blackfin,kgdb: Do not put PC in gdb_regs into retx.
blackfin,kgdb,probe_kernel: Cleanup probe_kernel_read/write
maccess,probe_kernel: Allow arch specific override probe_kernel_(read|write)
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86, irq: Check move_in_progress before freeing the vector mapping
x86: copy_from_user() should not return -EFAULT
Revert "x86: Side-step lguest problem by only building cmpxchg8b_emu for pre-Pentium"
x86/pci: Intel ioh bus num reg accessing fix
x86: Fix size for ex trampoline with 32bit
