Modules: Documentation,HDA Codec driver
Fix the support of laptops with AD1986A HD-audio codec.
Added new models '3stack' and 'laptop'. Currently, fixed for FSC V2060
and Samsung M50.
Also fixed the description of missing models in ALSA-Configuration.txt.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
Add more PCI subsystem IDs of DVB cards to the blacklist of cards the
driver is to ignore.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: CS5535 driver
The 10 ms sleeps while waiting for AC'97 codec register reads/writes to
complete are excessive given the maxmium time is one AC'97 frame (~21 us).
With AC'97 codecs with integrated touchscreens (like the UCB1400) this
improves the interactive performance of the touchscreen.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Documentation,HDA Codec driver
Added a new model 'lg' for LG laptop (m1 express dual) with ALC880 codec.
Also clean up the initialization/unsol_event hooks in patch_realtek.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
- Fixed recording of AD1981HD/AD1983/AD1986A
- Added model 'hp' to AD1981HD for HP nx6320
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA generic driver
Add 'fujitsu' model for ALC262 patch to support a FSC laptop.
The internal speaker is turned on/off with jack sensing.
Also fixed alc262 'basic' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: ICE1712 driver
I posted this patch to bug 1806 a while back, and have been awaiting a
reply or commit. It currently reports the Locked/No Signal text
backwards in envy24control, since i was using an older version of
envy24control when I wrote the original code. The Locked/No Signal test
was recently reversed in envy24control cvs, so the test in my code needs
to be reversed as well. Here is the patch, once again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds mixer controls to the 'test' ALC260 model which allow the
user to selectively enable or disable the SPDIF output pins. This should
assist people identify digital outputs on machines which bring them to the
outside world.
Note that while the patch *should* work, I cannot personally verify it since
my laptop doesn't bring the SPDIF lines out.
As for the GPIO switches added in patch 4, these controls are currently
only compiled in if debug mode is selected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch is janitorial - it cleans up a number of cosmetic issues with
the 'fujitsu' and 'test' models. Issues addressed:
* spaces instead of tabs used for some indents,
* clarified/corrected selected comments.
Unlike a patch from earlier this week, this keeps both ADCs connected to
the mic1 pin widget by default. I believe this is the better default, since
some laptops don't bring the line1 widget to the outside world. Most (if
not all) do bring mic1 out though, so it seems to me that this default
should remain in place.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds a new 'acer' model. It is based on work by Rimas and many
other dedicated Acer owners over the past few weeks (see bug number
1618) - kudos to them. This adds support for a variety of Acer laptops,
although we are still in the process of collecting pci/subsystem IDs to add.
There are still some potentially outstanding issues: there are reports that
the CD control might not yet be functional for example. However, the time
is probably right to get a 'first cut' into the kernel which can be refined
as more test reports come in.
From the reports by various Acer owners, this code allows them to record
from internal mics and external jacks. Playback also seems to work to all
external jacks and the internal speaker. The 'beep' control doesn't appear
functional at the moment.
This patch depends on the changes made in patch 3/7.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds 'test' model mixer switches for the GPIO controls found on
the ALC260. It has been found that some laptops (eg: Acer) can use these to
enable particular controls, so it would be useful to have access to these
via the 'test' model. It will make testing new models easy, especially if
certain outputs cannot be made to work any other way.
This patch *should* work, but because the GPIO pins don't do anything in
my laptop I cannot personally verify that all this works as expected.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch generalises a structure added for the 'fujitsu' model but which
is potentially useful for other models as well. It turns the
'alc260_fujitsu_adc_nids' array into 'alc260_dual_adc_nids'; for other
models which decide to utilise the dual ADC functionality there's really
no reason why they need to define their own list of ADC nids.
The 'fujitsu' model preset is adjusted accordingly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch adds functionality which switches the input/output buffer enables
of retasking pins when the user changes their mode with the mode control.
This probably reduces noise *slightly* for recording compared to the case
where both input and output buffers were enabled simultaneously.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This patch fixes input mux labels used for the ALC260 'test' model. This is
needed to avoid confusion which comes about because the two ADCs in the
ALC260 have slightly different mappings for their input selectors. Since
this is just the test model it's sufficient to simply report both options
where they exist. If a model comes along for which this becomes an issue,
the ALC260 input mux code will have to be extended to allow different mux
layouts for different ADCs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Intel driver
Switch the method to measure the current DMA position automatically
from position-buffer mode to LPIB-read mode with a sanity check.
Some hardwares seems to have problem with the position buffer.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver,HDA Intel driver
Switch to single_cmd mode automatically as a fallback when CORB/RIRB
communication doesn't work well. It may make the driver working on
some devices with broken BIOS/ACPI support.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
It seems that hardware requires some time to reset bus master registers.
We need to wait until ICH_RESETREGS bit is not released.
The suggestion and symptom was described by Mike Gorchak <lestat@i.com.ua>.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: HDA Codec driver
The following patch adds a 'test' ALC260 model specification to the
patch_realtek.c driver if CONFIG_SND_DEBUG is set. This is similar to the
'test' ALC880 model in that it sets up mixer controls for almost everything
to make it easier for people to test their laptop/soundcard when working out
what pin widgets are connected to which real-world devices.
This patch assumes my previous patch (adding the second PCM to the ALC260)
has previously been applied since it uses infrastructure added by that
patch.
In developing this patch it was found that not all retasking pins accept all
the modes - in particular, some ignore the VREFxx variants. The pin mode
control has therefore been tweaked to prevent this becoming a problem in
mixer applications.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Jonathan Woithe <jwoithe@physics.adelaide.edu.au>
The following patch changes the initverbs associated with the output sum
widgets 0x08, 0x09 and 0x0a used with the fujitsu model in patch_realtek.c.
It is against alsa 1.0.11rc3.
Currently these widgets have their output muted, but a close reading of the
datasheet suggests that they don't actually have an output mute. They have
an *input* mute for each of their two inputs and a single output gain. This
patch therefore activates the input mutes and zeros the output gain. It has
not yet been tested but the above interpretation of the ALC260 datasheet
seems correct.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
The following patch against alsa 1.0.11rc3 creates a PCM device (pcm1c) for
the second ADC present on the ALC260 codec used by the hda driver. It also
defines a new mixer control allowing the mode of retasking pins to be set;
this means a user can (for example) designate the headphone jack to be a
second input. With this patch in place it is possible to do 4 channel
recording on laptops equipped with an ALC260 codec assuming both a stereo
line-in jack is provided in addition to a headphone jack.
Mixer controls are provided to allow the headphone jack to be switched as
an input. In addition, an (input only) mode control is configured for
the line-in jack to allow a bias voltage to be requested (VREF80 or VREF50)
so headsets based on condensor microphones have a chance of working.
This patch has been tested on a Fujitsu S7020 laptop and as such these
features are currently only configured for the 'fujitsu' model.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: AC97 Codec
Added the support of static resolution table support for codecs
that the driver cannot probe the volume resolution properly.
The table pointer should be set in each codec patch.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: BT87x driver
- added 0x107d:0x6606 to whitelist
- print also the pci device ID for developers when model is not known
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: ICE1712 driver
Change the value written to hardware configuration register of envy24 chip
in the case of Terratec DMX6fire to restrict the active ADCs & DACs to 6.
Also add the dxr_enable module option to eventually leave the old behaviour
when user requests.
Signed-off-by: Alan Horstmann <gineera@aspect135.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Modules: YMFPCI driver
Added rear_swap module option / kernel parameter to configure the rear
channel swapping. Default value is enable to make the AC3 passthrough
working, but analog only users might revert the previous behaviour.
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: au88x0 driver
Fix the driver codes to run on 64bit architectures.
The patch taken from ALSA BTS bug#1047.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: YMFPCI driver
The routing of the effect 2/3 channels to the digital output is the
opposite of the rear analog output (left/right swapped).
We make the order correct for the digital output (which will make the
analog rear have the channels swapped) to make AC3 output work.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Modules: Documentation,HDA Intel driver
Added single_cmd module option for debugging in the case CORB/RIRB
doesn't work well (e.g. due to wrong irq routings).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: Intel8x0 driver
Fix the detection of tertriary codec on SIS7012, including clean-ups
of relevant codes.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
This little patch add the model for the motherboard K8N51 from Gigabyte
to the known models of ALC boards.
Signed-off-by: Arnaud Patard <apatard@mandriva.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
* Fix init sequence so manually retaskable jacks don't get added to
the line_out list.
* Update intel mobo config defaults to specify surround outputs
as line outs rather than speakers.
Signed-off-by: Matt Porter <mporter@embeddedalley.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Modules: HDA Codec driver
Fix max_channels computation for STAC92xx codecs in the case only
HP pin without line-out pins is detected in the default pin config.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
