Currently, x86_64 and ia64 arches do not clear the corresponding bits
in the node's cpumask when a cpu goes down or cpu bring up is cancelled.
This is buggy since there are pieces of common code where the cpumask is
checked in the cpu down code path to decide on things (like in the slab
down path). PPC does the right thing, but x86_64 and ia64 don't (This
was the reason Sonny hit upon a slab bug during cpu offline on ppc and
could not reproduce on other arches). This patch fixes it for x86_64.
I won't attempt ia64 as I cannot test it.
Credit for spotting this should go to Alok.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They cause quite bad performance regressions on Netburst
This is temporary until we can get new optimized functions
for these CPUs.
This undoes changes that were done in 2.6.15 and in 2.6.16-rc1,
essentially bringing the code back to 2.6.14 level. Only change
is I renamed the X86_FEATURE_K8_C flag to X86_FEATURE_REP_GOOD
and fixed the check for the flag and also fixed some comments.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This avoids BUG_ONs in the low level allocator when an illegal
GFP mask is added.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At resume time, TSC's value or something similar might be changed a lot
against suspend time. This could make system gets a very big lost ticks.
See http://bugzilla.kernel.org/show_bug.cgi?id=5825
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They all have problems with IRQ 0 routing, so just use the APIC on them.
Can be overwritten with "noapicmaintimer"
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another piece from the no-idle-tick patch.
This can be enabled with the "apicmaintimer" option.
This is mainly useful when the PIT/HPET interrupt is unreliable.
Note there are some systems that are known to stop the APIC
timer in C3. For those it will never work, but this case
should be automatically detected.
It also only works with PM timer right now. When HPET is used
the way the main timer handler computes the delay doesn't work.
It should be a bit more efficient because there is one less
regular interrupt to process on the boot processor.
Requires earlier bugfix from Venkatesh
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A kprobe executes IRET early and that could cause NMI recursion
and stack corruption.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a typo/mis-merge in one of the previous patches.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... as they are no longer needed. Since there were hard-coded numbers in the
file, the patch also adds a mechanism to avoid these (otherwise potential
future changes would again and again require adjusting these numbers).
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This unbreaks recursive kprobes which didn't work anymore
due to an earlier patch which converted the debug entry point
to use an IST.
This also allows nesting of the debug entry point too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o This fix was posted for i386 long back. Posting it for x86_64.
http://marc.theaimsgroup.com/?l=linux-kernel&m=110380103229830&w=2
o This patch fixes the problem of secondary cpus boot up. This situation
is faced when kernel is built for default locations like 16MB and
onwards. In this configuration, only primary cpu (BP) comes and
secondary cpus don't boot.
o Problem occurs because in trampoline code, lgdt is not able to load the
GDT as it happens to be situated beyond 16MB. This is due to the fact
that cpu is still in real mode and default operand size is 16bit.
o This patch uses lgdtl instead of lgdt to force operand size to 32
instead of 16.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... reducing the amount of changes Xen has to do.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The explicit and implicit calls to setup_early_printk() were passing
inconsistent arguments.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
hard_smp_processor_id would return the local APIC id instead
of the Linux processor id. On big systems they are often
not identical. safe_smp_processor_id is just a wrapper
around it that does the necessary conversions.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove support for obsolete hardware and cleanup.
- Remove checks for non integrated APICs
- Replace apic_write_around with apic_write.
- Remove apic_read_around
- Remove APIC version reads used by old workarounds
- Remove old workaround for Simics
- Fix indentation
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When building in a separate objtree, file names produced by BUG() & Co. can
get fairly long; printing only the first 50 characters may thus result in
(almost) no useful information. The following change makes it so that rather
the last 50 characters of the filename get printed.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Especially under Xen, where the console cannot be adjusted to more than 25
lines, it is fairly important that the information displayed during a panic
is as compact as possible. Below adjustments work towards that.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Due to a broken condition, the body of the loop that is intended to wait for
the Update-In-Progress bit to get set and then cleared again was never
entered; in fact, the entire loop was optimized out by the compiler. Here is
a change to fix the condition (and to also move the initialization of locals
out of the spin lock protected region).
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was only needed for APM
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
X86_FEATURE_K8_C was a synthetic Linux CPUID flag that was used for some
code optimizations in Opteron C stepping or later. But support for pre C
stepping optimizations has been removed, so this isn't needed anymore.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They used to be used by the reboot code, but not anymore.
Noticed by Jan Beulich
Cc: JBeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
wire mode if there was an i8259 connected to it. This enables getting
timer interrupts in second kernel in legacy mode.
o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
to CPU0. This works well for kexec but not for kdump as we might crash
on a different CPU and second kernel will not see timer interrupts.
o This patch modifies the redirection table entry to deliver the timer
interrupts to the cpu we are rebooting (instead of hardcoding to zero).
This ensures that second kernel receives timer interrupts even on a
non-boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Introduce vSMP arch to the kernel.
This patch:
1. Adds CONFIG_X86_VSMP
2. Adds machine specific macros for local_irq_disabled, local_irq_enabled
and irqs_disabled
3. Writes to the vSMP CTL device to indicate kernel compiled with CONFIG_VSMP
Signed-off-by: Ravikiran Thirumalai <kiran@scalemp.com>
Signed-off-by: Shai Fultheim <shai@scalemp.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently we attempt to restore virtual wire mode on reboot, which only
works if we can figure out where the i8259 is connected. This is very
useful when we are kexec another kernel and likely helpful to an peculiar
BIOS that make assumptions about how the system is setup.
Since the acpi MADT table does not provide the location where the i8259 is
connected we have to look at the hardware to figure it out.
Most systems have the i8259 connected the local apic of the cpu so won't be
affected but people running Opteron and some serverworks chipsets should be
able to use kexec now.
In addition this patch removes the hard coded assumption that the io_apic
that delivers isa interrups is always known to the kernel as io_apic 0.
There does not appear to be anything to guarantee that assumption is true.
And From: Vivek Goyal <vgoyal@in.ibm.com>
A minor fix to the patch which remembers the location of where i8259 is
connected. Now counter i has been replaced by apic. counter i is having
some junk value which was leading to non-detection of i8259 connected to
IOAPIC.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Setting RF (resume flag) allows a debugger to resume execution after a code
breakpoint without tripping the breakpoint again. It is reset by the CPU
after executing one instruction.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It was set as an NMI, but the NMI bit always forces an interrupt
to end up at vector 2. So it was never used. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix
CC arch/x86_64/kernel/nmi.o
linux/arch/x86_64/kernel/nmi.c: In function ???check_nmi_watchdog???:
linux/arch/x86_64/kernel/nmi.c:155: warning: statement with no effect
on Uniprocessor builds.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch uses a static PDA array early at boot and reallocates processor PDA
with node local memory when kmalloc is ready, just before pda_init.
The boot_cpu_pda is needed since the cpu_pda is used even before pda_init for
that cpu is called (to set the static per-cpu areas offset table etc)
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch enables early intialization of cpu_to_node.
apicid_to_node is built by reading the SRAT table, from acpi_numa_init with
ACPI_NUMA and k8_scan_nodes with K8_NUMA.
x86_cpu_to_apicid is built by parsing the ACPI MADT table, from acpi_boot_init.
We combine these two tables and setup cpu_to_node.
Early intialization helps the static per_cpu_areas in getting pages from
correct node.
Change since last release:
Do not initialize early init_cpu_to_node for faking node cases.
Patch tested on TYAN dual core 4P board with K8 only, ACPI_NUMA.
Tested on EM64T NUMA. Also tested with numa=off, numa=fake, and running
a kernel compiled with NUMA on a regular EM64 2 way SMP.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The real vsyscall .text addresses are not mapped when the alternative()
replacement runs early, so use some black magic to access them using
the direct mapping.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They already do this in hardware and the Linux algorithm
actually adds errors.
Cc: mingo@elte.hu
Cc: rohit.seth@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Apic id is in most significant 8 bits of APIC_ID register. Current code
is trying to write apic id to least significant 8 bits. This patch fixes
it.
o This fix enables booting uni kdump capture kernel on a cpu with non-zero
apic id.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove exports that are already exported from the object's source file.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These functions are inlines and shouldn't be exported.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
