This patch shows the correct locations of the heat sensors present in iBook
and PowerBooks G4, instead of displaying them as being on CPU and GPU
(which is not always the case).
Signed-off-by: Colin Leroy <colin@colino.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch limits therm_adt746x to currently existing fan controllers in
Apple laptops. It may avoid problems with future hardware.
Signed-off-by: Colin Leroy <colin@colino.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make MTU field in SA PathRecord and MCMemberRecord a u8 rather than an enum
to avoid complications with endianness.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free all unclaimed MAD receive buffers when userspace closes our file so we
don't leak memory.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check if a client passes a NULL callback into an SA query, and if so, never
call back. This fixes an oops if someone unloads ib_ipoib and ib_sa in
rapid succession. ib_ipoib does an MCMember delete with a NULL callback
and 0 timeout on unload, which is usually fine since the delete completes
successfully. However, if ib_sa is unloaded immediately afterwards, the
delete will be canceled and ib_sa will try to call the (now already
unloaded) ib_ipoib module back with the cancel completion, which triggers
the oops.
Signed-off-by: Roland Dreier <roland@topspin.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It looks like the recent IPMI patches had some -mm-onlyisms.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Cc: Corey Minyard <minyard@acm.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't try to access the i2c bus if the register wasn't successful.
Signed-off-by: Gerd Knorr <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has been sitting for a while, and is causing lots of grief for
people burning CDs. It relaxes the dma restriction for ide-cd,
requiring only the length to be 32-byte aligned, address should be fine
at normal double word alignment.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's a bigger Speedtouch update coming your way after 2.6.12 but in
the meantime, let's at least make it automatically resync if the DSL
signal is lost.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a c99ism.
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'if' clause for ULI526X in tulip_mdio_write allows for
spin_unlock_irqrestore to be called twice for tp->mii_lock. I believe
this is caused by the unintentional omission of a return at the end
of that clause. This patch adds that return.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As a result of the split of the kobject-registration and the
corresponding hotplug event, the order of events for device_add() has
changed. This restores the old order, cause it confused some userspace
applications.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add 0x1601 as 5752M, it's a 5752 but for mobile PCs.
Stolen from Broadcom bcm5700-8.1.55 driver.
Someone forgot to add it to tg3 ;-)
Signed-off-by: David S. Miller <davem@davemloft.net>
The latest speedbumped Apple G5 models have a "bug" in the Open Firmware
device tree that lacks the proper interrupt routing information for the
northbridge i2c controller. Apple's driver silently falls back into a
sub-optimal "polled" mode (heh, maybe they didn't even notice the bug
because of that :), our driver didn't properly check and crashes :(
This patch fixes our driver to not crash, and adds code to the
prom_init() OF trampoline code that detects the "bug" and adds the
missing information back for this chipset revision. This fixes booting
and thermal control on these models.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
with high-speed mode enabled, we switch it to high-speed mode so that
baud_base becomes 921600. However, we also need to multiply the baud
divisor by 8 at the same time, in case it's already in use as a console.
Signed-off-by: David Woodhouse
Acked-by: Tom Rini
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Defines for the different command classes as defined in the MMC and SD
specifications.
Removes the check for high command classes and instead checks that the
command classes needed are present.
Previous solution killed forward compatibility at no apparent gain.
Signed-of-by: Pierre Ossman
If you tried to open a packet device first in read-only mode and then a
second time in read-write mode, the second open succeeded even though the
device was not correctly set up for writing. If you then tried to write
data to the device, the writes would fail with I/O errors.
This patch prevents that problem by making the second open fail with
-EBUSY.
Signed-off-by: Peter Osterlund <petero2@telia.com>
Cc: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new period/dt setting routines don't get the coupling of these
parameters correct. This means that Domain Validation never gets DT
set, and thus the drive gets restricted to U80.
Fix this by restoring the couplings in the set routines.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Tampering with the settings has to be done under the host lock ...
slave_alloc isn't called under any lock, so this has to be done
explicitly.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The allocation of all of our components should be done in slave alloc.
Currently it's rather fancifully refcounted in the queuecommand
callback. This patch moves allocation and destroy to their correct
places in slave_alloc/slave_destory. Now we can guarantee that
everywhere a device is requested, it's actually been allocated, so don't
check for this anymore.
Additionally, the per device busy timer was the only source of potential
use after free. It's been deleted because Linux does the correct thing
with busy returns, so there's no need to implement a separate timer in
the driver.
Finally, implement code that forces all the device parameters to zero
(i.e. async and narrow) in the slave alloc, inform the spi class of the
bios recorded maximums and wait until slave configure before trying
anything more adventurous.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This should finish the spurious queue removal from aic7xxx (there are
other queues that are probably unnecessary, but at least the major and
obviously unnecessary ones are done with).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This was rendered obsolete by the busyq removal; remove some of the last
remnants of its presence.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
pci_alloc_consistent is under 4G by default. Also simplify the
definition of bus_dmamap_t.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's not much sense in sharing code anymore now that aic7xxx uses
various transport class facilities.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The aic7xxx driver has two spurious queues in it's linux glue code: the
busyq which queues incoming commands to the driver and the completeq
which queues finished commands before sending them back to the mid-layer
This patch just removes the busyq and makes the aic finally return the
correct status to get the mid-layer to manage its queueing, so a command
is either committed to the sequencer or returned to the midlayer for
requeue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is similar to the previous sym2 problem. For Domain Validation to
work we can't allow any period setting to turn wide on if it was
previously off.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a basic need not to have parameters go under or over certain
values when doing domain validation. The basic ones are
max_offset, max_width and min_period
This patch makes the transport class take and enforce these three
limits. Currently they can be set by the user, although they could
obviously be read from the HBA's on-board NVRAM area during
slave_configure (if it has one).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
