This patch fixed a bug that was introduced in kernel 2.6.28 for
TabletPC touch data. The wacom_parse_hid routine in wacom_sys.c
should always return 0 even when usb_control_msg got an error.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Although we already have entry for ZEPHYR the match is done
on product name whereas B-2130 BIOS has it in board name.
Reported-by: Yuriy Zhuravlev <stalkerg@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This toshiba has a touchpad with trackpoint and 2 sets of left
and right buttons (above and below touchpad).
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There exist laptops with Elantech touchpads where switching to absolute mode
does not happen, although writing the configuration register succeeds
without error. Reading back the register afterwards reveils that the
absolute mode bit is not set as if masked out by the touchpad firmware.
Always read back register 0x10, make sure that for hardware version 1 the
absolute mode bit is actually set and fail otherwise. This prevents the case
where the touchpad is claimed by the Elantech driver but is nonetheless not
working.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It seems that Elantech touchpad firmware version 2.34 on the Hercules eCAFÉ
suffers from a problem where bogus coordinates get reported at the beginning
of a touch action. This causes the mouse cursor or the scrolled page to
jump.
Included patch provides a workaround that discards mouse packets that are
likely to contain bogus coordinates. The workaround is activated when we
detect touchpad with fimware version 2.34.
Signed-off-by: Arjan Opmeer <arjan@opmeer.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
disable_irq() waits for all running handlers to complete before
returning. As such, if it's used to disable an interrupt from
that interrupt's handler it will deadlock. This replaces the
dangerous instances with the _nosync() variant which doesn't have
this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
disable_irq() waits for all running handlers to complete before
returning. As such, if it's used to disable an interrupt from
that interrupt's handler it will deadlock. This replaces the
dangerous instances with the _nosync() variant which doesn't have
this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
disable_irq() waits for all running handlers to complete before
returning. As such, if it's used to disable an interrupt from
that interrupt's handler it will deadlock. This replaces the
dangerous instances with the _nosync() variant which doesn't have
this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
disable_irq() waits for all running handlers to complete before
returning. As such, if it's used to disable an interrupt from
that interrupt's handler it will deadlock. This replaces the
dangerous instances with the _nosync() variant which doesn't have
this problem.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The use of disable_irq inside the handler for the interrupt being
disabled has always been dangerous. disable_irq should wait for that
handler to complete before returning -> deadlock.
For some reason this wasn't actually the case until 3aa551c9b was merged
but since this time, the ads7846 driver has deadlocked the system on
first interrupt.
Convert the driver to use the handler-safe _nosync variant.
Signed-off-by: Ben Nizette <bn@niasdigital.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The loop body was never executed, because the condition is
always false. Convert to for with more obvious condition.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
dev is leftover from b0ee0d3eb3
(Input: pc110pad - use no_pci_devices()).
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch removes depreciated IRQF_SAMPLE_RANDOM flags from
ad7877 and ad7879 touchscreen drivers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
PEN_{UP/DOWN} events are expected to be available soon after stopping
TSI auto measurement, but this is found not always be true. Work around
this by adding delay and simulating such an event (according to pen down
status bit).
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Bin did a lot of work on this driver, without his help, this driver
will not be possible.
Signed-off-by: Bin Yang <bin.yang@marvell.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The commit 6902c0bead that moved
driver registration out of kgameportd thread was incomplete and
did not add the code necessary to actually attach driver to
already registered devices, rectify that.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Fix this build error when CONFIG_SERIO is not set
hp_sdc_rtc.c:691: undefined reference to `hp_sdc_request_timer_irq'
and so on..
"select should be used with care. select will force
a symbol to a value without visiting the dependencies."
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The input core will add entropy to the pool so this flag is not
needed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Noises can be introduced when LCD signals are being driven, some platforms
provide a signal to assist the synchronization of this sampling procedure.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is no need to issue serialize_rcu() after adding a new handle
to the list of handles associated with the device because new events
will "see" the new handle in the list immediately. Remove it so we
can boot a little bit faster.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There are several DMI tables in the i8042 (keyboard) driver already, but
not one for the i8042.reset option. This patch adds such an option.
Two users for this table are added as well, the MSI Wind U-100 and the LG
X110. The MSI Wind also needs to be in the "don't trust the pnp data" for
the touchpad to work on my machine.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchpads don't reset right the first time (MSI Wind U-100 for
example). This patch will retry the reset up to 5 times.
In addition, on x86, we don't fail entire i8042 initialization if
controller reset fails in hope that keyboard port will still be
functional and user will still get a working keyboard. This is
especially important on netbooks.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: pci_slot: grab refcount on slot's bus
PCI Hotplug: acpiphp: grab refcount on p2p subordinate bus
PCI: allow PCI core hotplug to remove PCI root bus
PCI: Fix oops in pci_vpd_truncate
PCI: don't corrupt enable_cnt when doing manual resource alignment
PCI: annotate pci_rescan_bus as __ref, not __devinit
PCI-IOV: fix missing kernel-doc
PCI: Setup disabled bridges even if buses are added
PCI: SR-IOV quirk for Intel 82576 NIC
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
loop: mutex already unlocked in loop_clr_fd()
cfq-iosched: don't let idling interfere with plugging
block: remove unused REQ_UNPLUG
cfq-iosched: kill two unused cfqq flags
cfq-iosched: change dispatch logic to deal with single requests at the time
mflash: initial support
cciss: change to discover first memory BAR
cciss: kernel scan thread for MSA2012
cciss: fix residual count for block pc requests
block: fix inconsistency in I/O stat accounting code
block: elevator quiescing helpers
* 'i2c-for-2630-v2' of git://aeryn.fluff.org.uk/bjdooks/linux:
i2c: imx: Make disable_delay a per-device variable
i2c: xtensa s6000 i2c driver
powerpc/85xx: i2c-mpc: use new I2C bindings for the Socates board
i2c: i2c-mpc: make I2C bus speed configurable
i2c: i2c-mpc: use dev based printout function
i2c: i2c-mpc: various coding style fixes
i2c: imx: Add missing request_mem_region in probe()
i2c: i2c-s3c2410: Initialise Samsung I2C controller early
i2c-s3c2410: Simplify bus frequency calculation
i2c-s3c2410: sda_delay should be in ns, not clock ticks
i2c: iMX/MXC support
PCI parallel port devices can IRQ share so we should stop them hogging
the line and making a mess on modern PC systems. We know the sharing
side works as the PCMCIA driver has shared the parallel port IRQ for
some time.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here are some cleanups, mainly removing unused variables and silly
declarations.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Depend on KGDB_SERIAL_CONSOLE being set to N rather than !Y, since it can
be built as a module.
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Both software emulated and hardware based CTS and RTS are enabled in
serial driver.
The CTS RTS PIN connection on BF548 UART port is defined as a modem
device not as a host device. In order to test it under Linux, please
nake a cross UART cable to exchange CTS and RTS signal.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Only the CTS bit is affected.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
(akpm: queued pending confirmation of the new major number)
[randy.dunlap@oracle.com: select SERIAL_CORE]
Signed-off-by: Christian Pellegrin <chripell@fsfe.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Avoid using port->tty where possible (makes refcount fixing easier
later).
Remove unused code (the ioctl path is not used if the device has
mget/mset functions)
Remove various un-needed typecasts and long names so it could read it to
do the changes.
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use the new general RS485 Linux data structure (introduced by Alan with
commit number c26c56c0f4) in the Cris
architecture too (currently, Cris still uses the old private data
structure instead of the new one).
Signed-off-by: Claudio Scordino <claudio@evidence.eu.com>
Tested-by: Hinko Kocevar <hinko.kocevar@cetrtapot.si>
Tested-by: Janez Cufer <janez.cufer@cetrtapot.si>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_24BIT_MASK macro with DMA_BIT_MASK(24)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_28BIT_MASK macro with DMA_BIT_MASK(28)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_30BIT_MASK macro with DMA_BIT_MASK(30)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_31BIT_MASK macro with DMA_BIT_MASK(31)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_39BIT_MASK macro with DMA_BIT_MASK(39)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Replace all DMA_40BIT_MASK macro with DMA_BIT_MASK(40)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
