Commit Graph

56 Commits

Author SHA1 Message Date
Denis Cheng
922f9cfa79 fs/char_dev.c: chrdev_open marked static and removed from fs.h
There is an outdated comment in serial_core.c also fixed.

Signed-off-by: Denis Cheng <crquan@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-08 09:22:42 -08:00
Alan Cox
a46c999424 serial_core: bring mostly into line with coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-08 09:22:25 -08:00
Alan Cox
6d4d67beb9 serial: speed setup failure reporting
Invalid speeds are forced to 9600. Update the code for this to encode new
style baud rates properly.

Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 09:44:10 -08:00
Russell King
c8c6bfa39d serial: avoid stalling suspend if serial port won't drain
Some ports seem to be unable to drain their transmitters on shut down.  Such a
problem can occur if the port is programmed for hardware imposed flow control,
characters are in the FIFO but the CTS signal is inactive.

Normally, this isn't a problem because most places where we wait for the
transmitter to drain have a time-out.  However, there is no timeout in the
suspend path.

Give a port 30ms to drain; this is an arbitary value chosen to avoid long
delays if there are many such ports in the system, while giving a reasonable
chance for a single port to drain.  Should a port not drain within this
timeout, issue a warning.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 09:44:10 -08:00
Russell King
9d778a6937 serial: avoid waking up closed serial ports on resume
When we boot, serial ports remain in low power mode until they're used either
by userspace or for the kernel console.

However, if you suspend the system, and then resume, all serial ports will be
taken out of low power mode.  This is bad news for embedded devices where this
can mean higher power consumption.

Only bring a serial port out of low power mode if the port is being used as
the kernel console, or is in use by userspace.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 09:44:09 -08:00
Yinghai Lu
c3e4642be7 serial: keep the DTR setting for serial console.
with reverting "x86, serial: convert legacy COM ports to platform devices",
we will have the serial console before the port is probled again.

uart_add_one_port==>uart_configure_port==>set_mcttrl(port, 0) will clear
the DTR setting by uart_set_options().  then I will lose my output from
serial console again.

So try to keep DTR in uart_configure_port()

Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-02-05 09:44:09 -08:00
Alan Cox
149b36eae2 serial: stop passing NULL to functions that expect data
Earlier patches have removed the checking for old v new differences from the
USB drivers so we can now pass in a valid blank old termios so that we don't
to fill the drivers with magic hacks for console support

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-25 12:18:40 -07:00
Andres Salomon
8f4ce8c32f serial: turn serial console suspend a boot rather than compile time option
Currently, there's a CONFIG_DISABLE_CONSOLE_SUSPEND that allows one to stop
the serial console from being suspended when the rest of the machine goes
to sleep.  This is incredibly useful for debugging power management-related
things; however, having it as a compile-time option has proved to be
incredibly inconvenient for us (OLPC).  There are plenty of times that we
want serial console to not suspend, but for the most part we'd like serial
console to be suspended.

This drops CONFIG_DISABLE_CONSOLE_SUSPEND, and replaces it with a kernel
boot parameter (no_console_suspend).  By default, the serial console will
be suspended along with the rest of the system; by passing
'no_console_suspend' to the kernel during boot, serial console will remain
alive during suspend.

For now, this is pretty serial console specific; further fixes could be
applied to make this work for things like netconsole.

Signed-off-by: Andres Salomon <dilinger@debian.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-18 14:37:19 -07:00
Guennadi Liakhovetski
b3b708fa27 wake up from a serial port
Enable wakeup from serial ports, make it run-time configurable over sysfs,
e.g.,

echo enabled > /sys/devices/platform/serial8250.0/tty/ttyS0/power/wakeup

Requires

# CONFIG_SYSFS_DEPRECATED is not set

Following suggestions from Alan and Russell moved the may_wake_up checks
to serial_core.c. This time actually tested - it does even work. Could
someone, please, verify, that put_device after device_find_child is
correct?

Also would be nice to test with a Natsemi UART, that can wake up the system,
if such systems exist.

For this you just have to apply the patch below, issue the above "echo"
command to one of your Natsemi port, suspend and resume your system, and
verify that your Natsemi port still works.  If you are actually capable of
waking up the system from that port, would be nice to test that as well.

Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-10-16 09:42:50 -07:00
Russell King
97d97224ff [SERIAL] Fix console initialisation ordering
Ensure pm callback is called upon initialisation to place port in
correct power saving state.  Ensure console is initialised prior
to deciding whether to power down the port.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2007-10-15 18:53:35 +01:00
David Woodhouse
20620d688a serial: don't optimise away baud rate changes when BOTHER is used
The uart_set_termios() function will bail out early without bothering to
touch the hardware, if it decides that nothing "relevant" has changed.
Unfortunately, its idea of "relevant" doesn't include c_[io]speed.  So if
the baud rate bits are BOTHER and you just change the speed, the change
gets optimised away.

This patch makes it ignore the old Bfoo bits in c_cflag and just check
whether c_ispeed and c_ospeed have changed.  Those integers are always set
appropriately for us by set_termios().

Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-22 19:52:44 -07:00
Josh Boyer
4f640efb31 Use resource_size_t for serial port IO addresses
At present, various parts of the serial code use unsigned long to define
resource addresses.  This is a problem, because some 32-bit platforms have
physical addresses larger than 32-bits, and have mmio serial uarts located
above the 4GB point.

This patch changes the type of mapbase in both struct uart_port and struct
plat_serial8250_port to resource_size_t, which can be configured to be 64
bits on such platforms.  The mapbase in serial_struct can't safely be
changed, because that structure is user visible.

Signed-off-by: David Gibson <dwg@au1.ibm.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-24 12:24:58 -07:00
Yinghai Lu
79492689e4 serial: assert DTR for serial console devices
Some RS-232 devices require DTR to be asserted before they can be used.  DTR
is normally asserted in uart_startup() when the port is opened.  But we don't
actually open serial console ports, so assert DTR when the port is added.

BTW:
earlyprintk and early_uart are hard coded to set DTR/RTS.

rmk says

  The only issue I can think of is the possibility for an attached modem to
  auto-answer or maybe even auto-dial before the system is ready for it to do
  so.  Might have an undesirable cost implication for some running with such a
  setup.

  Apart from that, I can't think of any other side effect of this specific
  patch.

Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Gerd Hoffmann <kraxel@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-16 09:05:34 -07:00
Jiri Slaby
eb3a1e1145 Serial: serial_core, use pr_debug
serial_core, use pr_debug

Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07 12:12:51 -07:00
David Gibson
abb4a23907 serial: define FIXED_PORT flag for serial_core
At present, the serial core always allows setserial in userspace to change the
port address, irq and base clock of any serial port.  That makes sense for
legacy ISA ports, but not for (say) embedded ns16550 compatible serial ports
at peculiar addresses.  In these cases, the kernel code configuring the ports
must know exactly where they are, and their clocking arrangements (which can
be unusual on embedded boards).  It doesn't make sense for userspace to change
these settings.

Therefore, this patch defines a UPF_FIXED_PORT flag for the uart_port
structure.  If this flag is set when the serial port is configured, any
attempts to alter the port's type, io address, irq or base clock with
setserial are ignored.

In addition this patch uses the new flag for on-chip serial ports probed in
arch/powerpc/kernel/legacy_serial.c, and for other hard-wired serial ports
probed by drivers/serial/of_serial.c.

Signed-off-by: David Gibson <dwg@au1.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07 12:12:50 -07:00
Marc St-Jean
beab697ab4 serial driver PMC MSP71xx
Serial driver patch for the PMC-Sierra MSP71xx devices.

There are three different fixes:

1 Fix for DesignWare APB THRE errata: In brief, this is a non-standard
  16550 in that the THRE interrupt will not re-assert itself simply by
  disabling and re-enabling the THRI bit in the IER, it is only re-enabled
  if a character is actually sent out.

  It appears that the "8250-uart-backup-timer.patch" in the "mm" tree
  also fixes it so we have dropped our initial workaround.  This patch now
  needs to be applied on top of that "mm" patch.

2 Fix for Busy Detect on LCR write: The DesignWare APB UART has a feature
  which causes a new Busy Detect interrupt to be generated if it's busy
  when the LCR is written.  This fix saves the value of the LCR and
  rewrites it after clearing the interrupt.

3 Workaround for interrupt/data concurrency issue: The SoC needs to
  ensure that writes that can cause interrupts to be cleared reach the UART
  before returning from the ISR.  This fix reads a non-destructive register
  on the UART so the read transaction completion ensures the previously
  queued write transaction has also completed.

Signed-off-by: Marc St-Jean <Marc_St-Jean@pmc-sierra.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-07 12:12:50 -07:00
Burman Yan
8f31bb39ec [PATCH] serial: replace kmalloc+memset with kzalloc
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:52 -08:00
George G. Davis
3689a0ec60 [PATCH] serial: make sure UART is powered up when dumping MCTRL status
Since serial devices are powered down when not in use and some of those
devices cannot be accessed when powered down, we need to enable power
around calls to get_mcrtl() when dumping port state via uart_line_info().
This resolves hangs observed on some machines while reading serial device
registers when a port is powered off.

Signed-off-by: George G. Davis <gdavis@mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-02-14 08:09:52 -08:00
Alan Cox
606d099cdd [PATCH] tty: switch to ktermios
This is the grungy swap all the occurrences in the right places patch that
goes with the updates.  At this point we have the same functionality as
before (except that sgttyb() returns speeds not zero) and are ready to
begin turning new stuff on providing nobody reports lots of bugs

If you are a tty driver author converting an out of tree driver the only
impact should be termios->ktermios name changes for the speed/property
setting functions from your upper layers.

If you are implementing your own TCGETS function before then your driver
was broken already and its about to get a whole lot more painful for you so
please fix it 8)

Also fill in c_ispeed/ospeed on init for most devices, although the current
code will do this for you anyway but I'd like eventually to lose that extra
paranoia

[akpm@osdl.org: bluetooth fix]
[mp3@de.ibm.com: sclp fix]
[mp3@de.ibm.com: warning fix for tty3270]
[hugh@veritas.com: fix tty_ioctl powerpc build]
[jdike@addtoit.com: uml: fix ->set_termios declaration]
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Martin Peschke <mp3@de.ibm.com>
Acked-by: Peter Oberparleiter <oberpar@de.ibm.com>
Cc: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-12-08 08:28:57 -08:00
Linus Torvalds
6f3a28f7d1 Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial: (21 commits)
  [SERIAL] add PNP IDs for FPI based touchscreens
  [SERIAL] Magic SysRq SAK does nothing on serial consoles
  [SERIAL] tickle NMI watchdog on serial output.
  [SERIAL] Fix oops when removing suspended serial port
  [SERIAL] Fix resume handling bug
  [SERIAL] Remove wrong asm/serial.h inclusions
  [SERIAL] CONFIG_PM=n slim: drivers/serial/8250_pci.c
  [SERIAL] OMAP1510 serial fix for 115200 baud
  [SERIAL] returning proper error from serial core driver
  [SERIAL] Make uart_line_info() correctly tell MMIO from I/O port
  [SERIAL] suspend/resume handlers don't have level arg anymore
  [SERIAL] 8250 resourse management fixes
  [SERIAL] serial_cs: Add quirk for brainboxes 2-port RS232 card
  [SERIAL] serial_cs: handle Nokia multi->single port bodge via config quirk
  [SERIAL] serial_cs: add configuration quirk
  [SERIAL] serial_cs: Convert Oxford 950 / Possio GCC wakeup quirk
  [SERIAL] serial_cs: convert IBM post-init handling to a quirk
  [SERIAL] serial_cs: allow wildcarded quirks
  [SERIAL] serial_cs: convert multi-port table to quirk table
  [SERIAL] serial_cs: Use clean up multiport card detection
  ...
2006-10-03 09:13:29 -07:00
Jeff Dike
b68e31d0eb [PATCH] const struct tty_operations
As part of an SMP cleanliness pass over UML, I consted a bunch of
structures in order to not have to document their locking.  One of these
structures was a struct tty_operations.  In order to const it in UML
without introducing compiler complaints, the declaration of
tty_set_operations needs to be changed, and then all of its callers need to
be fixed.

This patch declares all struct tty_operations in the tree as const.  In all
cases, they are static and used only as input to tty_set_operations.  As an
extra check, I ran an i386 allyesconfig build which produced no extra
warnings.

53 drivers are affected.  I checked the history of a bunch of them, and in
most cases, there have been only a handful of maintenance changes in the
last six months.  serial_core.c was the busiest one that I looked at.

Signed-off-by: Jeff Dike <jdike@addtoit.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-02 07:57:14 -07:00
Russell King
a6b93a9085 [SERIAL] Fix oops when removing suspended serial port
A serial card might have been removed when the system is resumed.
This results in a suspended port being shut down, which results in
the ports shutdown method being called twice in a row.  This causes
BUGs.  Avoid this by tracking the suspended state separately from
the initialised state.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:17:40 +01:00
Ram Gupta
80e3c2b659 [SERIAL] returning proper error from serial core driver
Fix the issue of returning 0 even in case of error from uart_set_info
function.  Now it returns the error EBUSY when it can not set new port.

Signed-off-by: Ram Gupta <r.gupta@astronautics.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:07:00 +01:00
Sergei Shtylyov
6c6a2334a1 [SERIAL] Make uart_line_info() correctly tell MMIO from I/O port
/proc/tty/driver/serial incorrectly claims that UARTs having iotype of
UPIO_MEM32, UPIO_AU, or UPIO_TSI are I/O mapped.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-10-01 17:06:57 +01:00
Rafael J. Wysocki
e1da95ae38 [PATCH] suspend: make it possible to disable serial console suspend
Hack uart_suspend_port() and uart_resume_port() so that serial console
ports are not suspended if CONFIG_DISABLE_CONSOLE_SUSPEND is set.

This makes it possible to debug the suspend and resume routines of all
device drivers as well as the lowest-level swsusp code with the help of the
serial console.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-09-26 08:49:03 -07:00
Sergei Shtylyov
d21b55d30b [SERIAL] Make uart_match_port() work with all memory mapped UARTs
uart_match_port() always fails with UPIO_MEM32, UPIO_AU, and UPIO_TSI cases.
Since they match to the memory mapped UARTs, they should be handled just like
UPIO_MEM case.

Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-08-30 10:06:14 +01:00
Zang Roy-r61911
3be91ec738 [SERIAL] 8250: add tsi108 serial support
The following patch gets rid of CONFIG_TSI108_BRIDGE.  I add UPIO_TSI to
handle IIR and IER register in serial_in and serial_out.

(1) the reason to rewrite serial_in:

    TSI108 rev Z1 version ERRATA.  Reading the UART's Interrupt
    Identification Register (IIR) clears the Transmit Holding Register
    Empty (THRE) and Transmit buffer Empty (TEMP) interrupts even if they
    are not enabled in the Interrupt Enable Register (IER).  This leads to
    loss of the interrupts.  Interrupts are not cleared when reading UART
    registers as 32-bit word.

(2) the reason to rewrite serial_out:

    Check for UART_IER_UUE bit in the autoconfig routine.  This section
    of autoconfig is excluded for Tsi108/109 because bits 7 and 6 are
    reserved for internal use.  They are R/W bits.  In addition to
    incorrect identification, changing these bits (from 00) will make
    Tsi108/109 UART non-functional.

Signed-off-by: Roy Zang	<tie-fei.zang@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-09 21:11:09 +01:00
Linus Torvalds
075395d228 Merge branch 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-serial:
  [SERIAL] Ensure 8250_pci quirks are not marked __devinit
  [SERIAL] Convert fifosize to an unsigned int
2006-07-03 21:31:05 -07:00
Ingo Molnar
13e83599d2 [PATCH] lockdep: annotate serial
Teach special (dual-initialized) locking code to the lock validator.  Has no
effect on non-lockdep kernels.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-07-03 15:27:06 -07:00
Russell King
947deee890 [SERIAL] Convert fifosize to an unsigned int
Some UARTs have more than 255 bytes of FIFO, which can't be
represented by an unsigned char.  Change the kernel's internal
structure to be an unsigned int, but still export an unsigned char
via the TIOCGSERIAL ioctl.  If the TIOCSSERIAL ioctl provides a
fifo size of 0, assume this means "don't change" otherwise we'll
corrupt the larger fifo sizes.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-07-02 20:45:51 +01:00
Jörn Engel
6ab3d5624e Remove obsolete #include <linux/config.h>
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-06-30 19:25:36 +02:00
Greg Kroah-Hartman
331b831983 [PATCH] devfs: Rename TTY_DRIVER_NO_DEVFS to TTY_DRIVER_DYNAMIC_DEV
I've always found this flag confusing.  Now that devfs is no longer around, it
has been renamed, and the documentation for when this flag should be used has
been updated.

Also fixes all drivers that use this flag.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:09 -07:00
Greg Kroah-Hartman
aa4148cfc7 [PATCH] devfs: Remove devfs support from the serial subsystem
Also fixes all serial drivers.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-06-26 12:25:05 -07:00
Andrew Victor
1281e36027 [ARM] 3523/1: Serial core pm_state
Patch from Andrew Victor

The serial_core already manages the power state of the UARTs, and
therefore it shouldn't suspend a UART which was previously suspended.

This patch modifies serial_core only call the UART-specific
power-management function if the PM state is actually changing.

Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-05-16 11:28:49 +01:00
Russell King
68ac64cd3f [SERIAL] Clean up serial locking when obtaining a reference to a port
The locking for the uart_port is over complicated, and can be
simplified if we introduce a flag to indicate that a port is "dead"
and will be removed.

This also helps the validator because it removes a case of non-nested
unlock ordering.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
2006-04-30 11:13:50 +01:00
Russell King
d358788f3f [SERIAL] kernel console should send CRLF not LFCR
Glen Turner reported that writing LFCR rather than the more
traditional CRLF causes issues with some terminals.

Since this aflicts many serial drivers, extract the common code
to a library function (uart_console_write) and arrange for each
driver to supply a "putchar" function.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-03-20 20:00:09 +00:00
Pavel Machek
d5f735e52f [PATCH] serial core: work around sub-driver bugs
We're presently getting oopses because Bluetooth (and possibly other) drivers
are calling core functions after things have been shut down.

So rather than oopsing, let's drop a warning then take avoiding action, so the
machine survives.  Once all the sub-drivers are fixed up we can remove the
take-avoiding-action part.

Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-08 14:14:00 -08:00
Atsushi Nemoto
9c0f4755bd [SERIAL] initialize spinlock for port failed to setup console
It seems serial_core intend to initialize port->lock just once for each
ports.  This is done in uart_set_options() for console, and in
uart_add_one_port() for other ports.  But there is a case the port->lock is
not initialized by serial_core.  If the setup function for the console was
failed, it will not call uart_set_options() but the port is marked as
console (uart_console(port) returns 1).  It can happen if console was PCI
port which can not detected at the time of register_console.

This patch is to initialize port->lock for such console port.  With this
change, most of spin_lock_init() (some of them are labeled "Temporary
fix.") in low-level serial drivers can be omitted.

Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-02-02 20:53:39 +00:00
Russell King
0077d45e46 [SERIAL] Make uart_port flags a bitwise type
Same reasoning as commit 747c8a5594
but this time we're making uart_port flags a bitwise type - not
all of these flags correspond with the old ASYNC_ flags, so there
is the possibility for bugs if the wrong ASYNC_* constants are
used.  Always use UPF_* constants for uart_port->flags.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-21 23:03:28 +00:00
Russell King
ba899dbc03 [SERIAL] Make port->ops constant
No one should write to the port->ops structure, so make it constant.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-21 22:45:50 +00:00
Ingo Molnar
e2862f6a83 [SERIAL] convert uart_state.sem to uart_state.mutex
semaphore to mutex conversion.

the conversion was generated via scripts, and the result was validated
automatically via a script as well.

build and boot tested.

Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-13 21:37:07 +00:00
Arjan van de Ven
f392ecfa12 [SERIAL] turn serial semaphores into mutexes
Turn several drivers/serial/ semaphores-used-as-mutex into mutexes

Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-12 18:44:32 +00:00
Russell King
f61051cd2f [SERIAL] Fix clocal wakeup problem
Jim Alexander reported a problem where "if one calls open() in
blocking mode with CLOCAL off, the 8250.c driver under the 2.6
kernel (or at least 2.6.8 and 2.6.10) does not wake up the
blocked process when DCD is asserted."

Fix this by enabling modem status interrupts immediately before
we read the carrier detect status.

Thanks to Jim for reporting the problem and testing the fix.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-07 23:11:23 +00:00
Benjamin Herrenschmidt
1624f00334 [SERIAL] Fix matching of MMIO ports
The function uart_match_port() incorrectly compares the ioremap'd
virtual addresses of ports instead of the physical address to find
duplicate ports for MMIO based UARTs. This fixes it.

Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2006-01-04 18:09:44 +00:00
Arjan van de Ven
cb3592be27 [SERIAL] mark several serial tables const
This patch marks a few serial data structures const, moving them to
.rodata where they won't false-share cachelines with things that get
written to.

Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-11-28 21:04:11 +00:00
Russell King
ee31b33785 [SERIAL] Fix Bug 4900: S3 resume oops with irattach - Thinkpad A21m
If we fail to re-startup a serial port on resume, shut it down
immediately and mark it as an error condition.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-11-13 15:28:51 +00:00
Pantelis Antoniou
21c614a789 [SERIAL] Support Au1x00 8250 UARTs using the generic 8250 driver.
The offsets of the registers are in a different place, and
some parts cannot handle a full set of modem control signals.

Signed-off-by: Pantelis Antoniou <pantelis@embeddedalley.ocm>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-11-06 09:07:03 +00:00
Russell King
0cf669d5c5 [SERIAL] Arrange better identification of ports
Folk seem to get confused when they see two or more ttyS0 ports
appearing at boot time.  One comes from the legacy table, and
one from PNP.

Hence, display the bus ID of the device which supplied the port.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-10-31 11:42:22 +00:00
Jayachandran C
a2436b22de [SERIAL] remove unneeded code from serial_core.c
This patch fixes an issue reported by Coverity in serial/serial_core.c

Error reported: Variable "&((info)->tty)->flags" tracked as NULL was passed to a
function that dereferences it.

The later statements in the function assumes 'info->tty != NULL', so this
check is not necessary.  Probably a 'BUG_ON(info->tty == NULL)' can be added.

Signed-off-by: Jayachandran C. <c.jayachandran at gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-10-30 23:26:16 +00:00
Russell King
30b7a3bc13 [SERIAL] Prefix serial printks with KERN_INFO and pre-format
Pre-format the IO part of the ttyS printks, and prefix them with
KERN_INFO to avoid bootsplash corruption.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2005-09-03 15:30:21 +01:00