This patch modifies ubi_wl_flush to force the erasure of
particular volume id / logical eraseblock number pairs. Previous functionality
is preserved when passing UBI_ALL for both values. The locations where ubi_wl_flush
were called are appropriately changed: ubi_leb_erase only flushes for the
erased LEB, and ubi_create_volume forces only flushing for its volume id.
External code can call this new feature via the new function ubi_flush() added
to kapi.c, which simply passes through to ubi_wl_flush().
This was tested by disabling the call to do_work in ubi thread, which results
in the work queue remaining unless explicitly called to remove. UBIFS was
changed to call ubifs_leb_change 50 times for four different LEBs. Then the
new function was called to clear the queue: passing wrong volume ids / lnum,
correct ones, and finally UBI_ALL for both to ensure it was finally all
cleard. The work queue was dumped each time and the selective removal
of the particular LEB numbers was observed. Extra checks were enabled and
ubifs's integck was also run. Finally, the drive was repeatedly filled and
emptied to ensure that the queue was cleared normally.
Artem: amended the patch.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Joel will use it in his 'ubi_flush()' extention to specify all eraseblocks.
Also amend the comment for UBI_UNKNOWN - it is used beyond attaching info
structure now.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This is part of a multipart patch to allow UBI to force the erasure of
particular logical eraseblock numbers. In this patch, the volume id and LEB
number are added to ubi_work data structure, and both are also passed as a
parameter to schedule erase to set it appropriately. Whenever ubi_wl_put_peb
is called, the lnum is also passed to be forwarded to schedule erase. Later,
a new ubi_sync_lnum will be added to execute immediately all work related to
that lnum.
This was tested by outputting the vol_id and lnum during the schedule of
erasure. The ubi thread was disabled and two ubifs drives on separate
partitions repeated changed a small number of LEBs. The ubi module was readded,
and all the erased LEBs, corresponding to the volumes, were added to the
schedule erase queue.
Artem: minor tweaks
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch adds the volume id to struct ubi_ainf_peb when scanning the LEBs at
startup. PEBs now added to the erase queue will know their original LEB number
and volume id, if available, and will be -1 otherwise (for instance, if the VID
header is unreadable).
This was tested by creating an ubi device with 3 volumes and disabiling the
ubi_thread's do_work functionality. The different ubi volumes were formatted
to ubifs and had files created and erased. The ubi modules was reloaded and
the list of LEB's added to the erased list was outputted, confirming the
volume ids and LEB numbers were appropriate.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Explicitly provide the first internal volume ID value in the comment for
UBI_INTERNAL_VOL_START. This allows developers who, when adding features
related to volume ids and observe unexpected very large volume ids, to grep
for the observed value in the source code and find out immediately that it is
expected behaviour.
Signed-off-by: Joel Reardon <reardonj@inf.ethz.ch>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Finally, rename the scan.c file. Now adding fastmap support won't look that
hacky anymore.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This file is small and it does not make sense to have it separate from where
everything else lives, so merge it with ubi.h.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Rename the constant to UBI_UNKNOWN, for the same reason that we are going
to add nother attaching method and re-use the same data structures, so the
"SCAN" in the name becomes incorrect. I've also removed the "_EC" part because
Joel is going to use this constant for other fields in the attaching info data
structures.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Rename the 'attach_by_scanning()' function to 'ubi_attach()' and move it to
scan.c. Richard will plug his fastmap stuff there.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have a couple of initialization funcntionsn left which have "_scan" suffic -
rename them:
ubi_eba_init_scan() -> ubi_eba_init()
ubi_wl_init_scan() -> ubi_wl_init()
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch amends commentaries in scan.[ch] to match the new logic. Reminder -
we did the restructuring to prepare the code for adding the fastmap. This patch
also renames a couple of functions - it was too difficult to separate out that
change and I decided that it is not too bad to have it in the same patch with
commentaries changes.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
The 'ubi_scan_erase_peb()' is used only in scan.c so can be static. Also
re-name it to 'early_erase_peb()' because we tend to use "ubi_" prefix only for
non-static fuction and also because the new name is better.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
After re-naming the 'struct ubi_scan_volume' we should adjust all variables
named 'sv' to something else, because 'sv' stands for "scanning volume".
Let's rename it to 'av' which stands for "attaching volume" which is
a bit more consistent and has the same length, which makes re-naming easy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
After re-naming the 'struct ubi_scan_info' we should adjust all variables
named 'si' to something else, because 'si' stands for "scanning info".
Let's rename it to 'ai' which stands for "attaching info" which is
a bit more consistent and has the same length, which makes re-naming easy.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
After re-naming the 'struct ubi_scan_leb' we should adjust all variables
named 'seb' to something else, because 'seb' stands for "scanning eraseblock".
Let's rename it to 'aeb' which stands for "attaching eraseblock" which is
a bit more consistend and has the same length.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Now some commentaries are out-of-date, after we re-named the data
structures - amend them.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Rename 'struct ubi_scan_info' to 'struct ubi_attach_info'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Rename 'struct ubi_scan_volume' to 'struct ubi_ainf_volume'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word and use "ainf" instead which stands
for "attach information". It has the same length as "scan" so re-naming
is trivial.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Rename 'struct ubi_scan_leb' to 'struct ubi_ainf_leb'. This is part
of the code re-structuring I am trying to do in order to add fastmap
in a more logical way. Fastmap can share a lot with scanning, including
the attach-time data structures, which all now have "scan" word in the
name. Let's get rid of this word and use "ainf" instead which stands
for "attach information". It has the same length as "scan" so re-naming
is trivial.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
This patch removes the 'dbg_err()' macro and we now use 'ubi_err' instead.
The idea of 'dbg_err()' was to compile out some error message to make the
binary a bit smaller - but I think it was a bad idea.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have the "sefl-check" feature in UBI, but for historical reasons many
corresponding functions and commentaries in the code use term "paranoid check"
instead. Let's clean this up and use "self-check" everywhere.
This patch renames functions, amends messages and kills several redundant
debugging messages.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We have the "sefl-check" feature in UBI, but for historical reasons many
corresponding functions and commentaries in the code use term "paranoid check"
instead. Let's clean this up and use "self-check" everywhere.
This patch renames functions, amends comments and messages. It touches only the
io.c file.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
This patch kills the UBI debugging Kconfig option completely and makes all the
debugging stuff to be always compiled-in. It was pain in the neck to maintain
this useless option because all users I am aware of have debugging enabled
anyway - how else will you diagnose errors otherwise?
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_mkvol_req()' to 'ubi_dump_mkvol_req()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_seb()' to 'ubi_dump_seb()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_sv()' to 'ubi_dump_sv()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_vtbl_record()' to 'ubi_dump_vtbl_record()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
I am going to remove the "UBI debugging" compilation option and make the
debugging stuff to be always compiled it. This patch is a preparation
which renames 'ubi_dbg_dump_vol_info()' to 'ubi_dump_vol_info()'.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Richard removed the "dtype" hint, but few commentaries were left and this patch
removes them. I've also added a better description about the "dtype" field in
the ubi-user.h for people who may ever wonder what was that dtype thing about.
This patch also adds an important note that it is better to use value "3" for
the "dtype" field.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
We do not need this feature and to our shame it even was not working
and there was a bug found very recently.
-- Artem Bityutskiy
Without the data type hint UBI2 (fastmap) will be easier to implement.
Signed-off-by: Richard Weinberger <richard@nod.at>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Currently UBI silently retries I/O operation in case of errors. This patch
makes it emit a warning before retrying. This should allow users notice issues
earlier.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI (and UBIFS) are a bit over-engineered WRT debugging. The idea was to
link as few as possible when debugging is disabled, but the downside is
that most people produce bug reports which are difficult to understand.
Always dump the VID and EC headers' contents in case of errors when it
is helpful.
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
UBI (and UBIFS) are a bit over-engineered WRT debugging. The idea was to
link as few as possible when debugging is disabled, but the downside is
that most people produce bug reports which are difficult to understand.
Always dump the flash contents in case of errors, not only when debugging is
enabled.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
UBI (and UBIFS) are a bit over-engineered WRT debugging. The idea was to
link as few as possible when debugging is disabled, but the downside is
that most people produce bug reports which are difficult to understand.
This patch weeds out the 'ubi_dbg_dump_stack()' function and turns it
into 'dump_stack()' - it is always useful to have stack dump in case of
an error.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Fix following compile error caused by commit 39febc0 (mtd: nand: gpmi:
adopt pinctrl support).
CC drivers/mtd/nand/gpmi-nand/gpmi-nand.o
drivers/mtd/nand/gpmi-nand/gpmi-nand.c: In function ‘acquire_resources’:
drivers/mtd/nand/gpmi-nand/gpmi-nand.c:499:45: error: ‘pdev’ undeclared (first use in this function)
Reported-by: Subodh Nijsure <snijsure@grid-net.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
* 'clk-next' of git://git.linaro.org/people/mturquette/linux:
clk: Fix CLK_SET_RATE_GATE flag validation in clk_set_rate().
clk: Provide dummy clk_unregister()
ARM: Kirkwood: Replace clock gating
ARM: Orion: Audio: Add clk/clkdev support
ARM: Orion: PCIE: Add support for clk
ARM: Orion: XOR: Add support for clk
ARM: Orion: CESA: Add support for clk
ARM: Orion: SDIO: Add support for clk.
ARM: Orion: NAND: Add support for clk, if there is one.
ARM: Orion: EHCI: Add support for enabling clocks
ARM: Orion: SATA: Add per channel clk/clkdev support.
ARM: Orion: UART: Get the clock rate via clk_get_rate().
ARM: Orion: WDT: Add clk/clkdev support
ARM: Orion: Eth: Add clk/clkdev support.
ARM: Orion: SPI: Add clk/clkdev support.
ARM: Orion: Add clocks using the generic clk infrastructure.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Allow a NAND chip using the orion_nand driver to be described using devicetree.
Changes since last submission (V4) [Addressing comments by]:-
* WARN when bank-width is out of range [Andrew Lunn]
Changes since last submission (V3):-
* Document all parameters [Grant Likely]
* Convert bank-width to be in bytes
* Add explicit defaults for cle, ale and bank-width
Signed-off-by: Jamie Lentin <jm@lentin.co.uk>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
drivers/mmc/host/sdhci-esdhc-imx.c
drivers/net/ethernet/freescale/fec.c
drivers/spi/spi-imx.c
drivers/tty/serial/imx.c
This resolves dependencies between the pinctrl and clock changes
in imx.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Spansion S29NS512P flash uses a 16bit transfer to report number
of sectors instead of two 8bit accesses as CFI specifies.
Artem: remove warning message which said that we are applying the
fixup - no need to scary the user unnecessarily.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Two modes are supported: 4-bit and 8-bit error correction.
Note that 4-bit mode is only confirmed to work on OMAP3630 ES 1.x,
x >= 1. The OMAP3 GPMC hardware BCH engine computes remainder
polynomials, it does not provide automatic error location and
correction: this step is implemented using the BCH library.
This implementation only protects page data, there is no support
for protecting user-defined spare area bytes (this could be added
with few modifications); therefore, it cannot be used with YAFFS2
or other similar filesystems that depend on oob storage.
Before being stored to nand flash, hardware BCH ecc is adjusted
so that an erased page has a valid ecc; thus allowing correction of
bitflips in blank pages (also common on 4-bit devices).
BCH correction mode is selected at runtime by setting platform data
parameter 'ecc_opt' to value OMAP_ECC_BCH4_CODE_HW or
OMAP_ECC_BCH8_CODE_HW.
This code has been tested with mtd test modules, UBI and UBIFS on a
BeagleBoard revC3 (OMAP3530 ES3.0 + Micron NAND 256MiB 1,8V 16-bit).
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Apparently, there is an implementor of 'read_oob' which may return an
error inidication (e.g. docg4_read_oob may return -EIO).
Test the return value of 'read_oob/read_oob_raw', and if negative,
propagate the error, so it's returned by the '_read_oob' interface.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
As of [mtd: nand: remove autoincrement 'sndcmd' code], the
NAND_CMD_READ0 command is issued unconditionally.
Thus, read_oob/read_oob_raw's 'sndcmd' argument is no longer needed, as
well as their return code.
Remove the 'sndcmd' parameter, and set the return code to 0.
Signed-off-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Winbond W25Q80BW is a 8Mbit serial flash memory device.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch just adds the DT support to gpmi-nand.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Huang Shijie <shijie8@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read/write OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller didn't request it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Don't read OOB if the caller doesn't require it.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
We now have an interface for notifying the nand_ecc_ctrl functions when OOB
data must be returned to the upper layers and when it may be left untouched.
This patch fills in the 'oob_required' parameter properly from
nand_do_{read,write}_ops. When utilized properly in the lower layers, this
parameter can improve performance and/or reduce complexity for NAND HW and SW
that can simply avoid transferring the OOB data.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New NAND controllers can perform read/write via HW engines which don't expose
OOB data in their DMA mode. To reflect this, we should rework the nand_chip /
nand_ecc_ctrl interfaces that assume that drivers will always read/write OOB
data in the nand_chip.oob_poi buffer. A better interface includes a boolean
argument that explicitly tells the callee when OOB data is requested by the
calling layer (for reading/writing to/from nand_chip.oob_poi).
This patch adds the 'oob_required' parameter to each relevant {read,write}_page
interface; all 'oob_required' parameters are left unused for now. The next
patch will set the parameter properly in the nand_base.c callers, and follow-up
patches will make use of 'oob_required' in some of the callee functions.
Note that currently, there is no harm in ignoring the 'oob_required' parameter
and *always* utilizing nand_chip.oob_poi, but there can be
performance/complexity/design benefits from avoiding filling oob_poi in the
common case. I will try to implement this for some drivers which can be ported
easily.
Note: I couldn't compile-test all of these easily, as some had ARCH
dependencies.
[dwmw2: Merge later 1/0 vs. true/false cleanup]
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Shmulik Ladkani <shmulik.ladkani@gmail.com>
Acked-by: Jiandong Zheng <jdzheng@broadcom.com>
Acked-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Lantiq SoCs have a External Bus Unit (EBU) that is used to attach MTD media.
As we need to co-exist with PCI on the same bus, certain swapping settings must
be applied. Similar to the NOR map driver we need to apply a fix to make NAND
work. The easiest way is to use byte reads.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch sets the of_match_table field inside plat_nand's platform_driver.
We also add a struct mtd_part_parser_data pointer to make sure of_part parsing
works.
If an arch wants to support plat_nand via DT it needs to setup the
platform_nand_data and hook it into the platform_device.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Add the id and sector mappings for mx25l2005a flash chips.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
No drivers use auto-increment NAND, so kill the NO_AUTOINCR option entirely.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND_NO_AUTOINCR option is always set, so we will kill the option and make
"no autoincrement" the default behavior for nand_base.c. Thus, we should remove
the code which decides whether or not to send the NAND_CMD_READ0 command.
Instead, we unconditionally send the command.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The NAND layer always has NAND_NO_AUTOINCR set, so we will never utilize the
AUTOINCR code in nandsim. We will be removing the NAND_NO_AUTOINCR option soon,
and so kill this code as well.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The drivers' _read() method, absent an error, returns a non-negative integer
indicating the maximum number of bit errors that were corrected in any one
region comprising an ecc step. MTD returns -EUCLEAN if this is >=
bitflip_threshold, 0 otherwise. If bitflip_threshold is zero, the comparison is
not made since these devices lack ECC and always return zero in the non-error
case (thanks Brian)¹. Note that this is a subtle change to the driver
interface.
This and the preceding patches in this set were tested with ubi on top of the
nandsim and docg4 devices, running the ubi test io_basic from mtd-utils.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040468.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This patch adds sanity checks that ensure that drivers for controllers with
hardware ECC set the 'strength' element in struct nand_ecc_ctrl. Also stylistic
changes to the line that calculates strength for software ECC.
This v2 simplifies the check. Thanks Brian!¹
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040890.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The ecc.read_page() method for nand drivers is changed to return the maximum
number of bitflips that were corrected on any one region covering an ecc step,
This patch doesn't change what the nand code returns to mtd.
This v2 includes the change to the fsl_ifc_nand driver requested by Scott¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040883.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Acked-by (freescale changes): Scott Wood <scottwood@freescale.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
An element 'bitflip_threshold' is added to struct mtd_info, and also exposed as
a read/write variable in sysfs. This will be used to determine whether or not
mtd_read() returns -EUCLEAN or 0 (absent a hard error). If the driver leaves it
as zero, mtd will set it to a default value of ecc_strength.
This v2 adds the line that propagates bitflip_threshold from the master to the
partitions - thanks Ivan¹.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-April/040900.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ecc_strength element of struct mtd_info is exposed as a read-only variable in
sysfs.
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This fixes a couple of ecc strength values for which I earlier made conservative
guesses, but whose correct values were later determined¹ (thanks Ivan). Also
sets strength for fsl_ifc_nand, which was merged to mainline after the original
patch that set the strength for all drivers.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040325.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
ecc_strength element of mtd_info will be the strength of one ecc step, not of
the entire writesize, as was previously planned. This is the appropriate way
because, as was pointed out¹, bit errors in excess of the strength of one
step can cause a hard error if they all occur within the same ecc region.
¹ http://lists.infradead.org/pipermail/linux-mtd/2012-March/040313.html
Signed-off-by: Mike Dunn <mikedunn@newsguy.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
To make sure the NAND chip is properly programmed we need a status
command before each page write. When CONFIG_MTD_NAND_VERIFY_WRITE=y this
assumption is broken when writing multiple pages consecutively. This
patch fixes this.
Signed-off-by: Bastian Hecht <hechtb@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This is tested on i.MX27.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This gets rid of one more nfc_is_vX().
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This commit makes problems on v1 and v2 regarding 4KiBpages more obvious.
As I don't have a 4KiB flash handy I just keep the status quo.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This gets rid of several instances of cpu_is_mx21() in the driver.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
page_read() never returns NULL, so we can remove the NULL check here.
Signed-off-by: Ryosuke Saito <raitosyo@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The original Broadcom partition order has the root fs in front of the
kernel, which resulted in miscalculated partition sizes.
Detect when such an image is on the flash and also reorder the partitions
accordingly.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If a context switch occurs in function omap_wait() just before the
while loop is entered, then upon return from context switch the
timeout may already have elapsed: in that case, status is never
read from NAND device, and omap_wait() returns an error.
This failure has been experimentally observed during stress tests.
This patch ensures a NAND status read is always performed before
returning, as in the generic nand_wait() function.
Signed-off-by: Ivan Djelic <ivan.djelic@parrot.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
clk_{un}prepare is mandatory for platforms using common clock framework. Since
this driver is used by SPEAr platform, which supports common clock framework,
add clk_{un}prepare() support for it.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
scb2_flash.c is a PCI driver, but its build fails when CONFIG_PCI
is not enabled, so make it depend on PCI.
drivers/mtd/maps/scb2_flash.c:237:1: warning: data definition has no type or storage class
drivers/mtd/maps/scb2_flash.c:237:1: warning: type defaults to 'int' in declaration of 'module_pci_driver'
drivers/mtd/maps/scb2_flash.c:237:1: warning: parameter names (without types) in function declaration
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
If prefetch engine is busy, current code "forgets" to call
dma_unmap_single(), which results in a deadlock later, so add it.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Some not-supported nand chips may pass the current parsing code,
and get the wrong page size and oob size. Sometimes, it's hard to notice
that you get the wrong values, because there is no warning or error.
So it's useful to print out the page size and oob size in the end of
the parsing function. We can check these values with the datasheet of the nand
chip as soon as possible.
Artem: amend the print a bit
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
