USB1 can change to host/function by checking PTB3.
This patch add USB1 gadget support and check PTB3 when boot,
and change name to usb1_common_XXX from usb1_host_XXX.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the ms7724se board code to pass the mac
address to the sh_eth driver using platform data.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The vast majority of SH platforms want this, and the few that don't
aren't going to care one way or the other. Enable it across the board.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this was tacked on to the dma debug init bits from
fs_initcall(), which is far too late for devices setting up their own
per-device coherent areas.
Throw this in the beginning of mem_init(), as per the x86 iommu
allocation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many of these symbols went away completely, or we just never cared about
them in the first place. Trim the exports down to the essential set.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
These were previously hidden in sh_ksyms_32, despite also being needed
for sh64 now that the cache.c code is shared.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that this contains a grand total of 1 Kconfig option, it's hardly
worth keeping split out. Roll CONFIG_PCI back in to the top-level
architecture Kconfig, along with the other bus types.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Leaving this configurable caused more trouble than it was ever worth, so
just make it explicit. Boards that are verified one way or the other can
fix up their selects accordingly. We presently default to non-coherent
for most platforms.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that SH's irqflags functions are out of line it becomes necessary to
mark them as "notrace" so that we don't try to trace them.
[ Do the same for irq_64.c -- PFM. ]
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The hugetlb dependencies presently depend on SUPERH && MMU while the
hugetlb page size definitions depend on CPU_SH4 or CPU_SH5. This
unfortunately allows SH-3 + MMU configurations to enable hugetlbfs
without a corresponding HPAGE_SHIFT definition, resulting in the build
blowing up.
As SH-3 doesn't support variable page sizes, we tighten up the
dependenies a bit to prevent hugetlbfs from being enabled. These days
we also have a shiny new SYS_SUPPORTS_HUGETLBFS, so switch to using
that rather than adding to the list of corner cases in fs/Kconfig.
Reported-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the ecovec24 board code to pass the mac
address to the sh_eth driver using platform data.
Also, remove the static clock to allow Runtime PM.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add HWBLK_ETHER to the sh_eth platform device
to allow Runtime PM of the ethernet hardware.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add an uImage.bin target to allow uncompressed uImages.
Useful for boards with busted u-boot decompression like
the rsk7203 on my desk.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This unbreaks kexec support. Without this fix all
cases of kexec fails since __pa() does not behave
like PHYSADDR(). The downside is that we also kill
the code blocking users running old kexec-tools.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SD Card support to the kfr2r09 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and yc304.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add SD Card support to the se7724 board using the
sh_mobile_sdhi driver hooked up to SDHI0 and CN7.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the AP325 board to use sh_mobile_sdhi for the
SD Card connected to CN3 instead of mmc_spi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board to use sh_mobile_sdhi for the
SD Card connected to CN9 instead of mmc_spi.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When CONFIG_FUNCTION_GRAPH_TRACER is enabled the function graph tracer
may patch return addresses on the stack with the address of
return_to_handler(). This really confuses the DWARF unwinder because it
will try find the caller of return_to_handler(), not the caller of the
real return address.
So teach the DWARF unwinder how to find the real return address whenever
it encounters return_to_handler().
This patch does not cope very well when multiple return addresses on the
stack have been patched. To make it work properly it would require state
to track how many return_to_handler()'s have been seen so that we'd know
where to look in current->curr_ret_stack[]. So for now, instead of
trying to handle this, just moan if more than one return address on the
stack has been patched.
Signed-off-by: Matt Fleming <matt@console-pimps.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds an __irq_entry annotation for do_IRQ() so that the IRQ
annotation in the function graph tracer works as advertized. We already
have the IRQENTRY section wired up, so this is just a trivial addition
to actually make use of it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves the current dma_alloc/free_coherent() calls to a generic
variant and plugs them in for the nommu default. Other variants can
override the defaults in the dma mapping ops directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the past these were simply wrapping to barrier() which was sufficient
on SH SMP platforms predating SH-4A. Unfortunately due to ll/sc semantics
an explicit synco is needed in these cases, which is sorted for us by
just switching these over to smp_mb(). smp_mb() also has the benefit of
being wrapped to barrier() in the UP and non-SH4A cases, so old behaviour
is maintained for those parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SCIF2 and the FPU exceptions happen to share vector numbers, one in
EXPEVT and the other in INTEVT. This is a violation of the interface and
should have never made it in to silicon. On top of that, the demux hack
that was added for special dispatch is rather error prone, and introduces
more problems than it solves. Kill all of it off, and just refuse to deal
with SCIF2 outright.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This simplifies the irqflags support by switching over to the asm-generic
version. The necessary support functions are brought out-of-line for both
SHcompact and SHmedia instruction sets.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This code was added for some ancient SH-4 solution engines with peculiar
boot ROMs that did silly things to the UBC MSTP bits. None of these have
been in the wild for years, and these days the clock framework wraps up
the MSTP bits, meaning that the UBC code is one of the few interfaces
that is stomping MSTP bits underneath the clock framework. At this point
the risks far outweigh any benefit this code provided, so just kill it
off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables SCHED_MC support for SH-X3 multi-cores. Presently this is
just a simple wrapper around the possible map, but this allows for
tying in support for some of the more exotic NUMA clusters where we can
actually do something with the topology.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
In the case where need_resched() is set in between the cpu_idle() and
pm_idle() calls we were missing an else case for just re-enabling local
IRQs and bailing out. This was noticed by the irqs_disabled() warning,
even though IRQs were being re-enabled elsewhere.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the x86 change and moves check_pgt_cache() up under the
!need_resched() tight loop, rather than simply calling in to it when
exiting idle.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This does a bit of chainsawing of the idle loop code to get light sleep
working on SMP. Previously this was forcing secondary CPUs in to sleep
mode with them not coming back if they didn't have their own local
timers. Given that we use clockevents broadcasting by default, the CPU
managing the clockevents can't have IRQs disabled before entering its
sleep state.
This unfortunately leaves us with the age-old need_resched() race in
between local_irq_enable() and cpu_sleep(), but at present this is
unavoidable. After some more experimentation it may be possible to layer
on SR.BL bit manipulation over top of this scheme to inhibit the race
condition, but given the current potential for missing wakeups, this is
left as a future exercise.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the secondary CPUs are forced in to light sleep mode, but we were
missing the same initialization for the boot CPU. This resulted in
inconsistent sleep modes depending on which CPU we were on, confusing the
idle loop when not polling.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The open function got the BKL via the big push down. Replace it by
preempt_enable/disable as this is sufficient for an UP machine.
The ioctl can be unlocked because there is no functionality which
requires serialization. The usage by multiple callers is broken with
and without the BKL due to the local static variable addr.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add code to handle the cache disabled case. Fixes breakage introduced by
37443ef3f0 ("sh: Migrate SH-4 cacheflush
ops to function pointers."). Without this patch configuring caches off
with CONFIG_CACHE_OFF=y makes kfr2r09 and migo-r lock up in fbdev
deferred io or early user space.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently The SH-4 cache flushing code uses flush_cache_4096() for most
of the real flushing work, which breaks down to a fixed 4096 unroll and
increment. Not only is this sub-optimal for larger page sizes, it's also
uncovered a bug in sh4_flush_dcache_page() when large page sizes are used
and we have no cache aliases -- resulting in only a part of the page's
D-cache lines being written back.
Signed-off-by: Valentin Sitdikov <valentin.sitdikov@siemens.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
