More cosmetic cleanups prior to the interrupt/error handling logic changes.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
The drive is directly soldered to the controller, so there is no cable at
all. Remove the 40-wire assumption so the drive can operate at max speed.
Before patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 5.29612 s, 25.3 MB/s
After patch:
$ dd if=/dev/sda of=/dev/null bs=2M count=64 iflag=direct
134217728 bytes (134 MB) copied, 3.94955 s, 34.0 MB/s
Signed-off-by: Dan McGee <dpmcgee@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix mis-reporting of NCQ errors by ensuring that result_tf->flags
is properly initialized in libata-eh. This allows ata_gen_ata_sense()
to report the failed block number correctly to SCSI after a media error
during NCQ.
This patch may also be a candidate for backporting to earlier kernels.
Without this fix, SCSI will fail I/O on the entire request rather
than just the bad sector. That can be bad for a request that was
merged from many independent read reads from different tasks.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
These #if's are unneeded since they:
- did anyway not handle the CONFIG_ACPI_DOCK_MODULE case correctly and
- this is already handled in include/acpi/acpi_drivers.h and
- it's now correctly handled in kconfig.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sata_nv hardreset can't classify but was left out while unifying
follow-up SRST request mechanism[1]. This caused detection failures
on those controllers. Fix it.
Reported and bisected by Roland Dreier, Petr Vandrovec and Marc
Dionne. Thanks guys.
[1] 305d2a1ab1
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Roland Dreier <rdreier@cisco.com>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Some chips need AHCI_EN set more than once to actually set it. Try a
few times before giving up and spitting out WARN_ON().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Peer Chen <pchen@nvidia.com>
Cc: Volker Armin Hemmann <volker.armin.hemmann@tu-clausthal.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
WARN_ON()'s in ata_hsm_move() was too liberal and got triggerred when
it shouldn't (e.g. hotplug events at the right moment). As the HSM
only deals with device errors and state machine violations, make it
check only against them.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Mark Lord <liml@rtr.ca>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Since 43cc71eed1, the platform modalias
is prefixed with "platform:". Add MODULE_ALIAS() to the hotpluggable
ATA and IDE platform drivers, to re-enable auto loading.
NOTE: both ata/pata_platform.c and ide/legacy/ide_platform.c claim
to provide "the" platform_pata driver, and there's no build-time
mutual exclusion mechanism. This means that configs which enable
both drivers will make some trouble when hotplugging...
[dbrownell@users.sourceforge.net: more drivers, registration fixes]
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tejun Heo <htejun@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
sis_scr_cfg_read() can't access SError and was incorrectly returning
-1 instead of -EINVAL. This went unnoticed because SError used to be
cleared in @postreset() and it didn't care about how scr_read() failed
but commit ac371987 moved SError clearing into sata_link_resume() and
SCR access failure other than -EINVAL is considered an error condition
and exposes the incorrect return value bug as detection failure. Fix
it.
Also, scsi_scr_cfg_write() was incorrectly returning 0 after it
ignored the request to write to SError. Make it also return -EINVAL.
This was bisected and reported by Patrick McHardy.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Noticed by sparse
drivers/ata/libata-core.c:3380:12: warning: function 'ata_wait_after_reset' with external linkage has definition
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Stephen Rothwell noticed that:
Commit 2be621498d ("x86: dma-ops on highmem
fix") in Linus' tree introduced a new warning (noticed in the x86_64
allmodconfig build of linux-next):
drivers/pci/intel-iommu.c:2240: warning: initialization from incompatible pointer type
Which points at an instance of map_single that needs updating.
Fix it to the new prototype.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/v4l-dvb: (452 commits)
V4L/DVB (7731): tuner-xc2028: fix signal strength calculus
V4L/DVB (7730): tuner-xc2028: Fix SCODE load for MTS firmwares
V4L/DVB (7729): Fix VIDIOCGAP corruption in ivtv
V4L/DVB (7728): tea5761: bugzilla #10462: tea5761 autodetection code were broken
V4L/DVB (7726): cx23885: Enable cx23417 support on the HVR1800
V4L/DVB (7725): cx23885: Add generic cx23417 hardware encoder support
V4L/DVB (7723): pvrusb2: Clean up input selection list generation in V4L interface
V4L/DVB (7722): pvrusb2: Implement FM radio support for Gotview USB2.0 DVD 2
V4L/DVB (7721): pvrusb2: Restructure cx23416 firmware loading to have a common exit point
V4L/DVB (7720): pvrusb2: Fix bad error code on cx23416 firmware load failure
V4L/DVB (7719): pvrusb2: Implement input selection enforcement
V4L/DVB (7718): pvrusb2-dvb: update Kbuild selections
V4L/DVB (7717): pvrusb2-dvb: add DVB-T support for Hauppauge pvrusb2 model 73xxx
V4L/DVB (7716): pvrusb2: clean up global functions
V4L/DVB (7715): pvrusb2: Clean out all use of __FUNCTION__
V4L/DVB (7714): pvrusb2: Fix hang on module removal
V4L/DVB (7713): pvrusb2: Implement cleaner DVB kernel thread shutdown
V4L/DVB (7712): pvrusb2: Close connect/disconnect race
V4L/DVB (7711): pvrusb2: Fix race on module unload
V4L/DVB (7710): pvrusb2: Implement critical digital streaming quirk for onair devices
...
There are different tables for MTS firmwares. This should be taken into
account while selecting the proper firmware.
While at tuner-xc2028.h, improve some comments.
Thanks to Edward J. Sheldrake <ejs1920@yahoo.co.uk> for helping to
diagnose such troubles with PAL/I standard.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Frank Bennett reported that ivtv was causing skype to crash. With help
from one of their developers he showed it was a kernel problem.
VIDIOCGCAP copies a name into a fixed length buffer - ivtv uses names
that are too long and does not truncate them so corrupts a few bytes of
the app data area.
Possibly the names also want trimming but for now this should fix the
corruption case.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx23885: Enable cx23417 support on the HVR1800
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Change how list of possible pvrusb2 inputs is generated to include
only those interfaces that make sense for the interface instance.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
These changes are required with the addition of digital television support
for the Hauppauge HVR1900 & HVR1950, the OnAir Creator and Sasem USB HDTV
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch contains the following cleanups:
- make the following needlessly global function static:
- pvr2_hdw_set_cur_freq()
- #if 0 the following unused global functions:
- pvr2_hdw_get_state_name()
- pvr2_hdw_get_debug_info_unlocked()
- pvr2_hdw_get_debug_info_locked()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Apparently the kernel developers no longer consider it proper
etiquette to use __FUNCTION__; everyone must instead use __func__
(even though it breaks with older compilers). And worse still, actual
effort is being expended to sweep this change throughout the kernel
source tree. Don't these people have better things to do? So...
Completely clean out all use of __FUNCTION__ from the pvrusb2 driver
(it was just in the sysfs interface). I'm not going to use __func__
either. So there.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver was getting had by this scenario:
1. Task A calls kthread_stop() for task B.
2. Before exiting, then Task B calls kthread_stop() for task C.
The problem is, kthread_stop() wants to allocate an internal resource
to itself (i.e. acquire a lock), which won't be released until
kthread_stop() returns. But kthread_stop() won't return until task B
is dead. But task B won't die until it finishes its call to
kthread_stop() for task C, and that will block waiting on the resource
already allocated inside task A. Deadlock.
With the pvrusb2 driver, task A is the caller to pvr_exit(), task B is
the control thread run inside of pvrusb2-context.c, and task C is any
worker thread run inside of pvrusb2-hdw.c.
This problem got introduced by the previous threading setup change,
which was itself an attempt to fix a module tear-down race (which it
actually did fix). The lesson here is that a task being waited on as
part of a kthread_stop() simply cannot be allow to also issue a
kthread_stop() - or we make sure not to issue the enclosing
kthread_stop() until we know that the inner kthread_stop() has
completed first. The solution for the pvrusb2 driver is some hackish
code which changes the main control thread tear down into a two step
process. This then makes it possible to delay issuing the
kthread_stop() on the control thread until after we know that
everything has been torn down first. (And yes, we really need that
kthread_stop() because it's the only way to safely guarantee that a
module-referencing kernel thread has safely returned back out of the
module before we finally remove the module.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Earlier fix to handle DVB feed thread aborts was overly-aggressive.
We can take better advantage of what kthread_stop() can do. This
change simplifies things.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If a disconnect happens before initialization is completed, the
pvrusb2 driver can accidentally touch dangling pointers. The whole
initialization function must be protected by the big_lock, and once
inside that lock, the initialization function should abort if it is
discovered that a disconnect has already taken place.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pvrusb2 driver - for basically forever - was not enforcing a
proper module tear-down. Kernel threads are used inside the driver
and all must be gone before the module can be safely removed. This
changeset reimplements a chunk of pvrusb2-context.c to enforce this
correctly. Unfortunately this is not a simple fix. The new
implementation also cuts back on kernel thread usage; instead of there
being 1 control thread per instance now it's just 1 control thread
shared by all instances. (By dropping to a single thread then the
module exit function can block on its shutdown and the thread itself
can monitor and cleanly shut down all of the other instances first.)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement timed measurement of encoder operation for the first time it
is run. This allows the driver to note when the encoder has been run
successfully for at least 1/4 second. On top of that implement
various bits to ensure that the encoder has been run once before
digital streaming for OnAir devices. This is done via several core
state machine tweaks.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some tuners seem to not work in digital mode unless the encoder is
healthy. Implement a device attribute to represent this flag and
modify the core state machines to enforce this requirement.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the device fails to stream, the feed thread will block forever
waiting for buffers. But while in this state it was not looking for
an exit condition from the driver DVB interface. This caused the
thread to jam. Implement a new stop flag (which will be set
appropriately) to tell the thread to stop.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the DVB interface is not compiled, the pvr2_dvb_props struct is
not available - so it really should be ifdef'ed out as well. This
didn't cause an error because in this context its usage was as an
opaque pointer. But it really shouldn't be present at all if DVB is
not enabled.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The commands to start / stop USB streaming for an analog device are
fairly standard, owing to the fact that all supported devices
apparently started from the same common reference design. However
with digital mode, the commands seem to vary by vendor. This change
makes that variance more explicit. It also cleans up a related
problem for OnAir devices which prevented digital mode from working at
all.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Numerous places in the driver need to issue simple commands to the FX2
microcontroller (e.g. only 1 or 2 bytes, no reply needed). Previously
each place that did this, had to take lock, set up a central buffer,
and call the function to perform the handshake. This change puts
these steps into a single spot. This also has the effect of removing
the need to mess with the control lock from numerous places in the
code.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Implement a mechanism in the pvrusb2 driver for gathering statistics
on the stream buffering, including bytes transferred, buffers handled,
buffers in flight, etc. This is useful for debugging certain classes
of streaming issues and for determining if the buffer pool size is
generally correct for the driver.
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Don't trigger a pathway state change if it's already been triggered
(eliminates some wasted processing and some debug output noise)
Signed-off-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
