Commit Graph

1645 Commits

Author SHA1 Message Date
Samuel Thibault
5193535517 Fix my email address in qd65xx.[ch]/pata_qdi.c
The @fnac.net will be shut down within a couple of months, so fix my
email address.

Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-03 16:53:56 -08:00
Tejun Heo
9062712fa9 libata: implement HORKAGE_1_5_GBPS and apply it to WD My Book
3Gbps is often much more prone to transmission failures.  It's usually
okay to let EH handle speed down after transmission failures but some
WD My Book drives completely shutdown after certain transmission
failures and after it only power cycling can revive them.  Combined
with the fact that external drives often end up with cable assembly
which is longer than usual and more likely to have intervening gender,
this makes these drives very likely to shutdown under certain
configurations virtually rendering them unusable.

This patch implements HOARKGE_1_5_GBPS and applies it to WD My Book
such that 1.5Gbps is forced once the device is identified.

Please take a look at the following bz for related reports.

  http://bugzilla.kernel.org/show_bug.cgi?id=9913

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:04:31 -05:00
Tejun Heo
cf9a590a9e libata: add no penalty retry request for EH device handling routines
Let -EAGAIN from EH device handling routines trigger EH retry without
consuming its tries count.  This will be used to implement link SPD
horkage which requires hardreset to adjust SPD without affecting other
EH decisions.  As it bypasses the forward progress guarantee provided
by the tries count, the requester is responsible for ensuring forward
progress.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:04:19 -05:00
Tejun Heo
c2c7a89c5e libata: improve probe failure handling
When link is flaky at high speed, it isn't uncommon for a device to
repeatedly fail probing sequence early after successfully negotiating
high link speed.  This often leads to consecutive hotplug events
without successful probing.

This patch improves libata EH such that it remembers probing trials
and if there have been more than two unsuccessful trials in the past
60 seconds, slows down link speed to 1.5Gbps.

As link speed negotiation is the duty of the PHY layer proper, the
goal of this fallback mechanism is to provide the last resort when
everything else fails, which unfortunately happens not too
infrequently, so no fancy 6->3->1.5 speeding down or highest
successful transmission speed seen kind of logics (yet).

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:34 -05:00
Tejun Heo
a07d499b47 libata: add @spd_limit to sata_down_spd_limit()
Add @spd_limit to sata_down_spd_limit() so that the caller can specify
the SPD limit it wants.  This parameter doesn't get in the way even
when it's too low.  The closest possible limit is applied.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:22 -05:00
Tejun Heo
99cf610aa4 libata: clear dev->ering in smarter way
dev->ering used to be cleared together with the rest of ata_device in
ata_dev_init() which is called whenever a probing event occurs.
dev->ering is about to be used to track probing failures so it needs
to remain persistent over multiple porbing events.  This patch
achieves this by doing the following.

* Instead of CLEAR_OFFSET, define CLEAR_BEGIN and CLEAR_END and only
  clear between BEGIN and END.  ering is moved after END.  The split
  of persistent area is to allow hotter items remain at the head.

* ering is explicitly cleared on ata_dev_disable() and when device
  attach succeeds.  So, ering is persistent throug a device's life
  time (unless explicitly cleared of course) and also through periods
  inbetween disablement of an attached device and successful detection
  of the next one.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:17 -05:00
Tejun Heo
9913ff8abf libata: check onlineness before using SPD in sata_down_spd_limit()
sata_down_spd_limit() should check whether the link is online before
using the SPD value to determine how to limit the link speed.  Factor
out onlineness test and test it from sata_down_spd_limit().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:08 -05:00
Tejun Heo
678afac678 libata: move ata_dev_disable() to libata-eh.c
ata_dev_disable() is about to be more tightly integrated into EH
logic.  Move it to libata-eh.c.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:03:00 -05:00
Tejun Heo
d89293abd9 libata: fix EH device failure handling
The dev->pio_mode > XFER_PIO_0 test is there to avoid unnecessary
speed down warning messages but it accidentally disabled SATA link spd
down during configuration phase after reset where PIO mode is always
zero.

This patch fixes the problem by moving the test where it belongs.
This makes libata probing sequence behave better when the connection
is flaky at higher link speeds which isn't too uncommon for eSATA
devices.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:02:57 -05:00
Tejun Heo
8d993eaa9c sata_nv: ck804 has borked hardreset too
While playing with nvraid, I found out that rmmoding and insmoding
often trigger hardreset failure on the first port (the second one was
always okay).  Seriously, how diverse can you get with hardreset
behaviors?  Anyways, make ck804 use noclassify variant too.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 23:02:38 -05:00
Randy Dunlap
5eb66fe05f libata: fix kernel-doc warnings
Fix libata kernel-doc warnings:

Warning(linux-next-20090120//drivers/ata/libata-core.c:4720): Excess function parameter 'dev' description in 'ata_qc_new'
Warning(linux-next-20090120//drivers/ata/libata-scsi.c:428): No description found for parameter 'ap'

Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:45 -05:00
Arjan van de Ven
f3d7f23f87 ahci: add a module parameter to ignore the SSS flags for async scanning
The SSS flag, which directs the OS to spin up one disk at a time
to not have the PSU blow out, sometimes gets set even when not needed.
The effect of this is a longer-than-needed boot time.

This patch adds a module parameter that makes the driver ignore SSS
at least as far as the parallel scan during boot is concerned...

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:39 -05:00
Mark Lord
4462254ac6 sata_mv: Fix chip type for Hightpoint RocketRaid 1740/1742
Fix chip type for the Highpoint RocketRAID 1740 and 1742 PCI cards.
These really do have Marvell 6042 chips on them, rather than the 5081 chip.

Confirmed by multiple (two) users (for the 1740), and by examining
the product photographs from Highpoint's web site.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:41:29 -05:00
Pasi Kärkkäinen
41137aa61c [libata] sata_sil: Fix compilation error with libata debugging enabled
I tried compiling 2.6.29-rc1 and 2.6.29-rc3 with libata debugging enabled
and got the following error:

  CC [M]  drivers/ata/sata_sil.o
drivers/ata/sata_sil.c: In function 'sil_fill_sg':
drivers/ata/sata_sil.c:327: error: 'pi' undeclared (first use in this function)
drivers/ata/sata_sil.c:327: error: (Each undeclared identifier is reported only once
drivers/ata/sata_sil.c:327: error: for each function it appears in.)
make[2]: *** [drivers/ata/sata_sil.o] Error 1
make[1]: *** [drivers/ata] Error 2
make: *** [drivers] Error 2

include/linux/libata.h has the following enabled:

#define ATA_DEBUG
#define ATA_VERBOSE_DEBUG
#define ATA_IRQ_TRAP

This fixes the compilation.

Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-02-02 22:38:29 -05:00
Alexander Beregalov
1737ef7598 sata_sil: Fix build breakage
Commit e57db7b (SATA Sil: Blacklist system that spins off disks during ACPI power off)
 breaks build like the following, in both cases when CONFIG_DMI set or not.

        drivers/ata/sata_sil.c: In function 'sil_broken_system_poweroff':
        drivers/ata/sata_sil.c:713: error: implicit declaration of function 'dmi_first_match'
        drivers/ata/sata_sil.c:713: warning: initialization makes pointer from integer without a cast

  sata_sil.c should include dmi.h

Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-29 18:19:30 -08:00
Linus Torvalds
490a8d70cd Merge branch 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev
* 'hibern_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
  SATA PIIX: Blacklist system that spins off disks during ACPI power off
  SATA Sil: Blacklist system that spins off disks during ACPI power off
  SATA AHCI: Blacklist system that spins off disks during ACPI power off
  SATA: Blacklisting of systems that spin off disks during ACPI power off
  DMI: Introduce dmi_first_match to make the interface more flexible
  Hibernation: Introduce system_entering_hibernation
2009-01-27 07:50:41 -08:00
Rafael J. Wysocki
5f451fe1ab SATA PIIX: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP 2510p that uses the ata_piix driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:53 -05:00
Rafael J. Wysocki
e57db7bde7 SATA Sil: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6325 that uses the sata_sil driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:52 -05:00
Rafael J. Wysocki
1fd684346d SATA AHCI: Blacklist system that spins off disks during ACPI power off
Some notebooks from HP have the problem that their BIOSes attempt to
spin down hard drives before entering ACPI system states S4 and S5.
This leads to a yo-yo effect during system power-off shutdown and the
last phase of hibernation when the disk is first spun down by the
kernel and then almost immediately turned on and off by the BIOS.
This, in turn, may result in shortening the disk's life times.

To prevent this from happening we can blacklist the affected systems
using DMI information.

Blacklist HP nx6310 that uses the AHCI driver.

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:51 -05:00
Rafael J. Wysocki
2a6e58d273 SATA: Blacklisting of systems that spin off disks during ACPI power off
Introduce new libata flags ATA_FLAG_NO_POWEROFF_SPINDOWN and
ATA_FLAG_NO_HIBERNATE_SPINDOWN that, if set, will prevent disks from
being spun off during system power off and hibernation, respectively
(to handle the hibernation case we need the new system state
SYSTEM_HIBERNATE_ENTER that can be checked against by libata, in
analogy with SYSTEM_POWER_OFF).

Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:15:49 -05:00
Phil Sutter
b98f504639 pata-rb532-cf: remove set_irq_type from finish_io
The driver has been tested without the call to set_irq_type at this
point and occurs to work fine, so it should be safe to remove it.

Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-27 02:13:03 -05:00
JosephChan@via.com.tw
e4d866cdea [libata] pata_via: support VX855, future chips whose IDE controller use 0x0571
It supports VX855 and future chips whose IDE controller uses PCI ID 0x0571.

Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:51:26 -05:00
Mark Lord
f9228c7ffa sata_mv: no longer experimental (v2)
Update Kconfig for sata_mv with full list of chips supported,
and (finally!) remove the "EXPERIMENTAL" designations.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:42:10 -05:00
Mark Lord
6d3c30efc9 sata_mv: msi masking fix (v2)
Enable reliable use of Message-Signaled Interrupts (MSI) in sata_mv
by masking further chip interrupts within the main interrupt handler.

Based upon a suggestion by Grant Grundler.
MSI is working reliably in all of my test systems here now.

Signed-off-by: Mark Lord <mlord@pobox.com>
Reviewed-by: Grant Grundler <grundler@google.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:41:57 -05:00
Thomas Reitmayr
5d0fb2e730 sata_mv: Properly initialize main irq mask
I noticed that during initialization sata_mv.c assumes that the main
interrupt mask has its default value of 0. The function
mv_platform_probe(..) initializes a shadow irq mask with 0 assuming
that's the value of the controller's register. Now
mv_set_main_irq_mask(..) only writes the controller's register if the
new value differs from the "shadowed" value. This is fatal when trying
to disable all interrupts in mv_init_host(..), i.e. the following
function call does not write anything to the main irq mask register:

  mv_set_main_irq_mask(host, ~0, 0);

The effect I see on my machine (QNAP TS-109 II) with booting via kexec
(with Linux as a 2nd-stage boot loader) is that if the sata_mv module
was still loaded when performing kexec, then the new kernel's sata_mv
module starts up with interrupts enabled. This results in an unhandled
IRQ and breaks the boot process.

The unhandled interrupt itself might also be fixed by Lennert's patch
proposed at http://markmail.org/message/kwvzxstnlsa3s26w which I did not
try yet.

However I still propose to additionally initialize the shadow variable
with the current contents of the main irq mask register to get both in
sync and allow proper disabling the main irq mask. This fixes the
unhandled irq on my machine.

Signed-off-by: Thomas Reitmayr <treitmayr@devbase.at>
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:37:37 -05:00
Mark Lord
cd12e1f7a2 sata_mv: remove bogus nsect restriction
Remove unneeded nsect restriction from GenII NCQ path,
and improve comments to explain why this is not a problem.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:37:00 -05:00
Mark Lord
cae6edc3b5 sata_mv: don't read hc_irq_cause
Remove silly read-modify-write sequences when clearing interrupts
in hc_irq_cause.  This gets rid of unneeded MMIO reads, resulting in
a slight performance boost when switching between EDMA and non-EDMA
modes (eg. for cache flushes).

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:53 -05:00
Mark Lord
b0bccb18bc sata_mv: fix 8-port timeouts on 508x/6081 chips
Fix a longstanding bug for the 8-port Marvell Sata controllers (508x/6081),
where accesses to the upper 4 ports would cause lost-interrupts / timeouts
for the lower 4-ports.  With this patch, the 6081 boards should finally be
reliable enough for mainstream use with Linux.

Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:41 -05:00
Tejun Heo
2d775708bc sata_nv: fix MCP5x reset
MCP5x family of controllers seem to share much more with nf2's as far
as reset protocol is concerned.  It requires heardreset to get the PHY
going and classfication code report after hardreset is unreliable.
Create a new board type MCP5x and use noclassify hardreset.  SWNCQ is
modified to inherit from this new type.

This fixes hotplug regression reported in kernel bz#12351.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:31 -05:00
Tejun Heo
e8caa3c70e sata_nv: rename nv_nf2_hardreset()
nv_nf2_hardreset() will be used by other flavors too.  Rename it to
nv_noclassify_hardreset().

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:29 -05:00
Tejun Heo
b919930c34 libata: set NODEV_HINT for 0x7f status
Asus Pundit-R with atiixp controller has the second port missing and,
very unusually, its status is stuck at 0x7f and all others at 0.  This
meanst that it fails TF access test but gets detected as a disk due to
classification code check and then evades polling IDENTIFY presence
detection thanks to the missing BSY in the status value causing
excessive delays during boot.

This patch makes libata-sff HSM set NODEV_HINT if the status is 0x7f
to make polling IDENTIFY presence detection work for these machines.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:26 -05:00
Tejun Heo
80ee6f54f5 libata-sff: fix incorrect EH message
The EH message for NODEV_HINT path was describing the opposite
condition.  Fix it.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-26 06:36:16 -05:00
Michal Sojka
e4ac522bd7 sata_fsl: Return non-zero on error in probe()
while I was looking over kernel sources I've found this small bug.

Formerly, zero was returned even if an error happened.

Signed-off-by: Michal Sojka <sojkam1@fel.cvut.cz>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:58 -05:00
Andrew Morton
bc42b24e6e drivers/ata/pata_ali.c: s/isa_bridge/ali_isa_bridge/ to fix alpha build
drivers/ata/pata_ali.c:44: error: static declaration of 'isa_bridge' follows non-static declaration
arch/alpha/include/asm/pci.h:274: error: previous declaration of 'isa_bridge' was here

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:43 -05:00
David Daney
3c929c6f5a libata: New driver for OCTEON SOC Compact Flash interface (v7).
Cavium OCTEON processor support was recently merged, so now we have
this CF driver for your consideration.

Most OCTEON variants have *no* DMA or interrupt support on the CF
interface so for these, only PIO is supported.  Although if DMA is
available, we do take advantage of it.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:39 -05:00
David Daney
3ada9c1264 libata: Add another column to the ata_timing table.
The forthcoming OCTEON SOC Compact Flash driver needs an additional
timing value that was not available in the ata_timing table.  I add a
new column for dmack_hold time.  The values were obtained from the
Compact Flash specification Rev 4.1.

Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:37 -05:00
JosephChan@via.com.tw
6813952021 sata_via: Add VT8261 support
Signed-off-by: Joseph Chan <josephchan@via.com.tw>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:23:22 -05:00
Tejun Heo
16028232bf pata_atiixp: update port enabledness test handling
Port enabledness test fits much better into init_one() instead of
pre_reset().  The reason why these tests are in pre_reset() is purely
historical at this point.  Move it to init_one().  This will help
further changes.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:20:27 -05:00
Jeff Garzik
94be9a58d7 [libata] get-identity ioctl: Fix use of invalid memory pointer
for SAS drivers.

Caught by Ke Wei (and team?) at Marvell.

Also, move the ata_scsi_ioctl export to libata-scsi.c, as that seems to be the
general trend.

Acked-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-16 10:17:09 -05:00
Alan Cox
4a99d95fa8 pata_it821x: Update RDC UDMA handling
The UDMA affliction is apparently specific to revision 0x11. Keeps us in sync
with drivers/ide current.

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-13 10:35:01 -05:00
Christian Borntraeger
a0f79f7ad3 ata: fix wrong WARN_ON_ONCE
This patch fixes a wrong WARN_ON that was triggered by 32bit PIO support:
WARNING: at drivers/ata/libata-sff.c:1017 ata_sff_hsm_move+0x45e/0x750()

__atapi_pio_bytes simply doesnt know enough to decide if there is a bug.

Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-13 10:34:59 -05:00
Arjan van de Ven
fa853a4841 libata: only ports >= 0 need to synchronize
In a discussio with Jeff Garzik, he mentioned that the serialization
for the libata port probes only needs to be within the domain of a host.
This means that for the first port of each host (with ID 0), we don't
need to wait, so we can relax our serialization a little.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-10 15:06:52 -08:00
Arjan van de Ven
886ad09fc8 libata: Add a per-host flag to opt-in into parallel port probes
This patch adds a per host flag that allows drivers to opt in into
having its busses scanned in parallel.

Drivers that do not set this flag get their ports scanned in
the "original" sequence.

Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-10 15:06:52 -08:00
Linus Torvalds
a3a798c88a Merge branch 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (94 commits)
  ACPICA: hide private headers
  ACPICA: create acpica/ directory
  ACPI: fix build warning
  ACPI : Use RSDT instead of XSDT by adding boot option of "acpi=rsdt"
  ACPI: Avoid array address overflow when _CST MWAIT hint bits are set
  fujitsu-laptop: Simplify SBLL/SBL2 backlight handling
  fujitsu-laptop: Add BL power, LED control and radio state information
  ACPICA: delete utcache.c
  ACPICA: delete acdisasm.h
  ACPICA: Update version to 20081204.
  ACPICA: FADT: Update error msgs for consistency
  ACPICA: FADT: set acpi_gbl_use_default_register_widths to TRUE by default
  ACPICA: FADT parsing changes and fixes
  ACPICA: Add ACPI_MUTEX_TYPE configuration option
  ACPICA: Fixes for various ACPI data tables
  ACPICA: Restructure includes into public/private
  ACPI: remove private acpica headers from driver files
  ACPI: reboot.c: use new acpi_reset interface
  ACPICA: New: acpi_reset interface - write to reset register
  ACPICA: Move all public H/W interfaces to new hwxface
  ...
2009-01-09 11:55:14 -08:00
Tejun Heo
efcb3cf7f0 libata: use WARN_ON_ONCE on hot paths
Convert WARN_ON() on command issue/completion paths to WARN_ON_ONCE()
so that libata doesn't spam the machine even when one of those
conditions triggers repeatedly.

Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-01-09 11:54:22 -08:00
Len Brown
b2576e1d44 Merge branch 'linus' into release 2009-01-09 03:39:43 -05:00
Alan Cox
0fe40ff891 libata: clean up the SFF code for coding style
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-08 16:40:25 -05:00
Alan Cox
871af1210f libata: Add 32bit PIO support
This matters for some controllers and in one or two cases almost doubles
PIO performance. Add a bmdma32 operations set we can inherit and activate
it for some controllers

Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-08 16:34:27 -05:00
Shane Huang
e427fe042c [libata] ahci: Withdraw IGN_SERR_INTERNAL for SB800 SATA
There is an issue in ATI SB600/SB700 SATA that PxSERR.E should not be
set on some conditions, which will lead to many SATA ODD error messages.
commit 55a61604cd is the workaround.
Since SB800 fixed this HW issue, IGN_SERR_INTERNAL should be withdrawn
for SB800.

Signed-off-by: Shane Huang <shane.huang@amd.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-08 16:32:05 -05:00
Tejun Heo
6ecb6f25d3 pata_hpt366: reimplement mode programming
Reimplement mode programming logic of pata_hpt366 such that it's
identical to that of IDE hpt366 driver.  The differences were...

* pata_hpt366 used 0xCFFF8FFFF to mask pio modes and 0x3FFFFFFF dma
  modes.  IDE hpt366 uses 0xC1F8FFFF for PIO, 0x303800FF for MWDMA and
  0x30070000 for UDMA.

* pata_hpt366 doesn't set 0x08000000 for PIO unless it's already set
  and always turns it on for MWDMA/UDMA.  IDE hpt366 doesn't bother
  with the bit.  It always uses what was there.

* IDE hpt366 always clears 0xC0000000.  pata_hpt366 doesn't.

Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
2009-01-08 16:29:20 -05:00