Pull MIPS updates from Ralf Baechle:
"The MIPS bits for 3.8. This also includes a bunch fixes that were
sitting in the linux-mips.org git tree for a long time. This pull
request contains updates to several OCTEON drivers and the board
support code for BCM47XX, BCM63XX, XLP, XLR, XLS, lantiq, Loongson1B,
updates to the SSB bus support, MIPS kexec code and adds support for
kdump.
When pulling this, there are two expected merge conflicts in
include/linux/bcma/bcma_driver_chipcommon.h which are trivial to
resolve, just remove the conflict markers and keep both alternatives."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (90 commits)
MIPS: PMC-Sierra Yosemite: Remove support.
VIDEO: Newport Fix console crashes
MIPS: wrppmc: Fix build of PCI code.
MIPS: IP22/IP28: Fix build of EISA code.
MIPS: RB532: Fix build of prom code.
MIPS: PowerTV: Fix build.
MIPS: IP27: Correct fucked grammar in ops-bridge.c
MIPS: Highmem: Fix build error if CONFIG_DEBUG_HIGHMEM is disabled
MIPS: Fix potencial corruption
MIPS: Fix for warning from FPU emulation code
MIPS: Handle COP3 Unusable exception as COP1X for FP emulation
MIPS: Fix poweroff failure when HOTPLUG_CPU configured.
MIPS: MT: Fix build with CONFIG_UIDGID_STRICT_TYPE_CHECKS=y
MIPS: Remove unused smvp.h
MIPS/EDAC: Improve OCTEON EDAC support.
MIPS: OCTEON: Add definitions for OCTEON memory contoller registers.
MIPS: OCTEON: Add OCTEON family definitions to octeon-model.h
ata: pata_octeon_cf: Use correct byte order for DMA in when built little-endian.
MIPS/OCTEON/ata: Convert pata_octeon_cf.c to use device tree.
MIPS: Remove usage of CEVT_R4K_LIB config option.
...
I had no idea just how broken IOC3 was until I read this.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some initialization errors are reported with the existing OCTEON EDAC
support patch. Also some parts have more than one memory controller.
Fix the errors and add multiple controllers if present.
Signed-off-by: David Daney <david.daney@cavium.com>
Drivers for EDAC on Cavium. Supported subsystems are:
o CPU primary caches. These are parity protected only, so only error
reporting.
o Second level cache - ECC protected, provides SECDED.
o Memory: ECC / SECDEC if used with suitable DRAM modules. The driver will
will only initialize if ECC is enabled on a system so is safe to run on
non-ECC memory.
o PCI: Parity error reporting
Since it is very hard to test this sort of code the implementation is very
conservative and uses polling where possible for now.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Reviewed-by: Borislav Petkov <borislav.petkov@amd.com>
Remove conditional code based on CONFIG_HOTPLUG being false. It's
always on now in preparation of it going away as an option.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the nlm_set_pic_extra_ack() call to setup the extra interrupt
ACK needed by XLR PCI and XLS PCIe. Simplify the code by adding
nlm_pci_link_to_irq().
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4561
Signed-off-by: John Crispin <blogic@openwrt.org>
Use the new reset helper where appropriate.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Patchwork: http://patchwork.linux-mips.org/patch/4453
Signed-off-by: John Crispin <blogic@openwrt.org>
Add a PCIe clock and use that instead of directly touching the clock
control register. While at it, fail if there is no such clock.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Acked-by: Florian Fainelli <florian@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4452
Signed-off-by: John Crispin <blogic@openwrt.org>
LD arch/mips/pci/built-in.o
WARNING: arch/mips/pci/built-in.o(.devinit.text+0x2a0): Section mismatch in reference from the function malta_piix_func0_fixup() to the variable .init.data:pci_irq
The function __devinit malta_piix_func0_fixup() references
a variable __initdata pci_irq.
If pci_irq is only used by malta_piix_func0_fixup then
annotate pci_irq with a matching annotation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Most architectures implement this in exactly the same way. Instead of
having each architecture duplicate this function, provide a single
implementation in the core and make it a weak symbol so that it can be
overridden on architectures where it is required.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Remove the __init annotations in order to keep pci_fixup_irqs() around
after init (e.g. for hotplug). This requires the same change for the
implementation of pcibios_update_irq() on all architectures. While at
it, all __devinit annotations are removed as well, since they will be
useless now that HOTPLUG is always on.
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* commit 'v3.6-rc5': (1098 commits)
Linux 3.6-rc5
HID: tpkbd: work even if the new Lenovo Keyboard driver is not configured
Remove user-triggerable BUG from mpol_to_str
xen/pciback: Fix proper FLR steps.
uml: fix compile error in deliver_alarm()
dj: memory scribble in logi_dj
Fix order of arguments to compat_put_time[spec|val]
xen: Use correct masking in xen_swiotlb_alloc_coherent.
xen: fix logical error in tlb flushing
xen/p2m: Fix one-off error in checking the P2M tree directory.
powerpc: Don't use __put_user() in patch_instruction
powerpc: Make sure IPI handlers see data written by IPI senders
powerpc: Restore correct DSCR in context switch
powerpc: Fix DSCR inheritance in copy_thread()
powerpc: Keep thread.dscr and thread.dscr_inherit in sync
powerpc: Update DSCR on all CPUs when writing sysfs dscr_default
powerpc/powernv: Always go into nap mode when CPU is offline
powerpc: Give hypervisor decrementer interrupts their own handler
powerpc/vphn: Fix arch_update_cpu_topology() return value
ARM: gemini: fix the gemini build
...
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/rapidio/devices/tsi721.c
If the controller has no PCIe module attached, accessing of the device
configuration space causes a data bus error. Avoid this by checking the
status of the PCIe link in advance, and indicate an error if the link
is down.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: stable@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4293/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull MIPS updates from Ralf Baechle:
"More hardware support across the field including a bunch of device
drivers. The highlight however really are further steps towards
device tree.
This has been sitting in -next for ages. All MIPS _defconfigs have
been tested to boot or where I don't have hardware available, to at
least build fine."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (77 commits)
MIPS: Loongson 1B: Add defconfig
MIPS: Loongson 1B: Add board support
MIPS: Netlogic: early console fix
MIPS: Netlogic: Fix indentation of smpboot.S
MIPS: Netlogic: remove cpu_has_dc_aliases define for XLP
MIPS: Netlogic: Remove unused pcibios_fixups
MIPS: Netlogic: Add XLP SoC devices in FDT
MIPS: Netlogic: Add IRQ mappings for more devices
MIPS: Netlogic: USB support for XLP
MIPS: Netlogic: XLP PCIe controller support.
MIPS: Netlogic: Platform changes for XLR/XLS I2C
MIPS: Netlogic: Platform NAND/NOR flash support
MIPS: Netlogic: Platform changes for XLS USB
MIPS: Netlogic: Remove NETLOGIC_ prefix
MIPS: Netlogic: SMP wakeup code update
MIPS: Netlogic: Update comments in smpboot.S
MIPS: BCM63XX: Add 96328avng reference board
MIPS: Expose PCIe drivers for MIPS
MIPS: BCM63XX: Add PCIe Support for BCM6328
MIPS: BCM63XX: Move the PCI initialization into its own function
...
Host bridge hotplug
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos Kong)
Dynamic resource management
- Track bus number allocation (struct resource tree per domain) (Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment (Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup() (Myron Stowe)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=oo/A
-----END PGP SIGNATURE-----
Merge tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI changes from Bjorn Helgaas:
"Host bridge hotplug:
- Add MMCONFIG support for hot-added host bridges (Jiang Liu)
Device hotplug:
- Move fixups from __init to __devinit (Sebastian Andrzej Siewior)
- Call FINAL fixups for hot-added devices, too (Myron Stowe)
- Factor out generic code for P2P bridge hot-add (Yinghai Lu)
- Remove all functions in a slot, not just those with _EJx (Amos
Kong)
Dynamic resource management:
- Track bus number allocation (struct resource tree per domain)
(Yinghai Lu)
- Make P2P bridge 1K I/O windows work with resource reassignment
(Bjorn Helgaas, Yinghai Lu)
- Disable decoding while updating 64-bit BARs (Bjorn Helgaas)
Power management:
- Add PCIe runtime D3cold support (Huang Ying)
Virtualization:
- Add VFIO infrastructure (ACS, DMA source ID quirks) (Alex
Williamson)
- Add quirks for devices with broken INTx masking (Jan Kiszka)
Miscellaneous:
- Fix some PCI Express capability version issues (Myron Stowe)
- Factor out some arch code with a weak, generic, pcibios_setup()
(Myron Stowe)"
* tag 'for-3.6' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (122 commits)
PCI: hotplug: ensure a consistent return value in error case
PCI: fix undefined reference to 'pci_fixup_final_inited'
PCI: build resource code for M68K architecture
PCI: pciehp: remove unused pciehp_get_max_lnk_width(), pciehp_get_cur_lnk_width()
PCI: reorder __pci_assign_resource() (no change)
PCI: fix truncation of resource size to 32 bits
PCI: acpiphp: merge acpiphp_debug and debug
PCI: acpiphp: remove unused res_lock
sparc/PCI: replace pci_cfg_fake_ranges() with pci_read_bridge_bases()
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: support sizing P2P bridge I/O windows with 1K granularity
PCI: reimplement P2P bridge 1K I/O windows (Intel P64H2)
PCI: disable MEM decoding while updating 64-bit MEM BARs
PCI: leave MEM and IO decoding disabled during 64-bit BAR sizing, too
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
...
Adds support for the XLP on-chip PCIe controller. On XLP, the
on-chip devices(including the 4 PCIe links) appear in the PCIe
configuration space of the XLP as PCI devices.
The changes are to initialize and register the PCIe controller,
enable hardware byte swap in the PCIe IO and MEM space, and to
enable PCIe interrupts.
Signed-off-by: Ganesan Ramalingam <ganesanr@netlogicmicro.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3760/
Patchwork: https://patchwork.linux-mips.org/patch/4104/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for the PCIe port found on BCM6328.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3956/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Also make the cpu check a bit more explicit.
Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: Maxime Bizon <mbizon@freebox.fr>
Cc: Florian Fainelli <florian@openwrt.org>
Cc: Kevin Cernekee <cernekee@gmail.com>
Patchwork: https://patchwork.linux-mips.org/patch/3953/
Reviewed-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull late MIPS fixes from Ralf Baechle:
"This fixes a number of lose ends in the MIPS code and various bug
fixes.
Aside of dropping some patch that should not be in this pull request
everything has sat in -next for quite a while and there are no known
issues.
The biggest patch in this patch set moves the allocation of an array
that is aliased to a function (for runtime generated code) to
assembler code. This avoids an issue with certain toolchains when
building for microMIPS."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (35 commits)
MIPS: PCI: Move fixups from __init to __devinit.
MIPS: Fix bug.h MIPS build regression
MIPS: sync-r4k: remove redundant irq operation
MIPS: smp: Warn on too early irq enable
MIPS: call set_cpu_online() on cpu being brought up with irq disabled
MIPS: call ->smp_finish() a little late
MIPS: Yosemite: delay irq enable to ->smp_finish()
MIPS: SMTC: delay irq enable to ->smp_finish()
MIPS: BMIPS: delay irq enable to ->smp_finish()
MIPS: Octeon: delay enable irq to ->smp_finish()
MIPS: Oprofile: Fix build as a module.
MIPS: BCM63XX: Fix BCM6368 IPSec clock bit
MIPS: perf: Fix build error caused by unused counters_per_cpu_to_total()
MIPS: Fix Magic SysRq L kernel crash.
MIPS: BMIPS: Fix duplicate header inclusion.
mips: mark const init data with __initconst instead of __initdata
MIPS: cmpxchg.h: Add missing include
MIPS: Malta may also be equipped with MIPS64 R2 processors.
MIPS: Fix typo multipy -> multiply
MIPS: Cavium: Fix duplicate ARCH_SPARSEMEM_ENABLE in kconfig.
...
Fixups are executed once the pci-device is found which is during boot
process so __init seems fine as long as the platform does not support
hotplug.
However it is possible to remove the PCI bus at run time and have it
rediscovered again via "echo 1 > /sys/bus/pci/rescan" and this will call
the fixups again.
[ralf@linux-mips.org: Made piixirqmap[] in malta_piix_func0_fixup()
__initdata.]
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As long as there is no other non-const variable marked __initdata in the
same compilation unit it doesn't hurt. If there were one however
compilation would fail with
error: $variablename causes a section type conflict
because a section containing const variables is marked read only and so
cannot contain non-const variables.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: linux-mips@linux-mips.org
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Cc: kernel@pengutronix.de
Patchwork: https://patchwork.linux-mips.org/patch/3565/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* pci/myron-final-fixups-v2:
PCI: call final fixups hot-added devices
PCI: move final fixups from __init to __devinit
x86/PCI: move final fixups from __init to __devinit
MIPS/PCI: move final fixups from __init to __devinit
PCI: never discard enable/suspend/resume_early/resume fixups
PCI: release temporary reference in __nv_msi_ht_cap_quirk()
PCI: restructure 'pci_do_fixups()'
Final fixups are executed during device enumeration. If we support
hotplug, this may be after boot, so final fixups cannot be __init.
[bhelgaas: changelog]
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
* pci/myron-pcibios_setup:
xtensa/PCI: factor out pcibios_setup()
x86/PCI: adjust section annotations for pcibios_setup()
unicore32/PCI: adjust section annotations for pcibios_setup()
tile/PCI: factor out pcibios_setup()
sparc/PCI: factor out pcibios_setup()
sh/PCI: adjust section annotations for pcibios_setup()
sh/PCI: factor out pcibios_setup()
powerpc/PCI: factor out pcibios_setup()
parisc/PCI: factor out pcibios_setup()
MIPS/PCI: adjust section annotations for pcibios_setup()
MIPS/PCI: factor out pcibios_setup()
microblaze/PCI: factor out pcibios_setup()
ia64/PCI: factor out pcibios_setup()
cris/PCI: factor out pcibios_setup()
alpha/PCI: factor out pcibios_setup()
PCI: pull pcibios_setup() up into core
This patch fixes two checks for valid gpio number, formerly (wrongly)
considering zero as invalid, now using gpio_is_valid().
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
MSI interrupts do not work on XLS after commit a776c49
( "PCI: msi: Disable msi interrupts when we initialize a pci device" )
because the change disables MSI interrupts on the XLS PCIe bridges
during the PCI enumeration.
Fix this by enabling MSI interrupts on the bridge in the
arch_setup_msi_irq() function. A new function xls_get_pcie_link()
has been introduced to get the PCI device corresponding to the
top level PCIe bridge on which MSI has to be enabled.
Also, update get_irq_vector() to use the new xls_get_pcie_link()
function and PCI_SLOT() macro for determining the IRQ of PCI devices.
Signed-off-by: Ganesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3753/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the struct pci_bus secondary/subordinate members with the
struct resource busn_res. Later we'll build a resource tree of these
bus numbers.
[bhelgaas: changelog]
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Implement support for OF inside the lantiq PCI driver. The patch also splits
pcibios_plat_dev_init and pcibios_map_irq out into their own file to accomodate
coexistance with the upcoming pcie driver.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3806/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
As part of the conversion to OF we also implement pinctrl drivers. Previously
we used ltq_gpio_request() to set pinmuxing. This is now obselete and we can
hence drop the function.
Additionally we remove gpio_to_irq() from the gpio driver and move it to a
header file.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3801/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implement pci_load_of_ranges on MIPS. Due to lack of test hardware only 32bit
bus width is supported. This function is based on pci_process_bridge_OF_ranges
from powerpc.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3729/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The AR724X specific PCI code can be used for the
AR934X SoCs, however it can be selected only if
SOC_AR724X is set.
Introduce a new Kconfig symbol in order to be able
to use the code for AR934X as well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Luis R. Rodriguez <mcgrof@qca.qualcomm.com>
Cc: linux-mips@linux-mips.org
Cc: mcgrof@infradead.org
Patchwork: https://patchwork.linux-mips.org/patch/3514/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add copyright records according to the recent changes in
the PCI code. Also fix up the descriptions.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3503/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Atheros AR71XX SoCs have a built-in PCI Host Controller.
This patch adds a driver for that, and modifies the relevant
files in order to allow to register the PCI controller from
board specific setup.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3498/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The PCI Host Controller of the AR724x SoC has a
built-in IRQ controller. The current code does
not supports that, so the IRQ lines wired to this
controller are not usable. This leads to failed
'request_irq' calls:
ath9k 0000:00:00.0: request_irq failed
ath9k: probe of 0000:00:00.0 failed with error -89
This patch adds support for the IRQ controller
in order to make PCI IRQs work.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3496/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current ar724x_pci_{read,write} functions are
broken. Due to that, pci_read_config_byte returns
with bogus values, and pci_write_config_{byte,word}
unconditionally clears the accessed PCI configuration
registers instead of changing the value of them.
The patch fixes the broken functions, thus the PCI
configuration space can be accessed correctly.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3493/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace the 'ath724x' to 'ar724x' in function, variable and
structure names to reflect the name of the real SoC.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: René Bolldorf <xsecute@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3490/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The current code unconditionally registers the AR724X
specific PCI controller, even if the kernel is running
on a different SoC.
Add a common function for PCI controller registration,
and only register the AR724X PCI controller if the kernel
is running on an AR724X SoC.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3488/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The 'pcibios_map_irq' and 'pcibios_plat_dev_init'
are common functions and only instance one of them
can be present in a single kernel.
Currently these functions can be built only if the
CONFIG_SOC_AR724X option is selected. However the
ath79 platform contain support for the AR71XX SoCs,.
The AR71XX SoCs have a differnet PCI controller,
and those will require a different code.
Move the common PCI code into a separeate file in
order to be able to use that with other SoCs as
well.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Acked-by: René Bolldorf <xsecute@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3485/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixes
warning: data definition has no type or storage class [enabled by default]
warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL' [-Wimplicit-int]
warning: parameter names (without types) in function declaration [enabled by default]
Signed-off-by: Matt Turner <mattst88@gmail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3746/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Pull PCI changes (including maintainer change) from Jesse Barnes:
"This pull has some good cleanups from Bjorn and Yinghai, as well as
some more code from Yinghai to better handle resource re-allocation
when enabled.
There's also a new initcall_debug feature from Arjan which will print
out quirk timing information to help identify slow quirks for fixing
or refinement (Yinghai sent in a few patches to do just that once the
new debug code landed).
Beyond that, I'm handing off PCI maintainership to Bjorn Helgaas.
He's been a core PCI and Linux contributor for some time now, and has
kindly volunteered to take over. I just don't feel I have the time
for PCI review and work that it deserves lately (I've taken on some
other projects), and haven't been as responsive lately as I'd like, so
I approached Bjorn asking if he'd like to manage things. He's going
to give it a try, and I'm confident he'll do at least as well as I
have in keeping the tree managed, patches flowing, and keeping things
stable."
Fix up some fairly trivial conflicts due to other cleanups (mips device
resource fixup cleanups clashing with list handling cleanup, ppc iseries
removal clashing with pci_probe_only cleanup etc)
* 'linux-next' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci: (112 commits)
PCI: Bjorn gets PCI hotplug too
PCI: hand PCI maintenance over to Bjorn Helgaas
unicore32/PCI: move <asm-generic/pci-bridge.h> include to asm/pci.h
sparc/PCI: convert devtree and arch-probed bus addresses to resource
powerpc/PCI: allow reallocation on PA Semi
powerpc/PCI: convert devtree bus addresses to resource
powerpc/PCI: compute I/O space bus-to-resource offset consistently
arm/PCI: don't export pci_flags
PCI: fix bridge I/O window bus-to-resource conversion
x86/PCI: add spinlock held check to 'pcibios_fwaddrmap_lookup()'
PCI / PCIe: Introduce command line option to disable ARI
PCI: make acpihp use __pci_remove_bus_device instead
PCI: export __pci_remove_bus_device
PCI: Rename pci_remove_behind_bridge to pci_stop_and_remove_behind_bridge
PCI: Rename pci_remove_bus_device to pci_stop_and_remove_bus_device
PCI: print out PCI device info along with duration
PCI: Move "pci reassigndev resource alignment" out of quirks.c
PCI: Use class for quirk for usb host controller fixup
PCI: Use class for quirk for ti816x class fixup
PCI: Use class for quirk for intel e100 interrupt fixup
...
Conflicts:
drivers/net/vmxnet3/vmxnet3_drv.c
Small vmxnet3 conflict with header size bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Tell the PCI core about host bridge address translation so it can take
care of bus-to-resource conversion for us.
Here's the wrinkle on Cobalt: we can't generate normal I/O port addresses
on PCI because the GT-64111 doesn't do any address translation, so we have
this:
CPU I/O port addresses [io 0x0000-0xffffff]
PCI bus I/O port addresses [io 0x10000000-0x10ffffff]
Legacy-mode IDE controllers start out with the legacy bus addresses, e.g.,
0x1f0, assigned by pci_setup_device(). These are outside the range of
addresses GT-64111 can generate on PCI, but pcibios_fixup_device_resources()
converted them to CPU addresses anyway by adding io_offset. Therefore, we
had to pre-adjust them in cobalt_legacy_ide_fixup().
With io_offset = 0xf0000000, we had this:
res->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x100001f0 -= io_offset in cobalt_legacy_ide_fixup()
res->start = 0x1f0 += io_offset in pcibios_fixup_device_resources()
The difference after this patch is that the generic pci_bus_to_resource()
only adds the offset if the bus address is inside a host bridge window.
Since 0x1f0 is not a valid bus address and is not inside any windows, it is
unaffected, so we now have this:
region->start = 0x1f0 initialized in pci_setup_device()
res->start = 0x1f0 no offset by pci_bus_to_resource()
That means we can remove both pcibios_fixup_device_resources() and
cobalt_legacy_ide_fixup().
I would *rather* set the host bridge offset to zero (which corresponds
to what the GT-64111 actually does), and have both CPU and PCI addresses
of [io 0x10000000-0x10ffffff]. However, that would require changes to
generic code that assumes legacy I/O addresses, such as pic1_io_resource
([io 0x0020-0x00021]), and we'd have to keep a Cobalt IDE fixup.
Of course, none of this changes the fact that references to I/O port
0x1f0 actually go to port 0x100001f0, not 0x1f0, on the Cobalt PCI bus.
Fortunately the VT82C586 IDE controller only decodes the low 24 address
bits, so it does work.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: Yoichi Yuasa <yuasa@linux-mips.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
We never assign anything other than PCI_ASSIGN_ALL_BUSSES to pci_probe,
so just remove the indirection. If configurability is required in the
future, please use the pci_flags/PCI_REASSIGN_ALL_BUS functionality
as is done for powerpc.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some architectures (alpha, mips, powerpc) have an arch-specific
"pci_probe_only" flag. Others use PCI_PROBE_ONLY in pci_flags for
the same purpose. This moves mips to the pci_flags approach so
generic code can use the same test across all architectures.
CC: Ralf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Some SoCs have a PCIe host controller to make it possible to attach
some other devices to it, like an other Wifi card.
This code was tested with an Netgear WNDR3400 (bcm4716 based), but
should work with all bcma based SoCs.
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On MIPS the generic PCI code has always defaulted to L1_CACHE_BYTES
because the architecutre PCI code did not provide a better default.
In particular on systems with S-caches or T-caches this was suboptimal.
Provide a better default by setting pci_dfl_cache_line_size based on
the size of the line size of the lowest level of the cache hierarchy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/2982/
Convert from pci_scan_bus() to pci_scan_root_bus() and remove root bus
resource fixups. This fixes the problem of "early" and "header" quirks
seeing incorrect root bus resources.
Based on original patch by Deng-Cheng Zhu.
Reference: https://lkml.org/lkml/2011/8/26/89
CC: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Deng-Cheng Zhu <dczhu@mips.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The 'latency timer' of PCI devices, both Type 0 and Type 1,
is setup in architecture-specific code [see: 'pcibios_set_master()'].
There are two approaches being taken by all the architectures - check
if the 'latency timer' is currently set between 16 and 255 and if not
bring it within bounds, or, do nothing (and then there is the
gratuitously different PA-RISC implementation).
There is nothing architecture-specific about PCI's 'latency timer' so
this patch pulls its setup functionality up into the PCI core by
creating a generic 'pcibios_set_master()' function using the '__weak'
attribute which can be used by all architectures as a default which,
if necessary, can then be over-ridden by architecture-specific code.
No functional change.
Signed-off-by: Myron Stowe <myron.stowe@redhat.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
- Move code that can be shared with XLP (irq.c, smp.c, time.c and
xlr_console.c) to arch/mips/netlogic/common
- Add asm/netlogic/haldefs.h and asm/netlogic/common.h for common and
io functions shared with XLP
- remove type 'nlm_reg_t *' and use uint64_t for mmio offsets
- Move XLR specific code in smp.c to xlr/wakeup.c
- Move XLR specific PCI code from irq.c to mips/pci/pci-xlr.c
- Provide API for pic functions called from common/irq.c
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2964/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The CPU_XLR config variable is sufficient for XLR compilation, the
variable NLM_XLR can be removed.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2962/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since commit [e58aa3d2: genirq: Run irq handlers with interrupts disabled],
We run all interrupt handlers with interrupts disabled and we even check
and yell when an interrupt handler returns with interrupts enabled (see
commit [b738a50a: genirq: Warn when handler enables interrupts]).
So now this flag is a NOOP and can be removed.
[ralf@linux-mips.org: Fixed up conflicts in
arch/mips/alchemy/common/dbdma.c, arch/mips/cavium-octeon/smp.c and
arch/mips/kernel/perf_event.c.]
Signed-off-by: Yong Zhang <yong.zhang0@gmail.com>
To: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.delinux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2835/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move add_wired_entry to its own header file from where it will be
always included. Patch up other users of add_wired_entry to also include
the header as needed.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Panic() invokes printk() to add a \n internally, so panic arguments should
not themselves end in \n. Panic invocations in arch/mips and elsewhere
are inconsistently sometimes terminating in \n, sometimes not.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move PCI Controller PM to syscore_ops since the platform_driver PM methods
are called way too late on resume and far too early on suspend (after and
before PCI device resume/suspend).
This also allows to simplify wired entry management a bit.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/3007/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code located at arch/mips/lantiq/ included module.h to be able to use
the EXPORT_SYMBOL* macros. These can now be directly included using
export.h.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2937/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'modsplit-Oct31_2011' of git://git.kernel.org/pub/scm/linux/kernel/git/paulg/linux: (230 commits)
Revert "tracing: Include module.h in define_trace.h"
irq: don't put module.h into irq.h for tracking irqgen modules.
bluetooth: macroize two small inlines to avoid module.h
ip_vs.h: fix implicit use of module_get/module_put from module.h
nf_conntrack.h: fix up fallout from implicit moduleparam.h presence
include: replace linux/module.h with "struct module" wherever possible
include: convert various register fcns to macros to avoid include chaining
crypto.h: remove unused crypto_tfm_alg_modname() inline
uwb.h: fix implicit use of asm/page.h for PAGE_SIZE
pm_runtime.h: explicitly requires notifier.h
linux/dmaengine.h: fix implicit use of bitmap.h and asm/page.h
miscdevice.h: fix up implicit use of lists and types
stop_machine.h: fix implicit use of smp.h for smp_processor_id
of: fix implicit use of errno.h in include/linux/of.h
of_platform.h: delete needless include <linux/module.h>
acpi: remove module.h include from platform/aclinux.h
miscdevice.h: delete unnecessary inclusion of module.h
device_cgroup.h: delete needless include <linux/module.h>
net: sch_generic remove redundant use of <linux/module.h>
net: inet_timewait_sock doesnt need <linux/module.h>
...
Fix up trivial conflicts (other header files, and removal of the ab3550 mfd driver) in
- drivers/media/dvb/frontends/dibx000_common.c
- drivers/media/video/{mt9m111.c,ov6650.c}
- drivers/mfd/ab3550-core.c
- include/linux/dmaengine.h
Or else we get lots of variations on this:
arch/mips/pci/pci.c:330: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL'
scattered throughout the build.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
The bits used to set the PCI bus speed on AR9 are slightly different to
those used on Danube.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2614/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/pci/pci-rc32434.c: In function 'rc32434_pci_init':
arch/mips/pci/pci-rc32434.c:217:16: error: 'rcrc32434_res_pci_io1' undeclared (first use in this function)
arch/mips/pci/pci-rc32434.c:217:16: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-rc32434.o] Error 1
This problem is included in the following commit.
commit 28f65c11f2
Author: Joe Perches <joe@perches.com>
Date: Thu Jun 9 09:13:32 2011 -0700
treewide: Convert uses of struct resource to resource_size(ptr)
Signed-off-by: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: linux-mips <linux-mips@linux-mips.org>
Cc: Joe Perches <joe@perches.com>
Patchwork: https://patchwork.linux-mips.org/patch/2654/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several fixes as well where the +1 was missing.
Done via coccinelle scripts like:
@@
struct resource *ptr;
@@
- ptr->end - ptr->start + 1
+ resource_size(ptr)
and some grep and typing.
Mostly uncompiled, no cross-compilers.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The Lantiq family of SoCs have a EBU (External Bus Unit). This patch adds
the driver that allows us to use the EBU as a PCI controller. In order for
PCI to work the EBU is set to endianess swap all the data. In addition we
need to make use of SWAP_IO_SPACE for device->host DMA to work.
The clock of the PCI works in several modes (internal/external). If this
is not configured correctly the SoC will hang.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralph Hempel <ralph.hempel@lantiq.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2250/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds pci/pci-xlr.c to support for XLR PCI/PCI-X interface and XLS PCIe
interface.
Update irq.c to ack PCI interrupts, use irq handler data to do the
PCI/PCIe bus ack.
Signed-off-by: Jayachandran C <jayachandranc@netlogicmicro.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2337/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This includes conversion to new style irq_chip functions, and
correctly enabling/disabling per-CPU interrupts.
The hardware interrupt bit to irq number mapping is now done with a
flexible map, instead of by bit twiddling the irq number.
[ tglx: Adjusted to new irq_cpu_on/offline callbacks and
__irq_set_affinity_lock ]
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Cc: linux-mips@linux-mips.org
Cc: ralf@linux-mips.org
LKML-Reference: <1301081931-11240-5-git-send-email-ddaney@caviumnetworks.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
All Octeon chips can support more than 4GB of RAM. Also due to how Octeon
PCI is setup, even some configurations with less than 4GB of RAM will have
portions that are not accessible from 32-bit devices.
Enable the swiotlb code to handle the cases where a device cannot directly
do DMA. This is a complete rewrite of the Octeon DMA mapping code.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1639/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add missing #inclusions of <linux/irq.h> to a whole bunch of files that should
really include it. Note that this can replace #inclusions of <asm/irq.h>.
This is required for the patch to sort out irqflags handling function naming to
compile on MIPS.
The problem is that these files require access to things like setup_irq() -
which isn't available by #including <linux/interrupt.h>
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
We reserve the 3.75GB - 4GB region of PCIe address space for device to
device transfers, making the corresponding physical memory under
direct mapping unavailable for DMA.
To allow for PCIe DMA to all physical memory we map this chunk of
physical memory with BAR1. Because of the resulting discontinuity in
the mapping function, we remove a page of memory at each end of the
range so multi-page DMA buffers can never be allocated that span the
range.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1535/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MSI-X interrupts are not supported yet for Octeon, return error if
MSI-X interrupts are requested by driver so that the driver will fall
back to use MSI interrupts.
Signed-off-by: Chandrakala Chavva <cchavva@caviumnetworks.com>
To: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: https://patchwork.linux-mips.org/patch/1506/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
The use of handle_percpu_irq() is not really what we want for MSI, use
handle_simple_irq() instead. This is probably the prototypical case
for using handle_simple_irq(), because all the MSIs are dispatched from
the root interrupt service routine.
Also since the base IRQ is not shared, don't pass IRQF_SHARED.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1488/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
MSI IRQ numbers are allocated dynamically, so there is no reason to
have all these static definitions.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1487/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Put all the MSI code in one place (msi-octeon.c). This simplifies
octeon-irq.c and gets rid of some ugly #ifdefs
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/1484/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Several MIPS platforms don't set pci_controller::io_map_base for their
PCI bridges. This results in a panic in pci_iomap(). (The panic is
conditional on CONFIG_PCI_DOMAINS, but that is now enabled for all PCI
MIPS systems.)
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Cc: linux-mips@linux-mips.org
Cc: Martin Michlmayr <tbm@cyrius.com>
Cc: Aurelien Jarno <aurelien@aurel32.net>
Cc: 584784@bugs.debian.org
Patchwork: https://patchwork.linux-mips.org/patch/1377/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
| arch/mips/pci/pci-sb1250.c: In function sb1250_pcibios_init:
| arch/mips/pci/pci-sb1250.c:257: warning: assignment makes integer from pointer without a cast
| arch/mips/pci/pci-sb1250.c:285: error: MAX_NR_CONSOLES undeclared (first use in this function)
| arch/mips/pci/pci-sb1250.c:285: error: (Each undeclared identifier is reported only once
| arch/mips/pci/pci-sb1250.c:285: error: for each function it appears in.)
Signed-off-by: Sebastian Andrzej Siewior <sebastian@breakpoint.cc>
Cc: linux-mips@linux-mips.org
Patchwork: http://patchwork.linux-mips.org/patch/1136/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
On Lemote 2F CS5536 MSRs are accessed through a index / data register pair.
The access sequence must be protected by a spinlock to be atomic.
Without this rebooting in fs2f_reboot() may fail.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: linux-mips@linux-mips.org
Cc: David Daney <ddaney@caviumnetworks.com>
Patchwork: http://patchwork.linux-mips.org/patch/1058/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
The GT-64111 PCI host bridge has no address translation mechanism, so
it can't generate legacy port accesses. This quirk fixes legacy device
port resources to contain the bus addresses actually generated by the
GT-64111.
I think this is the approach Ben Herrenschmidt suggested long ago:
http://marc.info/?l=linux-kernel&m=119733290624544&w=2
This allows us to remove the IORESOURCE_PCI_FIXED hack from
pcibios_fixup_device_resources(), which converts bus addresses to CPU
addresses. IORESOURCE_PCI_FIXED denotes resources that can't be moved;
it has nothing to do with converting bus to CPU addresses.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: linux-mips@linux-mips.org
Tested-by: Yoichi Yuasa <yuasa@linux-mips.org>
Patchwork: http://patchwork.linux-mips.org/patch/998/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
To: linux-mips@linux-mips.org
To: Andrew Morton <akpm@linux-foundation.org>
To: LKML <linux-kernel@vger.kernel.org>
Patchwork: http://patchwork.linux-mips.org/patch/860/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Now that we return the new resource start position, there is no
need to update "struct resource" inside the align function.
Therefore, mark the struct resource as const.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
As suggested by Linus, align functions should return the start
of a resource, not void. An update of "res->start" is no longer
necessary.
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The platform has never been fully merged
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Thomas Koeller <thomas.koeller@baslerweb.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Wim Van Sebroeck <wim@iguana.be>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mtd@lists.infradead.org
Acked-by: David Woodhouse <David.Woodhouse@intel.com>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
PCI support for the Fuloong 2E and Lemote Loongson 2F family machines is
mostly identical with the exception of CS5536 support.
Rename ops-fuloong2e.c to ops-loongson2.c then add the CS5536 support to
share most of the source code among Loongson machines.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: zhangfx@lemote.com
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Nicholas Mc Guire <hofrat@hofr.at>
Cc: Arnaud Patard <apatard@mandriva.com>
Cc: loongson-dev@googlegroups.com
Cc: linux-mips@linux-mips.org
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The built-in Loongson 2E/2F northbridge in is bonito64-compatible but not
identical with it. To avoid influencing the original bonito64 support and
make the loongson support more maintainable, it's better to separate the
Bonito64 code from the Loongson code.
This also prepares the kernel for the coming Loongson 2f machines family
support.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Cc: yanh@lemote.com
Cc: huhb@lemote.com
Cc: Zhang Le <r0bertz@gentoo.org>
Cc: zhangfx@lemote.com,
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Produce an error if request_irq() fails.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Cc: "Ithamar R. Adema" <ithamar.adema@team-embedded.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
To make source code of loongson sharable to the machines(such as gdium)
made by the other companies, we rename arch/mips/lemote to
arch/mips/loongson, asm/mach-lemote to asm/mach-loongson, and rename lm2e
to the name of the machine: fuloong-2e. accordingly, FULONG are renamed to
FULOONG2E to make it distinguishable to the future FULOONG2F. and also,
some other relative tuning is needed.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the help of script/checkpatch.pl, i have cleaned up the coding
style.
1. remove un-needed header files and tune some comments.
2. remove some un-needed { }
add a new header file loongson.h:
3. move some common header files to loongson.h
4. move some common extern declartions to loongson.h
and this new header file is needed for future loongson2f support.
Signed-off-by: Wu Zhangjin <wuzj@lemote.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some SiliconImage PCIe SATA controlers are not detected when the bus
numbers differ.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They tend to get not updated when files are moved around or copied and
lack any obvious use. While at it zap some only too obvious comments and
as per Shinya's suggestion, add a copyright header to extable.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Acked-by: Thadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Move the cavium PCI files to the arch/mips/pci directory. Also cleanup
comment formatting and code layout. Code from pci-common.c, was moved
into other files.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Some of the were relying into smp.h being dragged in by another header
which of course is fragile. <asm/cpu-info.h> uses smp_processor_id()
only in macros and including smp.h there leads to an include loop, so
don't change cpu-info.h.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The code is rather based on trial-and-error than knowledge. Verified Via
Rhine functionality in PIO as well as MMIO mode.
[Looks sane -- Ralf]
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Tested-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use the generic pci_common_swizzle() instead of arch-specific code.
Note that pci_common_swizzle() loops based on dev->bus->self, not
dev->bus->parent as the mips common_swizzle() did. I think they
are equivalent for this purpose.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Certain X11 servers such as the SIS server will only work if PCI mmap is
implemented. This patch implements PCI mmap but to be on the same side
so close to a release it only supports uncached mappings so performance
will not be optimal for some uses such as framebuffers.
Thanks to Zhang Le <r0bertz@gentoo.org> for the original report and
testing.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We'll put all EMMA related headers there in the future.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- Move EMMA related stuff into arch/mips/emma/Kconfig
- Create CONFIG_SOC_EMMA* to handle more EMMA SoCs effectively
- Rename CONFIG_MARKEINS into CONFIG_NEC_MARKEINS
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi@necel.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
mips/pci/fixup-rc32434.c must #include <asm/mach-rc32434/irq.h>
This patch fixes the following compile error caused by
commit 606a083b1e
(MIPS: RB532: Cleanup the headers again):
<-- snip -->
...
CC arch/mips/pci/fixup-rc32434.o
arch/mips/pci/fixup-rc32434.c: In function 'pcibios_map_irq':
arch/mips/pci/fixup-rc32434.c:46: error: 'GROUP4_IRQ_BASE' undeclared (first use in this function)
arch/mips/pci/fixup-rc32434.c:46: error: (Each undeclared identifier is reported only once
arch/mips/pci/fixup-rc32434.c:46: error: for each function it appears in.)
make[2]: *** [arch/mips/pci/fixup-rc32434.o] Error 1
<-- snip -->
A virtually identical patch was also submitted by Yoichi Yuasa
<yoichi_yuasa@tripeaks.co.jp>.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The patch below changes register_pci_controller() such that controllers
being added after pcibios_init() has run are be scanned immediately.
This is needed for example by the BCM47xx PCI controller, which is located
on the SSB bus, which is now initialized after the PCI subsystem.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
