Patch from Nicolas Pitre
Without this some devices fail to work again after a suspend event.
Signed-off-by: Nicolas Pitre
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The initial IB2 addresses did not depend on the IB2 base. This
patch defines them as (VERSATILE_IB2_BASE + offset).
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The GPIO base for Integrator/CP is different from the
Integrator/AP. This patch sets the correct value for
INTEGRATOR_GPIO_BASE.
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Catalin Marinas
The current red and blue colours on the Versatile CLCD are
reversed when the 5:6:5 mode is used. The patch sets the proper
bit in the SYS_CLCD register value.
Signed-off-by: Catalin Marinas
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It looks like logic for enabling hardware tapping in ALPS driver was
inverted and we enable it only if it was already enabled by BIOS or
firmware.
I have a confirmation from one user that the patch below fixes the problem
for him and it might be beneficial if we could get it into 2.6.12.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ELF core dump code has one use of off_t when writing out segments.
Some of the segments may be passed the 2GB limit of an off_t, even on a
32-bit system, so it's important to use loff_t instead. This fixes a
corrupted core dump in the bigcore test in GDB's testsuite.
Signed-off-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixed a problem that showed up in the Fedora development tree a few
weeks before the Fedora Core 4 release, initially as slab corruption, later
as hard crashes on boot up, when slab debugging was disabled for the
release. More details on the history at
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=158424
The problem is caused by sbp2's use of scsi_host->hostdata[0] to hold a
scsi_id, without explicitly requesting space for it. Since hostdata is
declared as a zero-sized array, we don't get any such space by default, so
it must be explicitly requested. The patch below implements just that.
Signed-off-by: Alexandre Oliva <aoliva@redhat.com>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
__elv_add_request(). rq.count[READ] + rq.count[WRITE] can increase
more than one if another thread has allocated a request after the
current request is allocated or in_flight could have changed resulting
in larger-than-one change of nrq, thus breaking the threshold
mechanism.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Tejun Heo <htejun@gmail.com>
This fixes various crashes on 64-bit when using this module.
Based upon a patch by Juergen Kreileder <jk@blackdown.de>.
Signed-off-by: David S. Miller <davem@davemloft.net>
ACKed-by: Patrick McHardy <kaber@trash.net>
enable cpusets
enable new lpfc and jsm drivers
enable new dm-multipath
leave new agp disabled
disable rivafb, it does not handle the cards in G5 models (FX5200 as example)
the new nvidiafb doesnt work on bigendian, yet
Signed-off-by: Olaf Hering <olh@suse.de>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is a patch to update the example configs in arch/ppc64/configs.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this patch, some usb kobjects, which are parents to the usx2y's
kobjects can be freed before the usx2y's. This led to an oops in
get_kobj_path_length() and a dead keyboard, when the usx2y's kobjects
were freed. The patch ensures the correct sequence. Tested ok on
kernel 2.6.12-rc2.
Present in ALSA cvs
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Without this patch, some usb kobjects, which are parents to the usx2y's
kobjects can be freed before the usx2y's. This led to an oops in
get_kobj_path_length() and a dead keyboard, when the usx2y's kobjects
were freed. The patch ensures the correct sequence. Tested ok on
kernel 2.6.12-rc2.
Present in ALSA cvs
Signed-off-by: Karsten Wiese <annabellesgarden@yahoo.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Chris Wright <chrisw@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch causes the ignore_normal_resume flag to be set slightly earlier,
before there is a chance that the apm driver will receive the normal resume
event from the BIOS. (Addresses Debian bug #310865)
Signed-off-by: Thomas Hood <jdthood@yahoo.co.uk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixed freeing of event memory in i2o_block_event()
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It prints out x,x instead of x,y.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Cc: "Antonino A. Daplas" <adaplas@hotpop.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On one path, cond_resched_lock() fails to return true if it dropped the lock.
We think this might be causing the crashes in JBD's log_do_checkpoint().
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
On 64-bit machines, PCI_BASE_ADDRESS_MEM_MASK and other mask constants
passed to pci_size() are 64-bit (for example ~0x0fUL). However, pci_size
does comparisons between the u32 arguments and the mask, which will fail
even though any result from pci_size is still just 32-bit.
Changing the mask argument to u32 seems the obvious thing to do, since all
arithmetic in the function is 32-bit and having a larger mask makes no
sense.
This triggered on a PPC64 system here where an adapter (VGA, as it
happened) had a memory region base of 0xfe000000 and a sz of the same,
matching the if (max == maxbase ...) test at the bottom of pci_size but
failing the mask comparison. Quite a corner case which I guess explains
why we haven't seen it until now.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch merges a lot of duplicated code in the slip and slirp drivers,
abstracts out the slip protocol, and makes the slip driver work in 2.6.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert the boot-time host ptrace testing from clone to fork. They were
essentially doing fork anyway. This cleans up the code a bit, and makes
valgrind a bit happier about grinding it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a build failure when CONFIG_MODE_SKAS is disabled and make a Makefile
comment fit in 80 columns.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A few files include the same header twice.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Following the go around over the SONY DVD that needs artificial limits,
this should be the correct code for all cases (minus the debugging
prints).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Heiko Carstens <heiko.carstens@de.ibm.com>
Fixes module parameter parsing for "device" parameter. The original
module parameter was changed while parsing it. This corrupted the
output in sysfs (/sys/module/zfcp/parameters/device).
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes a race between zfcp_fsf_req_dismiss_all and
zfcp_qdio_reqid_check. During adapter shutdown it occurred that a
request was cleaned up twice. First during its normal
completion. Second when dismiss_all was called. The fix is to
serialize access to fsf request list between zfcp_fsf_req_dismiss_all
and zfcp_qdio_reqid_check and delete a fsf request from the list if
its completion is triggered. (Additionally a rwlock was replaced by a
spinlock and fsf_req_cleanup was eliminated.)
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Fixes a bug in zfcp_send_els_handler. If D_ID assignments for ports
are changing between initiation of one ELS request and its completion
the wrong port might be accessed in the completion for that ELS
request. Thus a pointer to the port has to be passed for ELS requests
to identify the port structure if required.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Correct a bug in zfcp_fsf_send_fcp_command_handler. An fsf request
was not marked as failed if an unknown status qualifier was returned.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Reopen a remote port only if the link-test fails. This avoids that a
port is unnecessarily reopened.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: Maxim Shchetynin <maxim@de.ibm.com>
Extend the time for adapter initialization: In case of protocol
status HOST_CONNECTION_INITIALIZING for the exchange config data
command do a first retry in 1 second, then double the sleep time for
each following retry until recovery exceeds 2 minutes. The old
behaviour of allowing 6 retries with .5 seconds delay between retries
was insufficient and qdio queues were shut down too erarly.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fixes the handling of failed requests for GID_PN nameserver command:
Set ZFCP_STATUS_PORT_INVALID_WWPN only if indicated by response
payload for GID_PN nameserver command and not if fsf request fails.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This adds a clause that notes explicitly that the person doing the
sign-off knows that the project (and his sign-off) is public and will
possibly get archived and re-distributed.
This patch alows you to change the source address of icmp error
messages. It applies cleanly to 2.6.11.11 and retains the default
behaviour.
In the old (default) behaviour icmp error messages are sent with the ip
of the exiting interface.
The new behaviour (when the sysctl variable is toggled on), it will send
the message with the ip of the interface that received the packet that
caused the icmp error. This is the behaviour network administrators will
expect from a router. It makes debugging complicated network layouts
much easier. Also, all 'vendor routers' I know of have the later
behaviour.
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Yasevich <vladislav.yasevich@hp.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Userland layer-2 tunneling devices allocated through the TUNTAP driver
(drivers/net/tun.c) have a type of ARPHRD_NONE, and have no link-layer
address. The kernel complains at regular interval when IPv6 Privacy
extension are enabled because it can't find an hardware address :
Dec 29 11:02:04 auguste kernel: __ipv6_regen_rndid(idev=cb3e0c00):
cannot get EUI64 identifier; use random bytes.
IPv6 Privacy extensions should probably be disabled on that sort of
device. They won't work anyway. If userland wants a more usual
Ethernet-ish interface with usual IPv6 autoconfiguration, it will use a
TAP device with an emulated link-layer and a random hardware address
rather than a TUN device.
As far as I could fine, TUN virtual device from TUNTAP is the very only
sort of device using ARPHRD_NONE as kernel device type.
Signed-off-by: Rémi Denis-Courmont <rdenis@simphalempin.com>
Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We saw following trace several times:
|BUG: using smp_processor_id() in preemptible [00000001] code: httpd/30137
|caller is icmpv6_send+0x23/0x540
| [<c01ad63b>] smp_processor_id+0x9b/0xb8
| [<c02993e7>] icmpv6_send+0x23/0x540
This is because of icmpv6_socket, which is the only one user of
smp_processor_id() in icmpv6_send(), AFAIK.
Since it should be used in non-preemptive context,
let's defer the dereference after disabling preemption
(by icmpv6_xmit_lock()).
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
