Alex writes:
"A few more radeon fixes for 3.8. Mostly small stuff. The big
change is disabling the use of the DMA ring for VM PT updates. This
reverts back to the 3.7 behavior. Problem is we can get huge PT
updates in certain cases that are too big for the DMA ring. I've
got patches to use an IB for this so I can re-enable the use of the
DMA ring for VM PT updates in 3.9. This request also includes the
patches from the last pull request I sent on Monday in case you haven't
pulled them yet."
* 'drm-fixes-3.8' of git://people.freedesktop.org/~agd5f/linux:
drm/radeon: switch back to the CP ring for VM PT updates
drm/radeon: prevent crash in the ring space allocation
drm/radeon: Calling object_unrefer() when creating fb failure
drm/radeon/r5xx-r7xx: wait for the MC to settle after MC blackout
drm/radeon/evergreen+: wait for the MC to settle after MC blackout
drm/radeon: protect against div by 0 in backend setup
drm/radeon: fix backend map setup on 1 RB sumo boards
drm/radeon: add quirk for RV100 board
drm/radeon: add WAIT_UNTIL to the non-VM safe regs list for cayman/TN
drm/radeon: fix MC blackout on evergreen+
This patch fixes a possible divide by zero bug when the fabric_max_sectors
device attribute is written and backend se_device failed to be successfully
configured -> enabled.
Go ahead and use block_size=512 within se_dev_set_fabric_max_sectors()
in the event of a target_configure_device() failure case, as no valid
dev->dev_attrib.block_size value will have been setup yet.
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch fixes a v3.8-rc1 regression bug where an unconfigured se_device
was incorrectly allowed to perform a fabric port-link. This bug was
introduced in commit:
commit 0fd97ccf45
Author: Christoph Hellwig <hch@infradead.org>
Date: Mon Oct 8 00:03:19 2012 -0400
target: kill struct se_subsystem_dev
which ended up dropping the original se_subsystem_dev->se_dev_ptr check
preventing this from happening with pre commit 0fd97ccf code.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
PullHID fixes from Jiri Kosina:
- fix i2c-hid and hidraw interaction, by Benjamin Tissoires
- a quirk to make a particular device (Formosa IR receiver) work
properly, by Nicholas Santos
* 'for-3.8/upstream-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
HID: i2c-hid: fix i2c_hid_output_raw_report
HID: usbhid: quirk for Formosa IR receiver
HID: remove x bit from sensor doc
- Error reporting in nfs_xdev_mount incorrectly maps all errors to ENOMEM
- Fix an NFSv4 refcounting issue
- Fix a mount failure when the server reboots during NFSv4 trunking discovery
- NFSv4.1 mounts may need to run the lease recovery thread.
- Don't silently fail setattr() requests on mountpoints
- Fix a SUNRPC socket/transport livelock and priority queue issue
- We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)
iQIcBAABAgAGBQJRCpS4AAoJEGcL54qWCgDyqucP/2CTv5leu+X5/0PXBOykAIHg
8oEsTEz7/4IvIxTXzuHDYirMnm/mulfGF6NrdPqfvxpAHqRfVBfLFocfNLMVhQci
97RmBfEEGM22AToYUubML5bIxr0QllV4s9Vmyh/zGDan52y7zNNlZX+v6aLjZbJB
Fbolihpcch6lhQEUNAzK0B0ddimDl9lazx/WTmMOD/JrwOqzA4FJC+YxBe88nfzQ
c6sYyEptBaSirbCOlueqGpv8skB1CLpFJXguXToPXFxpWed6uoGrIwLO7MLUdFpJ
Xw+j8cuv/wjyYJGVKjhW7kXtwK8T7+u4bT2L883R01XYXr8XfkkLON0dgG1X/unk
80mLzCO1+qRdoDSQ4b/V4B0nScPRCJuoZpftjCi2uhKewNcxQPMZ2V5/D7pO3uyE
NdhxByB8D86JfNrIcBcRaxfuiQsurQBDvsDNmWPBZSOmH/dmHqTQGLcIe6N94A0B
c7KFtXrN2MzOl8S68dUpbhftObq9X0oK2oxFFLWRQoqjrFtiDLU5JilV0bEH2CMo
gJX7CRrPoJ2wmNToKdPJRWBYDmtMMIThq3vIpCj1FFzX17r5grJpqCmp/TViu/ER
r8rmJzni+nmHaO1NLJMTCHzLJ8soiKyBq8PZKAbipTJxy+TXI/69jnWzpIQ/pbM/
JN+0tiCcqmUmXsO+hrCP
=lWFV
-----END PGP SIGNATURE-----
Merge tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs
Pull NFS client bugfixes from Trond Myklebust:
- Error reporting in nfs_xdev_mount incorrectly maps all errors to
ENOMEM
- Fix an NFSv4 refcounting issue
- Fix a mount failure when the server reboots during NFSv4 trunking
discovery
- NFSv4.1 mounts may need to run the lease recovery thread.
- Don't silently fail setattr() requests on mountpoints
- Fix a SUNRPC socket/transport livelock and priority queue issue
- We must handle NFS4ERR_DELAY when resetting the NFSv4.1 session.
* tag 'nfs-for-3.8-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFSv4.1: Handle NFS4ERR_DELAY when resetting the NFSv4.1 session
SUNRPC: When changing the queue priority, ensure that we change the owner
NFS: Don't silently fail setattr() requests on mountpoints
NFSv4.1: Ensure that nfs41_walk_client_list() does start lease recovery
NFSv4: Fix NFSv4 trunking discovery
NFSv4: Fix NFSv4 reference counting for trunked sessions
NFS: Fix error reporting in nfs_xdev_mount
Pull MIPS updates from Ralf Baechle:
"A number of fixes all across the MIPS tree. No area is particularly
standing out and things have cooled down quite nicely for a release."
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Function tracer: Fix broken function tracing
mips: Move __virt_addr_valid() to a place for MIPS 64
MIPS: Netlogic: Fix UP compilation on XLR
MIPS: AR71xx: Fix AR71XX_PCI_MEM_SIZE
MIPS: AR724x: Fix AR724X_PCI_MEM_SIZE
MIPS: Lantiq: Fix cp0_perfcount_irq mapping
MIPS: DSP: Fix DSP mask for registers.
MIPS: Fix build failure by adding definition of pfn_pmd().
MIPS: Octeon: Fix warning.
MIPS: delay.c: Check BITS_PER_LONG instead of __SIZEOF_LONG__
MIPS: PNX833x: Fix comment.
MIPS: Add struct p_format to union mips_instruction.
MIPS: Export <asm/break.h>.
MIPS: BCM47xx: Enable SSB prerequisite SSB_DRIVER_PCICORE.
MIPS: BCM47xx: Select GPIOLIB for BCMA on bcm47xx platform
MIPS: vpe.c: Fix null pointer dereference in print arguments.
For large VM page table updates, we can sometimes generate
more packets than there is space on the ring. This happens
more readily with the DMA ring since it is 64K (vs 1M for the
CP). For now, switch back to the CP. For the next kernel,
I have a patch to utilize IBs for VM PT updates which
alleviates this problem.
Fixes:
https://bugs.freedesktop.org/show_bug.cgi?id=58354
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
If the requested number of DWs on the ring is larger than
the size of the ring itself, return an error.
In testing with large VM updates, we've seen crashes when we
try and allocate more space on the ring than the total size
of the ring without checking.
This prevents the crash but for large VM updates or bo moves
of very large buffers, we will need to break the transaction
down into multiple batches. I have patches to use IBs for
the next kernel.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
When kzalloc() failed in radeon_user_framebuffer_create(), need to
call object_unreference() to match the object_reference().
Signed-off-by: liu chuansheng <chuansheng.liu@intel.com>
Signed-off-by: xueminsu <xuemin.su@intel.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
Some chips seem to need a little delay after blacking out
the MC before the requests actually stop. Stop DMAR errors
reported by Shuah Khan.
Reported-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
It's OK to get kick before backend is set or after
it is cleared, we can just ignore it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
On receiving the SYN-ACK, Fast Open checks icsk_retransmit for SYN
retransmission to detect SYN/data drops. But if F-RTO is disabled,
icsk_retransmit is reset at step D of tcp_fastretrans_alert() (
under tcp_ack()) before tcp_rcv_fastopen_synack(). The fix is to use
total_retrans instead which accounts for SYN retransmission regardless
the use of F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
l2tp_ip6 is incorrectly using the IPv4-specific ip_cmsg_recv to handle
ancillary data. This means that socket options such as IPV6_RECVPKTINFO are
not honoured in userspace.
Convert l2tp_ip6 to use the IPv6-specific handler.
Ref: net/ipv6/udp.c
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: Chris Elston <celston@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip6_datagram_recv_ctl and ip6_datagram_send_ctl are used for handling IPv6
ancillary data. Since ip6_datagram_send_ctl is already publicly exported for
use in modules, ip6_datagram_recv_ctl should also be available to support
ancillary data in the receive path.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The datagram_*_ctl functions in net/ipv6/datagram.c are IPv6-specific. Since
datagram_send_ctl is publicly exported it should be appropriately named to
reflect the fact that it's for IPv6 only.
Signed-off-by: Tom Parkin <tparkin@katalix.com>
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If occurs a LE or SCO hci_conn timeout and the connection is already
established (BT_CONNECTED state), the connection is not terminated as
expected. This bug can be reproduced using l2test or scotest tool.
Once the connection is established, kill l2test/scotest and the
connection won't be terminated.
This patch fixes hci_conn_disconnect helper so it is able to
terminate LE and SCO connections, as well as ACL.
Signed-off-by: Andre Guedes <andre.guedes@openbossa.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
The conn->smp_chan pointer can be NULL if SMP PDUs arrive at unexpected
moments. To avoid NULL pointer dereferences the code should be checking
for this and disconnect if an unexpected SMP PDU arrives. This patch
fixes the issue by adding a check for conn->smp_chan for all other PDUs
except pairing request and security request (which are are the first
PDUs to come to initialize the SMP context).
Signed-off-by: Johan Hedberg <johan.hedberg@intel.com>
CC: stable@vger.kernel.org
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
i2c_hid_output_raw_report is used by hidraw to forward set_report requests.
The current implementation of i2c_hid_set_report needs to take the
report_id as an argument. The report_id is stored in the first byte
of the buffer in argument of i2c_hid_output_raw_report.
Not removing the report_id from the given buffer adds this byte 2 times
in the command, leading to a non working command.
Reported-by: Andrew Duggan <aduggan@synaptics.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Function tracing is currently broken for all 32 bit MIPS platforms.
When tracing is enabled, the kernel immediately hangs on boot.
This is a result of commit b732d439cb
that changes the kernel/trace/Kconfig file so that is no longer
forces FRAME_POINTER when FUNCTION_TRACING is enabled.
MIPS frame pointers are generally considered to be useless because
they cannot be used to unwind the stack. Unfortunately the MIPS
function tracing code has bugs that are masked by the use of frame
pointers. This commit fixes the bugs so that MIPS frame pointers
don't need to be enabled.
The bugs are a result of the odd calling sequence used to call the trace
routine. This calling sequence is inserted into every traceable function
when the tracing CONFIG option is enabled. This sequence is generated
for 32bit MIPS platforms by the compiler via the "-pg" flag.
Part of the sequence is "addiu sp,sp,-8" in the delay slot after every
call to the trace routine "_mcount" (some legacy thing where 2 arguments
used to be pushed on the stack). The _mcount routine is expected to
adjust the sp by +8 before returning. So when not disabled, the original
jalr and addiu will be there, so _mcount has to adjust sp.
The problem is that when tracing is disabled for a function, the
"jalr _mcount" instruction is replaced with a nop, but the
"addiu sp,sp,-8" is still executed and the stack pointer is left
trashed. When frame pointers are enabled the problem is masked
because any access to the stack is done through the frame
pointer and the stack pointer is restored from the frame pointer when
the function returns.
This patch writes two nops starting at the address of the "jalr _mcount"
instruction whenever tracing is disabled. This means that the
"addiu sp,sp.-8" will be converted to a nop along with the "jalr". When
disabled, there will be two nops.
This is SMP safe because the first time this happens is during
ftrace_init() which is before any other processor has been started.
Subsequent calls to enable/disable tracing when other CPUs ARE running
will still be safe because the enable will only change the first nop
to a "jalr" and the disable, while writing 2 nops, will only be changing
the "jalr". This patch also stops using stop_machine() to call the
tracer enable/disable routines and calls them directly because the
routines are SMP safe.
When the kernel first boots we have to be able to handle the gcc
generated jalr, addui sequence until ftrace_init gets a chance to run
and change the sequence. At this point mcount just adjusts the stack
and returns. When ftrace_init runs, we convert the jalr/addui to nops.
Then whenever tracing is enabled we convert the first nop to a "jalr
mcount+8". The mcount+8 entry point skips the stack adjust.
[ralf@linux-mips.org: Folded in Steven Rostedt's build fix.]
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: rostedt@goodmis.org
Cc: ddaney.cavm@gmail.com
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/4806/
Patchwork: https://patchwork.linux-mips.org/patch/4841/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When processing write same requests, fix dm to send the configured
number of WRITE SAME requests to the target rather than the number of
discards, which is not always the same.
Device-mapper WRITE SAME support was introduced by commit
23508a96cd ("dm: add WRITE SAME support").
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Commit d3ce884318 "MIPS: Fix modpost error in modules attepting to use
virt_addr_valid()" moved __virt_addr_valid() from a macro in a header
file to a function in ioremap.c. But ioremap.c is only compiled for MIPS
32, and not for MIPS 64.
When compiling for my yeeloong2, which supposedly supports hibernation,
which compiles kernel/power/snapshot.c which calls virt_addr_valid(), I
got this error:
LD init/built-in.o
kernel/built-in.o: In function `memory_bm_free':
snapshot.c:(.text+0x4c9c4): undefined reference to `__virt_addr_valid'
snapshot.c:(.text+0x4ca58): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e44c): undefined reference to `__virt_addr_valid'
kernel/built-in.o: In function `snapshot_write_next':
(.text+0x4e890): undefined reference to `__virt_addr_valid'
make[1]: *** [vmlinux] Error 1
make: *** [sub-make] Error 2
I suspect that __virt_addr_valid() is fine for mips 64. I moved it to
mmap.c such that it gets compiled for mips 64 and 32.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4842/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
thin_io_hints() is blindly copying the queue limits from the thin-pool
which can lead to incorrect limits being set. The fix here simply
deletes the thin_io_hints() hook which leaves the existing stacking
infrastructure to set the limits correctly.
When a thin-pool uses an MD device for the data device a thin device
from the thin-pool must respect MD's constraints about disallowing a bio
from spanning multiple chunks. Otherwise we can see problems. If the raid0
chunksize is 1152K and thin-pool chunksize is 256K I see the following
md/raid0 error (with extra debug tracing added to thin_endio) when
mkfs.xfs is executed against the thin device:
md/raid0:md99: make_request bug: can't convert block across chunks or bigger than 1152k 6688 127
device-mapper: thin: bio sector=2080 err=-5 bi_size=130560 bi_rw=17 bi_vcnt=32 bi_idx=0
This extra DM debugging shows that the failing bio is spanning across
the first and second logical 1152K chunk (sector 2080 + 255 takes the
bio beyond the first chunk's boundary of sector 2304). So the bio
splitting that DM is doing clearly isn't respecting the MD limits.
max_hw_sectors_kb is 127 for both the thin-pool and thin device
(queue_max_hw_sectors returns 255 so we'll excuse sysfs's lack of
precision). So this explains why bi_size is 130560.
But the thin device's max_hw_sectors_kb should be 4 (PAGE_SIZE) given
that it doesn't have a .merge function (for bio_add_page to consult
indirectly via dm_merge_bvec) yet the thin-pool does sit above an MD
device that has a compulsory merge_bvec_fn. This scenario is exactly
why DM must resort to sending single PAGE_SIZE bios to the underlying
layer. Some additional context for this is available in the header for
commit 8cbeb67a ("dm: avoid unsupported spanning of md stripe boundaries").
Long story short, the reason a thin device doesn't properly get
configured to have a max_hw_sectors_kb of 4 (PAGE_SIZE) is that
thin_io_hints() is blindly copying the queue limits from the thin-pool
device directly to the thin device's queue limits.
Fix this by eliminating thin_io_hints. Doing so is safe because the
block layer's queue limits stacking already enables the upper level thin
device to inherit the thin-pool device's discard and minimum_io_size and
optimal_io_size limits that get set in pool_io_hints. But avoiding the
queue limits copy allows the thin and thin-pool limits to be different
where it is important, namely max_hw_sectors_kb.
Reported-by: Daniel Browning <db@kavod.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This adds support for the OWL CM-160 electricity monitor to the cp210x
driver.
Signed-off-by: Luis Llorente <luisllorente@luisllorente.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For some reason they didn't get replaced so far by their
paravirt equivalents, resulting in code to be run with
interrupts disabled that doesn't expect so (causing, in the
observed case, a BUG_ON() to trigger) when syscall auditing is
enabled.
David (Cc-ed) came up with an identical fix, so likely this can
be taken to count as an ack from him.
Reported-by: Peter Moody <pmoody@google.com>
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Link: http://lkml.kernel.org/r/5108E01902000078000BA9C5@nat28.tlf.novell.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: stable@vger.kernel.org
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: David Vrabel <david.vrabel@citrix.com>
Tested-by: Peter Moody <pmoody@google.com>
This patch (as1654) fixes a very old bug in ehci-hcd, connected with
scheduling of periodic split transfers. The calculations for
full/low-speed bus usage are all carried out after the correction for
bit-stuffing has been applied, but the values in the max_tt_usecs
array assume it hasn't been. The array should allow for allocation of
up to 90% of the bus capacity, which is 900 us, not 780 us.
The symptom caused by this bug is that any isochronous transfer to a
full-speed device with a maxpacket size larger than about 980 bytes is
always rejected with a -ENOSPC error.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch (as1653) fixes a bug in ehci-hcd. Unlike iTD entries, an
siTD entry in the periodic schedule may not complete until the frame
after the one it belongs to. Consequently, when scanning the periodic
schedule it is necessary to start with the frame _preceding_ the one
where the previous scan ended.
Not doing this properly can result in memory leaks and failures to
complete isochronous URBs.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Andy Leiserson <andy@leiserson.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For BUCK10 the control registers are wrongly set as buck9 control register
This patch corrects the control registers for buck10
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Pull x86 EFI fixes from Peter Anvin:
"This is a collection of fixes for the EFI support. The controversial
bit here is a set of patches which bumps the boot protocol version as
part of fixing some serious problems with the EFI handover protocol,
used when booting under EFI using a bootloader as opposed to directly
from EFI. These changes should also make it a lot saner to support
cross-mode 32/64-bit EFI booting in the future. Getting these changes
into 3.8 means we avoid presenting an inconsistent ABI to bootloaders.
Other changes are display detection and fixing efivarfs."
* 'x86-efi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86, efi: remove attribute check from setup_efi_pci
x86, build: Dynamically find entry points in compressed startup code
x86, efi: Fix PCI ROM handing in EFI boot stub, in 32-bit mode
x86, efi: Fix 32-bit EFI handover protocol entry point
x86, efi: Fix display detection in EFI boot stub
x86, boot: Define the 2.12 bzImage boot protocol
x86/boot: Fix minor fd leakage in tools/relocs.c
x86, efi: Set runtime_version to the EFI spec revision
x86, efi: fix 32-bit warnings in setup_efi_pci()
efivarfs: Delete dentry from dcache in efivarfs_file_write()
efivarfs: Never return ENOENT from firmware
efi, x86: Pass a proper identity mapping in efi_call_phys_prelog
efivarfs: Drop link count of the right inode
Pull x86 fixes from Peter Anvin:
"This is a collection of miscellaneous fixes, the most important one is
the fix for the Samsung laptop bricking issue (auto-blacklisting the
samsung-laptop driver); the efi_enabled() changes you see below are
prerequisites for that fix.
The other issues fixed are booting on OLPC XO-1.5, an UV fix, NMI
debugging, and requiring CAP_SYS_RAWIO for MSR references, just as
with I/O port references."
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
samsung-laptop: Disable on EFI hardware
efi: Make 'efi_enabled' a function to query EFI facilities
smp: Fix SMP function call empty cpu mask race
x86/msr: Add capabilities check
x86/dma-debug: Bump PREALLOC_DMA_DEBUG_ENTRIES
x86/olpc: Fix olpc-xo1-sci.c build errors
arch/x86/platform/uv: Fix incorrect tlb flush all issue
x86-64: Fix unwind annotations in recent NMI changes
x86-32: Start out cr0 clean, disable paging before modifying cr3/4
Pull console lockdep checking revert from Dave Airlie.
The lockdep splat this showed was interesting, but it's very very old,
and we won't be fixing it until 3.9. In the meantime, undo the lockdep
annotation so that we don't generate the (known) console lockdep issue,
and then possibly hide any potential other (unknown) lockdep problems
that got disabled by the first one that triggered.
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
Revert "console: implement lockdep support for console_lock"
This reverts commit daee779718.
I'll requeue this after the console locking fixes, so lockdep
is useful again for people until fbcon is fixed.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add VID, PID and fixed interface for Telit LE920
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
They will be created at output, if ever needed. This avoids creating
empty neighbor entries when TPROXYing/Forwarding packets for addresses
that are not even directly reachable.
Note that IPv4 already handles it this way. No neighbor entries are
created for local input.
Tested by myself and customer.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Marcelo Ricardo Leitner <mleitner@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NFS4ERR_DELAY is a legal reply when we call DESTROY_SESSION. It
usually means that the server is busy handling an unfinished RPC
request. Just sleep for a second and then retry.
We also need to be able to handle the NFS4ERR_BACK_CHAN_BUSY return
value. If the NFS server has outstanding callbacks, we just want to
similarly sleep & retry.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
This fixes a livelock in the xprt->sending queue where we end up never
making progress on lower priority tasks because sleep_on_priority()
keeps adding new tasks with the same owner to the head of the queue,
and priority bumps mean that we keep resetting the queue->owner to
whatever task is at the head of the queue.
Regression introduced by commit c05eecf636
(SUNRPC: Don't allow low priority tasks to pre-empt higher priority ones).
Reported-by: Andy Adamson <andros@netapp.com>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=QrJx
-----END PGP SIGNATURE-----
Merge tag 'efi-for-3.8' into x86/efi
Various urgent EFI fixes and some warning cleanups for v3.8
* EFI boot stub fix for Macbook Pro's from Maarten Lankhorst
* Fix an oops in efivarfs from Lingzhu Xiang
* 32-bit warning cleanups from Jan Beulich
* Patch to Boot on >512GB RAM systems from Nathan Zimmer
* Set efi.runtime_version correctly
* efivarfs updates
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Ensure that any setattr and getattr requests for junctions and/or
mountpoints are sent to the server. Ever since commit
0ec26fd069 (vfs: automount should ignore LOOKUP_FOLLOW), we have
silently dropped any setattr requests to a server-side mountpoint.
For referrals, we have silently dropped both getattr and setattr
requests.
This patch restores the original behaviour for setattr on mountpoints,
and tries to do the same for referrals, provided that we have a
filehandle...
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: stable@vger.kernel.org
A device sending 0 length frames as fast as it can has been
observed killing the host system due to the resulting memory
pressure.
Temporarily disable RX skb allocation and URB submission when
the current error ratio is high, preventing us from trying to
allocate an infinite number of skbs. Reenable as soon as we
are finished processing the done queue, allowing the device
to continue working after short error bursts.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The commit 2a37b1a "MIPS: Netlogic: Move from u32 cpumask to cpumask_t"
breaks uniprocessor compilation on XLR with:
arch/mips/netlogic/xlr/setup.c: In function 'prom_init':
arch/mips/netlogic/xlr/setup.c:196:6: error: unused variable 'i'
Fix by defining 'i' only when CONFIG_SMP is defined.
Signed-off-by: Jayachandran C <jchandra@broadcom.com>
Patchwork: http://patchwork.linux-mips.org/patch/4760/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The base address of the PCI memory is 0x10000000 and the base address of the
PCI configuration space is 0x17000000 on the AR71xx SoCs.
The AR71XX_PCI_MEM_SIZE is defined as 0x08000000 which is wrong because that
overlaps with the configuration space. This patch fixes the value of the
AR71XX_PCI_MEM_SIZE constant, in order to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4873/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The base address of the PCI memory is
0x10000000 and the base address of the
PCI configuration space is 0x14000000
on the AR724x SoCs.
The AR724X_PCI_MEM_SIZE is defined as
0x08000000 which is wrong because that
overlaps with the configuration space.
The patch fixes the value of the
AR724X_PCI_MEM_SIZE constant, in order
to avoid this resource conflicts.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/4872/
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The introduction of the OF support broke the cp0_perfcount_irq mapping. This
resulted in oprofile not working anymore.
Offending commit is :
commit 3645da0276
Author: John Crispin <blogic@openwrt.org>
Date: Tue Apr 17 10:18:32 2012 +0200
OF: MIPS: lantiq: implement irq_domain support
Signed-off-by: Conor O'Gorman <i@conorogorman.net>
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/4875/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It has been reported that running this driver on some Samsung laptops
with EFI can cause those machines to become bricked as detailed in the
following report,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
There have also been reports of this driver causing Machine Check
Exceptions on recent EFI-enabled Samsung laptops,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
So disable it if booting from EFI since this driver relies on
grovelling around in the BIOS memory map which isn't going to work.
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Originally 'efi_enabled' indicated whether a kernel was booted from
EFI firmware. Over time its semantics have changed, and it now
indicates whether or not we are booted on an EFI machine with
bit-native firmware, e.g. 64-bit kernel with 64-bit firmware.
The immediate motivation for this patch is the bug report at,
https://bugs.launchpad.net/ubuntu-cdimage/+bug/1040557
which details how running a platform driver on an EFI machine that is
designed to run under BIOS can cause the machine to become
bricked. Also, the following report,
https://bugzilla.kernel.org/show_bug.cgi?id=47121
details how running said driver can also cause Machine Check
Exceptions. Drivers need a new means of detecting whether they're
running on an EFI machine, as sadly the expression,
if (!efi_enabled)
hasn't been a sufficient condition for quite some time.
Users actually want to query 'efi_enabled' for different reasons -
what they really want access to is the list of available EFI
facilities.
For instance, the x86 reboot code needs to know whether it can invoke
the ResetSystem() function provided by the EFI runtime services, while
the ACPI OSL code wants to know whether the EFI config tables were
mapped successfully. There are also checks in some of the platform
driver code to simply see if they're running on an EFI machine (which
would make it a bad idea to do BIOS-y things).
This patch is a prereq for the samsung-laptop fix patch.
Cc: David Airlie <airlied@linux.ie>
Cc: Corentin Chary <corentincj@iksaif.net>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Peter Jones <pjones@redhat.com>
Cc: Colin Ian King <colin.king@canonical.com>
Cc: Steve Langasek <steve.langasek@canonical.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Konrad Rzeszutek Wilk <konrad@kernel.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: <stable@vger.kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
A scan request is split into multiple scan commands queued in
scan_pending_q. Each scan command will be sent to firmware and
its response is handlded one after another.
If any error is detected while parsing IE in command response
buffer the remaining data will be ignored and error is returned.
We should check if there is any more scan commands pending in
the queue before returning error. This ensures that we will call
cfg80211_scan_done if this is the last scan command, or send
next scan command in scan_pending_q to firmware.
Cc: "3.6+" <stable@vger.kernel.org>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=G34+
-----END PGP SIGNATURE-----
Merge tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fixlets from Borislav Petkov:
"Two minor correctness fixlets from Dan Carpenter and Joe Perches each."
* tag 'edac_for_3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC: Fix kcalloc argument order
EDAC: Test correct variable in ->store function
- A collection of small ASoC driver fixes (error path fixes, register
correction, regulator bypass mode fix, etc)
- A few regression fixes and quirks of HD-audio (wrong page attributes
for SG-buffer, Poulsbo/Oaktrail controller fix, digital mic fix for
Acer, etc)
- A fix for USB-audio UAC2 devices wrt FU length check
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=mySP
-----END PGP SIGNATURE-----
Merge tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound fixes from Takashi Iwai:
- A collection of small ASoC driver fixes (error path fixes, register
correction, regulator bypass mode fix, etc)
- A few regression fixes and quirks of HD-audio (wrong page attributes
for SG-buffer, Poulsbo/Oaktrail controller fix, digital mic fix for
Acer, etc)
- A fix for USB-audio UAC2 devices wrt FU length check
* tag 'sound-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix non-snoop page handling
ALSA: hda - Enable LPIB delay count for Poulsbo / Oaktrail
ALSA: hda - fix inverted internal mic on Acer AOA150/ZG5
ALSA: usb-audio: fix invalid length check for RME and other UAC 2 devices
ALSA: hda - Add a fixup for Packard-Bell desktop with ALC880
ASoC: wm_adsp: Release firmware on error
ASoC: wm_adsp: Use GFP_DMA for things that may be DMAed
ASoC: arizona: Use actual rather than desired BCLK when calculating LRCLK
ASoC: wm2200: correct mixer values and text
ASoC: MAINTAINERS: Update email address.
ASoC: wm5110: Correct AEC loopback mask
ASoC: wm5102: Correct AEC loopback mask
ASoC: dapm: Fix sense of regulator bypass mode
ASoC: fsl: fix multiple definition of init_module
ASoC: arizona: Disable free-running mode on FLL1
