We will be registering and unregistering the soc_camera_platform platform
device multiple times, therefore we need a .release() method and have to
nullify the kobj.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Add a struct device pointer to struct soc_camera_platform_info and let the user
(ap325rxa) pass it down to soc_camera_platform.c in its .add_device() method.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
soc_camera_platform.c is only used by y SuperH ap325rxa board. This patch
converts soc_camera_platform.c and its users for the soc-camera platform-
device conversion and also extends soc-camera core to handle non-I2C cameras.
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Switch to using both register sets - side A and side B for display panning.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch prevents the USB1 interrupt from remaining asserted
immediately after re-boot or during a jump in to a secondary kernel.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This board doesn't use trapped I/O for anything, so just kill off the
select. This was causing problems in the unhandled page fault die path.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the kfr2r09 board code so it compiles if CONFIG_I2C=n.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port CN26 on the Solution Engine 7724
board. The r8a66597-udc driver is hooked up as a platform device
and some registers are configured to enable the USB in gadget mode.
The hardware driving the USB port is the on-chip USB1 block in
the sh7724 processor configured as USB gadget controller.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add USB gadget support for port YC301 on the KFR2R09 board.
The r8a66597-udc driver is hooked up as a platform device,
clocks are enabled via I2C and some registers are configured
to enable the USB in gadget mode. The hardware driving the
USB port is the on-chip USB0 block in the sh7724 processor
configured as USB gadget controller.
This board is using external hardware to detect USB hotplug
events and allows the processor to dynamically start and stop
clocks. This well thought out hardware feature is unused at
this point and plug and play is unfortunately unsupported.
To properly support all hardware features the USB gadget
stack may need some adjustment.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds preliminary support for the EcoVec board.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch simply adds LCDC hwblk_id data for the kfr2r09 board.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the Solution Engine 7724 board code to use
in-SoC KEYSC resources for the keyboard platform device. Using
the in-SoC key scan controller fixes a crash-during-resume issue.
Without this patch the KEYSC hardware block located in the board
specific FPGA is used together with an external IRQ which is
routed through the FPGA and handled by some board specific demux
code. This board specific FPGA interrupt code does not implement
desc->set_wake() so the enable_irq_wake() call in the sh_keysc
driver will fail at suspend-to-ram time and the disable_irq_wake()
will bomb out when resuming.
Changing the platform data to use the in-SoC KEYSC hardware makes
the se7724 board support code less special which is a good thing.
Also, the board specific KEYSC pin setup code selects in-SoC pin
functions already which makes the current FPGA platform device data
look like a typo.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the AP325RXA board code to register devices at
arch_initcall() time instead of device_initcall(). This
fix unbreaks pcf8563 RTC driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert the Migo-R board code to register devices at
arch_initcall() time instead of __initcall(). This fix
unbreaks migor_ts touch screen driver support.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for LED9, LED10 and LED11 on
the Solution Engine 7724 board. If CONFIG_PM is enabled
then these LEDs are used to show the hardware sleep
mode used by the processor. Useful to debug cpuidle.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the NAND flash chip
attached to CS4 on the KFR2R09 board. The device is
driven by the platform device driver "onenand-flash".
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the WQVGA LCD display used by
the KFR2R09 board. The LCD module is a TX07D34VM0AAA made
by Hitachi, and this module is made up by a R61517 chip
together with a 240x400 pixel display. The screen is
attached to the SuperH Mobile LCDC using a 18-bit SYS bus.
The register settings used by the SYS panel setup code are
based on an out-of-tree driver which apart from duplicating
all LCDC driver code and writing to non-existing hardware
registers also never was posted for upstream merge.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7724 board specific
on-chip sh7724 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to kfr2r09 board specific on-chip sh7724
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to AP325RXA board specific on-chip sh7723
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Solution Engine 7722 board specific
on-chip sh7722 platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add hwblk_id to Migo-R board specific on-chip sh7722
platform devices.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was no big meaning in the support of SVGA,
but 720p support is necessary for ms7724se board.
So, this patch support 720p instead of SVGA.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds KEYSC keypad support to the kfr2r09 board.
The keys driven by the sh7724 on-chip KEYSC block are
described as a platform device and platform data for
the sh_keysc driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds NOR flash support to the kfr2r09 board.
NOR flash support is added by describing the NOR flash
chip hooked up to CS0 as platform device data for the
physmap-flash MTD driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds basic kfr2r09 board support. Only
the SCIF1 console is supported with this patch, but
this patch and a proper sh7724 configuration is all
that is needed. Combine with an initramfs to have a
small RAM based kernel and distribution booted as
zImage from RAM via JTAG.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
