There is quite some confusion around the bit-ordering in DSD samples,
and no general agreement that defines whether hardware is supposed to
expect the oldest sample in the MSB or the LSB of a byte.
ALSA will hence set the rule that on the software API layer, bytes
always carry the oldest bit in the most significant bit of a byte, and
the driver has to translate that at runtime in order to match the
hardware layout.
This patch adds support for this by adding a boolean flag to the
audio format struct.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In order to provide a compatibility way for pushing DSD
samples through ordinary PCM channels, the "DoP open Standard" was
invented. See http://www.dsd-guide.com for the official document.
The host is required to stuff DSD marker bytes (0x05, 0xfa,
alternating) in the MSB of 24 bit wide samples on the bus, in addition
to the 16 bits of actual DSD sample payload.
To support this, the hardware and software stride logic in the driver
has to be tweaked a bit, as we make the userspace believe we're
operating on 16 bit samples, while we in fact push one more byte per
channel down to the hardware.
The DOP runtime information is stored in struct snd_usb_substream, so
we can keep track of our state across multiple calls to
prepare_playback_urb_dsd_dop().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For normal PCM transfer, this change has no effect, as the endpoint's
stride is always frame_bits/8. For DSD DOP streams, however, which is
added later, the hardware stride differs from the software stride, and
the endpoint has the correct information in these cases.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds two formats for Direct Stream Digital (DSD), a
pulse-density encoding format which is described here:
https://en.wikipedia.org/wiki/Direct_Stream_Digital
DSD operates on 2.8, 5.6 or 11.2MHz sample rates and as a 1-bit
stream.
The two new types added by this patch describe streams that are capable
of handling DSD samples in DOP format as 8-bit or in 16-bit (or at a x8
or x16 data rate, respectively).
DSD itself specifies samples in *bit*, while DOP and ALSA handle them
as *bytes*. Hence, a factor of 8 or 16 has to be applied for the sample
rare configuration, according to the following table:
configured hardware
176.4KHz 352.8kHz 705.6KHz <---- sample rate
8-bit 2.8MHz 5.6MHz
16-bit 2.8Mhz 5.6MHz 11.2MHz
`-----------------------------'
actual DSD sample rates
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When pin default configs are overridden via patch option, these are
evaluated before fixups are applied. Since some fixups change the
whole codec trees and/or add pins dynamically, this sanity check might
not pass when pins aren't present at the time the function is called.
We may reorder the execution, but an easier fix is simply to disable
this sanity check.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix to return a negative error code from the error handling
case instead of 0, as returned elsewhere in this function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The flag bus->shutdown implies that the control elements might have
been already destroyed. When a codec is resumed at this state and
tries to call vmaster hook (e.g. in snd_hda_gen_init()), it would
refer to a non-existing object, resulting in Oops in the end.
This patch just adds a check of the flag in the caller side for
avoiding such a crash.
Though, the best would be to clear hook->sw_kctl by the destructor of
the corresponding ctl element, but vmaster uses its own private_free,
it can't be done easily. So let it be for a while.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The hardware revision of the codec is based at 0x40. Subtract that
before convering to ASCII. The same as it is done for 98095.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
This patch adds a playback and capture streams to the dummy codec DAI
configuration. Most permissive set of sampling rates and formats is used.
This patch is needed for playback and capturing on a codec-less systems,
as otherwise the PCM device nodes are not even created.
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows us to access the DAI DMA data when we create the PCM. We'll use
this when converting imx to generic DMA engine PCM driver.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Unfortunately there are still quite a few platforms with a dmaengine driver
which do not support reporting the number of bytes left to transfer. If we want
to support these platforms in the generic dmaengine PCM driver we have.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the generic dmaengine PCM driver instead of a custom implementation.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for platforms which don't use devicetree yet or have to optionally
support a non-devicetree way to request the DMA channel. The patch adds the
compat_request_channel and compat_filter_fn callbacks to the
snd_dmaengine_pcm_config struct. If the compat_request_channel is implemented it
will be used to request the DMA channel. If not dma_request_channel with
compat_filter_fn as the filter function will be used to request the channel.
The patch also exports the snd_dmaengine_pcm_request_chan() function, since
compat platforms will want to use it to request their DMA channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a generic dmaengine PCM driver. It builds on top of the
dmaengine PCM library and adds the missing pieces like DMA channel management,
buffer management and channel configuration. It will be able to replace the
majority of the existing platform specific dmaengine based PCM drivers.
Devicetree is used to map the DMA channels to the PCM device.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
snd_soc_{add,remove}_platform are similar to snd_soc_register_platform and
snd_soc_unregister_platform with the difference that they won't allocate and
free the snd_soc_platform structure.
Also add snd_soc_lookup_platform which looks up a platform by the device it has
been registered for.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Refactor the dmaengine PCM library to allow the DMA channel to be requested
before opening a PCM substream. snd_dmaengine_pcm_open() now expects a DMA
channel instead of a filter function and filter parameter as its parameters.
snd_dmaengine_pcm_close() is updated to not release the DMA channel. This allows
a dmaengine based PCM driver to request its channels before the substream is
opened.
The patch also introduces two new functions, snd_dmaengine_pcm_open_request_chan()
and snd_dmaengine_pcm_close_release_chan(), which have the same signature and
behaviour of the old snd_dmaengine_pcm_{open,close}() and internally use the new
variants of these functions. All users of snd_dmaengine_pcm_{open,close}() are
updated to use snd_dmaengine_pcm_open_request_chan() and
snd_dmaengine_pcm_close_release_chan().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When graphics initializes the HDMI chip, sometimes this leads to
pins going into D3 and right channel being muted. If the audio driver
finishes initialization before the graphic driver does, this situation
becomes permanent.
This is a workaround that checks for this situation and corrects it on
playback prepare. It has been verified working on at least one machine.
BugLink: https://bugs.launchpad.net/bugs/1167270
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When setting up the aamix output paths, use the primary DAC instead of
the individual DAC for each output as default. Otherwise multiple
DACs will be turned on for a single aamix widget, which results in
doubly or more volumes, because the duplicated signals will be sent
through all these DACs for a single stream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add definitions for AC97 control register.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Acked-by: Timur Tabi <timur@tabi.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we have a loopback mixer control, this should manage the state
whether the output paths include the aamix or not. But the current
code blindly initializes the output paths with aamix = true, thus the
aamix is enabled unless the loopback mixer control is changed.
Also, update_aamix_paths() called by the loopback mixer control put
callback invokes snd_hda_activate_path() with aamix = true even for
disabling the mixing. This leaves the aamix path even though the
loopback control is turned off.
This patch fixes these issues:
- Introduced aamix_default() helper to indicate whether with_aamix is
true or false as default
- Fix the argument in update_aamix_paths() for disabling loopback
Reported-by: Lydia Wang <LydiaWang@viatech.com.cn>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For capture, the delay through the codec contributes to the time stamp
of the sample recorded at the A to D. Rename the codec time stamp
function appropriately.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJRa//sAAoJELSic+t+oim95J8P/A0ia+ergNHjM7VuV89XyDxJ
qT+hciD2F7HGiGqCluyIxWTWY4NCG8JUMVj4j+qDltc+DZA7DGX654gUXOlyYIFb
Otbt7s8CNGIGRuUkRAzoSCewL2B/veFjOdnw6XW2w9YcYHeYbjl9BOlXOdCJtPRb
yroKHl6mzD99eD8y26QVjk7z3bJGmdBkckilYz+Fws+NACGZqu5KpzF11+DnrAL+
0Bl3F/fafDEUwFqDvWaQD2728aXxJL1pg0aR8mueRCcGBPnk3qWycj9kQZqVFBpV
i8Q+xNEnIVECfDKclT0j0bAL+2ftcg2Jm2lryupMtopGxR3Uii1kgGKSMwYHz82E
bvQ8y3phLc6u5VtIIJj0iPE7ZE5H/2///KgFEj6z/P2tZPWobMkURb+9bGQTJ8Qv
pUYGiOV0S/+59WAv0qnN4XpomA69EPPu5AuiPd30T+iNna998OjFEBRmIc/wJ519
QYlhj1ThWsa3Uoi1V0hmhAPHCXVtOKHnZfj95cyaD4Vq8zdqUmptJI+UvUJFgRUm
30eVVNwcIb0XE+0K4skMbVbpCkRA4m+pBGE7+Z+x72kYTfmg6uVET1T/sGgDFIAG
XCZ8QOXXYxpmpXMDqTKO30oBHdN6V0tClkSCuQ6H2PoICi0VYX3ZZWT8/Qno3JuN
bBxyWhz3gYL/MII6qJpE
=lx37
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.10' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v3.10
A bunch of changes here, the most interesting one subsystem wise being
Morimoto-san's work to create snd_soc_component which doesn't do much
for now but will be pretty important going forwards:
- Add a new component object type which will form the basis of moving
to a more generic handling of SoC and off-SoC components, contributed
by Kuninori Morimoto.
- A fairly large set of cleanups for the dmaengine integration from
Lars-Peter Clausen, starting to move towards being able to have a
generic driver based on the library.
- Performance optimisations to DAPM from Ryo Tsutsui.
- Support for mixer control sharing in DAPM from Stephen Warren.
- Multiplatform ARM cleanups from Arnd Bergmann.
- New CODEC drivers for AK5385 and TAS5086 from Daniel Mack.
Commit 88a8516a21 (ALSA: usbaudio: implement USB autosuspend)
introduced autopm for all USB audio/MIDI devices. However, many MIDI
devices, such as synthesizers, do not merely transmit MIDI messages but
use their MIDI inputs to control other functions. With autopm, these
devices would get powered down as soon as the last MIDI port device is
closed on the host.
Even some plain MIDI interfaces could get broken: they automatically
send Active Sensing messages while powered up, but as soon as these
messages cease, the receiving device would interpret this as an
accidental disconnection.
Commit f5f165418c (ALSA: usb-audio: Fix missing autopm for MIDI input)
introduced another regression: some devices (e.g. the Roland GAIA SH-01)
are self-powered but do a reset whenever the USB interface's power state
changes.
To work around all this, just disable autopm for all USB MIDI devices.
Reported-by: Laurens Holst
Cc: <stable@vger.kernel.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With this patch, a TRRS headset mic cannot be successfully detected
on the Asus X101CH, and we can also distinguish between headphone
and headset automatically.
Buglink: https://bugs.launchpad.net/bugs/1169138
Co-authored-by: Kailang <kailang@realtek.com>
Tested-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On some machines, there is a headset jack that can support both
headphone, headsets (of both CTIA and OMTP type) and mic-in.
On other machines, the headset jack supports headphone, headsets
(both CTIA and OMTP), but not mic-in.
This patch implements that functionality as different capture sources.
Buglink: https://bugs.launchpad.net/bugs/1169143
Tested-by: David Chen <david.chen@canonical.com>
Co-authored-by: Kailang <kailang@realtek.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When recording at 176.2KHz or 192Khz, the device adds a 32-bit length
header to the capture packets, which obviously needs to be ignored for
recording to work properly.
Userspace expected: L0 L1 L2 R0 R1 R2
...but actually got: R2 L0 L1 L2 R0 R1
Also, the last byte of the length header being interpreted as L0 of
the first sample caused spikes every 0.5ms, resulting in a loud 16KHz
tone (about the highest 'B' on a piano) being present throughout
captures.
Tested at all sample rates on an E-Mu 0404USB, and tested for
regressions on a generic USB headset.
Signed-off-by: Calvin Owens <jcalvinowens@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit b2ca78717c (ARM: S3C24XX: make gta02.h local) already replaced
the GTA02_GPIO_* constants in neo1973-wm8753.c but forgot to remove the
inclusion of mach/gta02.h before moving the file out of mach/.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A few updates, more than I'd like, fixing some relatively small issues
but mostly driver specific ones. Nothing wildly exciting so if it
doesn't make v3.9 it won't be the end of the world but it'd be nice.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=W1XN
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.9-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Updates for v3.9
A few updates, more than I'd like, fixing some relatively small issues
but mostly driver specific ones. Nothing wildly exciting so if it
doesn't make v3.9 it won't be the end of the world but it'd be nice.
The plat/regs-iis.h and plat/regs-ac97.h files in the samsung platform
are only needed by the ASoC drivers, so they can be moved into the same
directory, as one more step towards a multiplatform build.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Firmwares may provide some firmware wide configuration regions which can
be configured by the coefficient files using the firmware ID as the
algorithm ID, include these in the algorithm list.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The idma_reg_addr_init function is used by the samsung i2s driver,
which can be a loadable module, so we have to export this function.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The second argument to the module_device_table macro must be the
name of the device id array. In the samsung i2s driver, there
was a small typo, resulting in a build error when building it
as a loadable module.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
With multiplatform kernels, we cannot use hardwired IRQ
numbers in device drivers. This changes the idma driver
to use a proper resource, like all other drivers do.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have a flag for headphone mics, we can use that flag
in the jack creation instead of creating the jack manually.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
I never liked that we move our speaker and hp pins to line out
if there are not any line outs; but now that we do,
add some convenience functions to find hp and speaker pins even
if they have been moved.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This allows a specific mic to get the "Headphone Mic" name, in addition
to the existing "Headset Mic" name.
Also, it allows for a special mark: if the sequence number is set
to 0xc, that's an indication to prefer it for headset mic, and if it's
set to 0xd, that's an indication to prefer it for headphone mic.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It turns out the devices from Playback Design need the delay quirk
after usb_set_interface from clocks.c as well. Make it a proper
quirks function and factor out the code to quirks.c.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The only part of proc_dir_entry the code outside of fs/proc
really cares about is PDE(inode)->data. Provide a helper
for that; static inline for now, eventually will be moved
to fs/proc, along with the knowledge of struct proc_dir_entry
layout.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
The Charge Pump needs the DSP clock to work properly, without it the
bypass to HP/LINEOUT is not working properly. This requirement is not
mentioned in the datasheet but has been confirmed by Mark Brown from
Wolfson.
Signed-off-by: Alban Bedel <alban.bedel@avionic-design.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
There's already a device revision stored in the core data structure,
don't duplicate it in the CODEC driver.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For playback add the codec-side delay to the timestamp, for capture
subtract it. This brings the timestamps in line with the time that
was recently added to the delay reporting.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A test for CONFIG_SND_SOC_UX500_AB5500 was added in v3.5. But there
never was a corresponding Kconfig symbol so this test has always
evaluated to true. And since AB5500 support was removed in v3.5 it
appears safe to remove this test and a few lines of code.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This removes <mach/hardware.h> and <mach/db8500-regs.h>
from the Ux500, merging them into the local include
"db8500-regs.h" in mach-ux500. There is some impact
outside the ux500 machine, but most of it is dealt with
in earlier patches.
Contains portions of a clean-up patch from Arnd Bergmann.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This header file only contains platform data structure definitions,
so it's straightforward to move.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Delete one include rather than move it]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The snd_pcm_hardware structs for playback and capture in the ux500 PCM are
identical, so remove one of them and use the same snd_pcm_hardware struct for
both playback and capture. Also move the defines used to initialize the
snd_pcm_hardware fields from ux500_pcm.h to ux500_pcm.c since that's the only
place where they are used.
Also drop the assignment of the snd_pcm_hardware struct to runtime->hw since
that is what the call to snd_soc_set_runtime_hwparams() right above it already
does, so the second assignment is redundant.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The usb_control_msg() function expects __u16 types and performs
the endianness conversions by itself.
However, in three places, a conversion is performed before it is
handed over to usb_control_msg(), which leads to a double conversion
(= no conversion):
* snd_usb_nativeinstruments_boot_quirk()
* snd_nativeinstruments_control_get()
* snd_nativeinstruments_control_put()
Caught by sparse:
sound/usb/mixer_quirks.c:512:38: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:512:38: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:512:38: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:35: warning: incorrect type in argument 5 (different base types)
sound/usb/mixer_quirks.c:543:35: expected unsigned short [unsigned] [usertype] value
sound/usb/mixer_quirks.c:543:35: got restricted __le16 [usertype] <noident>
sound/usb/mixer_quirks.c:543:56: warning: incorrect type in argument 6 (different base types)
sound/usb/mixer_quirks.c:543:56: expected unsigned short [unsigned] [usertype] index
sound/usb/mixer_quirks.c:543:56: got restricted __le16 [usertype] <noident>
sound/usb/quirks.c:502:35: warning: incorrect type in argument 5 (different base types)
sound/usb/quirks.c:502:35: expected unsigned short [unsigned] [usertype] value
sound/usb/quirks.c:502:35: got restricted __le16 [usertype] <noident>
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct pin configs for the Acer AC700. Most importantly indicate
that SPDIF is connected, it routes to HDMI out.
Similar to Aspire models, chain in the DMIC fixup and allow it to be
applied to this codec (ALC269VB) as well.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Channel size settings will be made at the end of
davinci_mcasp_hw_params() routine and thus overwrite frame
format settings made for DIT mode. This patch fixes this issue
by taking op_mode into account. Tested with official PSP 3.2
kernel and sii9022a HDMI transmitter.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
AFSX won't be used in DIT mode. The related pins are AHCLKX and
the data pins.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Acked-by: Vaibhav Bedia <vaibhav.bedia@ti.com>
Tested-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit 453807f3 ("ASoC: ep93xx: Use ep93xx_dma_params instead of
ep93xx_pcm_dma_params") introduced a small compile error by not updating the
name of the 'dma_port' field to 'port'. This patch fixes it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the common DAI DMA data struct for fsl/imx, this allows us to use the common
helper function to configure the DMA slave config based on the DAI DMA data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The DSP in the CA0132 codec adds a variable latency to audio depending
on what processing is being done. Add a new patch op to return that
latency for capture and playback streams. The latency is determined
by which blocks are enabled and knowing how much latency is added by
each block.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a new codec PCM ops, get_delay(), to obtain the codec/stream-
specific PCM delay count. When it's NULL, nothing changes.
This new feature was requested for CA0132, which has significant
delays in the path depending on the running DSP code.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
changed is not initialized in path_power_down_sync, but it is expected
to be false in case no change happened in the loop. So set it to
false.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This reverts commit 6ab317419c.
The commit [6ab317419c: ALSA: hda - Allow power_save_controller option
override DCAPS] changed the behavior of power_save_controller so that
it can override the driver capability. This assumed that this option
is rarely changed dynamically unlike power_save option. Too naive.
It turned out that the user-space power-management tool tries to set
power_save_controller option to 1 together with power_save option
without knowing what's actually doing. This enabled forcibly the
runtime PM of the controller, which is known to be broken om many
chips thus disabled as default.
So, the only sane fix is to revert this commit again. It was intended
to ease debugging/testing for runtime PM enablement, but obviously we
need another way for it.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=56171
Reported-and-tested-by: Nikita Tsukanov <keks9n@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Rename "Digitial In" to "Digital In". This function is only used for
proc output, so should not cause any problems to change.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* Added the device ID to the modalias list and assinged ALC662 patches
for it
* Added 4 port support for the device ID 0671 in alc662_parse_auto_config
Signed-off-by: Rainer Koenig <Rainer.Koenig@ts.fujitsu.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some clocks might be read-only, e.g., external clocks (see also
UAC2 4.7.2.1).
In this case, setting the sample frequency will always fail
(even if the rate is equal to the current clock rate),
therefore do not write, but read the value and compare to the
requested rate.
If the clock is read only, avoid reading it twice.
If it doesn't match, return -ENXIO since the clock is invalid for
this configuration.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Show the error code returned from the USB subsystem in
the debug messages.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a module param to disable auto clock selection.
This is provided for users that expect the audio stream to
fail when the clock source is invalid (e.g., the word clock
was unintentionally disconnected).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If a selector is available on a device, it may be pointing to a
clock source which is currently invalid.
If there is a valid clock source which can be selected, switch
to it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move the check that parse_audio_format_rates_v2() do after
receiving the clock source entity ID directly into the find
function and add a validation flag to the function.
This patch does not introduce any logic flow change.
It is provided to allow introducing automatic clock switching
easier later. By moving this uac_clock_source_is_valid callsite,
2 additional callsites can be avoided.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace the endianness conversions with the kernel-wide swabbing macros
in get/set_sample_rate_v2.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct spelling of snd_usb_endpoint_implict_feedback_sink in all
occurances.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Minor style fix, following a general code style in the kernel.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Merge branch 'fix/samsung' of
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into
asoc-component to resolve trivial conflict
Conflicts:
sound/soc/samsung/i2s.c
Use the common DAI DMA data struct for tegra, this allows us to use the common
helper function to configure the DMA slave config based on the DAI DMA data.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the common DAI DMA data struct for omap, this allows us to use the common
helper function to configure the DMA slave config based on the DAI DMA data.
For omap-dmic and omap-mcpdm also move the DMA data from a global variable to
the driver state struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds a common DMA data struct which can be used by DAI drivers to
communicate their DMA configuration requirements to the DMA pcm driver. Having
a common data structure for this allows us to implement common functions on top
of them, which can be used by multiple platforms.
This patch also introduces a new function to initialize certain fields of a
dma_slave_config struct from the common DAI DMA data struct.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Usually device_fc should be set to false for audio DMAs. Initialize it in a
common place so drivers don't have to do this manually.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The tegra dmaengine driver does not support pausing and resuming a DMA stream.
The tegra PCM driver still claims to support pause and resume though and
implements them by stopping and restarting the stream. This is not what an
application using pause/resume would expect. Usually applications have support
for working around PCMs which do not support suspend and resume, so don't set
the SNDRV_PCM_INFO_PAUSE and SNDRV_PCM_INFO_RESUME flags for the tegra PCM and
use the default snd_dmaengine_pcm_trigger callback.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just for cleaning up, introduce a new function get_sample_rate_v2()
for replacing two identical calls in set_sample_rate_v2().
No functional change.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently, a new platform device is created for secondary device
by calling platform_device_register_resndata and then the drvdata
is set for this device.
The following patch has been added to driver core:
"driver core: fix possible missing of device probe".
This results in the added device getting probed immediately but
the drvdata for the secondary device is not yet set.
This patch removes the platform_device_register_resndata call and
instead calls platform_device_alloc, platform_set_drvdata and
platform_device_add which fixes the above issue.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch fixes a possible crash in case drvdata for the secondary
device is not set.
Signed-off-by: Prathyush K <prathyush.k@samsung.com>
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The C-Media CM6631 USB receiver doesn't respond to changes in sample rate
while the interface is active. The same behavior is observed in other UAC2
hardware like the VIA VT1731.
Reset the interface after setting the sampling frequency on sample rate
changes, to ensure that the sample rate set by snd_usb_init_sample_rate() is
used. Otherwise, the device will try to use the sample rate of the previous
stream, causing distorted sound on sample rate changes.
The reset is performed for all UAC2 devices, as it should not affect a
standards compliant device, but it is only necessary for C-Media CM6631,
VIA VT1731 and possibly others.
Failure to read sample rate from the device is not handled as an error in
set_sample_rate_v2(), as (permanent or intermittent) failure to read sample
rate isn't essential for a successful sample rate set.
Signed-off-by: Torstein Hegge <hegge@resisty.net>
Acked-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch let ELD debug message show 'pin_eld->monitor_present' which reflects
the real pin response to verb GET_PIN_SENSE.
'eld->monitor_present' should not be used here because 'eld' is a temp
structure now and so its "monitor_present" is not set.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
In function snd_hdmi_get_eld(), the variable 'ret' should be initialized to 0.
Otherwise it will be returned uninitialized as non-zero after ELD info is got
successfully. Thus hdmi_present_sense() will always assume ELD info is invalid
by mistake, and /proc file system cannot show the proper ELD info.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Cc: stable@vger.kernel.org
Acked-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Turing on the headphone amp interferes with the impedance measurement
used to detect a TRRS style headset microphone. Delay the HP turn on
until 500ms after the jack is detected, allowing the mic detection
state machine to run to completion.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Used kmemdup instead of replicating it's behaviour with kmalloc followed
by memcpy.
Patch found using coccinelle.
Signed-off-by: Alexandru Gheorghiu <gheorghiuandru@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The Kconfig symbol SND_SOC_OF_SIMPLE got removed in commit
f0fba2ad1b ("ASoC: multi-component - ASoC
Multi-Component Support"). But that commit missed one instance. Remove
it now, together with the prompt it has effectively hidden ever since.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When clearing the walked flags there is no need to clear all paths, we
only need to clear the paths we actually walked. This means we can split
dapm_clear_walk() into input and output versions and rather than going
through all DAPM paths we can recurse down the path until we encounter
paths we have not yet walked.
This reduces the number of operations we need to perform and improves
cache locality.
[Pulled out of the vendor tree that the patch was originally generated
for by me, any bugs were introduced in that process -- broonie]
Signed-off-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We already clear the walked state in dapm_widget_power_check(), no need
to do it again.
Signed-off-by: Ryo Tsutsui <Ryo.Tsutsui@wolfsonmicro.com>
Acked-by: Liam Girdwood <liam.r.girdwood@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJRWLTrAAoJEHm+PkMAQRiGe8oH/iMy48mecVWvxVZn74Tx3Cef
xmW/PnAIj28EhSPqK49N/Ow6AfQToFKf7AP0ge20KAf5teTq95AY+tH74DAANt8F
BjKXXTZiR5xwBvRkq7CR5wDcCvEcBAAz8fgTEd6SEDB2d2VXFf5eKdKUqt1avTCh
Z6Hup5kuwX+ddtwY2DCBXtp2n6fL0Rm5yLzY1A3OOBye1E7VyLTF7M5BR603Q44P
4kRLxn8+R7jy3hTuZIhAeoS8TKUoBwVk7DmKxEzrhTHZVOmvwE9lEHybRnIyOpd/
k1JnbRbiPsLsCVFOn10SQkGDAIk00lro3tuWP2C1ljERiD/OOh5Ui9nXYAhMkbI=
=q15K
-----END PGP SIGNATURE-----
Merge tag 'v3.9-rc5' into patchwork
Linux 3.9-rc5
* tag 'v3.9-rc5': (1080 commits)
Linux 3.9-rc5
Revert "lockdep: check that no locks held at freeze time"
dw_dmac: adjust slave_id accordingly to request line base
dmaengine: dw_dma: fix endianess for DT xlate function
PNP: List Rafael Wysocki as a maintainer
rbd: don't zero-fill non-image object requests
ia64 idle: delete stale (*idle)() function pointer
Btrfs: don't drop path when printing out tree errors in scrub
target: Fix RESERVATION_CONFLICT status regression for iscsi-target special case
tcm_vhost: Avoid VIRTIO_RING_F_EVENT_IDX feature bit
Revert "mm: introduce VM_POPULATE flag to better deal with racy userspace programs"
usb: ftdi_sio: Add support for Mitsubishi FX-USB-AW/-BD
mg_disk: fix error return code in mg_probe()
Btrfs: fix wrong return value of btrfs_lookup_csum()
Btrfs: fix wrong reservation of csums
Btrfs: fix double free in the btrfs_qgroup_account_ref()
Btrfs: limit the global reserve to 512mb
Btrfs: hold the ordered operations mutex when waiting on ordered extents
Btrfs: fix space accounting for unlink and rename
Btrfs: fix space leak when we fail to reserve metadata space
...
The header <mach/hardware.h> is not needed at all, and <mach/mxs.h> is
needed only for macros MXS_SET_ADDR and MXS_CLR_ADDR. Define the macros
and remove the mach header inclusions.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This is the equivalent of commit af46800 "ASoC: Implement mux control
sharing", but applied to mixers instead of muxes.
This allows a single control to affect multiple mixer widgets at once,
which is useful when there is a single set of register bits that affects
multiple mixers in HW, for example both the L and R mixers of a stereo
path.
Without this, you either:
1) End up with multiple controls that affect the same register bits, but
whose DAPM state falls out of sync with HW, since the DAPM state is only
updated for the specific control that is modified, and not for other
paths that are affected by the register bit(s).
2) False paths through DAPM, since you end up merging unconnected stereo
paths together into a single widget which hosts the single control, and
then branching back out again, thus conjoining the enable states of the
two input paths.
Now that the kcontrol creation logic is split out into a separate
function, dapm_create_or_share_mixmux_kcontrol(), also use that to
replace most of the body of dapm_new_mux(). This should produce no
functional change, but simply eliminates some mostly duplicated code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
while at it, update the copyright timeline too
Signed-off-by: Jeeja KP <jeeja.kp@intel.com>
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that we have regular register mapped controls we should be splitting
the control sets for ADSP1 and ADSP2 as the register maps are not
identical. Do that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When a new stream is being opened it is necessary to cancel any delayed
power down of the audio.
[Fixed unused variable -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The ASoC core does no not modify the driver of a platform. Making it const
allows ASoC platform drivers to declare the snd_soc_platform_driver struct as
const.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Without this, modules will fail to link against those symbols.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
siu_dai.c is using snd_soc_register_dais(),
even though array size of siu_i2s_dai is 1.
OTOH, new API snd_soc_register_component() uses properly
snd_soc_register_dai() (henceforth dai()) or
snd_soc_register_dais() (henceforth dais()) via num_dai.
Then, cpu_dai_name will be "siu-i2s-dai" if dais() was used,
and it will be "siu-pcm-audio" if dai() was used.
Therefore this patch fixup migor_dai :: cpu_dai_name too.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
All drivers are using snd_soc_register_component()
instead of snd_soc_register_dai[s]()
snd_soc_[un]register_dai[s]() are no longer needed
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
