* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: ad714x - read the interrupt status registers in a row
Input: ad714x - use DMA-safe buffers for spi_write()
Input: ad714x - fix endianness issues
Input: ad714xx-spi - force SPI bus into the default 8-bit mode
Input: ep93xx_keypad - add missing include of linux/module.h
Input: tnetv107x-ts - add missing include of linux/module.h
Input: max11801_ts - correct license statement
Input: atmel_mxt_ts - report pressure information from the driver
Input: bcm5974 - Add support for newer MacBookPro8,2
Input: wacom - report id 3 returns 4 bytes of data
Input: wacom - add WAC_MSG_RETRIES define
Input: wacom - add support for the Wacom Bamboo Pen (CTL-660/K)
Input: tegra-kbc - correct call to input_free_device
Input: mpu3050 - correct call to input_free_device
Input: bcm5974 - add support for touchpads found in MacBookAir4,2
Input: mma8450 - fix module device table type
Input: remove CLOCK_TICK_RATE from analog joystick driver
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse:
fuse: check size of FUSE_NOTIFY_INVAL_ENTRY message
fuse: mark pages accessed when written to
fuse: delete dead .write_begin and .write_end aops
fuse: fix flock
fuse: fix non-ANSI void function notation
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (29 commits)
bridge: fix a possible net_device leak
net: Documentation: RFC 2553bis is now RFC 3493
atm: br2684: Fix oops due to skb->dev being NULL
ipv6: Fix ipv6_getsockopt for IPV6_2292PKTOPTIONS
net: netdev-features.txt update to Documentation/networking/00-INDEX
vlan: reset headers on accel emulation path
forcedeth: call vlan_mode only if hw supports vlans
via-velocity: remove non-tagged packet filtering
bonding:reset backup and inactive flag of slave
net_sched: fix port mirror/redirect stats reporting
sit tunnels: propagate IPv6 transport class to IPv4 Type of Service
gianfar: reduce stack usage in gianfar_ethtool.c
net: minor update to Documentation/networking/scaling.txt
net: add missing entries to Documentation/networking/00-INDEX
gianfar: prevent buggy hw rx vlan tagging
net: sh_eth: Fix build by forgot including linux/interrupt.h
drivers/net/can/sja1000/plx_pci.c: eliminate double free
usbnet/cdc_ncm: Don't use stack variables for DMA
vmxnet3: Don't enable vlan filters in promiscuous mode.
iwlagn: sysfs couldn't find the priv pointer
...
Make sure that only assigned storage increments are unassigned when
attaching a storage element.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The main purpose for PSW restart will be kdump. Therefore customers will
issue "system restart" for creating a dump. If kdump is not enabled,
currently "PSW restart" will reboot the system and then no dump can
be created any more. In order to still allow a manual stand-alone dump in
the case a user issues "PSW restart" on a system that has not enabled
kdump we now stop the system.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
reipl_fcp_kset was just initialized, so it appears that it should be tested
instead of reipl_kset.
Signed-off-by: Julia Lawall <julia@diku.dk>
Reported-by: Suman Saha <sumsaha@gmail.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Data is only used to temporarily hold information to be copied to the user
level, so it should be freed before leaving the function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@exists@
local idexpression x;
statement S,S1;
expression E;
identifier fl;
expression *ptr != NULL;
@@
x = \(kmalloc\|kzalloc\|kcalloc\)(...);
...
if (x == NULL) S
<... when != x
when != if (...) { <+...kfree(x)...+> }
when any
when != true x == NULL
x->fl
...>
(
if (x == NULL) S1
|
if (...) { ... when != x
when forall
(
return \(0\|<+...x...+>\|ptr\);
|
* return ...;
)
}
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
When IPL'ing from a block device and an NSS should be created we must
make sure that the kernel image and the initrd are in different 1MB
segments. Otherwise creating the NSS will fail.
So we make sure the initrd is 4MB behind the end of the kernel image
like we do already when IPL via the VM reader is performed.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
This was a typo in clockdev declaration for at91sam9261 SoC.
Fix the kernel hanging when switching clocksource to TC (tcb_clksrc).
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Remy Bohmer <linux@bohmer.net>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Board file support for Ventana is not yet mainlined, and probably won't
ever be given the move to Device-Tree. Consequently, the Ventana entry
is being removed from arch/arm/tools/mach-types in the next merge window,
since it was registered over a year ago.
This will also remove function machine_is_ventana(), which is used by
the ASoC Tegra WM8903 machine driver. This will cause compilation
failures. Drop Ventana support to resolve this.
Hopefully, in the not-too-distant future, tegra_wm8903.c will be able to
configure itself from Device-Tree, and hence we'll be able to re-instate
Ventana support just by creating a .dts file for the board.
Also note that Aebl support is in a similar boat. However, that board
isn't scheduled for deprecation for at least another 5 months, and
perhaps we will have completely removed non-Device-Tree support from
tegra_wm8903.c by then and/or adjusted mach-types policy.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Joseph Pentland <jp@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It seems that an entry for the SP805 watchdog in the table of clocks was
missing. This results in the sp805_wdt driver rejecting the device with
the following errors:
sp805-wdt mb:wdt: Clock not found
sp805-wdt mb:wdt: Probe Failed!!!
sp805-wdt: probe of mb:wdt failed with error -2
While not obviously stated in the hardware docs, the onboard SP810's
"REFCLK" is connected to a 32.768KHz crystal, and this drives the
watchdog. Add a struct clk and corresponding lookup entry for it.
Signed-off-by: Nick Bowler <nbowler@elliptictech.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
FUSE_NOTIFY_INVAL_ENTRY didn't check the length of the write so the
message processing could overrun and result in a "kernel BUG at
fs/fuse/dev.c:629!"
Reported-by: Han-Wen Nienhuys <hanwenn@gmail.com>
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
CC: stable@kernel.org
Function i5k_channel_pci_id looks like it can fail, while a better
code design would make it more obvious that it can't. We can even get
rid of the function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Darrick J. Wong <djwong@us.ibm.com>
Signed-off-by: Guenter Roeck <guenter.roeck@ericsson.com>
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86-32, vdso: On system call restart after SYSENTER, use int $0x80
x86, UV: Remove UV delay in starting slave cpus
x86, olpc: Wait for last byte of EC command to be accepted
When we enter a 32-bit system call via SYSENTER or SYSCALL, we shuffle
the arguments to match the int $0x80 calling convention. This was
probably a design mistake, but it's what it is now. This causes
errors if the system call as to be restarted.
For SYSENTER, we have to invoke the instruction from the vdso as the
return address is hardcoded. Accordingly, we can simply replace the
jump in the vdso with an int $0x80 instruction and use the slower
entry point for a post-restart.
Suggested-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Link: http://lkml.kernel.org/r/CA%2B55aFztZ=r5wa0x26KJQxvZOaQq8s2v3u50wCyJcA-Sc4g8gQ@mail.gmail.com
Cc: <stable@kernel.org>
I looks like something used to implicitly include linux/interrupt.h,
and no longer does. Fix the resulting build error by explicitly
including it.
Signed-off-by: David Daney <david.daney@cavium.com>
Cc: David S. Miller <davem@davemloft.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"ret" needs to be signed for the error handling to work properly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
zcache_put_page() was modified to pass page_address(page) instead of the
actual page structure. In combination with the function signature changes
to tmem_put() and zcache_pampd_create(), zcache_pampd_create() tries to
(re)derive the page structure from the virtual address. However, if the
original page is a high memory page (or any unmapped page), this
virt_to_page() fails because the page_address() in zcache_put_page()
returned NULL.
This patch changes zcache_put_page() and zcache_get_page() to pass
the page structure instead of the page's virtual address, which
may or may not exist.
Signed-off-by: Seth Jennings <sjenning@linux.vnet.ibm.com>
Acked-by: Dan Magenheimer <dan.magenheimer@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fixes fallout due to the removal of the cast in commit aa462abe8a
("mm: fix __page_to_pfn for a const struct page argument")
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: linux-m68k@lists.linux-m68k.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Due to missing memset function declaration.
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since the arrival of kernel version 3.0 in the staging tree it
turns out compile error occurs for sparc64, powerpc, and arm
platforms. This patch fixes that issue.
Reviewed-by: Pieter-Paul Giesberts <pieterpg@broadcom.com>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
After commit 5a865ba, we require a separate value to indicate the
number of supported SSIDs in scheduled scans. This patch adds a
proper value to the wl12xx driver.
This fixes a regression in 3.1-rc3 where scheduled scans were not
working properly with the wl12xx driver.
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl1271_sdio_power_on checks if the return value of pm_runtime_get_sync
is non-zero, and if so bails out.
However, pm_runtime_get_sync can return a positive number which does not
suggest an error has occurred. This is problematic for two reasons:
1. The function will needlessly bail out without decrementing back the
runtime PM reference counter.
2. wl1271_power_on only checks if wl1271_power_on return value is
negative. This means that wl1271_power_on will continue even if
wl1271_sdio_power_on bailed out. As a result, sdio transactions will
be initiated without properly enabling the sdio function and claiming
the host. This could even lead to a kernel panic.
Fix this by only checking that the return value of pm_runtime_get_sync
is non-negative.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The testmode NVS push command is no longer in use. In addition, it has
several implementation issues that prevent it from working correctly:
1. wl1271_tm_cmd_configure relies on wl->chip.id being set. However,
since the device was not necessarily booted by the time the function
is called, wl->chip.id will be initialized to 0.
2. The NVS file is fetched by calling request_firmware() before it is
possible to push an NVS file.
3. The maximum allowed size of nl binary payloads is not sufficient for
pushing NVS files.
4. Pushing 128x NVS files will always fail due to a bug in the
validation code.
5. In case the pushed NVS file is found invalid, the mutex will be kept
locked and the nvs member will become a dangling pointer.
Since this feature is not being used, remove it completely instead of
fixing it.
Signed-off-by: Ido Yariv <ido@wizery.com>
Acked-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit adf6e07922.
Remove system PM methods which can race with runtime PM methods.
Also, as of v3.1, the PM domain level code for OMAP handles device
power state transistions automatically for devices, so drivers no
longer need to specifically call the bus/pm_domain methods themselves.
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
If there is a signal pending and wait_for_completion_interruptible_timeout
exited because of the -ERESTARTSYS error we are unable to send any more
i2c messages.
So, deprecate this _interruptible_ variant call.
Signed-off-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
* 'for-linus' of git://oss.sgi.com/xfs/xfs:
xfs: fix tracing builds inside the source tree
xfs: remove subdirectories
xfs: don't expect xfs headers to be in subdirectories
Fixes logic bug that software flow control cannot be disabled, because
serial_omap_configure_xonxoff() is not called if both IXON and IXOFF bits
are cleared.
Signed-off-by: Nick Pelly <npelly@google.com>
Acked-by: Govindraj.R <govindraj.raja@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon: Extended DDC Probing for Toshiba L300D Radeon Mobility X1100 HDMI-A Connector
drm/ttm: ensure ttm for new node is bound before calling move_notify()
drm/ttm: unbind ttm before destroying node in accel move cleanup
drm/ttm: fix ttm_bo_add_ttm(user) failure path
drm/radeon: Make vramlimit parameter actually work.
drm/radeon: Explicitly print GTT/VRAM offsets on test failure.
drm/radeon: Take IH ring into account for test size calculation.
drm/radeon/alpha: Add Alpha support to Radeon DRM code
This reverts commit f3637a5f2e.
It turns out that this breaks several drivers, one example being OMAP
boards which use the on-board OMAP UARTs and the omap-serial driver that
will not boot to userspace after the commit.
Paul Walmsley reports that enabling CONFIG_DEBUG_SHIRQ reveals 'IRQ
handler type mismatch' errors:
IRQ handler type mismatch for IRQ 74
current handler: serial idle
...
and the reason is that setting IRQF_ONESHOT will now result in those
interrupt handlers having different IRQF flags, and thus being
unsharable. So the commit log in the reverted commit:
"Since it is required for those users and
there is no difference for others it makes sense to add this flag
unconditionally."
is simply not true: there may not be any difference from a "actions at
irq time", but there is a *big* difference wrt this flag testing irq
management (see __setup_irq() in kernel/irq/manage.c).
One solution may be to stop verifying IRQF_ONESHOT in __setup_irq(), but
right now the safe course of action is to revert the change. Let's
revisit this in a later merge window.
Reported-by: Paul Walmsley <paul@pwsan.com>
Cc: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Requested-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When a user has SYS_ADMIN capabilities and uart->ops->startup returns
an error in uart_startup, we silently drop the error. We then return 0
and behave as if it didn't fail. (Not quite, since we set TTY_IO_ERROR
bit and leave ASYNC_INITIALIZED bit cleared.)
This all is to allow setserial to work with improperly configured or
unconfigured ports. User can thus set port properties and reconfigure
properly.
This patch only documents this behavior.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Russel King <linux@arm.linux.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tty_operations->remove is normally called like:
queue_release_one_tty
->tty_shutdown
->tty_driver_remove_tty
->tty_operations->remove
However tty_shutdown() is called from queue_release_one_tty() only if
tty_operations->shutdown is NULL. But for pty, it is not.
pty_unix98_shutdown() is used there as ->shutdown.
So tty_operations->remove of pty (i.e. pty_unix98_remove()) is never
called. This results in invalid pty_count. I.e. what can be seen in
/proc/sys/kernel/pty/nr.
I see this was already reported at:
https://lkml.org/lkml/2009/11/5/370
But it was not fixed since then.
This patch is kind of a hackish way. The problem lies in ->install. We
allocate there another tty (so-called tty->link). So ->install is
called once, but ->remove twice, for both tty and tty->link. The fix
here is to count both tty and tty->link and divide the count by 2 for
user.
And to have ->remove called, let's make tty_driver_remove_tty() global
and call that from pty_unix98_shutdown() (tty_operations->shutdown).
While at it, let's document that when ->shutdown is defined,
tty_shutdown() is not called.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Alan Cox <alan@linux.intel.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is to fix an issue where output will suddenly become very slow.
The problem occurs on 8250 UARTS with the hardware bug UART_BUG_THRE.
BACKGROUND
For normal UARTs (without UART_BUG_THRE): When the serial core layer
gets new transmit data and the transmitter is idle, it buffers the
data and calls the 8250s' serial8250_start_tx() routine which will
simply enable the TX interrupt in the IER register and return. This
should immediately fire a THRE interrupt and begin transmitting the
data.
For buggy UARTs (with UART_BUG_THRE): merely enabling the TX interrupt
in IER does not necessarily generate a new THRE interrupt.
Therefore, a background timer periodically checks to see if there is
pending data, and starts transmission if that is the case.
The bug happens on SMP systems when the system has nothing to transmit,
the transmit interrupt is disabled and the following sequence occurs:
- CPU0: The background timer routine serial8250_backup_timeout()
starts and saves the state of the interrupt enable register (IER)
and then disables all interrupts in IER. NOTE: The transmit interrupt
(TI) bit is saved as disabled.
- CPU1: The serial core gets data to transmit, grabs the port lock and
calls serial8250_start_tx() which enables the TI in IER.
- CPU0: serial8250_backup_timeout() waits for the port lock.
- CPU1: finishes (with TI enabled) and releases the port lock.
- CPU0: serial8250_backup_timeout() calls the interrupt routine which
will transmit the next fifo's worth of data and then restores the
IER from the previously saved value (TI disabled).
At this point, as long as the serial core has more transmit data
buffered, it will not call serial8250_start_tx() again and the
background timer routine will slowly transmit the data.
The fix is to have serial8250_start_tx() get the port lock before
it saves the IER state and release it after restoring IER. This will
prevent serial8250_start_tx() from running in parallel.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds support for the Rosewill RC-305 four-port PCI serial
card, and probably any other four-port serial cards based on the
Moschip MCS9865 chip, assuming that the EEPROM on the card was
programmed in accordance with Table 6 of the MCS9865 EEPROM
Application Note version 0.3 dated 16-May-2008, available from the
Moschip web site (registration required).
This patch is based on an earlier patch [1] for the SYBA 6x serial
port card by Ira W. Snyder.
[1]: http://www.gossamer-threads.com/lists/linux/kernel/1162435
Signed-off-by: Eric Smith <eric@brouhaha.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since commit e0626e38 (spi: prefix modalias with "spi:"),
the spi modalias is prefixed with "spi:".
This patch adds "spi:" prefix and removes "-spi" suffix in the modalias.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When multiple headphones or speakers are assigned but no individual
DACs are available, the driver should take the first HP/SPK DAC instead
of another primary output. The patch adds a bit-flag to dac field of
struct pin_dac_pair indicating that it's a slave DAC.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Toshiba Satellite L300D with ATI Mobility Radeon X1100 sends data
to i2c bus for a HDMI connector that is not implemented/existent
on the notebook's board.
Fix by applying extented DDC probing for this connector.
Requires [PATCH] drm/radeon: Extended DDC Probing for Connectors
with Improperly Wired DDC Lines
Tested for kernel 2.6.38 on Toshiba Satellite L300D notebook
BugLink: http://bugs.launchpad.net/bugs/826677
Signed-off-by: Thomas Reim <reimth@gmail.com>
Acked-by: Chris Routh <routhy@gmail.com>
Cc: <stable@kernel.org>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The internal states, jack_present and line_jack_present should be
updated upon unsolicited events even if no automute is set.
Otherwise the wrong state is referred when the automute behavior is
changed by the mixer control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the headphone or speaker output has no own DAC, initialize the path
using the primary DAC. Otherwise the path won't be set properly and
can result in the silence.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The wiimote resets the current drm when an extension is plugged in.
Fortunately, it also sends a status report in this situation so we just
reset the drm on every status report to keep the drm consistent.
Also handle return reports from the wiimote which indicate success and
failure of requests that we've sent.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The wiimote reports data in several data reporting modes (DRM). The DRM
request makes the wiimote send data in the requested drm.
The DRM mode can be set explicitely or can be chosen by the driver. To let
the driver choose the DRM mode, pass WIIPROTO_REQ_NULL placeholder to it. This
is no valid request and is replaced with an appropriate DRM.
Currently, the driver always sets the basic DRM_K mode, but this will be
extended when further peripherals like accelerometer and IR are supported.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This registers 4 led devices to allow controlling the wiimote leds via standard
LED sysfs API. It removes the four sysfs attributes so we don't have two APIs
for one device.
Signed-off-by: David Herrmann <dh.herrmann@googlemail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
