Serial devices send both pen and touch data through the same logical
port. Since we scaled touch to pen maximum, we use pen resolution
for touch as well here.
This is under the assumption that pen and touch share the same physical
surface. In the case when a small physical dimensional difference occurs
between pen and touch, we assume the tolerance for touch point precision
is higher than pen and the difference is within touch point tolerance.
A per-MT tool based resolution mechanism should be introduced if the
above assumption does not hold true for the pen and touch devices any
more.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some machines, like Dell Studio XPS 16 (1640), touchpad fails to
respond to the standard query after first reset but may start
responding later, so let's repeat reset sequence several (3) times.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
synaptics_set_advanced_gesture_mode() affect capabilities bits we should
perform comparison after calling this function, otherwise they will never
match and we will be forced to perform full reconnect.
Signed-off-by: Alexandre Peixoto Ferreira <alexandref75@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Also remove fake ABS_RX/ABS_RY "axes" that were used to report physical
dimensions now that we have better way.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Reviewed-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Currently sysrq_enabled and __sysrq_enabled are initialised separately
and inconsistently, leading to sysrq being actually enabled by reported
as not enabled in sysfs. The first change to the sysfs configurable
synchronises these two:
static int __read_mostly sysrq_enabled = 1;
static int __sysrq_enabled;
Add a common define to carry the default for these preventing them becoming
out of sync again. Default this to 1 to mirror previous behaviour.
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Cc: stable@kernel.org
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We were forgetting to set up device capabilities for KEY_VSW entries.
Reported-by: Tapio Vihuri <tapio.vihuri@nokia.com>
Tested-by: Tapio Vihuri <tapio.vihuri@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds support for the internal matrix keyboard controller for
Nvidia Tegra platforms.
Signed-off-by: Rakesh Iyer <riyer@nvidia.com>
Reviewed-by: Trilok Soni <tsoni@codeaurora.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The driver does not require hardirq context and can work with threaded
interrupts as well, so let's switch to request_any_context_irq which
will select the context that is available for us.
Signed-off-by: Philippe Langlais <philippe.langlais@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Parse and pass the status byte information to the registered serio
drivers as well as the data bytes.
Signed-off-by: David Engraf<david.engraf@sysgo.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
If request_irq() fails we should return the proper error instead of -1.
Signed-off-by: Davidlohr Bueso <dave@gnu.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove duplicate display resolution parameters from platform data as
one pair is quite enough.
Signed-off-by: Naveen Kumar Gaddipati <naveen.gaddipati@stericsson.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should use IS_ERR() when checking whether clk_get() succeeded or
not since it returns errors by encoding error codes with ERR_PTR().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We should use IS_ERR() when checking whether clk_get() succeeded or
not since it returns errors by encoding error codes with ERR_PTR().
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This switch is used to signal that user want to disable screen
transitions from portrait to landscape mode and back.
Signed-off-by: Jekyll Lai <jekyll_lai@wistron.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
'features' is a bit array, not byte array
Signed-off-by: Alexander Stein <alexander.stein@informatik.tu-chemnitz.de>
Acked-by: Anssi Hannula <anssi.hannula@iki.fi>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Emulate single-touch compatible events for the 2-finger panels
so that they can be used with single-touch legacy clients.
Assign device ids as Wacom USB vendor ID and product ID.
Name the device to reflect its specific features.
Scale touch coordinates to pen maximum if pen supported.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This is driver for EasyPoint AS5011 2 axis joystick chip. This chip is
plugged on an I2C bus.
Tested on ARM processor (i.MX27).
Signed-off-by: Fabien Marteau <fabien.marteau@armadeus.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The only platform using this driver (mach-aaec2000) is no longer in
the kernel so remove the driver.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
i8042 controller present in Dell Vostro V13 errorneously signals spurious
timeouts.
Introduce i8042.notimeout parameter for ignoring i8042-signalled timeouts
and apply this quirk automatically for Dell Vostro V13, based on DMI match.
In addition to that, this machine also needs to be added to nomux blacklist.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the cy8ctmg110_ts driver over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the migor_ts driver over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the mcs5000_ts driver over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the eeti_ts driver over.
Compile tested only by me, but Sven Neumann reports that the new code
works.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Sven Neumann <s.neumann@raumfeld.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There is a general move towards the use of dev_pm_ops rather than
bus specific suspend APIs as this simplifies both the bus and PM core
implementations. Convert the ad7879-ts I2C support over.
Compile tested only.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Not all penabled devices support touch. The same holds true for touch
devices, so we should be setting up devices according to the results
returned when we query the hardware.
Signed-off-by: Ping Cheng <pingc@wacom.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds notebook Acer Aspire 5100 to the list of Dritek HW. Acer
Aspire 5100 needs Dritek keyboard extension to support all Fn keys.
Signed-off-by: Pali Rohár <pali.rohar@gmail.com>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OLPC has switched to a Synaptics touchpad. It turns out that it's
pretty useless in absolute mode. This patch looks for an OLPC
system (via DMI tables), and refuses to init Synaptics mode in
that scenario (falling back to relative mode).
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Minor comment fixup for typos and grammar. Noticed while adding a
separate workaround.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In multitouch mode, at least one device (fw: 7.4 id: 0x1c0b1) sometimes
sends a final main packet with x == 1. Since the normal values are above
1472, this is clearly bogus. At the same time, a two-finger touch is
signaled, even though only one finger was on the pad to begin with. This
patch ignores the packet altogether, removing the problem.
Acked-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The Synaptics 2.7 series of touchpads support a mode for reporting two
sets of X/Y/Pressure data (advanced gesture mode). By default, these
devices report only single finger data, depriving userspace of the
nowadays ubiquitous two-finger scroll gesture.
Enabling advanced gesture mode also enables the multi-finger report,
although the device does not claim that capability. Up to three
fingers can be reported this way.
While two or three fingers are touching, the normal packet is
prepended by a reduced finger packet of lower resolution. From the two
packets (which do not represent the actual fingers), the bounding
rectangle of the individual contacts can be extracted. This
information is sufficient to perform scaling gestures and a limited
form of rotation gesture. The behavior has been coined semi-mt
capability, and is signaled to userspace via the INPUT_PROP_SEMI_MT
device property.
Work to decode the advanced gesture packet: Takashi Iwai.
Cleanup and testing of the original patch: Chase Douglas.
Minor cleanup and testing: Chris Bagwell.
Finalization and semi-mt support: Henrik Rydberg.
Reported-by: Tobyn Bertram
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Chris Bagwell <chris@cnpbagwell.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
With the new input property interface, it is possible to report the
special quirks of a device using ioctl/sysfs. This patch sets up the
device as a pointer, and reports the clickpad functionality via the
INPUT_PROP_BUTTONPAD property.
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Looking at the uevent stream for input devices, all properties are on
the form "A=B" except the bitmap values, which are on the form
"A==B". This bug has been around at least since 2007, and the input
uevent code has been untouched since. The recent addition of device
properties suggests this is a good time for a remedy.
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Today, userspace sets up an input device based on the data it emits.
This is not always enough; a tablet and a touchscreen may emit exactly
the same data, for instance, but the former should be set up with a
pointer whereas the latter does not need to. Recently, a new type of
touchpad has emerged where the buttons are under the pad, which
changes logic without changing the emitted data. This patch introduces
a new ioctl, EVIOCGPROP, which enables user access to a set of device
properties useful during setup. The properties are given as a bitmap
in the same fashion as the event types, and are also made available
via sysfs, uevent and /proc/bus/input/devices.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
This patch adds support for another Wetab device (726b), and grabs it
accordingly in hid-core.
[rydberg@euromail.se: rename and log message changes]
Signed-off-by: Andy Ross <andy@plausible.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The input multitouch core is now located in its own file,
and maintained via a git tree. Update the maintainers entry
accordingly.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
The Samsung NB30 touch has a DWAV dual-touch device. This patch adds
the NB30 to the list of supported devices, and grabs it accordingly in
hid-core.
[rydberg@euromail.se: rename and log message changes]
Signed-off-by: Richard Nauber <Richard.Nauber@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Add the new supported devices to the kernel menu config help text.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephane Chatty <chatty@enac.fr>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
