viafb: unify modesetting functions
This patch unifies some cleaned up modesetting functions to prepare for
moving them to an extra file. This includes make them use via_io and
changing there names to reflect that they do not depend on anything
framebuffer specific.
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
The camera engine captures to framebuffer memory, so we need to set some
aside for that purpose. There is no proper memory allocator for fbmem;
instead, accel.c just trims some space off the top. Alas, without creating
that proper memory allocator, the only way to make this work is to hack it
into the same bit of code in accel.c. The allocation must happen *after*
the others (some code, including user-space XV stuff, makes assumptions on
where the cursor space is), and before the rest of the framebuffer is set
up.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This code provides a minimal amount of access to the DMA engine as
needed by the camera driver. VX855 only; it's guaranteed not to work
on other chipsets, so it won't try.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The viafb device shares a single interrupt control register among several
distinct subunits. This adds a simple layer for management of that
register.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The code was ugly and didn't check whether i2c operations were succeeding;
make it a little better.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The camera driver will need this to look up a specific adapter.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
If an adapter has been configured for GPIO (or off), we should not try to
use it as an I2C port.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Another step toward making this thing a real multifunction device driver.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch puts redesigned versions of the basic io functions that
are used overall the driver in an extra header. It is prefixed with
via_ as no framebuffer dependend stuff is in there. They were inlined
as they are really simple which reduced the module size about 2.5%.
The parameter order of read and write was fixed as it really doesn't
make sense to change the order as they are parts of the same address
and not source and destination.
Wrapper which use the new functions were added to hw.h to replicate
the old interface and avoid changing all old code.
[jc: added one comment]
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
This is a simple gpiolib driver giving access to the GPIO lines in the
VIA framebuffer system. A simple mechanism exists for switching lines
between GPIO and I2C, but it's only compile-time for now.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch moves data of interest into a new viafb_dev structure which
describes the device as a whole; the idea here is to create a separation
between what all devices may need and what the framebuffer device in
particular needs.
I've also made some small steps toward thinning out the global.h mess.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
The first step toward turning viafb into a multifunction driver. This
patch creates a new via-core.c file which serves as the main PCI driver;
everything else comes below that. Some work has been done to rationalize
the i2c drivers in this new scheme.
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Cc: Harald Welte <laforge@gnumonks.org>
Acked-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
...otherwise it seems we run into conflicts with shadowy other users which
don't expect to see i2c taking control of ports it never used to do
anything with.
Reported-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch changes the way how the various I2C busses are used internally
inside the viafb driver: Previosuly, only a single i2c_adapter was created,
even though two different hardware I2C busses are accessed: A structure member
in a global variable was modified to indicate the bus to be used.
Now, all existing hardware busses are registered with the i2c core, and the
viafb_i2c_{read,write}byte[s]() function take the adapter number as function
call parameter, rather than referring to the global structure member.
[jc: even more painful merge with mainline changes ->2.6.34]
[jc: painful merge with OLPC changes]
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch is a painful merge of change
a90bab567ece3e915d0ccd55ab00c9bb333fa8c0 (viafb: Add support for 2D
accelerated framebuffer on VX800/VX855) in the OLPC tree, originally by
Harald Welte. Harald's changelog read:
The VX800/VX820 and the VX855/VX875 chipsets have a different 2D
acceleration engine called "M1". The M1 engine has some subtle
(and some not-so-subtle) differences to the previous engines, so
support for accelerated framebuffer on those chipsets was disabled
so far.
This merge tries to preserve Harald's changes in the framework of the
much-changed 2.6.34 viafb code.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This will help us for the upcoming support for 2D acceleration using
the M1 engine.
[jc: fixed merge conflicts]
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
As suggested by Florian: make both mode-setting paths use the same code.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Commit c3e2567384 (viafb: 2D engine rewrite)
changed the setting of the GEMODE register so that the reserved bits are no
longer preserved. Fix that; at the same time, move this code to its own
function and restore the use of symbolic constants.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This was part of Harald's "make viafb a first-class citizen using
pci_driver" patch, but somehow got dropped when that patch went into
mainline.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
This patch alters viafb to use the proper Linux in-kernel API to access
PCI configuration space, rather than poking at I/O ports by itself.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
The current code executed from module_init() in viafb does not have
proper error checking and [partial] resoure release paths in case
an error happens half way through driver initialization.
This patch adresses the most obvious of those issues, such as a
leftover i2c bus if module_init (and thus module load) fails.
[jc: fixed merge conflicts]
[jc: also restored -ENOMEM return on ioremap() fail]
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: ScottFang@viatech.com.cn
Cc: JosephChan@via.com.tw
Signed-off-by: Harald Welte <HaraldWelte@viatech.com>
Add a MAINTAINERS record for the key management facility.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/joern/logfs:
[LogFS] Erase new journal segments
[LogFS] Move reserved segments with journal
[LogFS] Clear PagePrivate when moving journal
Simplify and fix pad_wbuf
Prevent data corruption in logfs_rewrite_block()
Use deactivate_locked_super
Fix logfs_get_sb_final error path
Write out both superblocks on mismatch
Prevent schedule while atomic in __logfs_readdir
Plug memory leak in writeseg_end_io
Limit max_pages for insane devices
Open segment file before using it
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Do not free zero sized per cpu areas
x86: Make sure free_init_pages() frees pages on page boundary
x86: Make smp_locks end with page alignment
Fix a memory leak on an OOM condition in prepare_usermodehelper_creds().
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Fix a race in o2dlm lockres mastery
Ocfs2: Handle deletion of reflinked oprhan inodes correctly.
Ocfs2: Journaling i_flags and i_orphaned_slot when adding inode to orphan dir.
ocfs2: Clear undo bits when local alloc is freed
ocfs2: Init meta_ac properly in ocfs2_create_empty_xattr_block.
ocfs2: Fix the update of name_offset when removing xattrs
ocfs2: Always try for maximum bits with new local alloc windows
ocfs2: set i_mode on disk during acl operations
ocfs2: Update i_blocks in reflink operations.
ocfs2: Change bg_chain check for ocfs2_validate_gd_parent.
[PATCH] Skip check for mandatory locks when unlocking
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (33 commits)
r8169: offical fix for CVE-2009-4537 (overlength frame DMAs)
ipv6: Don't drop cache route entry unless timer actually expired.
tulip: Add missing parens.
r8169: fix broken register writes
pcnet_cs: add new id
bonding: fix broken multicast with round-robin mode
drivers/net: Fix continuation lines
e1000: do not modify tx_queue_len on link speed change
net: ipmr/ip6mr: prevent out-of-bounds vif_table access
ixgbe: Do not run all Diagnostic offline tests when VFs are active
igb: use correct bits to identify if managability is enabled
benet: Fix compile warnnings in drivers/net/benet/be_ethtool.c
net: Add MSG_WAITFORONE flag to recvmmsg
e1000e: do not modify tx_queue_len on link speed change
igbvf: do not modify tx_queue_len on link speed change
ipv4: Restart rt_intern_hash after emergency rebuild (v2)
ipv4: Cleanup struct net dereference in rt_intern_hash
net: fix netlink address dumping in IPv4/IPv6
tulip: Fix null dereference in uli526x_rx_packet()
gianfar: fix undo of reserve()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Properly truncate pt_regs framepointer in perf callback.
arch/sparc/kernel: Use set_cpus_allowed_ptr
sparc: Fix use of uid16_t and gid16_t in asm/stat.h
In commit 9df93939b7 ("ext3: Use bitops to read/modify
EXT3_I(inode)->i_state") ext3 changed its internal 'i_state' variable to
use bitops for its state handling. However, unline the same ext4
change, it didn't actually change the name of the field when it changed
the semantics of it.
As a result, an old use of 'i_state' remained in fs/ext3/ialloc.c that
initialized the field to EXT3_STATE_NEW. And that does not work
_at_all_ when we're now working with individually named bits rather than
values that get masked. So the code tried to mark the state to be new,
but in actual fact set the field to EXT3_STATE_JDATA. Which makes no
sense at all, and screws up all the code that checks whether the inode
was newly allocated.
In particular, it made the xattr code unhappy, and caused various random
behavior, like apparently
https://bugzilla.redhat.com/show_bug.cgi?id=577911
So fix the initialization, and rename the field to match ext4 so that we
don't have this happen again.
Cc: James Morris <jmorris@namei.org>
Cc: Stephen Smalley <sds@tycho.nsa.gov>
Cc: Daniel J Walsh <dwalsh@redhat.com>
Cc: Eric Paris <eparis@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Official patch to fix the r8169 frame length check error.
Based on this initial thread:
http://marc.info/?l=linux-netdev&m=126202972828626&w=1
This is the official patch to fix the frame length problems in the r8169
driver. As noted in the previous thread, while this patch incurs a performance
hit on the driver, its possible to improve performance dynamically by updating
the mtu and rx_copybreak values at runtime to return performance to what it was
for those NICS which are unaffected by the ideosyncracy (if there are any).
Summary:
A while back Eric submitted a patch for r8169 in which the proper
allocated frame size was written to RXMaxSize to prevent the NIC from dmaing too
much data. This was done in commit fdd7b4c330. A
long time prior to that however, Francois posted
126fa4b9ca, which expiclitly disabled the MaxSize
setting due to the fact that the hardware behaved in odd ways when overlong
frames were received on NIC's supported by this driver. This was mentioned in a
security conference recently:
http://events.ccc.de/congress/2009/Fahrplan//events/3596.en.html
It seems that if we can't enable frame size filtering, then, as Eric correctly
noticed, we can find ourselves DMA-ing too much data to a buffer, causing
corruption. As a result is seems that we are forced to allocate a frame which
is ready to handle a maximally sized receive.
This obviously has performance issues with it, so to mitigate that issue, this
patch does two things:
1) Raises the copybreak value to the frame allocation size, which should force
appropriately sized packets to get allocated on rx, rather than a full new 16k
buffer.
2) This patch only disables frame filtering initially (i.e., during the NIC
open), changing the MTU results in ring buffer allocation of a size in relation
to the new mtu (along with a warning indicating that this is dangerous).
Because of item (2), individuals who can't cope with the performance hit (or can
otherwise filter frames to prevent the bug), or who have hardware they are sure
is unaffected by this issue, can manually lower the copybreak and reset the mtu
such that performance is restored easily.
Signed-off-by: Neil Horman <nhorman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For 32-bit processes, we save the full 64-bits of the regs in pt_regs.
But unlike when the userspace actually does load and store
instructions, the top 32-bits don't get automatically truncated by the
cpu in kernel mode (because the kernel doesn't execute with PSTATE_AM
address masking enabled).
So we have to do it by hand.
Reported-by: Frederic Weisbecker <fweisbec@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Intel X58 have asc7621a chip. So added X58 entry in Kconfig for asc7621.
Also arranged existing models in ascending order.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
"ret" is used to store the return value for watchdog_trigger() and it
should be signed for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add missing newline to dev_warn() message string. This is more of an issue
with older kernels that don't automatically add a newline if it was missing
from the end of the previous line.
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Avoid hex and decimal confusion when printing out the cpu model.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
If the device contains on old logfs image and the journal is moved to
segment that have never been used by the current logfs and not all
journal segments are erased before the next mount, the old content can
confuse mount code. To prevent this, always erase the new journal
segments.
Signed-off-by: Joern Engel <joern@logfs.org>
This avoids an infinite loop in free_early_partial().
Add a warning to free_early_partial() to catch future problems.
-v5: put back start > end back into WARN_ONCE()
-v6: use one line for warning, suggested by Linus
-v7: more tests
-v8: remove the function name as suggested by Johannes
WARN_ONCE() will print out that function name.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Tested-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Tested-by: Joel Becker <joel.becker@oracle.com>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1269830604-26214-4-git-send-email-yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When CONFIG_NO_BOOTMEM=y, it could use memory more effiently, or
in a more compact fashion.
Example:
Allocated new RAMDISK: 00ec2000 - 0248ce57
Move RAMDISK from 000000002ea04000 - 000000002ffcee56 to 00ec2000 - 0248ce56
The new RAMDISK's end is not page aligned.
Last page could be shared with other users.
When free_init_pages are called for initrd or .init, the page
could be freed and we could corrupt other data.
code segment in free_init_pages():
| for (; addr < end; addr += PAGE_SIZE) {
| ClearPageReserved(virt_to_page(addr));
| init_page_count(virt_to_page(addr));
| memset((void *)(addr & ~(PAGE_SIZE-1)),
| POISON_FREE_INITMEM, PAGE_SIZE);
| free_page(addr);
| totalram_pages++;
| }
last half page could be used as one whole free page.
So page align the boundaries.
-v2: make the original initramdisk to be aligned, according to
Johannes, otherwise we have the chance to lose one page.
we still need to keep initrd_end not aligned, otherwise it could
confuse decompressor.
-v3: change to WARN_ON instead, suggested by Johannes.
-v4: use PAGE_ALIGN, suggested by Johannes.
We may fix that macro name later to PAGE_ALIGN_UP, and PAGE_ALIGN_DOWN
Add comments about assuming ramdisk start is aligned
in relocate_initrd(), change to re get ramdisk_image instead of save it
to make diff smaller. Add warning for wrong range, suggested by Johannes.
-v6: remove one WARN()
We need to align beginning in free_init_pages()
do not copy more than ramdisk_size, noticed by Johannes
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Tested-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: David Miller <davem@davemloft.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1269830604-26214-3-git-send-email-yinghai@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
New documentation should have an entry in the 00-INDEX. Correct git
urls.
Signed-off-by: Cheng Renquan <crquan@gmail.com>
Signed-off-by: Sage Weil <sage@newdream.net>
