System suspends and hibernation are supposed to be as transparent as
possible. By this reasoning, if a USB device is already autosuspended
before the system sleep begins then it should remain autosuspended
after the system wakes up.
This patch (as1001) adds a skip_sys_resume flag to the usb_device
structure and uses it to avoid waking up devices which were suspended
when a system sleep began.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as999) fixes a problem that sometimes shows up when host
controller driver modules are loaded in the wrong order. If ehci-hcd
happens to initialize an EHCI controller while the companion OHCI or
UHCI controller is in the middle of a port reset, the reset can fail
and the companion may get very confused. The patch adds an
rw-semaphore and uses it to keep EHCI initialization and port resets
mutually exclusive.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: David Miller <davem@davemloft.net>
Cc: Dely L Sy <dely.l.sy@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
powertop currently tracks interrupts generated by uhci, ehci, and ohci,
but it has no way of telling which USB device to blame USB bus activity on.
This patch exports the number of URBs that are submitted for a given device.
Cat the file 'urbnum' in /sys/bus/usb/devices/.../
Signed-off-by: Sarah Sharp <sarah.a.sharp@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as995) cleans up the remains of the former NO_AUTOSUSPEND
quirk. Since autosuspend is disabled by default, we will let
userspace worry about which devices can safely be suspended. Thus the
lengthy series of quirk entries is no longer needed, and neither is
the quirk ID. I suppose someone might eventually run across a hub
that can't be suspended; let's ignore the possibility for now.
The patch also cleans up the hasty way in which autosuspend gets
disabled. Setting udev->autosuspend_delay to -1 wasn't quite right,
because the value is always supposed to be a multiple of HZ. It's
better to leave the delay value alone and set autosuspend_disabled,
which is what the quirk routine used to do.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as992) fixes a recently-added bug. During a FREEZE or
PRETHAW suspend notification, non-root devices don't actually get
suspended. So we shouldn't tell their parent hubs that they did.
(This code path used to be skipped over, until the FREEZE/PRETHAW test
got moved out of usb_suspend_both() into generic_suspend().)
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (jx001) fixes a variable assignment mistake in hub driver.
limited_power should be set to 0 if the hub is self-powered,and 1 if
the hub is bus-powered.
However, the effect of the code was exactly opposite to the spec's
statement for the Local Power Source field. The spec says, this field
is 1 meaning Local power supply lost while this field is 0 indicating
Local power supply good.(This statement is very confusing.)
So this patch switchs the 0 and 1.
Signed-off-by: Jason Xiao <jidong.xiao@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as989) makes usbcore flush all outstanding URBs for each
device as the device is suspended. This will be true even when
CONFIG_USB_SUSPEND is not enabled.
In addition, an extra can_submit flag is added to the usb_device
structure. That flag will be turned off whenever a suspend request
has been received for the device, even if the device isn't actually
suspended because CONFIG_USB_SUSPEND isn't set.
It's no longer necessary to check for the device state being equal to
USB_STATE_SUSPENDED during URB submission; that check can be replaced
by a check of the can_submit flag. This also permits us to remove
some questionable references to the deprecated power.power_state field.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as988) breaks usb_hcd_endpoint_disable() apart into two
routines. The first, usb_hcd_flush_endpoint() does the -ESHUTDOWN
unlinking of all URBs in the endpoint's queue and waits for them to
complete. The second, usb_hcd_disable_endpoint() -- renamed for
better grammatical style -- merely calls the HCD's endpoint_disable
method. The changeover is easy because the routine currently has only
one caller.
This separation of function will be exploited in the following patch:
When a device is suspended, the core will be able to cancel all
outstanding URBs for that device while leaving the HCD's
endpoint-related data structures intact for later.
As an added benefit, HCDs no longer need to check for existing URBs in
their endpoint_disable methods. It is now guaranteed that there will
be none.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as987) changes the way FREEZE and PRETHAW suspend events
are handled in usbcore. The decision about whether or not to ignore
them for non-root devices is pushed down into the USB-device driver,
instead of being made in the core code.
This is appropriate, since devices exported to a virtualized guest or
over a network may indeed need to handle these types of suspend, even
though normal devices don't.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as990) removes an annoying debugging message. Nobody
really cares when endpoint pseudo-devices are released.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as981) removes the remaining nontrivial usages of
urb->status from usbcore.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that urb->status isn't used, urb->lock doesn't protect anything.
This patch (as980) removes it and replaces it with a private mutex in
the one remaining place it was still used: usb_kill_urb.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator. Now the field
doesn't get set until just before the URB's completion routine is
called.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as978) reorganizes the way usbmon uses urb->status. It
now accepts the status value as an argument.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as971) fixes a small mistake: The URB's completion status
needs to be adjusted before the URB is passed to usmon_urb_complete(),
not afterward.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more. To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses. The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.
By moving the work out of the HCDs, this removes a fair amount of
repeated code.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as955) prevents the interface-related sysfs files and
endpoint pseudo-devices from being deleted and recreated when a call
to usb_set_interface() specifies the current altsetting. Since the
altsetting doesn't get changed, there's no need to do anything.
Furthermore, avoiding changes to the endpoint devices will be
necessary in the future. This code is called from usb_reset_device(),
which gets invoked for reset-resume processing, but upcoming changes
to the PM and driver cores will make it impossible to register devices
while a suspend/resume transition is in progress. Since we don't need
to re-register those endpoint devices anyhow, it's best to skip the
whole thing.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as954) implements a suggestion of David Brownell's. Now
the host controller drivers are responsible for linking and unlinking
URBs to/from their endpoint queues. This eliminates the possiblity of
strange situations where usbcore thinks an URB is linked but the HCD
thinks it isn't. It also means HCDs no longer have to check for URBs
being dequeued before they were fully enqueued.
In addition to the core changes, this requires changing every host
controller driver and the root-hub URB handler. For the most part the
required changes are fairly small; drivers have to call
usb_hcd_link_urb_to_ep() in their urb_enqueue method,
usb_hcd_check_unlink_urb() in their urb_dequeue method, and
usb_hcd_unlink_urb_from_ep() before giving URBs back. A few HCDs make
matters more complicated by the way they split up the flow of control.
In addition some method interfaces get changed. The endpoint argument
for urb_enqueue is now redundant so it is removed. The unlink status
is required by usb_hcd_check_unlink_urb(), so it has been added to
urb_dequeue.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As it is global, give it a usb specific name in the global namespace.
Cc: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Makes it possible to control the authorization of USB devices through
sysfs's /sys/usb/devices/*/authorize.
Update: per Adrian Bunk's suggestion, make dev_attr_authorized_default static
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
These USB API functions will do the full authorization/deauthorization
to be used for a device. When authorized we effectively allow a
configuration to be set. Reverse that when deauthorized.
Effectively this means that we have to clean all the configuration
descriptors on deauthorize and reload them when we authorized. We could
do without throwing them out for wired devices, but for wireless, we can
read them only after authenticating, and thus, when authorizing an
authenticated device we would need to read them. So to simplify, always
release them on deauthorize(), re-read them on authorize().
Also fix leak reported by Ragner Magalhaes; in usb_deauthorize_device(),
bNumConfigurations was being set to zero before the for loop, and thus
the different raw descriptors where never being freed.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch takes hub.c:usb_new_device() and splits it in three parts:
- The actual actions of adding a new device (quirk detection,
announcement and autoresume tracking)
- Actual discovery and probing of the configuration and interfaces
(split into __usb_configure_device())
- Configuration of the On-the-go parameters (split into
__usb_configure_device_otg()).
The fundamental reasons for doing this split are clarity (smaller
functions are easier to maintain) and to allow part of the code to be
reused when authorizing devices to connect.
When a device is authorized connection, we need to run through the
hoops we didn't run when it was connected but not authorized, which is
basically parsing the configurations and probing
them. usb_configure_device() will do that for us.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If called and the device is not authorized to be used, then we won't
choose a configuration (as they are not a concept that exists for an
unauthorized device). However, the device is added to the system.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If called and the device is not authorized to be used, it won't
configure the interface and print a message saying so.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If called and the device is not authorized to be used, then we don't
allow reading the configurations.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Will refuse to configure a non-authorized device.
Update: simplified if statement--thanks to Ragner Magalhaes for the
heads up.
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This path cleans the exit paths of usb_register_bus() [to use a goto
schema], maximum line length (keeping it under ~75).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This introduces /sys/bus/devices/usb*/authorized_default; it dictates
what is going to be the default authorization state for devices
connected to the host. User space can set that using the sysfs file.
We hook to the root hub instead of to the device controller as it is
quite easy to get to it in sysfs from the device structure (device
5-4.3 is usb5) vs. backtracking to the controller device.
By default it is set to be 'authorized' (!0) for normal, wired USB
devices and 'unauthorized' (0) for Wireless USB devices.
As suggested by Adrian Bunk, make authorized_default static
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as953) separates out three key portions from
usb_hcd_submit_urb(), usb_hcd_unlink_urb(), and usb_hcd_giveback_urb()
and puts them in separate functions of their own. In the next patch,
these functions will be called directly by host controller drivers
while holding their private spinlocks, which will remove the
possibility of some unpleasant races.
The code responsible for mapping and unmapping DMA buffers is also
placed into a couple of separate subroutines, for the sake of
cleanliness and consistency.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as952) adjusts the spinlock usage in the root-hub
emulation part of usbcore, to make it match more closely the pattern
used by regular host controller drivers. To wit: The private lock
(usb_hcd_root_hub_lock) is held throughout the important parts, and it
is dropped temporarily without re-enabling interrupts around the call
to usb_hcd_giveback_urb().
A nice side effect is that the code now avoids calling
local_irq_save(), thereby becoming more RT-friendly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as951) cleans up a few loose ends from earlier patches.
Redundant checks for non-NULL urb->dev are removed, as are checks of
urb->dev->bus (which can never be NULL). Conversely, a check for
non-NULL urb->ep is added to the unlink paths.
A homegrown round-down-to-power-of-2 loop is simplified by using the
ilog2 routine. The comparison in usb_urb_dir_in() is made more
transparent.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as948) removes most of the references to urb->pipe from
the usbfs routines in devio.c. The one tricky aspect is in
snoop_urb(), which can be called before the URB is submitted and which
uses usb_urb_dir_in(). For this to work properly, the URB's direction
flag must be set manually in proc_do_submiturb().
The patch also fixes a minor bug; the wValue, wIndex, and wLength
fields were snooped in proc_do_submiturb() without conversion from
le16 to CPU-byte-ordering.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as947) changes the device initialization and enumeration
code in hub.c; now udev->devnum will be set to 0 while the device is
being accessed at address 0. Until now this wasn't needed because the
address value was passed as part of urb->pipe; without that field the
device address must be stored elsewhere.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as946) eliminates many of the uses of urb->pipe in
usbcore. Unfortunately there will have to be a significant API
change, affecting all USB drivers, before we can remove it entirely.
This patch contents itself with changing only the interface to
usb_buffer_map_sg() and friends: The pipe argument is replaced with a
direction flag. That can be done easily because those routines get
used in only one place.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as945) adds a bit to urb->transfer_flags for recording the
direction of the URB. The bit is set/cleared automatically in
usb_submit_urb() so drivers don't have to worry about it (although as
a result, it isn't valid until the URB has been submitted). Inline
routines are added for easily checking an URB's direction. They
replace calls to usb_pipein in the DMA-mapping parts of hcd.c.
For non-control endpoints, the direction is determined directly from
the endpoint descriptor. However control endpoints are
bi-directional; for them the direction is determined from the
bRequestType byte and the wLength value in the setup packet.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as944) adds an explicit "enabled" field to the
usb_host_endpoint structure and uses it in place of the current
mechanism. This is merely a time-space tradeoff; it makes checking
whether URBs may be submitted to an endpoint simpler. The existing
mechanism is efficient when converting urb->pipe to an endpoint
pointer, but it's not so efficient when urb->ep is used instead.
As a side effect, the procedure for enabling an endpoint is now a
little more complicated. The ad-hoc inline code in usb.c and hub.c
for enabling ep0 is now replaced with calls to usb_enable_endpoint,
which is no longer static.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as943) prepares the way for eliminating urb->pipe by
introducing an endpoint pointer into struct urb. For now urb->ep
is set by usb_submit_urb() from the pipe value; eventually drivers
will set it themselves and we will remove urb->pipe completely.
The patch also adds new inline routines to retrieve an endpoint
descriptor's number and transfer type, essentially as replacements for
usb_pipeendpoint and usb_pipetype.
usb_submit_urb(), usb_hcd_submit_urb(), and usb_hcd_unlink_urb() are
converted to use the new field and new routines. Other parts of
usbcore will be converted in later patches.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as965) disables autosuspend by default for all USB devices
other than hubs. We are seeing too many devices that can't suspend or
resume properly, the blacklist is growing unreasonably quickly, and
this sort of thing should be handled in userspace.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like have the attached patch added to Linux kernel. The three
usb flash memories listed in the patch are being used in Intel's
ClassmatePC and need USB_QUIRK_RESET_RESUME to work reliably when
resuming from ram.
This patch fixes the order of list_add_tail() arguments in
usb_store_new_id() so the list can have more than one single element.
Signed-off-by: Nathael Pajani <nathael.pajani@cpe.fr>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
That drive is quite odd. It has 2K sectors, times out getting string
descriptors and needs a quirk.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as986) prevents the troublesome Genesys USB-IDE adapter
from autosuspending. It may not be necessary for all such devices,
but the one in Bugzilla #8892 sometimes fails to resume.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as985) prevents the SGS THomson Microelectronics 4in1 card
reader from autosuspending. This resolves Bugzilla #8885.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes a regression for userspace programs that were relying on these events.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Andreas Jellinghaus <aj@ciphirelabs.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Recent versions of the Linux kernel auto-suspend attached USB devices.
After this happens to the Canon EOS 5D camera, the camera's interrupt endpoints
don't seem to wake back up correctly, causing further use with libgphoto2
to fail with a -114 "OS error in camera communication" error.
A similar fix is probably necessary for this camera in PTP mode, which
identifies as USB product id 0x3102, but we haven't tested this.
As part of our testing process, we tried the USB_QUIRK_RESET_RESUME
quirk also, it's not helpful in this case.
Signed-off-by: Raj Kumar <rkumar@archive.org>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
