Use DEFINE_PCI_DEVICE_TABLE() to make PCI device ids go to
.devinit.rodata section, so they can be discarded in some cases,
and make them const.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* fix/misc:
ALSA: ca0106 - Fix the max capture buffer size
ALSA: OSS sequencer should be initialized after snd_seq_system_client_init
ALSA: sound/isa: convert nested spin_lock_irqsave to spin_lock
The capture buffer size with 64kB seems broken with CA0106.
At least, either the update timing or the DMA position is wrong,
and this screws up pulseaudio badly.
This patch restricts the max buffer size less than that to make life
a bit easier.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Cc: <stable@kernel.org>
Here's a patch on top of the others to use CREATIVE and ECTIVA
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
SNDRV_PCM_SUBCLASS_GENERIC_MIX is mostly for h/w multi-stream playback
devices, but ca0106 and emu10k1x don't support it (unlike emu10k1).
We shouldn't set that flag to avoid confusion.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)
Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The capture with 44.1kHz on ca0106 seems to cause loud noises on
later playbacks, which doesn't support 44.1kHz. A simple fix is to
disable 44.1kHz, as the "default" PCM with dsnoop is anyway only with
48kHz.
Reference: Novell bnc#447624
https://bugzilla.novell.com/show_bug.cgi?id=447624
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added "IEC958 PCM Stream" controls for the per-stream IEC958 status
bits. Using this instead of "IEC958 Default" is safer since the status
bits will be recovered to the default states after closing the PCM
stream.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch removes an inconsistency that became apparent when I
documented the fields of snd_ca0106_details. spi_dac is always
used in a 'boolean' sense, so this cleanup should make no difference.
[Actually, there is one place checking explicitly spi_dac == 1, so
this will change the behavior. But, supposing it's rather a typo,
I apply this clean-up patch -- tiwai]
Signed-off-by: Ben Stanley <Ben.Stanley@exemail.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The return value of pci_enable_device() must be checked even in resume
callback:
sound/pci/ca0106/ca0106_main.c:1779: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct a previous patch for the ca0106 onboard the MSI K8N Diamond PLUS
motherboard. Confirmed to have Line/Mic/Aux working for input, and sound
output working as expected.
Signed-off-by: Travis Place <wishie@wishie.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added an entry for another MSI K8N Diamond mobo with SSID 1102:1009.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The irq handler of PCI drivers must be released before releasing other
resources since the handler for a shared irq can be still called and
may access the freed resource again.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
change to intr_enable as per the two functions it is defined in.
sound/pci/ca0106/ca0106_main.c:438:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ca0106/ca0106_main.c:159:12: originally declared here
sound/pci/ca0106/ca0106_main.c:449:15: warning: symbol 'enable' shadows an earlier one
sound/pci/ca0106/ca0106_main.c:159:12: originally declared here
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Set the SNDRV_PCM_INFO_SYNC_START flag and the substream's sync ID
(only) if the substream actually can be linked to another one.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
It is possible to have linked substreams that belong to different cards
and/or different drivers. This patch changes some drivers to make sure
that they do not incorrectly try to handle substreams of a different
card.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
The init sequence set a number of registers more than once to different
values. It's only necessary to set them once to their final values.
It also never actually updated the digital attenuation settings.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add more symbol name for SPI register values. Change the SPI_XXX_BIT defines
from the bit number to a mask. Saves having to write (1<<SPI_XXX_BIT) all the
time to convert to mask. We never end up wanting the bit number.
Use all the symbol names for the SPI DAC init sequence. The sequence is
exactly the same as it was before.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
For cards with an SPI DAC (SB Live 24-bit / Audigy SE), power down channels
0-2 when not in use. They are powered up on PCM open and down again on PCM
close. Channel 4 (== Front) is not powered down, as it is used for capture
feedback. Powering it down would effectively kill line in pass-through.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add four mute controls for the analog output channels for cards that use
an SPI DAC, like the SB0570 SB Live! 24-bit / Audigy SE. The Wolfson DAC
doesn't support muting left/right so the controls are mono.
The chip state struct gets a 32-byte array to act as a shadow of the spi
dac registers. Only two registers are used for mute, but more would be
needed for analog gain, de-emphasis, DAC power down, phase inversion, and
other features.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
This card is just a normal SB Live 24bit,
but under a different marketing name.
Signed-off-by: James Courtier-Dutton <James@superbug.co.uk>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Added a new macro snd_pcm_group_for_each_entry() just for code cleanup.
Old macros, snd_pcm_group_for_each() and snd_pcm_group_substream_entry(),
are removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the missing device assignment before creating sysfs tree.
This caused the insufficient device permissions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix IRQ flags for PCI devices.
The shared IRQs for PCI devices shouldn't be allocated with
IRQF_DISABLED. Also, when MSI is enabled, IRQF_SHARED shouldn't
be used.
The patch removes unnecessary cast in request_irq and free_irq,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix the type of PCI revision to char from int and avoid invalid
assignment with pointer cast.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
