o With introduction of kexec as boot-loader, the assumption that parameter
segment will always be loaded at lower address than kernel and will be
addressable by early bootup page tables is no longer valid. In kexec on
panic case parameter segment might well be loaded beyond kernel image and
might not be addressable by early boot page tables.
o This case might hit in the scenario where user has reserved a chunk of
memory for second kernel, for example 16MB to 64MB, and has also built
second kernel for physical memory location 16MB. In this case kexec has no
choice but to load the parameter segment at a higher address than new kernel
image at safe location where new kernel does not stomp it.
o Though problem should automatically go away once relocatable kernel for i386
is in place and kexec can determine the location of new kernel at run time
and load parameter segment at lower address than kernel image. But till then
this patch can go in (assuming it does not break something else).
o This patch moves up the boot parameter saving code. Now boot parameters
are copied out in protected mode before page tables are initialized. This
will ensure that parameter segment is always addressable irrespective of
its physical location.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If the virtual 86 machine reaches an instruction which raises a General
Protection Fault (such as CLI or STI), the instruction is emulated (in
handle_vm86_fault). However, the emulation ignored the TF bit, so the
hardware debug interrupt was not invoked after such an emulated instruction
(and the DOS debugger missed it).
This patch fixes the problem by emulating the hardware debug interrupt as
the last action before control is returned to the VM86 program.
Signed-off-by: Petr Tesarik <kernel@tesarici.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The memory descriptors that comprise the EFI memory map are not fixed in
stone such that the size could change in the future. This uses the memory
descriptor size obtained from EFI to iterate over the memory map entries
during boot. This enables the removal of an x86 specific pad (and ifdef)
in the EFI header. I also couldn't stomach the broken up nature of the
function to put EFI runtime calls into virtual mode any longer so I fixed
that up a bit as well.
For reference, this patch only impacts x86.
Signed-off-by: Matt Tolentino <matthew.e.tolentino@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only use read_timer_tsc only when CPU has TSC. Thanks to Andrea for
pointing this out. Should not be issue on any platforms as all recent
systems that has HPET also has CPUs that supports TSC. The patch is still
required for correctness.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch pushes the creation of a rare signal frame (SIGBUS or SIGSEGV)
into a separate function, thus saving stackspace in the main
do_page_fault() stackframe. The effect is 132 bytes less of stack used by
the typical do_page_fault() invocation - resulting in a denser
cache-layout.
(Another minor effect is that in case of kernel crashes that come from a
pagefault, we add less space to the already existing frame, giving the
crash functions a slightly higher chance to do their stuff without
overflowing the stack.)
(The changes also result in slightly cleaner code.)
argument bugfix from "Guillaume C." <guichaz@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I don't think we need to call hugetlb_clean_stale_pgtable() anymore
in 2.6.13 because of the rework with free_pgtables(). It now collect
all the pte page at the time of munmap. It used to only collect page
table pages when entire one pgd can be freed and left with staled pte
pages. Not anymore with 2.6.13. This function will never be called
and We should turn it into a BUG_ON.
I also spotted two problems here, not Adam's fault :-)
(1) in huge_pte_alloc(), it looks like a bug to me that pud is not
checked before calling pmd_alloc()
(2) in hugetlb_clean_stale_pgtable(), it also missed a call to
pmd_free_tlb. I think a tlb flush is required to flush the mapping
for the page table itself when we clear out the pmd pointing to a
pte page. However, since hugetlb_clean_stale_pgtable() is never
called, so it won't trigger the bug.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Cc: Adam Litke <agl@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For demand faulting, we cannot assume that the page tables will be
populated. Do what the rest of the architectures do and test p?d_present()
while walking down the page table.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Initial Post (Wed, 17 Aug 2005)
This patch moves the
if (! pte_none(*pte))
hugetlb_clean_stale_pgtable(pte);
logic into huge_pte_alloc() so all of its callers can be immune to the bug
described by Kenneth Chen at http://lkml.org/lkml/2004/6/16/246
> It turns out there is a bug in hugetlb_prefault(): with 3 level page table,
> huge_pte_alloc() might return a pmd that points to a PTE page. It happens
> if the virtual address for hugetlb mmap is recycled from previously used
> normal page mmap. free_pgtables() might not scrub the pmd entry on
> munmap and hugetlb_prefault skips on any pmd presence regardless what type
> it is.
Unless I am missing something, it seems more correct to place the check inside
huge_pte_alloc() to prevent a the same bug wherever a huge pte is allocated.
It also allows checking for this condition when lazily faulting huge pages
later in the series.
Signed-off-by: Adam Litke <agl@us.ibm.com>
Cc: <linux-mm@kvack.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With cleanups from Dave Hansen <haveblue@us.ibm.com>
SPARSEMEM_EXTREME makes mem_section a one dimensional array of pointers to
mem_sections. This two level layout scheme is able to achieve smaller
memory requirements for SPARSEMEM with the tradeoff of an additional shift
and load when fetching the memory section. The current SPARSEMEM
implementation is a one dimensional array of mem_sections which is the
default SPARSEMEM configuration. The patch attempts isolates the
implementation details of the physical layout of the sparsemem section
array.
SPARSEMEM_EXTREME requires bootmem to be functioning at the time of
memory_present() calls. This is not always feasible, so architectures
which do not need it may allocate everything statically by using
SPARSEMEM_STATIC.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Bob Picco <bob.picco@hp.com>
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Minor fallout from my upcoming __attribute__((format(printf,x,y)))
patches. The variable 'result' is untouched, so this patch just removes
it.
Signed-off-by: Mika Kukkonen <mikukkon@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Ho-hum, did not notice there was more printf fixes for cpufreq (you
should see the amount I have for isdn and reiser ...). Sorry for noise.
Signed-off-by: Mika Kukkonen <mikukkon@gmail.com>
Signed-off-by: Dave Jones <davej@redhat.com>
speedstep_centrino.c:extract_clock() assumes the bus speed of 100MHz, which is
not true with latest laptops. Due to this assumption and due to the encoded
frequency check during initialization, speedstep-centrino driver fails even
on systems that has proper ACPI information to do the P-state transition.
The change below moves the centrino-speedstep detection to be used only
when table based P-state transition is done. For ACPI based P-state
transition, we skip the centrino_cpu identification, and as a result we
don't use the bus speed assumption in extract_clock. This change makes
speedstep-centrino work on Pentium-M based systems, which have more than 100MHz
bus speed.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
I had some time to think about PCI assign issues in 2.6.13-rc series.
The major problem here is that we call pci_assign_unassigned_resources()
way too early - at subsys_initcall level. Therefore we give no chances
to ACPI and PnP routines (called at fs_initcall level) to reserve their
respective resources properly, as the comments in drivers/pnp/system.c
and drivers/acpi/motherboard.c suggest:
/**
* Reserve motherboard resources after PCI claim BARs,
* but before PCI assign resources for uninitialized PCI devices
*/
So I moved the pci_assign_unassigned_resources() call to
pcibios_assign_resources() (fs_initcall), which should hopefully fix a
lot of problems and make PCIBIOS_MIN_IO tweaks unnecessary.
Other changes:
- remove resource assignment code from pcibios_assign_resources(), since
it duplicates pci_assign_unassigned_resources() functionality and
actually does nothing in 2.6.13;
- modify ROM assignment code as per Ben's suggestion: try to use firmware
settings by default (if PCI_ASSIGN_ROMS is not set);
- set CARDBUS_IO_SIZE back to 4K as it's a wonderful stress test for
various setups.
Confirmed by Tero Roponen <teanropo@cc.jyu.fi> (who had problems with
the 4kB CardBus IO size previously).
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It has been reported that the way Linux handles NODEFER for signals is
not consistent with the way other Unix boxes handle it. I've written a
program to test the behavior of how this flag affects signals and had
several reports from people who ran this on various Unix boxes,
confirming that Linux seems to be unique on the way this is handled.
The way NODEFER affects signals on other Unix boxes is as follows:
1) If NODEFER is set, other signals in sa_mask are still blocked.
2) If NODEFER is set and the signal is in sa_mask, then the signal is
still blocked. (Note: this is the behavior of all tested but Linux _and_
NetBSD 2.0 *).
The way NODEFER affects signals on Linux:
1) If NODEFER is set, other signals are _not_ blocked regardless of
sa_mask (Even NetBSD doesn't do this).
2) If NODEFER is set and the signal is in sa_mask, then the signal being
handled is not blocked.
The patch converts signal handling in all current Linux architectures to
the way most Unix boxes work.
Unix boxes that were tested: DU4, AIX 5.2, Irix 6.5, NetBSD 2.0, SFU
3.5 on WinXP, AIX 5.3, Mac OSX, and of course Linux 2.6.13-rcX.
* NetBSD was the only other Unix to behave like Linux on point #2. The
main concern was brought up by point #1 which even NetBSD isn't like
Linux. So with this patch, we leave NetBSD as the lonely one that
behaves differently here with #2.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The acpi-cpufreq driver does a P-state get after a P-state set
to verify whether set went through successfully. This test
is kind of redundant as set goes throught most of the times,
and the test is also expensive as a get of P-states can
take a lot of time (same as a set operation) as it goes
through SMM mode. Effectively, we are doubling the P-state
latency due to this get opertion.
momdule parameter "acpi_pstate_strict" restores orginal paranoia.
http://bugzilla.kernel.org/show_bug.cgi?id=5129
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Delete the ability to build an ACPI kernel that does
not include PCI support. When such a machine is created
and it requires a tuned kernel, send a patch.
http://bugzilla.kernel.org/show_bug.cgi?id=1364
Signed-off-by: Len Brown <len.brown@intel.com>
i386 floating-point exception handling has a bug that can cause error
code 0 to be sent instead of the proper code during signal delivery.
This is caused by unconditionally checking the IS and c1 bits from the
FPU status word when they are not always relevant. The IS bit tells
whether an exception is a stack fault and is only relevant when the
exception is IE (invalid operation.) The C1 bit determines whether a
stack fault is overflow or underflow and is only relevant when IS and IE
are set.
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm trying to get the nmi working with my laptop (IBM ThinkPad G41) and after
debugging it a while, I found that the nmi code doesn't want to set it up for
this particular CPU.
Here I have:
$ cat /proc/cpuinfo
processor : 0
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Mobile Intel(R) Pentium(R) 4 CPU 3.33GHz
stepping : 1
cpu MHz : 3320.084
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni
monitor ds_cpl est tm2 cid xtpr
bogomips : 6642.39
processor : 1
vendor_id : GenuineIntel
cpu family : 15
model : 4
model name : Mobile Intel(R) Pentium(R) 4 CPU 3.33GHz
stepping : 1
cpu MHz : 3320.084
cache size : 1024 KB
physical id : 0
siblings : 2
core id : 0
cpu cores : 1
fdiv_bug : no
hlt_bug : no
f00f_bug : no
coma_bug : no
fpu : yes
fpu_exception : yes
cpuid level : 3
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge
mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm pbe pni
monitor ds_cpl est tm2 cid xtpr
bogomips : 6637.46
And the following code shows:
$ cat linux-2.6.13-rc6/arch/i386/kernel/nmi.c
[...]
void setup_apic_nmi_watchdog (void)
{
switch (boot_cpu_data.x86_vendor) {
case X86_VENDOR_AMD:
if (boot_cpu_data.x86 != 6 && boot_cpu_data.x86 != 15)
return;
setup_k7_watchdog();
break;
case X86_VENDOR_INTEL:
switch (boot_cpu_data.x86) {
case 6:
if (boot_cpu_data.x86_model > 0xd)
return;
setup_p6_watchdog();
break;
case 15:
if (boot_cpu_data.x86_model > 0x3)
return;
Here I get boot_cpu_data.x86_model == 0x4. So I decided to change it and
reboot. I now seem to have a working NMI. So, unless there's something know
to be bad about this processor and the NMI. I'm submitting the following
patch.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Acked-by: Mikael Pettersson <mikpe@csd.uu.se>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since early CPU identify is in this information is already available
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the fix to align node_end_pfns to a proper location. The earlier fix
made the node_remap_start_vaddr to get misaligned causing remap_numa_kva to
barf again :-/
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch add stubs to allow the visws subarch to link again.
Signed-off-by: Tom Duffy <thomas.duffy.99@alumni.brown.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another x86 subarchitecture bit I missed. This adds both
machine_emergency_restart missed in my reboot fixes and
machine_shutdown needed for kexec support.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Here is one more bit of breakage my x86 sub-architecture
confusion caused.
Add machine_shutdown to voyager so it will compile with CONFIG_KEXEC.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
[PATCH] i386: Implement machine_emergency_reboot
introduced this new function into arch/i386/reboot.c. However,
subarchitectures are entitled to implement their own copies of reboot.c
from which this new function is now missing.
It looks like visws will also need a similar fixup
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Current acpi_register_gsi() function has no way to indicate errors to its
callers even though acpi_register_gsi() can fail to register gsi because of
some reasons (out of memory, lack of interrupt vectors, incorrect BIOS, and so
on). As a result, caller of acpi_register_gsi() cannot handle the case that
acpi_register_gsi() fails. I think failure of acpi_register_gsi() should be
handled properly.
This series of patches changes acpi_register_gsi() to return negative value on
error, and also changes callers of acpi_register_gsi() to handle failure of
acpi_register_gsi().
This patch changes the type of return value of acpi_register_gsi() from
"unsigned int" to "int" to indicate an error. If acpi_register_gsi() fails to
register gsi, it returns negative value.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Len Brown <len.brown@intel.com>
We had a user whose apps weren't working correctly because his "rtc" wasn't
working fully.
For the sake of simplicity, it seems sensible to always enable HPET RTC
emulation.
Remove a special config option for HPET_EMULATE_RTC and make it directly
depend on HPET_TIMER and RTC. This will avoid the hangs when EMULATE_RTC
is not configured and when some userlevel script depends on RTC interrupt,
as in:
http://bugzilla.kernel.org/show_bug.cgi?id=4904
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug found by Grant Coady <lkml@dodo.com.au>'s autobuild setup.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We know that the randomisation slows down some workloads on Transmeta CPUs
by quite large amounts. We think it's because the CPU needs to recode the
same x86 instructions when they pop up at a different virtual address after
a fork+exec.
So disable randomization by default on those CPUs.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes sys_set_zone_reclaim() for now. While i'm sure Martin is
trying to solve a real problem, we must not hard-code an incomplete and
insufficient approach into a syscall, because syscalls are pretty much
for eternity. I am quite strongly convinced that this syscall must not
hit v2.6.13 in its current form.
Firstly, the syscall lacks basic syscall design: e.g. it allows the
global setting of VM policy for unprivileged users. (!) [ Imagine an
Oracle installation and a SAP installation on the same NUMA box fighting
over the 'optimal' setting for this flag. What will they do? Will they
try to set the flag to their own preferred value every second or so? ]
Secondly, it was added based on a single datapoint from Martin:
http://marc.theaimsgroup.com/?l=linux-mm&m=111763597218177&w=2
where Martin characterizes the numbers the following way:
' Run-to-run variability for "make -j" is huge, so these numbers aren't
terribly useful except to see that with reclaim the benchmark still
finishes in a reasonable amount of time. '
in other words: the fundamental problem has likely not been solved, only
a tendential move into the right direction has been observed, and a
handful of numbers were picked out of a set of hugely variable results,
without showing the variability data. How much variance is there
run-to-run?
I'd really suggest to first walk the walk and see what's needed to get
stable & predictable kernel compilation numbers on that NUMA box, before
adding random syscalls to tune a particular aspect of the VM ... which
approach might not even matter once the whole picture has been analyzed
and understood!
The third, most important point is that the syscall exposes VM tuning
internals in a completely unstructured way. What sense does it make to
have a _GLOBAL_ per-node setting for 'should we go to another node for
reclaim'? If then it might make sense to do this per-app, via numalib or
so.
The change is minimalistic in that it doesnt remove the syscall and the
underlying infrastructure changes, only the user-visible changes. We
could perhaps add a CAP_SYS_ADMIN-only sysctl for this hack, a'ka
/proc/sys/vm/swappiness, but even that looks quite counterproductive
when the generic approach is that we are trying to reduce the number of
external factors in the VM balance picture.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add reference count and disable ACPI PCI Interrupt Link
when no device still uses it.
Warn when drivers have not released Link at suspend time.
http://bugzilla.kernel.org/show_bug.cgi?id=3469
Signed-off-by: David Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Otherwise a platform that supports ACPI based cpufreq
and boots up at lowest possible speed could stay there
forever. This because the governor may request max speed,
but the code doesn't update if there is no change in
speed, and it assumed the initial state of max speed.
http://bugzilla.kernel.org/show_bug.cgi?id=4634
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The patch addresses a problem with ACPI SCI interrupt entry, which gets
re-used, and the IRQ is assigned to another unrelated device. The patch
corrects the code such that SCI IRQ is skipped and duplicate entry is
avoided. Second issue came up with VIA chipset, the problem was caused by
original patch assigning IRQs starting 16 and up. The VIA chipset uses
4-bit IRQ register for internal interrupt routing, and therefore cannot
handle IRQ numbers assigned to its devices. The patch corrects this
problem by allowing PCI IRQs below 16.
Signed-off by: Natalie Protasevich <Natalie.Protasevich@unisys.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While reserving KVA for lmem_maps of node, we have to make sure that
node_remap_start_pfn[] is aligned to a proper pmd boundary.
(node_remap_start_pfn[] gets its value from node_end_pfn[])
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:740: warning: unused variable `vid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:739: warning: unused variable `fid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:743: warning: unused variable `vid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:742: warning: unused variable `fid'
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:746: `fid' undeclared (first use in this function)
arch/i386/kernel/cpu/cpufreq/powernow-k8.c:746: `vid' undeclared (first use in this function)
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
For some reason I was telling my inline assembly that the
input argument was an output argument.
Playing in the trampoline code I have seen a couple of
instances where lgdt get the wrong size (because the
trampolines run in 16bit mode) so use lgdtl and lidtl to
be explicit.
Additionally gcc-3.3 and gcc-3.4 want's an lvalue for a
memory argument and it doesn't think an array of characters
is an lvalue so use a packed structure instead.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Somewhere recently, the TSC got re-enabled for timekeeping on NUMAQ
machines. However, the hardware makes these get unsynchronized quite
badly. So badly, in fact, that the code to fix up the skew can just hang
on boot.
This patch re-disables them. It's nicely confined to the numaq.c file. It
would be great if this could make it into 2.6.13, I think it counts as a
bugfix.
Tested on a 16-proc 4-node NUMAQ.
Signed-off-by: Dave Hansen <haveblue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
powernow-k8.c:110: warning: `hi' may be used uninitialized in this function
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
can be encoded in the current driver's 4 bit frequency
field. This patch updates the driver to support Rev F
including 6 bit FIDs and processor ID updates.
This should apply cleanly whether or not the dual-core
bugfix I sent out last week is applied. I'd prefer
that both get applied, of course.
Signed-off-by: David Keck <david.keck@amd.com>
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
each core be created in the _cpu_init function
call. The cpufreq infrastructure doesn't call
_cpu_init for the second core in each processor.
Some systems crashed when _get was called with
an odd-numbered core because it tried to
dereference a NULL pointer since the data
structure had not been created.
The attached patch solves the problem by
initializing data structures for all shared
cores in the _cpu_init function. It should
apply to 2.6.12-rc6 and has been tested by
AMD and Sun.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch:
http://marc.theaimsgroup.com/?l=bk-commits-head&m=111955644929114&w=2
uncovered a k7m bios bug, where the VT82C686A router is reported as
being "586-compatible". The two chips have different pirq mapping, so
this leads to "irq routing conflict" on many pci devices.
The suggested fix was discussed with Aleksey Gorelov, who helped me
to identify the problem as a probable bios bug.
Signed-off-by: Giancarlo Formicuccia <giancarlo.formicuccia@gmail.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sys_get_thread_area does not memset to 0 its struct user_desc info before
copying it to user space... since sizeof(struct user_desc) is 16 while the
actual datas which are filled are only 12 bytes + 9 bits (across the
bitfields), there is a (small) information leak.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There's no help text for CONFIG_DEBUG_STACKOVERFLOW - add one.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
powernow-k8.c: In function `query_current_values_with_pending_wait':
powernow-k8.c:110: warning: `hi' may be used uninitialized in this function
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
machine_power_off now always switches to the boot cpu so there
is no reason for APM to also do that.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Call machine_shutdown() to move to the boot cpu
and disable apics. Both acpi_power_off and
apm_power_off want to move to the boot cpu.
and we are already disabling the local apics
so calling machine_shutdown simply reuses
code.
ia64 doesn't have a special path in power_off
for efi so there is no reason i386 should. If
we really need to call the efi power off path
the efi driver can set pm_power_off like everyone
else.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This appears to be a typo I introduced when cleaning
this code up earlier. Ooops.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
set_cpus_allowed is not safe in interrupt context
and disabling apics is complicated code so don't
call machine_shutdown on i386 from emergency_restart().
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
machine_restart, machine_halt and machine_power_off are machine
specific hooks deep into the reboot logic, that modules
have no business messing with. Usually code should be calling
kernel_restart, kernel_halt, kernel_power_off, or
emergency_restart. So don't export machine_restart,
machine_halt, and machine_power_off so we can catch buggy users.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is no longer valid to not replace instructions, since we depend on
different behaviour depending on CPU capabilities.
If you need to limit the capabilities of the replacements (because the
boot CPU has features that non-boot CPU's do not have, for example), you
need to explicitly disable those capabilities that are not shared across
all CPU's.
For example, if your boot CPU has FXSR, but other CPU's in your system
do not, you need to use the "nofxsr" kernel command line, not disable
instruction replacement per se.
It's really just a single instruction, conditional on whether the CPU
supports FXSR or not, so implement it as such instead of making it a
function that queries FXSR dynamically.
This means that the instruction just gets automatically rewritten to the
correct one at boot-time.
These days %gs is normally the TLS segment, so it's no longer zero. As
a result, we shouldn't just assume that %fs/%gs tend to be zero
together, but test them independently instead.
Also, fix setting of debug registers to use the "next" pointer instead
of "current". It so happens that the scheduler will have set the new
current pointer before calling __switch_to(), but that's just an
implementation detail.
More fallout from the i386_ksyms.c cleanups.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch:
[PATCH] Remove i386_ksyms.c, almost
made files like smp.c do their own EXPORT_SYMBOLS. This means that all
subarchitectures that override these symbols now have to do the exports
themselves. This patch adds the exports for voyager (which is the most
affected since it has a separate smp harness). However, someone should
audit all the other subarchitectures to see if any others got broken.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
inotify is intended to correct the deficiencies of dnotify, particularly
its inability to scale and its terrible user interface:
* dnotify requires the opening of one fd per each directory
that you intend to watch. This quickly results in too many
open files and pins removable media, preventing unmount.
* dnotify is directory-based. You only learn about changes to
directories. Sure, a change to a file in a directory affects
the directory, but you are then forced to keep a cache of
stat structures.
* dnotify's interface to user-space is awful. Signals?
inotify provides a more usable, simple, powerful solution to file change
notification:
* inotify's interface is a system call that returns a fd, not SIGIO.
You get a single fd, which is select()-able.
* inotify has an event that says "the filesystem that the item
you were watching is on was unmounted."
* inotify can watch directories or files.
Inotify is currently used by Beagle (a desktop search infrastructure),
Gamin (a FAM replacement), and other projects.
See Documentation/filesystems/inotify.txt.
Signed-off-by: Robert Love <rml@novell.com>
Cc: John McCutchan <ttb@tentacle.dhs.org>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Create a new top-level menu named "Networking" thus moving
net related options and protocol selection way from the drivers
menu and up on the top-level where they belong.
To implement this all architectures has to source "net/Kconfig" before
drivers/*/Kconfig in their Kconfig file. This change has been
implemented for all architectures.
Device drivers for ordinary NIC's are still to be found
in the Device Drivers section, but Bluetooth, IrDA and ax25
are located with their corresponding menu entries under the new
networking menu item.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
http://bugme.osdl.org/show_bug.cgi?id=4016
Written-by: David Shaohua Li <shaohua.li@intel.com>
Acked-by: Adam Belay <abelay@novell.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add a new section called ".data.read_mostly" for data items that are read
frequently and rarely written to like cpumaps etc.
If these maps are placed in the .data section then these frequenly read
items may end up in cachelines with data is is frequently updated. In that
case all processors in an SMP system must needlessly reload the cachelines
again and again containing elements of those frequently used variables.
The ability to share these cachelines will allow each cpu in an SMP system
to keep local copies of those shared cachelines thereby optimizing
performance.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Shobhit Dayal <shobhit@calsoftinc.com>
Signed-off-by: Christoph Lameter <christoph@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There has been some discuss about solving the SMP MTRR suspend/resume
breakage, but I didn't find a patch for it. This is an intent for it. The
basic idea is moving mtrr initializing into cpu_identify for all APs (so it
works for cpu hotplug). For BP, restore_processor_state is responsible for
restoring MTRR.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We get sporadic reports of `__iounmap: bad address' coming out. Add a
dump_stack() to find the culprit.
Try to identify which subsystem is having iounmap() problems.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following renames arch_init, a kprobes function for performing any
architecture specific initialization, to arch_init_kprobes in order to
cleanup the namespace.
Also, this patch adds arch_init_kprobes to sparc64 to fix the sparc64 kprobes
build from the last return probe patch.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The dynamic pci id logic has been bothering me for a while, and now that
I started to look into how to move some of this to the driver core, I
thought it was time to clean it all up.
It ends up making the code smaller, and easier to follow, and fixes a
few bugs at the same time (dynamic ids were not being matched
everywhere, and so could be missed on some call paths for new devices,
semaphore not needed to be grabbed when adding a new id and calling the
driver core, etc.)
I also renamed the function pci_match_device() to pci_match_id() as
that's what it really does.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
- Add sanity check for io[port,mem]_resource in setup-bus.c. These
resources look like "free" as they have no parents, but obviously
we must not touch them.
- In i386.c:pci_allocate_bus_resources(), if a bridge resource cannot be
allocated for some reason, then clear its flags. This prevents any child
allocations in this range, so the setup-bus code will work with a clean
resource sub-tree.
- i386.c:pcibios_enable_resources() doesn't enable bridges, as it checks
only resources 0-5, which looks like a clear bug to me. I suspect it
might break hotplug as well in some cases.
From: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Variable "c" was declared as an unsigned int, but used in:
125 for (i=0 ; (c=read(fd, buf, sizeof(buf)))>0 ; i+=c )
126 if (write(1, buf, c) != c)
127 die("Write call failed");
(akpm: read() can return -1. If it does, we fill the disk up with garbage).
Signed-off-by: Zaur Kambarov <zkambarov@coverity.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we have access to the whole MCFG table, let's properly use it
for all pci device accesses (as that's what it is there for, some boxes
don't put all the busses into one entry.)
If, for some reason, the table is incorrect, we fallback to the "old
style" of mmconfig accesses, namely, we just assume the first entry in
the table is the one for us, and blindly use it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is the first step in properly handling the MCFG PCI table.
It defines the structures properly, and saves off the table so that the
pci mmconfig code can access it. It moves the parsing of the table a
little later in the boot process, but still before the information is
needed.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the following new interfaces for I/O xAPIC
hotplug. The implementation of these interfaces depends on each
architecture.
o int acpi_register_ioapic(acpi_handle handle, u64 phys_addr,
u32 gsi_base);
This new interface is to add a new I/O xAPIC specified by
phys_addr and gsi_base pair. phys_addr is the physical address
to which the I/O xAPIC is mapped and gsi_base is global system
interrupt base of the I/O xAPIC. acpi_register_ioapic returns
0 on success, or negative value on error.
o int acpi_unregister_ioapic(acpi_handle handle, u32 gsi_base);
This new interface is to remove a I/O xAPIC specified by
gsi_base. acpi_unregister_ioapic returns 0 on success, or
negative value on error.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When you hot-plug a (root) bridge hierarchy, it may have p2p bridges and
devices attached to it that have not been configured by firmware. In this
case, we need to configure the devices before starting them. This patch
separates device start from device scan so that we can introduce the
configuration step in the middle.
I kept the existing semantics for pci_scan_bus() since there are a huge number
of callers to that function.
Also, I have no way of testing the changes I made to the parisc files, so this
needs review by those folks. Sorry for the massive cross-post, this touches
files in many different places.
Signed-off-by: Rajesh Shah <rajesh.shah@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I updated this to remove unnecessary variable initialization, make
check_routing be inline only and not __init, switch to strtoul, and
formatting fixes as per Randy Dunlap's recommendations.
I updated this to change pirq_table_addr to a long, and to add a warning
msg if the PIRQ table wasn't found at the specified address, as per thread
with Matthew Wilcox.
In our hardware situation, the BIOS is unable to store or generate it's PIRQ
table in the F0000h-100000h standard range. This patch adds a pci kernel
parameter, pirqaddr to allow the bootloader (or BIOS based loader) to inform
the kernel where the PIRQ table got stored. A beneficial side-effect is that,
if one's BIOS uses a static address each time for it's PIRQ table, then
pirqaddr can be used to avoid the $pirq search through that address block each
time at boot for normal PIRQ BIOSes.
Signed-off-by: Jaya Kumar <jayalk@intworks.biz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The following patch contains the i386 specific changes for the new
return probe design. Changes include:
* Removing the architecture specific functions for querying a return probe
instance off a stack address
* Complete rework onf arch_prepare_kretprobe() and trampoline_probe_handler()
* Removing trampoline_post_handler()
* Adding arch_init() so that now we handle registering the return probe
trampoline instead of kernel/kprobes.c doing it
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I believe at least for seccomp it's worth to turn off the tsc, not just for
HT but for the L2 cache too. So it's up to you, either you turn it off
completely (which isn't very nice IMHO) or I recommend to apply this below
patch.
This has been tested successfully on x86-64 against current cogito
repository (i686 compiles so I didn't bother testing ;). People selling
the cpu through cpushare may appreciate this bit for a peace of mind.
There's no way to get any timing info anymore with this applied
(gettimeofday is forbidden of course). The seccomp environment is
completely deterministic so it can't be allowed to get timing info, it has
to be deterministic so in the future I can enable a computing mode that
does a parallel computing for each task with server side transparent
checkpointing and verification that the output is the same from all the 2/3
seller computers for each task, without the buyer even noticing (for now
the verification is left to the buyer client side and there's no
checkpointing, since that would require more kernel changes to track the
dirty bits but it'll be easy to extend once the basic mode is finished).
Eliminating a cold-cache read of the cr4 global variable will save one
cacheline during the tlb flush while making the code per-cpu-safe at the
same time. Thanks to Mikael Pettersson for noticing the tlb flush wasn't
per-cpu-safe.
The global tlb flush can run from irq (IPI calling do_flush_tlb_all) but
it'll be transparent to the switch_to code since the IPI won't make any
change to the cr4 contents from the point of view of the interrupted code
and since it's now all per-cpu stuff, it will not race. So no need to
disable irqs in switch_to slow path.
Signed-off-by: Andrea Arcangeli <andrea@cpushare.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the CFQ io scheduler to the new time sliced design (cfq
v3). It provides full process fairness, while giving excellent
aggregate system throughput even for many competing processes. It
supports io priorities, either inherited from the cpu nice value or set
directly with the ioprio_get/set syscalls. The latter closely mimic
set/getpriority.
This import is based on my latest from -mm.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
1. Establish a simple API for process freezing defined in linux/include/sched.h:
frozen(process) Check for frozen process
freezing(process) Check if a process is being frozen
freeze(process) Tell a process to freeze (go to refrigerator)
thaw_process(process) Restart process
frozen_process(process) Process is frozen now
2. Remove all references to PF_FREEZE and PF_FROZEN from all
kernel sources except sched.h
3. Fix numerous locations where try_to_freeze is manually done by a driver
4. Remove the argument that is no longer necessary from two function calls.
5. Some whitespace cleanup
6. Clear potential race in refrigerator (provides an open window of PF_FREEZE
cleared before setting PF_FROZEN, recalc_sigpending does not check
PF_FROZEN).
This patch does not address the problem of freeze_processes() violating the rule
that a task may only modify its own flags by setting PF_FREEZE. This is not clean
in an SMP environment. freeze(process) is therefore not SMP safe!
Signed-off-by: Christoph Lameter <christoph@lameter.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
printk() calls should include appropriate KERN_* constant.
Signed-off-by: Christophe Lucas <clucas@rotomalug.org>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are currently two different boot_cpu_logical_apicid variables:
- a global one in mpparse.c
- a static one in smpboot.c
Of these two, only the one in smpboot.c might be used (through
boot_cpu_apicid).
This patch therefore removes the one in mpparse.c .
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove some of the unnecessary differences between arch/i386 and
arch/x86_64. This patch fixes more whitespace issues, some miscellaneous
typos, a wrong URL and a factually incorrect statement about the current
boot sector code.
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch provides purely cosmetic changes and corrects CodingStyle
guide lines related certain issues like below in kexec related files
o braces for one line "if" statements, "for" loops,
o more than 80 column wide lines,
o No space after "while", "for" and "switch" key words
o Changes:
o take-2: Removed the extra tab before "case" key words.
o take-3: Put operator at the end of line and space before "*/"
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we are faulting in kernel it is quite possible this will lead to a
panic. Save trap number, cr2 (in case of page fault) and error_code in the
current thread (these fields already exist for signal delivery but are not
used here).
This helps later kdump crash analyzing from user-space (a script has been
submitted to dig this info out in gdb).
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Cc: <fastboot@lists.osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Makes kexec_crashdump() take a pt_regs * as an argument. This allows to
get exact register state at the point of the crash. If we come from direct
panic assertion NULL will be passed and the current registers saved before
crashdump.
This hooks into two places:
die(): check the conditions under which we will panic when calling
do_exit and go there directly with the pt_regs that caused the fatal
fault.
die_nmi(): If we receive an NMI lockup while in the kernel use the
pt_regs and go directly to crash_kexec(). We're probably nested up badly
at this point so this might be the only chance to escape with proper
information.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for retrieving the address of elf core header if one
is passed in command line.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch provides the interfaces necessary to read the dump contents,
treating it as a high memory device.
Signed off by Hariprasad Nellitheertha <hari@in.ibm.com>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- config option CONFIG_CRASH_DUMP
- Made it dependent on HIGHMEM. This is required as capture kernel treats
the previous kernel's memory as high memmory and stitches a PTE for
accessing it.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch retrieves the max_pfn being used by previous kernel and stores it
in a safe location (saved_max_pfn) before it is overwritten due to user
defined memory map. This pfn is used to make sure that user does not try to
read the physical memory beyond saved_max_pfn.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Problem: Kexec on panic hangs if first kernel is booted with nmi_watchdog
command line parameter. This problem occurs because kexec crash shutdown
code replaces the NMI callback handler. This handler saves the cpu register
states and halts the cpu. If system is booted with nmi_watchdog parameter,
then crashing cpu also runs this nmi handler and halts itself.
o This patch fixes the problem by keeping a track of crashing cpu and not
executing the new nmi handler on crashing cpu.
o There is a dependence on smp_processor_id() function which might return
insane value for cpu, if cpu field of thread_info is corrupted.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CPU does not save ss and esp on stack if execution was already in kernel mode
at the time of NMI occurrence. This leads to saving of erractic values for ss
and esp. This patch fixes the issue.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Following patch exports kexec global variable "crash_notes" to user space
through sysfs as kernel attribute in /sys/kernel.
Signed-off-by: Maneesh Soni <maneesh@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the x86 implementation of the crashkernel option. It reserves a
window of memory very early in the bootup process, so we never use it for
anything but the kernel to switch to when the running kernel panics.
In addition to reserving this memory a resource structure is registered so
looking at /proc/iomem it is clear what happened to that memory.
ISSUES:
Is it possible to implement this in a architecture generic way?
What should be done with architectures that always use an iommu and
thus don't report their RAM memory resources in /proc/iomem?
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In the case of a crash/panic an architecture specific function
machine_crash_shutdown is called. This patch adds to the x86 machine_crash
function the standard kernel code for shutting down apics.
Every line of code added to that function increases the risk that we will call
code after a kernel panic that is not safe.
This patch should not make it to the stable kernel without a being reviewed a
lot more. It is unclear how much a hardned kernel can take when it comes to
misconfigured apics. So since a normal kernel has problems this patch does a
clean shutdown.
It is my expectation this patch will be dropped from future generations of the
kexec work. But for the moment it is a crutch to keep from breaking
everything.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After the kernel panics if we wish to generate an entire machine core file it
is very nice to know the register state at the time the machine crashed.
After long discussion it was realized that if you are going to be saving the
information anyway it is reasonable to store the information in a format that
it will be used and recognized in so the register state is stored in the
standard ELF note format.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
One of the dangers when switching from one kernel to another is what happens
to all of the other cpus that were running in the crashed kernel. In an
attempt to avoid that problem this patch adds a nmi handler and attempts to
shoot down the other cpus by sending them non maskable interrupts.
The code then waits for 1 second or until all known cpus have stopped running
and then jumps from the running kernel that has crashed to the kernel in
reserved memory.
The kernel spin loop is used for the delay as that should behave continue to
be safe even in after a crash.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the i386 implementation of kexec.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Factor out the apic and smp shutdown code from machine_restart so it can be
called by in the kexec reboot path as well.
By switching to the bootstrap cpu by default on reboot I can delete/simplify
some motherboard fixups well.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a problem with reserving memory during boot up of a kernel
built for non-default location. Currently boot memory allocator reserves
the memory required by kernel image, boot allocaotor bitmap etc. It
assumes that kernel is loaded at 1MB (HIGH_MEMORY hard coded to 1024*1024).
But kernel can be built for non-default locatoin, hence existing
hardcoding will lead to reserving unnecessary memory. This patch fixes it.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For one kernel to report a crash another kernel has created we need
to have 2 kernels loaded simultaneously in memory. To accomplish this
the two kernels need to built to run at different physical addresses.
This patch adds the CONFIG_PHYSICAL_START option to the x86 kernel
so we can do just that. You need to know what you are doing and
the ramifications are before changing this value, and most users
won't care so I have made it depend on CONFIG_EMBEDDED
bzImage kernels will work and run at a different address when compiled
with this option but they will still load at 1MB. If you need a kernel
loaded at a different address as well you need to boot a vmlinux.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The vmlinux on i386 does not report the correct physical address of
the kernel. Instead in the physical address field it currently
reports the virtual address of the kernel.
This is patch is a bug fix that corrects vmlinux to report the
proper physical addresses.
This is potentially a help for crash dump analysis tools.
This definitiely allows bootloaders that load vmlinux as a standard
ELF executable. Bootloaders directly loading vmlinux become of
practical importance when we consider the kexec on panic case.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When coming out of apic mode attempt to set the appropriate
apic back into virtual wire mode. This improves on previous versions
of this patch by by never setting bot the local apic and the ioapic
into veritual wire mode.
This code looks at data from the mptable to see if an ioapic has
an ExtInt input to make this decision. A future improvement
is to figure out which apic or ioapic was in virtual wire mode
at boot time and to remember it. That is potentially a more accurate
method, of selecting which apic to place in virutal wire mode.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Eric W. Biederman <ebiederm@xmission.com>
This patch disables interrupt generation from the legacy pic on reboot. Now
that there is a sys_device class it should not be called while drivers are
still using interrupts.
There is a report about this breaking ACPI power off on some systems.
http://bugme.osdl.org/show_bug.cgi?id=4041
However the final comment seems to exonerate this code. So until
I get more information I believe that was a false positive.
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: "Maciej W. Rozycki" <macro@linux-mips.org>
Fix a kexec problem whcih causes local APIC detection failure.
The problem is detect_init_APIC() is called early, before the command line
have been processed. Therefore "lapic" (and "nolapic") have not been seen,
yet.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Eric Biederman <ebiederm@xmission.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch consolidates the CONFIG_PREEMPT and CONFIG_PREEMPT_BKL
preemption options into kernel/Kconfig.preempt. This, besides reducing
source-code, also enables more centralized tweaking of preemption related
options.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes register saving so that each register is only saved once,
and adds missing saving of %cr8 on x86-64. Some reordering so that
save/restore is more logical/safer (segment registers should be restored
after gdt).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_PM_DISK is long gone, but it still managed to survived at few
places.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Using CPU hotplug to support suspend/resume SMP. Both S3 and S4 use
disable/enable_nonboot_cpus API. The S4 part is based on Pavel's original S4
SMP patch.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Experimental CPU hotplug patch for x86_64
-----------------------------------------
This supports logical CPU online and offline.
- Test with maxcpus=1, and then kick other cpu's off to test if init code
is all cleaned up. CONFIG_SCHED_SMT works as well.
- idle threads are forked on demand from keventd threads for clean startup
TBD:
1. Not tested on a real NUMA machine (tested with numa=fake=2)
2. Handle ACPI pieces for physical hotplug support.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Shaohua.li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean CPU states in order to reuse smp boot code for CPU hotplug.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Trival patch for CPU hotplug. In CPU identify part, only did cleaup for intel
CPUs. Need do for other CPUs if they support S3 SMP.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sibling map init per-cpu. Hotplug CPU may change the map at runtime.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make SEP init per-cpu, so it is hotplug safe.
Signed-off-by: Li Shaohua<shaohua.li@intel.com>
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch introduces a startup parameter no_broadcast. When we enable
CONFIG_HOTPLUG_CPU, we dont want to use broadcast shortcut as it has ill
effects on a offline cpu. If we issue broadcast, the IPI is also delivered
to offline cpus, or partially up cpu causing stale IPI's to be handled,
which is a problem and can cause undesirable effects.
Introduces a new startup cmdline option no_ipi_broadcast, that can be
switched at cmdline if necessary.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Acked-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(The i386 CPU hotplug patch provides infrastructure for some work which Pavel
is doing as well as for ACPI S3 (suspend-to-RAM) work which Li Shaohua
<shaohua.li@intel.com> is doing)
The following provides i386 architecture support for safely unregistering and
registering processors during runtime, updated for the current -mm tree. In
order to avoid dumping cpu hotplug code into kernel/irq/* i dropped the
cpu_online check in do_IRQ() by modifying fixup_irqs(). The difference being
that on cpu offline, fixup_irqs() is called before we clear the cpu from
cpu_online_map and a long delay in order to ensure that we never have any
queued external interrupts on the APICs. There are additional changes to s390
and ppc64 to account for this change.
1) Add CONFIG_HOTPLUG_CPU
2) disable local APIC timer on dead cpus.
3) Disable preempt around irq balancing to prevent CPUs going down.
4) Print irq stats for all possible cpus.
5) Debugging check for interrupts on offline cpus.
6) Hacky fixup_irqs() to redirect irqs when cpus go off/online.
7) play_dead() for offline cpus to spin inside.
8) Handle offline cpus set in flush_tlb_others().
9) Grab lock earlier in smp_call_function() to prevent CPUs going down.
10) Implement __cpu_disable() and __cpu_die().
11) Enable local interrupts in cpu_enable() after fixup_irqs()
12) Don't fiddle with NMI on dead cpu, but leave intact on other cpus.
13) Program IRQ affinity whilst cpu is still in cpu_online_map on offline.
Signed-off-by: Zwane Mwaikambo <zwane@linuxpower.ca>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I'm doing the cpu hotplug stress test and found a variable ('ready') is
overflow after several hundreds rounds of cpu hotplug. Here is a fix.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With hpet enabled, cpu hotplug uses some routines marked with __init.
Signed-off-by: Shaohua Li<shaohua.li@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since last dmi quirk looks useless (it just prints 404 compliant url) we can
finally remove central dmi blacklist.
Signed-off-by: Andrey Panin <pazke@donpac.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I8K: Change to use stock dmi infrastructure instead of homegrown
parsing code. The driver now requires box's DMI data to match
list of supported models so driver can be safely compiled-in
by default without fear of it poking into random SMM BIOS
code. DMI checks can be ignored with i8k.ignore_dmi option.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch includes i386 architecture specific changes to support temporary
disarming on reentrancy of probes.
Signed-of-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch moves the lock/unlock of the arch specific kprobe_flush_task()
to the non-arch specific kprobe_flusk_task().
Signed-off-by: Hien Nguyen <hien@us.ibm.com>
Acked-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The architecture independent code of the current kprobes implementation is
arming and disarming kprobes at registration time. The problem is that the
code is assuming that arming and disarming is a just done by a simple write
of some magic value to an address. This is problematic for ia64 where our
instructions look more like structures, and we can not insert break points
by just doing something like:
*p->addr = BREAKPOINT_INSTRUCTION;
The following patch to 2.6.12-rc4-mm2 adds two new architecture dependent
functions:
* void arch_arm_kprobe(struct kprobe *p)
* void arch_disarm_kprobe(struct kprobe *p)
and then adds the new functions for each of the architectures that already
implement kprobes (spar64/ppc64/i386/x86_64).
I thought arch_[dis]arm_kprobe was the most descriptive of what was really
happening, but each of the architectures already had a disarm_kprobe()
function that was really a "disarm and do some other clean-up items as
needed when you stumble across a recursive kprobe." So... I took the
liberty of changing the code that was calling disarm_kprobe() to call
arch_disarm_kprobe(), and then do the cleanup in the block of code dealing
with the recursive kprobe case.
So far this patch as been tested on i386, x86_64, and ppc64, but still
needs to be tested in sparc64.
Signed-off-by: Rusty Lynch <rusty.lynch@intel.com>
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
