The GNU `config.guess' uses "linux-gnu" as the canonical system name.
Fix the list of compiler prefixes checked to spell it correctly.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Adds a JR.HB after halting a TC, to ensure that the TC has really halted.
only modifies the TCSTATUS register when the TC is safely halted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have no guarantee by the generic time code that the timer is stopped
when the ->next_event method is called. Modifying the Timer Initial Count
register while the timer is enabled has UNPREDICTABLE effect according to
the BCM1250/BCM1125/BCM1125H User Manual. So stop the timer before
reprogramming.
This is a paranoia fix; no ill effects have been observed previously.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
For the old minimum of a single tick a value of zero would be programmed
into the init value register which in the BCM1250/BCM1125/BCM1125H User
Manual in the Timer Special Cases section is documented to have
UNPREDICTABLE effect.
Observable sympthoms of this bug were hangs of several seconds on the
console during bootup and later if both dyntick and highres timer options
were activated.
In theory contiguous mode of the timers is also affected but in an act of
hopeless lack of realism I'll assume nobody will ever configure a KERNEL
for HZ > 500kHz but if so I leave that to evolution to sort out.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The range of MIPS_CPU IRQ and the range of LASAT IRQ overlap.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Shadow register support would not possibly have worked on multicore
systems. The support code for it was also depending not on MIPS R2 but
VSMP or SMTC kernels even though it makes perfect sense with UP kernels.
SR sets are a scarce resource and the expected usage pattern is that
users actually hardcode the register set numbers in their code. So fix
the allocator by ditching it. Move the remaining CPU probe bits into
the generic CPU probe.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
iounmap if pci clock is over 33MHz. Cosmetic because the iomap() in this
case is just a bit of address magic.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The recent switch of the Sibyte SOCs from the processor specific cache
managment code in c-sb1.c to c-r4k.c lost this old hack
[MIPS] Hack for SB1 cache issues
Removing flush_icache_page a while ago broke SB1 which was using an empty
flush_data_cache_page function. This glues things well enough so a more
efficient but also more intrusive solution can be found later.
Signed-Off-By: Thiemo Seufer <ths@networkno.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
in the hope it was no longer needed. As it turns it still is so resurrect
it until there is a better solution.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
since we have this always turned on now and dont want it off (and hasnt been an option in a while)
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
move the init sections to the end of memory, so that after they
are free, run time memory is all continugous - this should help decrease
memory fragementation. When doing this, we also pack some of the other
sections a little closer together, to make sure we don't waste memory.
To make this happen, we need to rename the .data.init_task section to
.init_task.data, so it doesn't get picked up by the linker script glob.
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Oprofile needs to call intc_get_pending() in order to determine
whether a performance counter interrupt is pending.
Also, include the header which declares intc_get_pending() and fix the
definition to match the prototype.
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
There's a duplicate clock index between USART0 and USART1 which may be
causing system crashes when USART0 is used. Change the USART0 index
to '3', indicating the clock that is actually used by USART0.
Signed-off-by: Ben Nizette <ben@niasdigital.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
avr32 already sees the option from init/Kconfig.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
This patch extends the I/O resource to 0xfff000cf which will enable the
watchdog driver to access the reset cause (RCAUSE) register. Making it
capable of reporting boot status.
Signed-off-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/x86:
x86: enable "make ARCH=x86"
x86: do not use $(ARCH) when not needed
kconfig: use $K64BIT to set 64BIT with all*config targets
kconfig: add helper to set config symbol from environment variable
kconfig: factor out code in confdata.c
x86: move the rest of the menu's to Kconfig
x86: move all simple arch settings to Kconfig
x86: copy x86_64 specific Kconfig symbols to Kconfig.i386
x86: add X86_64 dependency to x86_64 specific symbols in Kconfig.x86_64
x86: add X86_32 dependency to i386 specific symbols in Kconfig.i386
x86: arch/x86/Kconfig.cpu unification
x86: start unification of arch/x86/Kconfig.*
x86: unification of cfufreq/Kconfig
Scrap the local __INLINE__ macro, and rename timeval_cmp to fasttime_cmp.
Inline macro was completely unnecessary since the macro was defined
locally to be inline.
timeval_cmp was inaccurately named since it does comparison on
struct fasttimer_t and not on struct timeval.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add \n\ at end of lines inside asm statement to avoid warning.
No change except adding \n\ to end of line and correcting
whitespace has been done.
Removes warning about multi-line string literals when compiling
arch/cris/arch-v10/lib/memset.c
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add \n\ at end of lines inside asm statement to avoid warning.
No change except adding \n\ to end of line and correcting
whitespace has been done.
Removes warning about multi-line string literals when compiling
arch/cris/arch-v10/lib/string.c
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Removes warning when compiling arch/cris/arch-v10/lib/usercopy.c
No change except adding \n\ on the end of the lines has been done.
Removes warning about multi-line string literals.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
These are needed due to a cache bug, and can be used to make sure that the
DMA descriptors are flushed to memory and can be safely handled by DMA.
flush_dma_descr - Flush one DMA descriptor.
flush_dma_list - Flush a complete list of DMA descriptors.
cris_flush_cache - Flush the complete cache.
cris_flush_cache_range - Flush only the specified range
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Improve and bugfix CRIS v10 fast timers.
- irq_handler_t now only takes two arguments.
- Keep interrupts disabled as long as we have a reference to the
fasttimer list and only enable them while doing the callback.
del_fast_timer may be called from other interrupt context.
- Fix bug where debug code could return without calling local_irq_restore.
- Use jiffies instead of usec (change from struct timeval to fasttime_t).
- Don't initialize static variables to zero.
- Remove obsolete #ifndef DECLARE_WAITQUEUE code.
- fast_timer_init should be __initcall.
- Change status/debug variables to unsigned.
- Remove CVS log and CVS id.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix timer interrupt parameters for CRIS v10.
- irq_handler_t only takes two arguments, use get_irq_regs to get
regs for profiling.
- Call update_process_times.
- Remove CVS tag.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove MTD_AMDSTD and MTD_OBSOLETE_CHIPS from defconfig, Kconfig and code,
instead we'll use MTD_CFI or MTD_JEDECPROBE.
[akpm@linux-foundation.org: codingl-style cleanups]
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I'm converting most array size calculations under arch/ to use
ARRAY_SIZE(). This is the patch for CRIS.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some unused config lines, and add some others that needs to be off
for a succesful compile. This is the minimal set of changes for 2.6.23.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Include linux/param.h for HZ.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Remove debug print.
- Change #if to #ifdef to avoid compile time warning if CONFIG_PROFILING
isn't set.
- Number of parameters to profile_tick has changed, drop the regs parameter.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corrects compile errors and the following:
- Remove oldset parameter from do_signal and do_notify_resume.
- Modified to fit new consolidated IRQ handling code.
- Reverse check order between external nmi and watchdog nmi to avoid false
watchdog oops in case of a glitch on the nmi pin.
- Return from an pin-generated NMI the same way as for other interrupts.
- Moved blocking of ethernet rx/tx irq from ethernet interrupt handler to
low-level asm interrupt handlers. Fixed in the multiple interrupt
handler also.
- Add space for thread local storage in thread_info struct.
- Add NO_DMA to Kconfig, and include arch specific Kconfig using arch
independent path. Include subsystem Kconfigs for pcmcia, usb, i2c,
rtc and pci.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix regression introduced with d435d862ba
("cpu hotplug: mce: fix cpu hotplug error handling").
A CPU which was not brought up during boot (using maxcpus and
additional_cpus parameters) couldn't be onlined anymore. For such a CPU it
seemed that MCE was not supported during CPU_UP_PREPARE-time which caused
mce_cpu_callback to return NOTIFY_BAD to notifier_call_chain. To fix this
we:
- call mce_create_device for CPU_ONLINE event (instead of CPU_UP_PREPARE),
- avoid mce_remove_device() for the CPU that is not correctly initialized
by mce_create_device() failure,
- make mce_cpu_callback always return NOTIFY_OK for CPU_ONLINE event.
Because CPU_ONLINE callback return value is always ignored.
[akinobu.mita@gmail.com: avoid mce_remove_device() for not initialized device]
[akinobu.mita@gmail.com: make mce_cpu_callback always return NOTIFY_OK]
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Marin Mitov points out that delay_tsc() can misbehave if it is preempted and
rescheduled on a different CPU which has a skewed TSC. Fix it by disabling
preemption.
(I assume that the worst-case behaviour here is a stall of 2^32 cycles)
Cc: Andi Kleen <ak@suse.de>
Cc: Marin Mitov <mitov@issp.bas.bg>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Handle the case of CONFIG_PRINTK being disabled. This requires a do-nothing
stub to be present in arch/um/include/user.h so that we don't get references
to printk from libc code.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make UML build in the absence of CONFIG_INET by making the inetaddr_notifier
registration depend on it.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
asm/page.h is disappearing from the libc headers and we don't need it anyway.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The spurious IRQ testing in request_irq is mishandled in um_request_irq, which
sets the incoming file descriptors non-blocking only after request_irq
succeeds. This results in the spurious irq calling read on a blocking
descriptor, and a hang.
Fixed by reversing the O_NONBLOCK setting and the request_irq call.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
i386 and x86-64 registers System RAM as IORESOURCE_MEM | IORESOURCE_BUSY.
But ia64 registers it as IORESOURCE_MEM only.
In addition, memory hotplug code registers new memory as IORESOURCE_MEM too.
This difference causes a failure of memory unplug of x86-64. This patch
fixes it.
This patch adds IORESOURCE_BUSY to avoid potential overlap mapping by PCI
device.
Signed-off-by: Yasunori Goto <y-goto@jp.fujitsu.com>
Signed-off-by: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Luck, Tony" <tony.luck@intel.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Stupid bug - we need to compare the return value of recvmsg to the value of
iov_len, not its size. This caused port_helper processes not to be killed on
shutdown on x86_64 because the pids weren't being passed out properly.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
symlinks to directories in the non-O= case were lacking -n, which meant
that, when the link already existed, a new link pointing at itself was
created in the target directory.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://lm-sensors.org/kernel/mhoffman/hwmon-2.6:
hwmon: (i5k_amb) Convert macros to C functions
hwmon: (w83781d) Add missing curly braces
hwmon: (abituguru3) Identify ABit IP35 Pro as such
hwmon: (f75375s) pwmX_mode sysfs files writable for f75375 variant
hwmon: (f75375s) On n2100 systems, set fans to full speed on boot
hwmon: (f75375s) Allow setting up fans with platform_data
hwmon: (f75375s) Add new style bindings
hwmon: (lm70) Convert semaphore to mutex
hwmon: (applesmc) Add support for Mac Pro 2 x Quad-Core
hwmon: (abituguru3) Add support for 2 new motherboards
hwmon: (ibmpex) Change printk to dev_{info,err} macros
hwmon: (i5k_amb) New memory temperature sensor driver
hwmon: (f75375s) fix pwm mode setting
hwmon: (ibmpex.c) fix NULL dereference
hwmon: (sis5595) Split sis5595_attributes_opt
hwmon: (sis5595) Add individual alarm files
hwmon: (w83627hf) push nr+1 offset into *_REG_FAN macros and simplify
hwmon: (w83627hf) hoist nr-1 offset out of show-store-temp-X
hwmon: Add power meter spec to Documentation/hwmon/sysfs-interface
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[POWERPC] Silence an annoying boot message
[POWERPC] Fix early btext debug on PowerMac
[POWERPC] Demote clockevent printk to KERN_DEBUG
[POWERPC] Fix CONFIG_SMP=n build error on ppc64
[POWERPC] Avoid unpaired stwcx. on some processors
[POWERPC] Fix oops related to 4xx flush_tlb_page modification
[POWERPC] cpm: Fix a couple minor issues in cpm_common.c.
[POWERPC] Add -mno-spe for ARCH=powerpc builds
vmemmap_populate will printk (with KERN_WARNING) for a lot of pages
if CONFIG_SPARSEMEM_VMEMMAP is enabled (at least it does on iSeries).
Use pr_debug for it instead.
Replace the only other use of DBG in this file with pr_debug as well.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The early btext debug wouldn't work on PowerMac when booted from BootX
due to the code looking for the wrong property name.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These don't need to be seen by everyone on every boot.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch "KVM: fix !SMP build error" change the way smp_call_function()
actually uses the passed in function names on non-SMP builds. So
previously it was never caught that the function passed in was never
actually defined.
This causes a build error on ppc64_defconfig + CONFIG_SMP=n:
arch/powerpc/mm/tlb_64.c: In function 'pgtable_free_now':
arch/powerpc/mm/tlb_64.c:71: error: 'pte_free_smp_sync' undeclared (first use in this function)
arch/powerpc/mm/tlb_64.c:71: error: (Each undeclared identifier is reported only once
arch/powerpc/mm/tlb_64.c:71: error: for each function it appears in.)
So we need to define it even if CONFIG_SMP is off. Either that or ifdef
out the smp_call_function() call, but that's ugly.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The context switch code in the kernel issues a dummy stwcx. to clear the
reservation, as recommended by the architecture. However, some processors
can have issues if this stwcx to address A occurs while the reservation
is already held to a different address B. To avoid this problem, the dummy
stwcx. needs to be paired with a dummy lwarx to the same address.
This adds the dummy lwarx, and creates a cpu feature bit to indicate
which cpus are affected. Tested on mpc8641_hpcn_defconfig in
arch/powerpc; build tested in arch/ppc.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
After unification of the Kconfig files and
introducing K64BIT support in kconfig
it required only trivial changes to enable
"make ARCH=x86".
With this patch you can build for x86_64 in several ways:
1) make ARCH=x86_64
2) make ARCH=x86 K64BIT=y
3) make ARCH=x86 menuconfig
=> select 64-bit
Likewise for i386 with the addition that
i386 is default is you say ARCH=x86.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
For x86 ARCH may say i386 or x86_64 and soon x86.
Rely on CONFIG_X64_32 to select between 32/64 or just
hardcode the value as appropriate.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
With this patch we have all the Kconfig file shared
between i386 and x86_64.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Most of the arch settings were equal so combine them
in the first part of Kconfig.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
No functional changes.
A prepatory step towards full unification.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_64 dependencies to all x86_64 specific symbols.
This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
To ease unification of Kconfig.i386 and Kconfig.x86_64
add X86_32 dependencies to all i386 specific symbols.
This patch introduce no functional changes but is one step
towards unification. This smaller step is used to ease
review of the patch set.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Move all CPU definitions to Kconfig.cpu
Always define X86_MINIMUM_CPU_FAMILY and do the
obvious code cleanup in boot/cpucheck.c
Comments from: Adrian Bunk <bunk@kernel.org> incorporated.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Brian Gerst <bgerst@didntduck.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
This step introduces the file arch/x86/Kconfig
which contains all the menu's from "Power Management"
and below.
The main part of the new Kconfig file is shared
and the remaining i386/x86_64 specific symbols
are covered by dependencies.
A x86_64 allmodconfig build did not show any differences.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Merge the two Kconfig files to a single file.
Checked using make allmodconfig for x86_64.
No changes in build.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Adrian Bunk <bunk@kernel.org>
Cc: Dave Jones <davej@codemonkey.org.uk>
restore sigcontext is taking a DNA exception while restoring FP context
from the user stack, during the sigreturn. Appended patch fixes it by
doing clts() if the app doesn't touch FP during the signal handler
execution. This will stop generating a DNA, during the fxrstor in the
sigreturn.
This improves 64-bit lat_sig numbers by ~30% on my core2 platform.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove some sort of bloaty code, try to get these pin_req arrays built at compile-time
- move this static things to the blackfin board file
- add pin_req array to struct bfin5xx_spi_master
- tested on BF537/BF548 with SPI flash
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
We currently do not. Also make it easier to handle cplb violations - in traps.c
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
remap_pfn_range() takes care of setting the appropriate VM_*
flags itself; there's no need for callers of remap_pfn_range()
to set VM_RESERVED before it is called.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
[ jdike - Pushing Chuck's patch - see
http://lkml.org/lkml/2005/9/16/261 for some history and a test
program. UML is also broken without this patch - its processes get
SIGBUS from the corrupt 6th argument to mmap being interpretted as a
file offset ]
When the 32-bit vDSO is used to make a system call, the %ebp register for
the 6th syscall arg has to be loaded from the user stack (where it's pushed
by the vDSO user code). The native i386 kernel always does this before
stopping for syscall tracing, so %ebp can be seen and modified via ptrace
to access the 6th syscall argument. The x86-64 kernel fails to do this,
presenting the stack address to ptrace instead. This makes the %rbp value
seen by 64-bit ptrace of a 32-bit process, and the %ebp value seen by a
32-bit caller of ptrace, both differ from the native i386 behavior.
This patch fixes the problem by putting the word loaded from the user stack
into %rbp before calling syscall_trace_enter, and reloading the 6th syscall
argument from there afterwards (so ptrace can change it). This makes the
behavior match that of i386 kernels.
Original-Patch-By: Roland McGrath <roland@redhat.com>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The addr argument to PTRACE_GET_THREAD_AREA and PTRACE_SET_THREAD_AREA is
not a magic constant. It's derived from the segment register values being
used, which are computed originally from the index used with set_thread_area.
The value does not need to match what a native i386 kernel would accept.
It needs to match the segment selectors that can actually be in use in this
32-bit process. The 64-bit ptrace support for PTRACE_GET_THREAD_AREA
(normally used only on 32-bit processes) is correct, but the 32-bit emulation
of ptrace is broken.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] IOSAPIC bogus error cleanup
[IA64] Update printing of feature set bits
[IA64] Fix IOSAPIC delivery mode setting
[IA64] XPC heartbeat timer function must run on CPU 0
[IA64] Clean up /proc/interrupts output
[IA64] Disable/re-enable CPE interrupts on Altix
[IA64] Clean-up McKinley Errata message
[IA64] Add gate.lds to list of files ignored by Git
[IA64] Fix section mismatch in contig.c version of per_cpu_init()
[IA64] Wrong args to memset in efi_gettimeofday()
[IA64] Remove duplicate includes from ia32priv.h
[IA64] fix number of bytes zeroed by sys_fw_init() in arch/ia64/hp/sim/boot/fw-emu.c
[IA64] Fix perfmon sysctl directory modes
* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6: (26 commits)
sh: remove dead config symbols from SH code
sh: Kill off broken snapgear ds1302 code.
sh: Add a dummy vga.h.
rtc: rtc-sh: Zero out tm value for invalid rtc states.
rtc: sh-rtc: Handle rtc_device_register() failure properly.
sh: Fix heartbeart on Solution Engine series
sh: Remove SCI_NPORTS from sh-sci.h
sh: Fix up PAGE_KERNEL_PCC() for nommu.
sh: hs7751rvoip: Kill off dead IPR IRQ mappings.
sh: hs7751rvoip: irq.c needs linux/interrupt.h.
sh: Kill off __{copy,clear}_user_page().
sh: Optimized copy_{to,from}_user_page() for SH-4.
sh: Wire up clear_user_highpage().
sh: Kill off the remaining ST40 cruft.
superhyway: Handle device_register() retval properly.
sh: kgdb sysrq depends on magic sysrq.
sh: Add -Werror for clean directories.
sh: Fix up kgdb build with modular sh-sci.
sh: Export __{s,u}divsi3_i4i on all CPUs.
sh: Fix up kgdb-on-NMI branch target.
...
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc: (37 commits)
[POWERPC] EEH: Make sure warning message is printed
[POWERPC] Make altivec code in swsusp_32.S depend on CONFIG_ALTIVEC
[POWERPC] windfarm: Fix windfarm thread freezer interaction
[POWERPC] Fix si_addr value on low level hash failures
[POWERPC] Refresh ppc64_defconfig and enable pasemi-related options
[POWERPC] pasemi: Update defconfig
[POWERPC] iSeries: Fix ref counting in vio setup
[POWERPC] ] Fix memset size error
[POWERPC] Fix link errors for allyesconfig
[POWERPC] iSeries_init_IRQ non-PCI tidy
[POWERPC] Change fallocate to match unistd.h on powerpc
[POWERPC] EEH: Avoid crash on null device
[POWERPC] EEH: Drivers that need reset trump others
[POWERPC] EEH: Clean up comments
[POWERPC] Fix off-by-one error in setting decrementer on Book E/4xx (v2)
[POWERPC] Fix switch_slb handling of 1T ESID values
[POWERPC] Fix build failure when CONFIG_VIRT_CPU_ACCOUNTING is not defined
[POWERPC] Include udbg.h when using udbg_printf
[POWERPC] Fix cache line vs. block size confusion
[POWERPC] Fix sysctl table check failure on PowerMac
...
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Use "is_power_of_2" macro for simplicity.
[SPARC]: Remove duplicate includes.
Remove the section annotation on FRV's free_initmem(). It can't be marked
__init, lest it free itself.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
prepare for up_smp_call_function() to ensure that the 'func'
pointer is unused. (which is related to a KVM build fix)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since powerpc started using CONFIG_GENERIC_CLOCKEVENTS, the
deterministic CPU accounting (CONFIG_VIRT_CPU_ACCOUNTING) has been
broken on powerpc, because we end up counting user time twice: once in
timer_interrupt() and once in update_process_times().
This fixes the problem by pulling the code in update_process_times
that updates utime and stime into a separate function called
account_process_tick. If CONFIG_VIRT_CPU_ACCOUNTING is not defined,
there is a version of account_process_tick in kernel/timer.c that
simply accounts a whole tick to either utime or stime as before. If
CONFIG_VIRT_CPU_ACCOUNTING is defined, then arch code gets to
implement account_process_tick.
This also lets us simplify the s390 code a bit; it means that the s390
timer interrupt can now call update_process_times even when
CONFIG_VIRT_CPU_ACCOUNTING is turned on, and can just implement a
suitable account_process_tick().
account_process_tick() now takes the task_struct * as an argument.
Tested both with and without CONFIG_VIRT_CPU_ACCOUNTING.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Altix (sn2) machines the "Error parsing MADT" message is
misleading because the lack of IOSAPIC entries is expected.
Since I am sure someone will ask, I have been told that
the chance of this changing anytime soon is close to nil.
Signed-off-by: George Beshers <gbeshers@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Newer Itanium versions have added additional processor feature set
bits. This patch prints all the implemented feature set bits. Some
bit descriptions have not been made public. For those bits, a generic
"Feature set X bit Y" message is printed. Bits that are not implemented
will no longer be printed.
Signed-off-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that redirect hit bit in I/O SAPIC RTE is set even
when it must be disabled (e.g. nointroute boot option is set, CPU
hotplug is enabled or percpu vector is enabled).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Currently, XPC's heartbeat timer function runs on whatever CPU modprobe/insmod
ran on when XPC was started. To avoid the heartbeat from being delayed for
long periods the timer function must run on CPU 0.
N.B. Altix doesn't currently allow cpu0 to be taken offline, so this is
safe for now. This code must be revised when offline of cpu0 is enabled.
Signed-off-by: Dean Nelson <dcn@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
A debugging printk is removed, and a comment is fixed to match
the code.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Newer GCC's are capable of autovectorization for ISA extensions like
AltiVec and SPE. If we happen to build with one of those compilers we
will get SPE instructions in random kernel code. Today we only allow
basic interger code in the kernel and FP, AltiVec, or SPE in special
explicit locations that have handled the proper saving and restoring of
the register state (since on uniprocessor we lazy context switch the
register state for FP, AltiVec, and SPE).
-mno-spe disables the compiler for automatically generating SPE
instructions without our knowledge.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
One-shot timer mode on PXA has various bugs which prevent kernels
build with NO_HZ enabled booting. They end up spinning on a
permanently asserted timer interrupt because we don't properly
clear it down - clearing the OIER bit does not stop the pending
interrupt status. Fix this in the set_mode handler as well.
Moreover, the code which sets the next expiry point may race with
the hardware, and we might not set the match register sufficiently
in the future. If we encounter that situation, return -ETIME so
the generic time code retries.
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On thecus n2100, the bootloader does not setup fans to run. In order
to protect the user from frying their gear, start up fans on boot.
Signed-off-by: Riku Voipio <riku.voipio@movial.fi>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Fix old buglet; a warning message should have been printed
when a hardware reset takes too long.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the altivec code in swsusp_32.S depend on CONFIG_ALTIVEC to
avoid build failures for systems that don't have altivec. I'm not sure
whether the code will actually work for other systems, but it was merged
for just ppc32 rather than powermac a very long time ago.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If the low level MMU hash table insertion returns an error (which
can happen in some rare circumstances when the hypervisor refuses
the insertion of a PTE, typically if you try to access junk via
/dev/mem), the generated signal had an incorrect si_addr value due
to a bug in the assembly, which was loading it as a 32 bits quantity
instead of a 64 bits quantity.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Refresh ppc64_defconfig, add PPC_PASEMI and various options that the
common boards there need:
* Chip drivers (iommu, ethernet, IDE, CF, EDAC, MDIO/PHY)
* PCMCIA
* PATA_PCMCIA
* RTC_CLASS
* SATA_MV
* SATA_SIL24
* IP_PNP + NFS_ROOT for diskless booting
+ possibly some other things I might have missed to list
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update pasemi_defconfig. Add a few missing options for default devices
on electra boards, enable tickless and hrtimers, etc, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The size passing to memset is wrong.
Signed-off-by Li Zefan <lizf@cn.fujitsu.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
An allyesconfig build creates a .text section that is so big that the
.text.init.refok and .fixup sections are too far away for the relocations
to be fixed up correctly. This patch fixes that by linking all the
relevent text sections for each file together.
Suggested by Paul Mackerras.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
ppc_md.init_IRQ is not called if it is NULL, so we don't need an empty
routine in the non PCI case.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Bugfix: avoid crash if there's no PCI device for a given
openfirmware node.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Bugfix: if a driver controlling one part of a multi-function PCI card
has asked for a reset, honor that request above all others.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The decrementer in Book E and 4xx processors interrupts on the
transition from 1 to 0, rather than on the 0 to -1 transition as on
64-bit server and 32-bit "classic" (6xx/7xx/7xxx) processors. At the
moment we subtract 1 from the count of how many decrementer ticks are
required before the next interrupt before putting it into the
decrementer, which is correct for server/classic processors, but could
possibly cause the interrupt to happen too early on Book E and 4xx if
the timebase/decrementer frequency is low.
This fixes the problem by making set_dec subtract 1 from the count for
server and classic processors, instead of having the callers subtract
1. Since set_dec already had a bunch of ifdefs to handle different
processor types, there is no net increase in ugliness. :)
Note that calling set_dec(0) may not generate an interrupt on some
processors. To make sure that decrementer_set_next_event always calls
set_dec with an interval of at least 1 tick, we set min_delta_ns of
the decrementer_clockevent to correspond to 2 ticks (2 rather than 1
to compensate for truncations in the conversions between ticks and
ns).
This also removes a redundant call to set the decrementer to
0x7fffffff - it was already set to that earlier in timer_interrupt.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we have 1TB segment size support, we need to be using the
GET_ESID_1T macro when comparing ESID values for pc, stack, and
unmapped_base within switch_slb(). A new helper function called
esids_match() contains the logic for deciding when to call GET_ESID
and GET_ESID_1T.
This fixes a duplicate-slb-entry inspired machine-check exception I
was seeing when trying to run java on a power6 partition.
Tested on power6 and power5.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Without this patch I get the following build failure
CC arch/powerpc/platforms/celleb/setup.o
arch/powerpc/platforms/celleb/setup.c:151: error: 'generic_calibrate_decr' undeclared here (not in a function)
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the error
error: implicit declaration of function "udbg_printf"
We have a few spots where we reference udbg_printf() without #including
udbg.h. These are within #ifdef DEBUG blocks, so unnoticed until we do
a #define DEBUG or #define DEBUG_LOW nearby.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We had an historical confusion in the kernel between cache line
and cache block size. The former is an implementation detail of
the L1 cache which can be useful for performance optimisations,
the later is the actual size on which the cache control
instructions operate, which can be different.
For some reason, we had a weird hack reading the right property
on powermac and the wrong one on any other 64 bits (32 bits is
unaffected as it only uses the cputable for cache block size
infos at this stage).
This fixes the booting-without-of.txt documentation to mention
the right properties, and fixes the 64 bits initialization code
to look for the block size first, with a fallback to the line
size if the property is missing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix two build errors on powerpc allyesconfig + CONFIG_SMP=n:
arch/powerpc/platforms/built-in.o: In function `cpu_affinity_set':
arch/powerpc/platforms/cell/spu_priv1_mmio.c:78: undefined reference to `.iic_get_target_id'
arch/powerpc/platforms/built-in.o: In function `iic_init_IRQ':
arch/powerpc/platforms/cell/interrupt.c:397: undefined reference to `.iic_setup_cpu'
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The ps3 target produces two images, and the binary one is not the
"primary" image that corresponds to the -o flag; thus, it no longer
uses the generic binary flag.
On platforms which do use the binary flag, it no longer produces a
.bin suffix, so that the output file matches what was passed to the -o flag.
This should fix the zImage ln problems for the ps3 target.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Acked-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit 91a69029 introduced an additional parameter to the .read and .write
methods for sysfs binary attributes. Two mv64x60_pci functions
were missed in that patch, resulting in these errors:
/cache/git/linux-2.6/arch/powerpc/sysdev/mv64x60_pci.c:77: warning: initialization from incompatible pointer type
/cache/git/linux-2.6/arch/powerpc/sysdev/mv64x60_pci.c:78: warning: initialization from incompatible pointer type
Add the missing "struct bin_attribute *" parameter.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since commit 76d2160147, the NE2000 card
is not working anymore on PPC and POWERPC and produces WATCHDOG
timeouts.
The patch below fixes that the same way it has been done on x86, x86_64
and MIPS.
Signed-off-by: Aurelien Jarno <aurelien@aurel32.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There are plans afoot to use pci_restore_msi_state() to restore MSI
state after a device reset. In order for this to work for the RTAS MSI
backend, we need to read back the MSI message from config space after
it has been setup by firmware.
This should be sufficient for restoring the MSI state after a device
reset, however we will need to revisit this for suspend to disk if that
is ever implemented on pseries.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix build break and warnings in current mainline git:
arch/ppc/syslib/m8260_setup.c: In function 'm8260_setup_arch':
arch/ppc/syslib/m8260_setup.c:63: error: implicit declaration of function 'identify_ppc_sys_by_name_and_id'
arch/ppc/syslib/m8260_setup.c:64: warning: passing argument 1 of 'in_be32' makes pointer from integer without a cast
arch/ppc/syslib/m8260_setup.c: In function 'm8260_show_cpuinfo':
arch/ppc/syslib/m8260_setup.c:158: warning: format '%08x' expects type 'unsigned int', but argument 5 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%d' expects type 'int', but argument 6 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%u' expects type 'unsigned int', but argument 7 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%u' expects type 'unsigned int', but argument 8 has type 'long unsigned int'
arch/ppc/syslib/m8260_setup.c:158: warning: format '%u' expects type 'unsigned int', but argument 9 has type 'long unsigned int'
make[1]: *** [arch/ppc/syslib/m8260_setup.o] Error 1
make[1]: *** Waiting for unfinished jobs....
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This will force the snapgear boards to use the on-chip SH RTC instead,
until the rtc-ds1302 driver is merged. The current code is broken
and hasn't built in some time, so just kill it off and get the board
working again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Access size to LED is not added on Solution Engine series.
LED doesn't work. Fixed this problem.
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that copy_to_user_page()/copy_from_user_page() are wired up, we
can drop the old __copy_xxx() implementations. Now that the page
colouring scheme has changed via kmap_coherent(), we can avoid the
flush in these specific helpers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This moves copy_{to,from}_user_page() out-of-line on SH-4 and
converts for the kmap_coherent() API. Based on the MIPS
implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the kmap_coherent() API in place, this is trivial to implement,
and lets us avoid the cache flush in certain cases.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The ST40 stuff in-tree hasn't built for some time, and hasn't been
updated for over 3 years. ST maintains their own out-of-tree changes
and rebases occasionally, and that's ultimately where all of the ST40
users go anyways.
In order for the ST40 code to be brought up to date most of the stuff
removed in this changeset would have to be rewritten anyways, so there's
very little benefit in keeping the remnants around either.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Currently these are only being exported for CONFIG_CPU_SH4. This
invariably breaks when building for an SH-3 that includes multiple
targets in multilib.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was all reworked some time ago, the old debug_enter was ripped
out with everything going through a debug trap jump table instead.
Kill off the debug_enter target and reference kgdb_handle_exception
directly.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-4A parts generally don't have any use for this, and it requires an
alternate implementation anyways. Leave this as an SH-4 only option,
as that's the only place this has been needed in the past.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When uImage is made by using 'make uImage', zImage is used.
If zImage is used, the compression method need not be set.
However, it is set for "gzip" for a compression method.
I corrected to set "none".
Signed-off-by: Nobuhiro Iwamatsu <iwamatsu@nigauri.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Clean up /proc/interrupts output on the system that has 10 or more
CPUs.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When the CPE handler encounters too many CPEs (such as a solid single
bit memory error), it sets up a polling timer and disables the CPE
interrupt (to avoid excessive overhead logging the stream of single
bit errors). disable_irq_nosync() calls chip->disable() to provide
a chipset specifiec interface for disabling the interrupt. This patch
adds the Altix specific support to disable and re-enable the CPE interrupt.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
No need to print "McKinley Errata 9 workaround not needed; disabling it"
on every non-McKinley Itanium, which at this point is almost all of them.
Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: Tony Luck <tony.luck@intel.com>
If you build the kernel `in-place' then do a git update, git
complains about arch/ia64/kernel/gate.lds being modified and
untracked.
Add that (generated) file to a .gitignore file.
Signed-off-by: Peter Chubb <peterc@gelato.unsw.edu.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
There is a section mismatch when building CONFIG_FLATMEM=y kernels
that also have CONFIG_HOTPLUG_CPU=y
WARNING: vmlinux.o(.text+0x5a902): Section mismatch: reference to \
.init.text:__alloc_bootmem (between 'per_cpu_init' and 'count_pages')
The issue occurs because per_cpu_init() in mm/contig.c is
marked __cpuinit (which is #define'd to nothing on a hot
plug cpu configuration) call __alloc_bootmem() (which is
an __init function). The usage is actually safe because
the __alloc_bootmem() is inside an "if (first_time)" test
so that the call is only made while it is still legal to
do so.
But the warning is irritating. Move the allocation to
find_memory().
Signed-off-by: Tony Luck <tony.luck@intel.com>
Reported by Al Viro.
This fixes it:
[AC]FLAGS -> KBUILD_[AC]FLAGS conversion in Makefile-i386.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Al Viro <viro@ftp.linux.org.uk>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Not sizeof(ptr) ... we meant to say sizeof(*ptr).
Also moved the memset to the error path (the normal path overwrites
every field in the structure anyway) -Tony
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The sizeof a pointer is constant, we want the sizeof what is pointed to.
Zero out 'sizeof(*efi_systab)' bytes of the efi_system_table_t pointer
'efi_systab' instead.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Tony Luck <tony.luck@intel.com>
New sanity checks in sysctl_check_table() complain about a couple
of mode 0755 that should be 0555 in the perfmon code:
sysctl table check failed: /kernel .1 Writable sysctl directory
sysctl table check failed: /kernel/perfmon Writable sysctl directory
Signed-off-by: Tony Luck <tony.luck@intel.com>
KERNEL_DEFINES needs whitespace trimmed, otherwise the whitespace crunching
done by make fools the patsubst which is used to remove KERNEL_DEFINES from
USER_CFLAGS.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix an incompatible-pointer warning.
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This fixes a section error on OMAP when the framebuffer is enabled.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git390.osdl.marist.edu/pub/scm/linux-2.6:
[S390] tod clock: announce clocksource as perfect
[S390] Rename "idle_time" attribute to "idle_time_us".
[S390] Fix priority mistakes in drivers/s390/cio/cmf.c
[S390] Fix memory detection.
[S390] Fix compile on !CONFIG_SMP.
[S390] device_schedule_callback() for dcssblk.
[S390] Fix smsgiucv init on no iucv machines
[S390] cio: use INIT_WORK to initialize struct work.
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-lguest:
lguest: tidy up documentation
kernel/futex.c: make 3 functions static
unexport access_process_vm
lguest: make async_hcall() static
With commit 5984a2fc7e kobject_name() is
correctly being used to access the name field of kobj, but that function
needs a pointer to a kobject, not the kobject itself.
Signed-off-by: Robert Schwebel <r.schwebel@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
After Adrian Bunk's "make async_hcall static" moved things around, update
comments to match (aka "make Guest").
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The Time of Day clock is the standard time source for s390. It is
- monotonic
- allows very fast reading
- architecture guarantees at least microsecond stepping
- available as part of the architecture
We should announce the rate of tod as 400 to be in sync with the
description found in clocksource.h:
"400-499:Perfect The ideal clocksource. A must-use where available."
This change will prefer tod over less reliable clock sources.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Seems that people prefer to have the unit encoded in the attribute
name. Also makes parsing easier.
Now we have:
# cat /sys/devices/system/cpu/cpu0/idle_time_us
131473592
instead of
# cat /sys/devices/system/cpu/cpu0/idle_time
131473592 us
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Yet another patch in the countless series of memory detection fixes:
if the last area of the reported storage size is a hole the detection
loop will loop forever.
Just break chunk detection loop if its end is going to be larger than
reported storage size.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Commit fae8b22d3e
"[S390] Add per-cpu idle time / idle count sysfs attributes" causes
a link error on !CONFIG_SMP.
Fix this by adding some #ifdef's. Real fix would be to cleanup the
code since we don't register a cpu on !CONFIG_SMP. But that would
be quite a big patch. For the time being this is good enough.
arch/s390/kernel/built-in.o: In function `do_monitor_call':
(.text+0x50d4): undefined reference to `per_cpu__s390_idle'
arch/s390/kernel/built-in.o: In function `cpu_idle':
(.text+0x518c): undefined reference to `per_cpu__s390_idle'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
In accordance with the newly formalized 32-bit boot protocol, set
%ebx == %ebp == %edi == 0 in order to support future extensions to the
protocol.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The Jazz machines have to use the PIT timer for dyntick and highresolution
kernels. This may break because currently just like i386 used to do MIPS
uses two separate spinlocks in the actual PIT code and the PC speaker
code. So switch to do it the same that x86 currently does PIT locking.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix ISA irq acknowledge.
Make r4030 clockevent code look like other mips clockevent code.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Register A20R clockevent.
Remove PIT timer setup because it doesn't work
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
arch/mips/au1000/pb1200/irqmap.c:101: warning: ignoring return value of 'request_irq', declared with attribute warn_unused_result
And while at it a few coding style cleanups.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* Do not include unnecessary headers.
* Do not mention time.README.
* Do not mention mips_timer_ack.
* Make clocksource_mips static. It is now dedicated to c0_timer.
* Initialize clocksource_mips.read statically.
* Remove null_hpt_read.
* Remove an argument of plat_timer_setup. It is just a placeholder.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This adds in the x3proto and magicpanelr2 mach types, plugs in
highlander and rts7751r2d groups, and also hooks up the r2d
subtypes.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
R7780RP can't do byte-sized accesses to CF, so needs to do word
sized access with low-byte masking. This same problem exists
on older versions of the R2D, with the same workaround having
been implemented in 43f4b8c757
there. Follow that change for the highlander boards.
This does not impact R7780MP or SH7785 based Highlander modules.
If you're unfortunate enough to be stuck with an R7780RP, this
patch is for you!
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
It's assumed that .eh_frame is terminated with 4-byte 0 in shared
libraries and executable. It seems to be the case for VDSOs too.
Without this terminator, I saw failures when unwinding from VDSO,
though I don't know how other architectures handle this issue.
For the normal libs, crtendS.o gives this terminator. We can use
such terminating objects. Or we can add a 4-byte 0 with modifying
the linker script like as the patch below.
Signed-off-by: Kaz Kojima <kkojima@rr.iij4u.or.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
While using separate IRQ stacks can cut down on stack consumption,
many users can also use 4k stacks directly without the additional
need of separate stacks for soft and hardirqs.
With this split, we support the same rationale for 4KSTACKS as
m68knommu, with the IRQSTACKS abstraction as per ppc64.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
movca.l is restricted to SH-4 and up only, though compilers that
are unable to support ISA tuning (especially older versions of
binutils) will happily compile in the bogus opcode on older parts.
Conditionalize it to fix SH-3 regressions noted by Kristoffer.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Re-order the EMAC interrupts in the walnut.dts file so that they are mapped
correctly.
Signed-off-by: Steve Falco <sfalco at harris.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
mmu_mapin_ram() loops over total_lowmem to setup page tables. However, if
total_lowmem is less that 16M, the subtraction rolls over and results in
a number just under 4G (because total_lowmem is an unsigned value).
This patch rejigs the loop from countup to countdown to eliminate the
bug.
Special thanks to Magnus Hjorth who wrote the original patch to fix this
bug. This patch improves on his by making the loop code simpler (which
also eliminates the possibility of another rollover at the high end)
and also applies the change to arch/powerpc.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
The 44x family has an interesting "feature" which is a virtually
tagged instruction cache (yuck !). So far, we haven't dealt with
it properly, which means we've been mostly lucky or people didn't
report the problems, unless people have been running custom patches
in their distro...
This is an attempt at fixing it properly. I chose to do it by
setting a global flag whenever we change a PTE that was previously
marked executable, and flush the entire instruction cache upon
return to user space when that happens.
This is a bit heavy handed, but it's hard to do more fine grained
flushes as the icbi instruction, on those processor, for some very
strange reasons (since the cache is virtually mapped) still requires
a valid TLB entry for reading in the target address space, which
isn't something I want to deal with.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
On 4xx CPUs, the current implementation of flush_tlb_page() uses
a low level _tlbie() assembly function that only works for the
current PID. Thus, invalidations caused by, for example, a COW
fault triggered by get_user_pages() from a different context will
not work properly, causing among other things, gdb breakpoints
to fail.
This patch adds a "pid" argument to _tlbie() on 4xx processors,
and uses it to flush entries in the right context. FSL BookE
also gets the argument but it seems they don't need it (their
tlbivax form ignores the PID when invalidating according to the
document I have).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Don't allocate hose2 when when hose1 can't be allocated and free hose1 when
hose2 can't be allocated.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
PowerPC 440EP(x) 440GR(x) processors have the same PVR values, since
they have identical cores. However, FPU is not supported on GR(x) and
enabling APU instruction broadcast in the CCR0 register (to enable FPU)
may cause unpredictable results. There's no safe way to detect FPU
support at runtime. This patch provides a workarund for the issue.
We use a POWER6 "logical PVR approach". First, we identify all EP(x)
and GR(x) processors as GR(x) ones (which is safe). Then we check
the device tree cpu path. If we have a EP(x) processor entry,
we call identify_cpu again with PVR | 0x8. This bit is always 0
in the real PVR. This way we enable FPU only for 440EP(x).
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Add the 'set -e' command to the wrapper script so that if any command
fails then the script will automatically exit
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Allow wrapper script to print verbose progress when the V is set in the
environment.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
We can't export verify_compat_iovec when CONFIG_NET is
disabled, and consequently the Solaris compat module
should also depend upon CONFIG_NET.
Signed-off-by: David S. Miller <davem@davemloft.net>
When CONFIG_BUG is turned off, the standard trick of:
switch (x) {
case X:
...
case Y:
...
default:
BUG();
};
to mark impossible cases does not work because BUG() evalutes
to nothing and thus GCC just sees a fallthrough code path.
Add an explicit KERN_ERR log message and a do_exit() to trap
this case.
Signed-off-by: David S. Miller <davem@davemloft.net>
It is unused since we went to an I-cache flush that solely used
the 'flush' instruction, and it's presence breaks the build
when PAGE_SIZE is 512KB.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix assignment instead of condition
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Resolve:
CC arch/arm/mach-pxa/time.o
arch/arm/mach-pxa/time.c: In function `pxa_osmr0_set_mode':
arch/arm/mach-pxa/time.c:154: warning: enumeration value `CLOCK_EVT_MODE_RESUME' not handled in switch
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Jon Eibertzon writes:
> We have noticed that the I-cache is disabled while waiting for
> interrupt in cpu_arm926_do_idle in arch/arm/mm/proc-arm926.S
> and we are curious to know why, because this causes us a great
> performance hit when executing in FIQ-handlers. Is it assumed
> here that every individual FIQ-handler re-enables the I-cache?
The I-cache disable is an errata workaround, so the solution is to
disable FIQs across the section with the I-cache disabled.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
CC arch/arm/mach-netx/xc.o
arch/arm/mach-netx/xc.c: In function 'request_xc':
arch/arm/mach-netx/xc.c:192: error: 'struct kobject' has no member named 'name'
arch/arm/mach-netx/xc.c:196: error: 'struct kobject' has no member named 'name'
arch/arm/mach-netx/xc.c:200: error: 'struct kobject' has no member named 'name'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix:
arch/arm/mach-omap1/built-in.o: In function `h2_init':
board-h2.c:(.init.text+0xbb4): undefined reference to `i2c_register_board_info'
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
CPU_HAS_SR_RB is selected by both CPU_SH3 and CPU_SH4, so having a
dependency and default y on those additionally doesn't make much sense.
The select also has to be special cased for CPUs that don't support
this.
This is also something that has been abused too much as a result
of being user-visible, hence the addition of the select in the first
place. So just kill the user-visibility entirely while we're at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Fix incorrect return value from ia64_setup_msi_irq()
[IA64] arch/ia64/sn/kernel/mca.c: undo lock when sn_oemdata can't be extended
[IA64] update sn2 defconfig to 64kb pages
[IA64] fix typo in per_cpu_offset
[IA64] /proc/cpuinfo "physical id" field cleanups
[IA64] vDSO vs --build-id
[IA64] check-segrel.lds vs --build-id
[IA64] vmcore_find_descriptor_size should be in __init
[IA64] ia64/mm/init.c: fix section mismatches
Fix the problem that pci_enable_msi() fails on ia64 platform. The cause of
this problem is incorrect return value of ia64_setup_msi_irq(). It must
return 0 on success, instead of irq number.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
Blackfin arch: use a less common define name in BF549
Blackfin arch: Add missing definitions for BF561
Blackfin arch: reclaim a few bytes from the end of our init section
Blackfin arch: fix libata data struct member from irq_type to irq_flags
Blackfin arch: Do not pollute name space used in linux-2.6.x/sound
Blackfin arch: Fix bug set correct baud for spi mmc and enable SPI after DMA.
Blackfin arch: update board defconfig files according to latest information from ADI datasheet
Blackfin arch: ensure that speculative loads of bad pointers don't cause us to do bad things.
Blackfin arch: Add missing definitions of BF54x
Blackfin arch: Fix random crash issue found by Michael.
Blackfin arch: fix bug: tell users if the kernel is recovering from a fault condition
Blackfin arch: add support for checking/clearing overruns in generic purpose Timer API
Blackfin arch: cleanup arch/blackfin/kernel/traps.c handling code.
Blackfin arch: Apply Bluetchnix vendor patch provided by Harald Krapfenbauer
Blackfin arch: fix bug BlueTechnix CM-BF537 board config uses wrong IRQ for net2272 driver
Blackfin arch: fix bug: kernel prints out error message twice
Blackfin arch: add NFC driver support in BF527-EZKIT board
Blackfin arch: Added support for HV Sistemas H8606 board
No reason I can think of of making them default y Most people don't have
the hardware and with default y they just pollute lots of configs during
make oldconfig.
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Jeff Garzik <jeff@garzik.org>
Acked-by: "Nelson, Shannon" <shannon.nelson@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Converts from the profile notifier to the timer hook. Follows
the generic timer interrupt-based change.
This really wants to be converted to perfmon..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some cleanups to the SH linker script. This reorders some of the
data sections for more optimal placement, general tabification,
and plugging in omitted generic definitions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When the SH kernel used to support embedding a ramdisk in the
pre-initramfs days it was placed in a special section and made to
look like a regular initrd. Since that was removed ages ago, kill
off the remaining cruft that was missed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
memory_end was being clobbered by whatever the kernel config had
specified, rather than obeying the setup option. Fix this up so
that memory_end is only initialized if nothing has been set on
the command line.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Changes:
1. The baud for spi mmc defined in board file is not used by the old
spi driver. A slower value from spi framework is used instead. In latest
bug fixing, the correct baud is use which is too high for spi MMC card.
2. SPI is enabled only after DMA is started.
3. MMC detection IRQ is set to 55.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Starting with binutils somewhere around 2.17.50.14 the vmlinux file
contains a ".note.gnu.build-id" section which doesn't get removed when
the zImage is built; resulting in a 2GB intermediate file and a broken
zImage.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
I'm converting most array size calculations under arch/ to use the
ARRAY_SIZE() macro. This is the (tiny) patch for sh.
Signed-off-by: Alejandro Martinez Ruiz <alex@flawedcode.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove reference to out of date/rotting websites.
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds support for the ax88796 driver on highlander boards.
Implemented using the 93cx6 EEPROM support introduced by commit-id
89e536a190.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
node0_bdata and paddr_to_nid() can become static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch removes the unused EXPORT_SYMBOL(machine_id).
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch renames the 4 symbols iommu_hole_init(), iommu_aperture,
iommu_aperture_allowed, iommu_aperture_disabled. All these symbols are only
used for the GART implementation of IOMMUs.
It adds and additional gart_ prefix to them.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes some functions and variables static in pci-gart_64.c which are
not used somewhere else.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch renames the IOMMU config option to GART_IOMMU because in fact it
means the GART and not general support for an IOMMU on x86.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch renames the include file asm-x86/iommu.h to asm-x86/gart.h to make
clear to which IOMMU implementation it belongs. The patch also adds "GART" to
the Kconfig line.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Additional CPUID strings (sse4_1, sse4_2, sse5, skinit, wdt); fix the
positioning of the AMD ecx strings (cr8_legacy was duplicated under
two different names, so the alignment of all the other strings were
off by one.)
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 2e1c49db4c.
First off, testing in Fedora has shown it to cause boot failures,
bisected down by Martin Ebourne, and reported by Dave Jobes. So the
commit will likely be reverted in the 2.6.23 stable kernels.
Secondly, in the 2.6.24 model, x86-64 has now grown support for
SPARSEMEM_VMEMMAP, which disables the relevant code anyway, so while the
bug is not visible any more, it's become invisible due to the code just
being irrelevant and no longer enabled on the only architecture that
this ever affected.
Reported-by: Dave Jones <davej@redhat.com>
Tested-by: Martin Ebourne <fedora@ebourne.me.uk>
Cc: Zou Nan hai <nanhai.zou@intel.com>
Cc: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When GDB writes a breakpoint into address area of inferior process the
kernel needs to invalidate the modified memory in the inferior which
is done by calling flush_cache_page which in turns calls
r4k_flush_cache_page and local_r4k_flush_cache_page for VSMP or SMTC
kernel via r4k_on_each_cpu().
As the VSMP and SMTC SMP kernels for 34K are running on a single shared
caches it is possible to get away without interprocessor function calls.
This optimization is implemented in r4k_on_each_cpu, so
local_r4k_flush_cache_page is only ever called on the local CPU.
This is where the following code in local_r4k_flush_cache_page() strikes:
/*
* If ownes no valid ASID yet, cannot possibly have gotten
* this page into the cache.
*/
if (cpu_context(smp_processor_id(), mm) == 0)
return;
On VSMP and SMTC had a function of cpu_context() for each CPU(TC).
So in case another CPU than the CPU executing local_r4k_cache_flush_page
has not accessed the mm but one of the other CPUs has there may be data
to be flushed in the cache yet local_r4k_cache_flush_page will falsely
return leaving the I-cache inconsistent for the breakpoint.
While the issue was discovered with GDB it also exists in
local_r4k_flush_cache_range() and local_r4k_flush_cache().
Fixed by introducing a new function has_valid_asid which on MT kernels
returns true if a mm is active on any processor in the system.
This is relativly expensive since for memory acccesses in that loop
cache misses have to be assumed but it seems the most viable solution
for 2.6.23 and older -stable kernels.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Enable the onboard GenBus IDE interface in the default configuration.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Contrary to the belief of some, the R3000 and related processors did have
caches, both a data and an instruction cache. Here is an implementation
of r3k_flush_cache_page(), which is the processor-specific back-end for
flush_cache_range(), done according to the spec in
Documentation/cachetlb.txt.
While at it, remove an unused local function: get_phys_page(), do some
trivial formatting fixes and modernise debugging facilities.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A comment on ptrace_getregs() states "Registers are sign extended to
fill the available space." but it is not true. Fix code to match the
comment. Also fix casts on each caller to get rid of some warnings.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch separates the platform devices registration for the MTX-1
specific devices: GPIO leds and watchdog.
[Minor fixup and formatting change -- Ralf]
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Mmap with MAP_FIXED was not validating the addr and len parameters. This
leads to the failure of GCC's gcc.c-torture/execute/loop-2[fg].c testcases
when using the o32 ABI on a 64 bit kernel.
These testcases try to mmap 65536 bytes at 0x7fff8000 and then access all
the memory. In 2.6.18 and 2.6.23.1 (and likely other versions as well)
the kernel maps the requested memory, but since half of it is above
0x80000000 a SIGBUS is generated when it is accessed.
This patch moves the len validation above the MAP_FIXED processing so that
it is always validated. It also adds validation to the addr parameter for
MAP_FIXED mappings.
Signed-off-by: David Daney <ddaney@avtrex.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Try increasingly longer time periods starting of at 0x10 cycles. This
should be fast on hardware and work nicely with emulators.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The expression "(long)(read_c0_count() - cnt)" can never be a negative
value on 64-bit kernel. Cast to "int" before comparison.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
They break the timer interrupt initialization and only seem to be a kludge
for initialization happening in the wrong order. Further testing done by
Thiemo confirms the suspicion that the other invocations also seem to have
useless.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Convert jmr3927_clock_event_device to more generic
txx9tmr_clock_event_device which supports one-shot mode. The
txx9tmr_clock_event_device can be used for TX49 too if the cp0 timer
interrupt was not available.
Convert jmr3927_hpt_read to txx9_clocksource driver which does not
depends jiffies anymore. The txx9_clocksource itself can be used for
TX49, but normally TX49 uses higher precision clocksource_mips.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Fixme: At the time of this writing cevt-r4k.c doesn't yet know about how
to handle the alternate timer interrupt of the RM9000.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since the cp0 compare interrupt handler isn't initialized by the time
plat_time_init is called don't set IE_IRQ5 anymore, cevt-r4k.c will do
that a little later itself.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The old plat_timer_setup hook is no longer getting called so the Alchemy
time initialization was getting skipped.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
clockevent_delta2ns() use the shift and mult value, so
clockevent_set_clock() should be called first.
Pointed out by Atsushi Nemoto.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
