do a proper idle-wakeup event on HLT as well - some CPUs stop the TSC
in HLT too, not just when going through the ACPI methods.
(the ACPI idle code already does this.)
[ update the 64-bit side too, as noticed by Jiri Slaby. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
scale the sched_clock() cyc_2_nsec scaling factor according to
CPU frequency changes.
[ mingo@elte.hu: simplified it and fixed it for SMP. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
cf http://lkml.org/lkml/2007/10/3/41
To summarize: on Linux, SA_ONSTACK decides whether you are already on the
signal stack based on the value of the SP at the time of a signal. If
you are not already inside the range, you are not "on the signal stack"
and so the new signal handler frame starts over at the base of the signal
stack.
sigaltstack (and sigstack before it) was invented in BSD. There, the
SA_ONSTACK behavior has always been different. It uses a kernel state
flag to decide, rather than the SP value. When you first take an
SA_ONSTACK signal and switch to the alternate signal stack, it sets the
SS_ONSTACK flag in the thread's sigaltstack state in the kernel.
Thereafter you are "on the signal stack" and don't switch SP before
pushing a handler frame no matter what the SP value is. Only when you
sigreturn from the original handler context do you clear the SS_ONSTACK
flag so that a new handler frame will start over at the base of the
alternate signal stack.
The undesireable effect of the Linux behavior is that an overflow of the
alternate signal stack can not only go undetected, but lead to a ring
buffer effect of clobbering the original handler frame at the base of the
signal stack for each successive signal that comes just after the
overflow. This is what Shi Weihua's test case demonstrates. Normally
this does not come up because of the signal mask, but the test case uses
SA_NODEFER for its SIGSEGV handler.
The other subtle part of the existing Linux semantics is that a simple
longjmp out of a signal handler serves to take you off the signal stack
in a safe and reliable fashion without having used sigreturn (nor having
just returned from the handler normally, which means the same). After
the longjmp (or even informal stack switching not via any proper libc or
kernel interface), the alternate signal stack stands ready to be used
again.
A paranoid program would allocate a PROT_NONE red zone around its
alternate signal stack. Then a small overflow would trigger a SIGSEGV in
handler setup, and be fatal (core dump) whether or not SIGSEGV is
blocked. As with thread stack red zones, that cannot catch all overflows
(or underflows). e.g., a local array as large as page size allocated in
a function called from a handler, but not actually touched before more
calls push more stack, could cause an overflow that silently pushes into
some unrelated allocated pages.
The BSD behavior does not do anything in particular about overflow. But
it does at least avoid the wraparound or "ring buffer effect", so you'll
just get a straightforward all-out overflow down your address space past
the low end of the alternate signal stack. I don't know what the BSD
behavior is for longjmp out of an SA_ONSTACK handler.
The POSIX wording relating to sigaltstack is pretty minimal. I don't
think it speaks to this issue one way or another. (The program that
overflows its stack is clearly in undefined behavior territory of one
sort or another anyhow.)
Given the longjmp issue and the potential for highly subtle complications
in existing programs relying on this in arcane ways deep in their code, I
am very dubious about changing the behavior to the BSD style persistent
flag. I think Shi Weihua's patches have a similar effect by tracking the
SP used in the last handler setup.
I think it would be sensible for the signal handler setup code to detect
when it would itself be causing a stack overflow. Maybe something like
the following patch (untested). This issue exists in the same way on all
machines, so ideally they would all do a similar check.
When it's the handler function itself or its callees that cause the
overflow, rather than the signal handler frame setup alone crossing the
boundary, this still won't help. But I don't see any way to distinguish
that from the valid longjmp case.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
add the DMI strings provided by Islam Amer <pharon@gmail.com>, for
the Compaq Presario V6000 (Quanta/30B7).
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
make io_delay=0xed the default. This frees up port 0x80 which is
a debug port on some machines and locks up certain laptops.
Testing only for now. Try the io_delay=0x80 boot option if this does not
work for you.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
various changes to the in_p/out_p delay details:
- add the io_delay=none method
- make each method selectable from the kernel config
- simplify the delay code a bit by getting rid of an indirect function call
- add the /proc/sys/kernel/io_delay_type sysctl
- change 'io_delay=standard|alternate' to io_delay=0x80 and io_delay=0xed
- make the io delay config not depend on CONFIG_DEBUG_KERNEL
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: "David P. Reed" <dpreed@reed.com>
x86: provide a DMI based port 0x80 I/O delay override.
Certain (HP) laptops experience trouble from our port 0x80 I/O delay
writes. This patch provides for a DMI based switch to the "alternate
diagnostic port" 0xed (as used by some BIOSes as well) for these.
David P. Reed confirmed that port 0xed works for him and provides a
proper delay. The symptoms of _not_ working are a hanging machine,
with "hwclock" use being a direct trigger.
Earlier versions of this attempted to simply use udelay(2), with the
2 being a value tested to be a nicely conservative upper-bound with
help from many on the linux-kernel mailinglist but that approach has
two problems.
First, pre-loops_per_jiffy calibration (which is post PIT init while
some implementations of the PIT are actually one of the historically
problematic devices that need the delay) udelay() isn't particularly
well-defined. We could initialise loops_per_jiffy conservatively (and
based on CPU family so as to not unduly delay old machines) which
would sort of work, but...
Second, delaying isn't the only effect that a write to port 0x80 has.
It's also a PCI posting barrier which some devices may be explicitly
or implicitly relying on. Alan Cox did a survey and found evidence
that additionally some drivers may be racy on SMP without the bus
locking outb.
Switching to an inb() makes the timing too unpredictable and as such,
this DMI based switch should be the safest approach for now. Any more
invasive changes should get more rigid testing first. It's moreover
only very few machines with the problem and a DMI based hack seems
to fit that situation.
This also introduces a command-line parameter "io_delay" to override
the DMI based choice again:
io_delay=<standard|alternate>
where "standard" means using the standard port 0x80 and "alternate"
port 0xed.
This retains the udelay method as a config (CONFIG_UDELAY_IO_DELAY) and
command-line ("io_delay=udelay") choice for testing purposes as well.
This does not change the io_delay() in the boot code which is using
the same port 0x80 I/O delay but those do not appear to be a problem
as David P. Reed reported the problem was already gone after using the
udelay version. He moreover reported that booting with "acpi=off" also
fixed things and seeing as how ACPI isn't touched until after this DMI
based I/O port switch I believe it's safe to leave the ones in the boot
code be.
The DMI strings from David's HP Pavilion dv9000z are in there already
and we need to get/verify the DMI info from other machines with the
problem, notably the HP Pavilion dv6000z.
This patch is partly based on earlier patches from Pavel Machek and
David P. Reed.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Document the fact that __save_processor_state() has to save all CPU
registers referred to by the kernel in case a different kernel is
used to load and restore a hibernation image containing it.
Sigend-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Michael Opdenacker reported:
For backward compatibility with earlier (< 2.6.24) kernels,
arch/i386/boot/bzImage or arch/x86_64/boot/bzImage symbolic links to
arch/x86/boot/bzImage are created when you build an x86 kernel. The
arch/i386 or arch/x86_64 directories are then created for this only
purpose.
Issue: these generated directories and symbolic links are *not cleaned
up* when you run "make mrproper" (and thus "make distclean"). This
disturbs the production of patches, because the source tree is left with
generated files and directories.
Sam has an alternative fix:
The directory is killed during make clean as opposed to make mrproper.
Reported-by: Michael Opdenacker <michael-lists@free-electrons.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Looks like IRQ 31 is assigned to timer 3, even without the patch!
I wonder who wrote the number 31. But the manual says that it is
zero by default.
I think we should check whether the timer has been allocated an IRQ before
proceeding to assign one to it. Here is a patch that does this.
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Tested-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The userspace API for the HPET (see Documentation/hpet.txt) did not work. The
HPET_IE_ON ioctl was failing as there was no IRQ assigned to the timer
device. This patch fixes it by allocating IRQs to timer blocks in the HPET.
arch/x86/kernel/hpet.c | 13 +++++--------
drivers/char/hpet.c | 45 ++++++++++++++++++++++++++++++++++++++-------
include/linux/hpet.h | 2 +-
3 files changed, 44 insertions(+), 16 deletions(-)
Signed-off-by: Balaji Rao <balajirrao@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The following scenario might leave PIT as a disfunctional clock source:
PIT is registered as clocksource
PM_TIMER is registered as clocksource and enables highres/dyntick mode
PIT is switched to oneshot mode
-> now the readout of PIT is bogus, but the user might select PIT
via the sysfs override, which would break the box as the time
readout is unusable.
Unregister the PIT clocksource when the PIT clock event device is switched
into shutdown / oneshot mode.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On x86 the PIT might become an unusable clocksource. Add an unregister
function to provide a possibilty to remove the PIT from the list of
available clock sources.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PIT clocksource is registered unconditionally even when HPET is enabled
or when PIT is replaced by the local APIC timer. In both cases PIT can
not be used as it is stopped and the readout would be stale.
Prevent registering PIT in those cases.
patch depends on:
x86: offer is_hpet_enabled() on !CONFIG_HPET_TIMER too
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
I was confused by FSEC = 10^15 NSEC statement, plus small whitespace
fixes. When there's copyright, there should be GPL.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
the logic in this function is just crazy. It's recursive, but we
can circumvent the creation for the kobject and whole creation of the
threshold_block if some conditions are met. That's why we see the
allocate_threshold_blocks so many times in the callstack, yet only a few
kobjects created.
Then we blow up in kobject_uevent_env() on the first debug printk.
Which means that we are just passing in garbage.
Man, this is one time that comments in code would have been very nice to
have, and why forward goto's into major code blocks are just evil...
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6.25: (1470 commits)
[IPV6] ADDRLABEL: Fix double free on label deletion.
[PPP]: Sparse warning fixes.
[IPV4] fib_trie: remove unneeded NULL check
[IPV4] fib_trie: More whitespace cleanup.
[NET_SCHED]: Use nla_policy for attribute validation in ematches
[NET_SCHED]: Use nla_policy for attribute validation in actions
[NET_SCHED]: Use nla_policy for attribute validation in classifiers
[NET_SCHED]: Use nla_policy for attribute validation in packet schedulers
[NET_SCHED]: sch_api: introduce constant for rate table size
[NET_SCHED]: Use typeful attribute parsing helpers
[NET_SCHED]: Use typeful attribute construction helpers
[NET_SCHED]: Use NLA_PUT_STRING for string dumping
[NET_SCHED]: Use nla_nest_start/nla_nest_end
[NET_SCHED]: Propagate nla_parse return value
[NET_SCHED]: act_api: use PTR_ERR in tcf_action_init/tcf_action_get
[NET_SCHED]: act_api: use nlmsg_parse
[NET_SCHED]: act_api: fix netlink API conversion bug
[NET_SCHED]: sch_netem: use nla_parse_nested_compat
[NET_SCHED]: sch_atm: fix format string warning
[NETNS]: Add namespace for ICMP replying code.
...
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (68 commits)
[MIPS] remove Documentation/mips/GT64120.README
[MIPS] Malta: remaining bits of the board support code cleanup
[MIPS] Malta: make the helper function static
[MIPS] Malta: fix braces at single statement blocks
[MIPS] Malta, Atlas: move an extern function declaration to the header file
[MIPS] Malta: Use C89 style for comments
[MIPS] Malta: else should follow close brace in malta_int.c
[MIPS] Malta: remove a superfluous comment
[MIPS] Malta: include <linux/cpu.h> instead of <asm/cpu.h>
[MIPS] Malta, Atlas, Sead: remove an extern from .c files
[MIPS] Malta: fix oversized lines in malta_int.c
[MIPS] Malta: remove a dead function declaration
[MIPS] Malta: use tabs not spaces
[MIPS] Malta: set up the screen info in a separate function
[MIPS] Malta: check the PCI clock frequency in a separate function
[MIPS] Malta: use the KERN_ facility level in printk()
[MIPS] Malta: use Linux kernel style for structure initialization
[MIPS]: constify function pointer tables
[MIPS] compat: handle argument endianess of sys32_(f)truncate64 with merge_64
[MIPS] Cobalt 64-bits kernels can be safely unmarked experimental
...
This patch factors out the code, which handles the Bonito system
controller. The case of not supporting the DMA coherency is handled
separately to make the logic obvious. Besides, a couple of empty
lines added to beautify the code even further.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
One helper function can become static. This patch adds the needed
keyword.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes a couple of warnings reported by checkpatch.pl.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This was compile-tested using default configs for the boards
affected by this change.
This patch does not introduce any functional changes.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove comments in C99 style and make checkpatch.pl happy.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes two errors reported by checkpatch.pl.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Using the "We die here" comment right before calling the die()
function is an extremely vivid example of overcommenting.
Remove the redundant comment and save one line.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The checkpatch.pl script reported a few warnings about header files.
This patch fixes these warnings.
Compile-tested using the default Malta config.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch moves the "extern" declaration for the function
mips_reboot_setup() from the board setup .c files to the
header file include/asm-mips/mips-boards/generic.h.
This fixes a warning produced by the checkpatch.pl script.
No functional changes introduced.
This was compile-tested by building the kernel for all
three boards affected by this change. All builds finished
successfully.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes all "line over 80 characters" warnings found
in arch/mips/mips-boards/malta/malta_int.c by the checkpatch.pl
script.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Neither is the mips_rtc_get_time() routine defined anywhere in
the MIPS architecture-specific code, nor does anyone call it any
more. This patch removes the extern declaration of this fossil.
This patch does not introduce any functional changes.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch fixes all "use tabs not spaces" warnings reported by
the checkpatch.pl script on the board-specific files.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a separate short and sweet function to initialize
the screen_info global variable.
This improves readability of the Malta board setup code.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds a separate short and sweet function to check the
PCI clock frequency. This is to improve readability of the Malta
setup code.
Along the way, a couple of coding style violations are fixed.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds the KERN_ macros to printk() calls. Where applicable,
spaces are replaced by tabs.
These changes noticeably reduce the number of errors and warnings
reported by the checkpatch.pl script for the malta_int.c file.
Before the patch: total: 47 errors, 20 warnings, 354 lines checked
After the patch: total: 34 errors, 7 warnings, 355 lines checked
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch reformats the structure initialization code thus
making the latter look idiomatic.
No functional changes introduced.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The Qemu platform was originally implemented to have an easily supportable
platform until Qemu reaches a state where it emulates a real world system.
Since the latest release Qemu is capable of emulating the MIPSsim and
Malta platforms, so this goal has been reached. The Qemu plaform is also
rather underfeatured so less useful than a Malta emulation.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
I also changed the name to pvc_mutex, and moved the define to the file
it's used in which allows it to be static.
Signed-off-by: Daniel Walker <dwalker@mvista.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for the GPIO connected system button on the MTX-1
boards. Default configuration is updated accordingly.
Signed-off-by: Florian Fainelli <florian.fainelli@telecomint.eu>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Moved the eXcite local config to excite directory.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Added cpu_wait() to machine_halt().
For the power reduction in halt.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Removed unneeded button check for reset.
Because, the Cobalt has power switch.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Moved vr41xx_calculate_clock_frequency() to plat_time_init().
This function relates to the timer function.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
A raw binary boots about twice as fast as SREC.
The possibility to generate SREC binaries remains by simply using the
vmlinux.srec target but seems only useful for the probably hypothetical
case where one of these systems is booted over a serial interface.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The latest draft version of the MIPS Architecture Specification extends the
6 bit event field by adding a directly adjacent 4-bit EventExt field for a
total of 10 bits.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
- EISA support for non PCI RMs (RM200 and RM400-xxx). The major part
is the splitting of the EISA and onboard ISA of the RM200, which
makes the EISA bus on the RM200 look like on other RMs.
- 64bit kernel support
- system type detection is now common for big and little endian
- moved sniprom code to arch/mips/fw
- added call_o32 function to arch/mips/fw/lib, which uses a private
stack for calling prom functions
- fix problem with ISA interrupts, which makes using PIT clockevent
possible
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds IDs for new Au1200 variants: Au1210 and Au1250.
They are essentially identical to the Au1200 except for the Au1210
which has a different SoC-ID in the PRId register [bits 31:24].
The Au1250 is a "Au1200 V0.2".
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
These symbols appear in oprofile output, stacktraces and similar but only
make the output harder to read. Many identical symbol names such as
"both_aligned" were also being used in multiple source files making it
impossible to see which file actually was meant. So let's get rid of them.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add support for SGI IP28 machines (Indigo 2 with R10k CPUs)
This work is mainly based on Peter Fuersts work.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
According to Broadcom the PT systems are production test systems which
never reached customers so no need to keep the fragmentary support we
currently have.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Not cache coherent R10k systems (like IP28) need to do real cache
invalidates in dma_cache_sync().
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
IP28 needs special treatment to avoid speculative accesses. gcc
takes care for .c code, but for assembly code we need to do it
manually.
This is taken from Peter Fuersts IP28 patches.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This patch adds support for txx9wdt driver to rbhma3100, rbhma4200 and
rbhma4500 platform.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
R10k non coherent machines need a real dma cache invalidate to get rid of
speculative stores in cache. For other machines this promises a slight
speedup.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move registration into the actual platform code instead of making a
desparate attempt at sharing the hand full of likes of code in pcspeaker.c.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Given that the corresponding source file i2c-yosemite.c file was
removed in commit daa4a68f90, and that
no one else includes this file, it seems safe to delete it.
Signed-off-by: Robert P. J. Day <rpjday@crashcourse.ca>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Use strchr instead of strstr when searching for a single character
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Since all the callers of the PHYS_TO_XKPHYS macro call with a constant,
put the cast to LL inside the macro where it really should be rather
than in all the callers. This makes macros like PHYS_TO_XKSEG_UNCACHED
work without gcc whining.
Signed-off-by: Andrew Sharp <andy.sharp@onstor.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Removed unused mips_machtype. These are only set but not used.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Remove some unnecessary codes, includes and files.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This complements the generic R4000/R4400 errata workaround code and adds
bits for the daddiu problem. In most places it just modifies handwritten
assembly code so that the assembler is allowed to use a temporary register
as daddiu may now be treated as a macro that expands to a sequence of li
and daddu. It is the AT register or, where AT is unavailable or used
explicitly for another purpose, an explicitly-named register is selected,
using the .set at=<reg> feature added recently to gas. This feature is
only used if CONFIG_CPU_DADDI_WORKAROUNDS has been set, so if the
workaround remains disabled, the required version of binutils stays
unchanged.
Similarly, daddiu instructions put in branch delay slots in noreorder
fragments are now taken out of them and the assembler is allowed to
reorder them itself as possible (which it does making the whole idea of
scheduling them into delay slots manually questionable).
Also in the very few places where such a simple conversion was not
possible, a handcoded longer sequence is implemented.
Other than that there are changes to code responsible for building the
TLB fault and page clear/copy handlers to avoid daddiu as appropriate.
These are only effective if the erratum is verified to be present at the
run time.
Finally there is a trivial update to __delay(), because it uses daddiu in
a branch delay slot.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This is the gereric part of R4000/R4400 errata workarounds. They include
compiler and assembler support as well as some source code modifications
to address the problems with some combinations of multiply/divide+shift
instructions as well as the daddi and daddiu instructions.
Changes included are as follows:
1. New Kconfig options to select workarounds by platforms as necessary.
2. Arch top-level Makefile to pass necessary options to the compiler; also
incompatible configurations are detected (-mno-sym32 unsupported as
horribly intrusive for little gain).
3. Bug detection updated and shuffled -- the multiply/divide+shift problem
is lethal enough that if not worked around it makes the kernel crash in
time_init() because of a division by zero; the daddiu erratum might
also trigger early potentially, though I have not observed it. On the
other hand the daddi detection code requires the exception subsystem to
have been initialised (and is there mainly for information).
4. r4k_daddiu_bug() added so that the existence of the erratum can be
queried by code at the run time as necessary; useful for generated code
like TLB fault and copy/clear page handlers.
5. __udelay() updated as it uses multiplication in inline assembly.
Note that -mdaddi requires modified toolchain (which has been maintained
by myself and available from my site for ~4years now -- versions covered
are GCC 2.95.4 - 4.1.2 and binutils from 2.13 onwards). The -mfix-r4000
and -mfix-r4400 have been standard for a while though.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Forgot to export this one. Needed when pasemi_mac is compiled as a module.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pasemi: DMA engine management library
Introduce a DMA management library to manage the various DMA resources
on the PA Semi SoCs. Since several drivers need to allocate these shared
resources, provide some abstractions as well as allocation/free functions
for channels, etc.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* use irq_handler_t where appropriate
* no need to use 'irq' function arg, its already stored in a data struct
* rename irq handler 'irq' argument to 'dummy', where the function
has been analyzed and proven not to use its first argument.
* remove always-false "dev_id == NULL" test from irq handlers
* remove pointless casts from void*
* declance: irq argument is not const
* add KERN_xxx printk prefix
* fix minor whitespace weirdness
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
"make dep" is no longer required in kernel 2.6, but was still mentioned
in some places.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch drops TOPDIR from frv Makefiles.
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6: (197 commits)
sh: add spi header and r2d platform data V3
sh: update r7780rp interrupt code
sh: remove consistent alloc stuff from the machine vector
sh: use declared coherent memory for dreamcast pci ethernet adapter
sh: declared coherent memory support V2
sh: Add support for SDK7780 board.
sh: constify function pointer tables
sh: Kill off -traditional for linker script.
cdrom: Add support for Sega Dreamcast GD-ROM.
sh: Kill off hs7751rvoip reference from arch/sh/Kconfig.
sh: Drop r7780rp_defconfig, use r7780mp_defconfig as kbuild default.
sh: Kill off dead HS771RVoIP board support.
sh: r7785rp: Fix up DECLARE_INTC_DESC() arg mismatch.
sh: r7785rp: Hook up the rest of the HL7785 FPGA IRQ vectors.
sh: r2d - enable sm501 usb host function
sh: remove voyagergx
sh: r2d - add lcd planel timings to sm501 platform data
sh: Add OHCI and UDC platform devices for SH7720.
sh: intc - remove default interrupt priority tables
sh: Correct pte size mismatch for X2 TLB.
...
* orion: (26 commits)
[ARM] Orion: implement power-off method for QNAP TS-109/209
[ARM] Orion: add support for QNAP TS-109/TS-209
[ARM] Orion: I2C support
[I2C] i2c-mv64xxx: Don't set i2c_adapter.retries
[I2C] Split mv643xx I2C platform support
[ARM] Orion: enable CONFIG_RTC_DRV_M41T80 for D-Link DNS-323
[ARM] Orion defconfig
[ARM] Orion: add support for Orion/MV88F5181 based D-Link DNS-323
[ARM] Orion: MV88F5181 support bits
[ARM] Orion: Buffalo/Revogear Kurobox Pro support
[ARM] OrionNAS RD board support
[ARM] Orion: support for Marvell Orion-2 (88F5281) Development Board
[ARM] Orion: common platform setup for Gigabit Ethernet port
[ARM] Orion: platform device registration for UART, USB and NAND
[ARM] Orion: system timer support
[ARM] Orion edge GPIO IRQ support
[ARM] Orion: IRQ support
[ARM] Orion: provide GPIO method for enabling hardware assisted blinking
[ARM] Orion: GPIO support
[ARM] Orion: programable address map support
...
Conflicts:
arch/arm/Kconfig
arch/arm/Makefile
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the supported clocks on the S3C2440 and S3C2442 to
better represent the DVS state which controls whether FCLK or HCLK
is fed to the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Merge together the bits of the S3C2440 and S3C2442 clock code
that can be.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the reverse of s3c2410_gpio_getirq to convert
a IRQ number into a GPIO pin number.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the S3C2412 fclk is derived from msysclk, not straight from
the MPLL output. Set clk_f.parent appropriately.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The msysclk clock was checking for the wrong PLL for the
parent in s3c2412_setparent_msysclk(), trying the UPLL instead
of the MPLL output.
Also ensure the mpll and fclks are at the same rate at init time.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the channel parameter to s3c2410_dma_ctrl() in s3c2410_dma_enqueue()
if the S3C2410_DMAF_AUTOSTART is set on the channel.
Spotted by Steven Ryu at Samsung.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The s3c2410_dma_request() function should return the channel allocated
instead of zero for success.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The core resume code may have caused glitches in the GPIO when
restoring the GPIO state due to the order in which the GPIO registers
were being written.
Change the restore process take into account the state of the
GPIOs on resume and the state the system wants to restore them to.
See the code comments in the patch for more details of the process.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the call s3c2410_gpio_getpull() to return the
current state of the pin's pull-up.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If an DMA channel was active at suspend, then ensure that
it is correctly reconfigured when the system resumes.
Note, the previous policy was for each driver to handle their
own reconfiguration on resume. The policy has been changed to
make the individual driver's job easier.
Signed-off-by: Ben Dooks <ben-linux@flfuf.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The current S3C24XX DMA code does not allow for an peripheral
that has one channel for RX and another for TX.
This patch adds a per-cpu dma operation to select the transmit
or receive channel, and adds support to the S3C2412 for the
seperate DMA channels for TX and RX.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add s3c2412_gpio_set_sleepcfg() to allow the setting of the sleep
configuration of the GPIO blocks.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add armclk to the S3C2412 to indicate the current clock connected to
the ARM core.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add checks for clk_set_rate() and ensure that we do not allow set_rate
to be called for a clock that does not have it defined. Add default
methods for fclk, hclk, pclk and mpll.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Check if the sleep command returns due to a pending interrupt
in the standby unit. If this happens, try and ack the IRQ
before re-trying the resume.
It is currently unclear whether the resume can be backed out
of at this stage as this could cause a problem with level
based interrupts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ensure that if the RTC IRQ is not selected for wake in the
base configuration, then the PWRCFG has the same value set
in it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS device is being registered by the Simtec Audio
driver, and thus registering here causes an error due
to device tree naming collision.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
S3C2412_GPESLPCON does not exist in the register
mappings, so remove it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The IIS and SDI register hw_addr definitions are
incorrect in the DMA map for the S3C2412.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The S3C2412 GPIO is similar enough to the S3C2410 that
it can use it as a base for GPIO functionality.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We have a default display set to 4, when we only have
three registered displays. Fix this argument (a seperate
patch has been generated to ensure that the LCD driver
takes notice of this bug)
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for Toradex' PXA27x based Colibri module.
It's kept as simple as possible to only provide basic functionality.
A default config is also included.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix all those PXA mci_init functions which return -1 rather than
propagating the error code to the higher levels. Remove the silly
set_irq_type() calls as well - use the flags for request_irq()
instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch refactors the code in corgi_lcd.c moving it to the board
specific corgi and spitz files where appropriate instead of the
existing ifdef mess which hinders readability.
Fix spitz_get_hsync_len() to call get_hsync_invperiod so pxafb can be
compiled as a module.
The confusing variables which represent the inverse horizintal sync
period are renamed to "invperiod" consistently.
An incorrect comment in corgi_ts.c is also corrected.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds baseboard support for the phyCORE-PXA270 development
kit (aka PCM-990).
This example shows how to use some phyCORE-PXA270 CPU module features
on a baseboard in a standard manner. It could be used as a starting
point for custom baseboard development.
V2:
After comments by Eric Miao:
- IRQ chained handler fixed
- video/graphic support moved to separate patch
- ifdef/endif hell reduced ;-)
V3:
After comments by Russell King
- initialise the mmci platform data statically
V4:
After comments by Russell King
- wrong return value in pcm990_mci_init() fixed
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds a basic configration for the phyCORE-PXA270 development kit. In this case development kit means PCM-990 (main baseboard).
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds main support for the generic phyCORE-PXA270 CPU module
(aka PCM-027). Its as generic as possible to support any kind of baseboard.
Note: Neither the CPU module nor the pcm027.c implementation can work without
a baseboard support. Baseboard support can be added by the PCM-990 or any
custom variant.
V2:
After comments by Eric Miao:
- Currently unsupported devices moved into separate patch
- direct call of baseboard initialisation
V3:
After comments by Russell King
- sort include files
- setting RTC bit for power control removed
- style problems fixed (discovered by checkpatch.pl)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smc91x is shared between many different platforms. Each platform needs
to specify the interrupt type, and in some cases the irq type depends
on more than just the build configuration - it depends on runtime
checks.
Rather than throwing this code into the SMC_IRQ_FLAGS definition, provide
a way for these flags to be passed via the IRQ resource itself.
Note that IRQF_TRIGGER_* constants are intentionally defined to correspond
with the IORESOURCE_IRQ_* interrupt type flags, in much the same way that
the low bits of PCI iomem resources correspond with the BAR flag bits.
Also provide a way to configure smc91x to read the IRQ flags from the
resource. Once all platforms have been converted over (signified
by all definitions of SMC_IRQ_FLAGS being -1) SMC_IRQ_FLAGS should
be removed.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
default to
- PXA300/PXA310 support only (there isn't any littleton board with PXA320
processor for now)
- smc91x ethernet support with NFS rootfs
- LCD framebuffer support with graphics console
Signed-off-by: eric miao <eric.miao>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This includes irda, gpio keys, pxafb, backlight, ohci and flash
(read-only).
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch contains the base code to boot the Toshiba e330, e740,
e750, e400, and e800 PDAs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds back the registration of HWUART clock on pxa25x
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the xtime write mode seqlock into timer_tick(), so it only
surrounds the call to do_timer().
This avoids a deadlock in update_process_times() ...
hrtimer_get_softirq_time() which tries to get a read mode seqlock
on xtime, thereby preventing booting.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original code incorrectly returns Hz instead of KHz.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch converts um to use blk_end_request interfaces.
Related 'uptodate' arguments are converted to 'error'.
As a result, the interface of internal function, ubd_end_request(),
is changed.
Cc: Jeff Dike <jdike@karaya.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch converts arm's OMAP mailbox driver to use
blk_end_request interfaces.
If the original code was converted literally, blk_end_request would
be called with '-EIO' because end_that_request_last() were called
with '0' (i.e. failure).
But I think these '0's are bugs in the original code because it's
unlikely that all requests are treated as failure.
(The bugs should have no effect unless these requests have an end_io
callback.)
So I changed them to pass '0' (i.e. success) to blk_end_request.
Cc: Toshihiro Kobayashi <toshihiro.kobayashi@nokia.com>
Cc: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: Kiyoshi Ueda <k-ueda@ct.jp.nec.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This patch adds the header file asm/spi.h and board specific code for the
r2d board. The header file contains a structure that should be used to
point out a single spi bus. The board specific code for r2d is updated with
such a structure for the new spi_sh_sci driver. The structure contains a
chip select callback plus information about the R9701 rtc chip which is
attached to the spi bus.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the board specific irq code for r7780rp. The new code is
very similar to the other highlander implementations, with the exception that
the r7780rp handles pci interrupts using IRL. To simplify the pci code and
use the same interrupt numbers as r7780mp and r7785rp we hook in to the
cpu specific pci vectors.
The pci interrupts and the push switch all work well with and without this
patch. CF and AX88796 are not ok though and the source of the problem is
unknown at this point. The AX88796 does for not detect it's proper mac
address (IPL gets it right) and the kernel hangs on CF access. As a workaround
this patch removes the CF and the AX88796 from the platform datain case of
r7780rp.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch makes the dreamcast use the recently added declared coherent
memory functions to point out the memory window suitable for dma.
Apart from cleaning up, this gives the dreamcast a proper memory allocator
for pci dma memory.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds declared coherent memory support to the sh architecture. All
functions are based on the x86 implementation. Header files are adjusted to
use the new functions instead of the former consistent_alloc() code.
This version includes the few changes what were included in the fix patch
together with modifications based on feedback from Paul.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add support for Renesas Technology Europe SDK7780 board.
Signed-off-by: Nicholas Beck <nbeck@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some of Sam's new work in the kbuild queue depend on ## concatenation
within the linker script, which doesn't work when -traditional is
enabled. -traditional is a legacy remnant anyways, and we no longer
require it for anything, so kill it off completely.
Noted-by: Andreas Schwab <schwab@suse.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove reference to board deleted in commit 758e06ded4c48024835ef0a14627afcde2e25929
Signed-off-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch tells the sm501 mfd driver to build platform data for the
sm501 usb host driver.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes redundant irq handling code together with unused
consistent alloc code. R2D uart setup code is changed to use
sm501-regs.h and unused header files are removed.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds timings to drive a Sharp LQ104V1DG21 lcd panel that can
be hooked up to R2D-1 or R2D-PLUS. The sm501fb driver should leave the
pins FPEN and VBIASEN alone, and this patch instructs the driver to do
so by not setting flags flags for these pins.
This patch works best together with the patch posted to the
linux-fbdev-devel list "sm501fb: control panel pin usage with platform
data flags", but this patch can be merged independently.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch removes interrupt priority tables from the intc code.
Optimal priority assignment varies with embedded application anyway,
so keeping the interrupt priority tables together with cpu-specific
code doesn't make sense.
The function intc_set_priority() should be used instead to set the
desired interrupt priority level.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides a correct value for CONFIG_SH_PCLK_FREQ for the
SH7712 solution engine when used with the board's default factory
settings. This results in the board running at its maximum CPU clock
rate (200 MHz).
Signed-off-by: Andrew Murray <amurray@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch provides specific clock support for the SH7712.
Signed-off-by: Andrew Murray <amurray@mpc-data.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Change occurances of:
bool
default X
to:
def_bool X
Change ocurances of:
bool "Foo"
default X
to:
def_bool X
prompt "Foo"
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds in the L1I/L1D/L2 cache shape support to their respective
entries in the ELF auxvt, based on the Alpha implementation. We use
this on the userspace libc side for calculating a tightly packed
SHMLBA amongst other things.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch changes the uImage target so that it generates a wrapped
compressed vmlinux, rather than a wrapped zImage. The previous version
matched the ARM, this version matches the PPC. However I would question
how useful a self decompressing image is with a boot loader which does
decompression, so I think this is more useful. I also feel it matches
the descrition in the help text ("Compressed kernel image") better.
Signed-off-by: Thomas Betker <thomas.betker@5etech.eu>
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This saves us from having to use kmalloc() for the fixmap entries,
which is needed early for the uncached fixmap.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently most of the 29-bit physical parts do P1/P2 segmentation
with a 1:1 cached/uncached mapping, jumping between the two to
control the caching behaviour. This provides the basic infrastructure
to maintain this behaviour on 32-bit physical parts that don't map
P1/P2 at all, using a shiny new linker section and corresponding
fixmap entry.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements kernel-level atomic rollback built on top of gUSA,
as an alternative non-IRQ based atomicity method. This is generally
a faster method for platforms that are lacking the LL/SC pairs that
SH-4A and later use, and is only supportable on legacy cores.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Shoves a magic word in to the empty_zero_page section for the
bootloader to work out whether to start the kernel in 29-bit
or 32-bit mode.
[ Renesas CPUs already take care of the initial PMB mappings entirely
in hardware and decide on 29-bit/32-bit physical depending on which
pin powered up the CPU, so this is mostly for ST parts. -- PFM ].
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
mem= can't be used to grow the size of kernel memory, so provide a
warning to that effect.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH7263 (SH-2A) CPU.
This particular CPU is a superset of SH7203, adding some additional
peripheral blocks and hooking up additional (reserved on SH7203)
vectors in the INTC block.
No visibly nasty surprises, yet..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was using the absolute path, which was confusing the make target.
Switch it to just 'zImage', as per powerpc.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This is trivial, in that they're both effectively the same for the base
relocations anyways. SH-5 doesn't need the unaligned bits, and has a
few extra relocations, which are never hit on non-SH5 parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
