Remove harmful BUG_ON() from ata_bmdma_qc_issue(),
as it casts too wide of a net and breaks sata_mv.
It also crashes the kernel while doing the BUG_ON().
There's already a WARN_ON_ONCE() further down to catch
the case of POLLING for a BMDMA operation.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
Fix DSM/TRIM commands in sata_mv (v2).
These need to be issued using old-school "BM DMA",
rather than via the EDMA host queue.
Since the chips don't have proper BM DMA status,
we need to be more careful with setting the ATA_DMA_INTR bit,
since DSM/TRIM often has a long delay between "DMA complete"
and "command complete".
GEN_I chips don't have BM DMA, so no TRIM for them.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Cc: stable@kernel.org
ata_qc_issue() BUG_ON()s on data commands w/o data, which may be
submitted via SG_IO. Be less of a drama queen and just trigger
WARN_ON_ONCE() and fail the command with AC_ERR_SYSTEM.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Stefan Hübner <stefan.huebner@stud.tu-ilmenau.de>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
dma_dwc_xfer_setup() returns an int and "dma_chan" needs to be signed
for the error handling to work.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
88SE9128 can do FBS and sets it in HOST_CAP but forgets to set FBSCP
in PORT_CMD. Implement AHCI_HFLAG_YES_FBS and apply it to 88SE9128.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Winbond W83759A controller is fully supported by pata_legacy driver
so remove no longer needed pata_winbond driver.
Leave PATA_WINBOND_VLB config option for compatibility reasons
and teach pata_legacy to preserve the old behavior of pata_winbond
driver.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Commit d62f5576 (pata_cmd64x: fix handling of address setup timings)
incorrectly called ata_timing_compute() on UDMA mode on 0 @UT leading
to devide by zero fault. Revert it until better fix is available.
This is reported in bko#16607 by Milan Kocian who also root caused it.
https://bugzilla.kernel.org/show_bug.cgi?id=16607
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-and-root-caused-by: Milan Kocian <milan.kocian@wq.cz>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
One of the recent changes caused complilation of
drivers/pci/hotplug/pciehp_core.c to fail. Fix this issue.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The ioctl path and the scsi tape path were not accounting
for their additions to the queue depth.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'upstream/core' of git://git.kernel.org/pub/scm/linux/kernel/git/jeremy/xen:
xen: handle events as edge-triggered
xen: use percpu interrupts for IPIs and VIRQs
No need to call input_free_device() after input_unregister_device().
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Introduced by 987a6c0298 a swap in max/min
calculation gets fixed by this patch.
Reported-by: Bruno Prémont <bonbons@linux-vserver.org>
Signed-off-by: Christoph Fritz <chf.fritz@googlemail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Commit 8bf0223ed515be24de0c671eedaff49e78bebc9c (hwmon, k8temp: Fix
temperature reporting for ASB1 processor revisions) fixed temperature
reporting for ASB1 CPUs. But those CPU models (model 0x6b, 0x6f, 0x7f)
were packaged both as AM2 (desktop) and ASB1 (mobile). Thus the commit
leads to wrong temperature reporting for AM2 CPU parts.
The solution is to determine the package type for models 0x6b, 0x6f,
0x7f.
This is done using BrandId from CPUID Fn8000_0001_EBX[15:0]. See
"Constructing the processor Name String" in "Revision Guide for AMD
NPT Family 0Fh Processors" (Rev. 3.46).
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: stable@kernel.org [.32.x, .33.x, .34.x, .35.x]
Reported-by: Vladislav Guberinic <neosisani@gmail.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Fix the following build warning:
CC [M] drivers/hwmon/coretemp.o
drivers/hwmon/coretemp.c: In function "coretemp_init":
drivers/hwmon/coretemp.c:521: warning: unused variable "n"
drivers/hwmon/coretemp.c:521: warning: unused variable "p"
Introduced by commit 851b29cb3b. When
you drop code, you also have to drop the variables this code was
using.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Chen Gong <gong.chen@linux.intel.com>
Cc: Rudolf Marek <r.marek@assembler.cz>
Cc: Huaxu Wan <huaxu.wan@intel.com>
This patch fixes a crash during shutdown reported below. The crash is
caused by accessing already freed task structs. The fix changes the
order for registering and unregistering notifier callbacks.
All notifiers must be initialized before buffers start working. To
stop buffer synchronization we cancel all workqueues, unregister the
notifier callback and then flush all buffers. After all of this we
finally can free all tasks listed.
This should avoid accessing freed tasks.
On 22.07.10 01:14:40, Benjamin Herrenschmidt wrote:
> So the initial observation is a spinlock bad magic followed by a crash
> in the spinlock debug code:
>
> [ 1541.586531] BUG: spinlock bad magic on CPU#5, events/5/136
> [ 1541.597564] Unable to handle kernel paging request for data at address 0x6b6b6b6b6b6b6d03
>
> Backtrace looks like:
>
> spin_bug+0x74/0xd4
> ._raw_spin_lock+0x48/0x184
> ._spin_lock+0x10/0x24
> .get_task_mm+0x28/0x8c
> .sync_buffer+0x1b4/0x598
> .wq_sync_buffer+0xa0/0xdc
> .worker_thread+0x1d8/0x2a8
> .kthread+0xa8/0xb4
> .kernel_thread+0x54/0x70
>
> So we are accessing a freed task struct in the work queue when
> processing the samples.
Reported-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: stable@kernel.org
Signed-off-by: Robert Richter <robert.richter@amd.com>
Casting "pep->tx_desc_dma" to to a struct tx_desc pointer makes gcc
complain:
drivers/net/pxa168_eth.c:657: warning:
cast to pointer from integer of different size
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function changed recently. It now takes a struct
ifreq pointer directly.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A couple issues here:
* Some resources weren't released.
* If alloc_etherdev() failed it would have caused a NULL dereference
because "pep" would be null when we checked "if (pep->clk)".
* Also it's better to propagate the error codes from mdiobus_register()
instead of just returning -ENOMEM.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"pep->pd" isn't checked consistently in this function. For example it's
dereferenced unconditionally on the next line after the end of the if
condition. This function is only called from pxa168_eth_probe() and
pep->pd is always non-NULL so I removed the check.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is possible that phylib will call adjust_link before returning
from {,of_}phy_connect(), which may cause the following [very rare,
though] oops upon reopening the device:
Unable to handle kernel paging request for data at address 0x0000024c
Oops: Kernel access of bad area, sig: 11 [#1]
PREEMPT SMP NR_CPUS=2 LTT NESTING LEVEL : 0
P1021 RDB
Modules linked in:
NIP: c0345dac LR: c0345dac CTR: c0345d84
TASK = dffab6b0[30] 'events/0' THREAD: c0d24000 CPU: 0
[...]
NIP [c0345dac] adjust_link+0x28/0x19c
LR [c0345dac] adjust_link+0x28/0x19c
Call Trace:
[c0d25f00] [000045e1] 0x45e1 (unreliable)
[c0d25f30] [c036c158] phy_state_machine+0x3ac/0x554
[...]
Here is why. Drivers store phydev in their private structures, e.g.
gianfar driver:
static int init_phy(struct net_device *dev)
{
...
priv->phydev = of_phy_connect(...);
...
}
So that adjust_link could retrieve it back:
static void adjust_link(struct net_device *dev)
{
...
struct phy_device *phydev = priv->phydev;
...
}
If the device has been opened before, then phydev->state is set to
PHY_HALTED (or undefined if the driver didn't call phy_stop()).
Now, phy_connect starts the PHY state machine before returning phydev to
the driver:
phy_start_machine(phydev, NULL);
if (phydev->irq > 0)
phy_start_interrupts(phydev);
return phydev;
The time between 'phy_start_machine()' and 'return phydev' is undefined.
The start machine routine delays execution for 1 second, which is enough
for most cases. But under heavy load, or if you're unlucky, it is quite
possible that PHY state machine will execute before phy_connect()
returns, and so adjust_link callback will try to dereference phydev,
which is not yet ready.
To fix the issue, simply initialize the PHY's state to PHY_READY during
phy_attach(). This will ensure that phylib won't call adjust_link before
phy_start().
Signed-off-by: Anton Vorontsov <avorontsov@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The PCIe port driver's module exit routine is never used, so drop it.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
The PCIe PME code only consists of one file, so it doesn't need to
occupy its own directory. Move it to drivers/pci/pcie/pme.c and
remove the contents of drivers/pci/pcie/pme .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
In principle PCIe port services may be enabled by the BIOS, so it's
better to disable them during port initialization to avoid spurious
events from being generated.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
After commit 852972acff (ACPI: Disable
ASPM if the platform won't provide _OSC control for PCIe) control of
the PCIe Capability Structure is unconditionally requested by
acpi_pci_root_add(), which in principle may cause problems to
happen in two ways. First, the BIOS may refuse to give control of
the PCIe Capability Structure if it is not asked for any of the
_OSC features depending on it at the same time. Second, the BIOS may
assume that control of the _OSC features depending on the PCIe
Capability Structure will be requested in the future and may behave
incorrectly if that doesn't happen. For this reason, control of
the PCIe Capability Structure should always be requested along with
control of any other _OSC features that may depend on it (ie. PCIe
native PME, PCIe native hot-plug, PCIe AER).
Rework the PCIe port driver so that (1) it checks which native PCIe
port services can be enabled, according to the BIOS, and (2) it
requests control of all these services simultaneously. In
particular, this causes pcie_portdrv_probe() to fail if the BIOS
refuses to grant control of the PCIe Capability Structure, which
means that no native PCIe port services can be enabled for the PCIe
Root Complex the given port belongs to. If that happens, ASPM is
disabled to avoid problems with mishandling it by the part of the
PCIe hierarchy for which control of the PCIe Capability Structure
has not been received.
Make it possible to override this behavior using 'pcie_ports=native'
(use the PCIe native services regardless of the BIOS response to the
control request), or 'pcie_ports=compat' (do not use the PCIe native
services at all).
Accordingly, rework the existing PCIe port service drivers so that
they don't request control of the services directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
It is possible that the BIOS will not grant control of all _OSC
features requested via acpi_pci_osc_control_set(), so it is
recommended to negotiate the final set of _OSC features with the
query flag set before calling _OSC to request control of these
features.
To implement it, rework acpi_pci_osc_control_set() so that the caller
can specify the mask of _OSC control bits to negotiate and the mask
of _OSC control bits that are absolutely necessary to it. Then,
acpi_pci_osc_control_set() will run _OSC queries in a loop until
the mask of _OSC control bits returned by the BIOS is equal to the
mask passed to it. Also, before running the _OSC request
acpi_pci_osc_control_set() will check if the caller's required
control bits are present in the final mask.
Using this mechanism we will be able to avoid situations in which the
BIOS doesn't grant control of certain _OSC features, because they
depend on some other _OSC features that have not been requested.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
There is the assumption in acpi_pci_osc_control_set() that it is
always sufficient to compare the mask of _OSC control bits to be
requested with the result of an _OSC query where all of the known
control bits have been checked. However, in general, that need not
be the case. For example, if an _OSC feature A depends on an _OSC
feature B and control of A, B plus another _OSC feature C is
requested simultaneously, the BIOS may return A, B, C, while it would
only return C if A and C were requested without B.
That may result in passing a wrong mask of _OSC control bits to an
_OSC control request, in which case the BIOS may only grant control
of a subset of the requested features. Moreover, acpi_pci_run_osc()
will return error code if that happens and the caller of
acpi_pci_osc_control_set() will not know that it's been granted
control of some _OSC features. Consequently, the system will
generally not work as expected.
Apart from this acpi_pci_osc_control_set() always uses the mask
of _OSC control bits returned by the very first invocation of
acpi_pci_query_osc(), but that is done with the second argument
equal to OSC_PCI_SEGMENT_GROUPS_SUPPORT which generally happens
to affect the returned _OSC control bits.
For these reasons, make acpi_pci_osc_control_set() always check if
control of the requested _OSC features will be granted before making
the final control request. As a result, the osc_control_qry and
osc_queried members of struct acpi_pci_root are not necessary any
more, so drop them and remove the remaining code referring to them.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make acpi_pci_query_osc() use an additional pointer argument to
return the mask of control bits obtained from the BIOS to the
caller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Make acpi_pci_osc_control_set() attempt to find the handle of the
_OSC object under the given PCI root bridge object after verifying
that its second argument is correct and that there is a struct
acpi_pci_root object for the given root bridge handle, which is
more logical than the old code.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reviewed-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce kernel command line switch pcie_ports= allowing one to
disable all of the native PCIe port services, so that PCIe ports
are treated like PCI-to-PCI bridges.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Introduce a function allowing the caller to check whether to try to
enable PCIe AER.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Fix this error on an s390 allyesconfig build:
linux-2.6/drivers/net/caif/caif_spi.c:98:
undefined reference to `dma_free_coherent'
Cc: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When converting this to the new wait_for macro I inverted the wait
condition, which causes all sorts of problems. So correct it to fix
several failures caused by the bad wait (flickering, bad output
detection, tearing, etc.).
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Tested-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Xen events are logically edge triggered, as Xen only calls the event
upcall when an event is newly set, but not continuously as it remains set.
As a result, use handle_edge_irq rather than handle_level_irq.
This has the important side-effect of fixing a long-standing bug of
events getting lost if:
- an event's interrupt handler is running
- the event is migrated to a different vcpu
- the event is re-triggered
The most noticable symptom of these lost events is occasional lockups
of blkfront.
Many thanks to Tom Kopec and Daniel Stodden in tracking this down.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Tom Kopec <tek@acm.org>
Cc: Daniel Stodden <daniel.stodden@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
IPIs and VIRQs are inherently per-cpu event types, so treat them as such:
- use a specific percpu irq_chip implementation, and
- handle them with handle_percpu_irq
This makes the path for delivering these interrupts more efficient
(no masking/unmasking, no locks), and it avoid problems with attempts
to migrate them.
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
We should pass the data to the data register.
Signed-off-by: Jianwei Yang <jianwei.yang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It looks like there is an off-by-one error in one of your changes to
drivers/staging/rar_register/rar_register.c:
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This build bug triggers:
drivers/built-in.o: In function `mantis_exit':
(.text+0x377413): undefined reference to `ir_input_unregister'
drivers/built-in.o: In function `mantis_input_init':
(.text+0x3774ff): undefined reference to `__ir_input_register'
If MANTIS_CORE is enabled but IR_CORE is not. Add the correct
dependency.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If netconsole is in use, there is a possibility for deadlock in 3c59x between
boomerang_interrupt and boomerang_start_xmit. Both routines take the vp->lock,
and if netconsole is in use, a pr_* call from the boomerang_interrupt routine
will result in the netconsole code attempting to trnasmit an skb, which can try
to take the same spin lock, resulting in deadlock.
The fix is pretty straightforward. This patch allocats a bit in the 3c59x
private structure to indicate that its handling an interrupt. If we get into
the transmit routine and that bit is set, we can be sure that we have recursed
and will deadlock if we continue, so instead we just return NETDEV_TX_BUSY, so
the stack requeues the skb to try again later.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (25 commits)
powerpc: Fix config dependency problem with MPIC_U3_HT_IRQS
via-pmu: Add compat_pmu_ioctl
powerpc: Wire up fanotify_init, fanotify_mark, prlimit64 syscalls
powerpc/pci: Fix checking for child bridges in PCI code.
powerpc: Fix typo in uImage target
powerpc: Initialise paca->kstack before early_setup_secondary
powerpc: Fix bogus it_blocksize in VIO iommu code
powerpc: Inline ppc64_runlatch_off
powerpc: Correct smt_enabled=X boot option for > 2 threads per core
powerpc: Silence xics_migrate_irqs_away() during cpu offline
powerpc: Silence __cpu_up() under normal operation
powerpc: Re-enable preemption before cpu_die()
powerpc/pci: Drop unnecessary null test
powerpc/powermac: Drop unnecessary null test
powerpc/powermac: Drop unnecessary of_node_put
powerpc/kdump: Stop all other CPUs before running crash handlers
powerpc/mm: Fix vsid_scrample typo
powerpc: Use is_32bit_task() helper to test 32 bit binary
powerpc: Export memstart_addr and kernstart_addr on ppc64
powerpc: Make rwsem use "long" type
...
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty-2.6:
68328serial: check return value of copy_*_user() instead of access_ok()
synclink: add mutex_unlock() on error path
rocket: add a mutex_unlock()
ip2: return -EFAULT on copy_to_user errors
ip2: remove unneeded NULL check
serial: print early console device address in hex
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core-2.6:
kobject_uevent: fix typo in comments
firmware_class: fix typo in error path
kobject: Break the kobject namespace defs into their own header
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (29 commits)
ARM: imx: fix build failure concerning otg/ulpi
USB: ftdi_sio: add product ID for Lenz LI-USB
USB: adutux: fix misuse of return value of copy_to_user()
USB: iowarrior: fix misuse of return value of copy_to_user()
USB: xHCI: update ring dequeue pointer when process missed tds
USB: xhci: Remove buggy assignment in next_trb()
USB: ftdi_sio: Add ID for Ionics PlugComputer
USB: serial: io_ti.c: don't return 0 if writing the download record failed
USB: otg: twl4030: fix wrong assumption of starting state
USB: gadget: Return -ENOMEM on memory allocation failure
USB: gadget: fix composite kernel-doc warnings
USB: ssu100: set tty_flags in ssu100_process_packet
USB: ssu100: add disconnect function for ssu100
USB: serial: export symbol usb_serial_generic_disconnect
USB: ssu100: rework logic for TIOCMIWAIT
USB: ssu100: add register parameter to ssu100_setregister
USB: ssu100: remove duplicate #defines in ssu100
USB: ssu100: refine process_packet in ssu100
USB: ssu100: add locking for port private data in ssu100
USB: r8a66597-udc: return -ENOMEM if kzalloc() fails
...
The ioctls are actually compatible, but due to historical mistake the
numbers differ between 32bit and 64bit.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Add ftdi product ID for Lenz LI-USB, a model train interface. This
was NOT tested against 2.6.35, but a similar patch was tested with the
CentOS 2.6.18-194.11.1.el5 kernel. It wasn't clear to me what
ordering is being used in ftdi_sio.c, so I inserted the ID after another
model train entry(SPROG_II).
Signed-off-by: Galen Seitz <galens@seitzassoc.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns number of not copied bytes, not error code.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes a isoc transfer bug reported by Sander Eikelenboom.
When ep->skip is set, endpoint ring dequeue pointer should be updated
when processed every missed td. Although ring dequeue pointer will also
be updated when ep->skip is clear, leave it intact during missed tds
processing may cause two issues:
1). If the very next valid transfer following missed tds is a short
transfer, its actual_length will be miscalculated;
2). If there are too many missed tds during transfer, new inserted tds
may found the transfer ring full and urb enqueue fails.
Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Sander Eikelenboom <linux@eikelenboom.it>
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The code to increment the TRB pointer has a slight ambiguity that could
lead to a bug on different compilers. The ANSI C specification does not
specify the precedence of the assignment operator over the postfix
operator. gcc 4.4 produced the correct code (increment the pointer and
assign the value), but a MIPS compiler that one of John's clients used
assigned the old (unincremented) value.
Remove the unnecessary assignment to make all compilers produce the
correct assembly.
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add the ID for the Ionics PlugComputer (<http://ionicsplug.com/>).
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If the write download record failed we shouldn't return 0.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The reset state of twl4030-usb is not sleeping, it starts
up awaken and we need to disable it if we have booted
with a disconnected cable to avoid over consumption on
the default state.
To avoid problems later, we read the current state of the
transceiver from the PHY_PWR_CTRL register. The bootloader
can, anyways, put the device to sleep before us.
Tested on a custom OMAP board.
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In this code, 0 is returned on memory allocation failure, even though other
failures return -ENOMEM or other similar values.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression ret;
expression x,e1,e2,e3;
@@
ret = 0
... when != ret = e1
*x = \(kmalloc\|kcalloc\|kzalloc\)(...)
... when != ret = e2
if (x == NULL) { ... when != ret = e3
return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Warning(include/linux/usb/composite.h:284): No description found for parameter 'disconnect'
Warning(drivers/usb/gadget/composite.c:744): No description found for parameter 'c'
Warning(drivers/usb/gadget/composite.c:744): Excess function parameter 'cdev' description in 'usb_string_ids_n'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
flag was never set in ssu100_process_packet. Add logic to set it
before calling tty_insert_flip_*
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a disconnect function to the functions of this device. The
disconnect is a call to usb_serial_generic_disconnect() so it requires
that symbol to be exported from generic.c.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is needed by the ssu100 driver to use this function.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Rework the logic for TIOCMIWAIT to use wait_event_interruptible.
This also adds support for TIOCGICOUNT.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The function ssu100_setregister was hard coded to only set the MCR
register. Add a register parameter so that other registers can be
set.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ssu100 uses a TI16C550C UART so the SERIAL_ defines in this code
are duplicates of those found in serial_reg.h. Remove the defines in
ssu100.c and use the ones in the header file.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The status information does not appear at the start of each incoming
packet so the check for len < 4 at the start of ssu100_process_packet
is wrong. Remove it.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If we can't read the firmware for a device from the disk, and yet the
device already has a valid firmware image in it, we don't want to
replace the firmware with something invalid. So check the version
number to be less than the current one to verify this is the correct
thing to do.
Reported-by: Chris Beauchamp <chris@chillibean.tv>
Tested-by: Chris Beauchamp <chris@chillibean.tv>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB max packet size (always little-endian) was not being byte
swapped on big-endian systems.
Applicable since [USB: ftdi_sio: fix hi-speed device packet size calculation] approx 2.6.31
Signed-off-by: Michael Wileczka <mikewileczka@yahoo.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The definitions for BREAK_ON and BREAK_OFF are inverted, causing break
requests to fail. This patch sets BREAK_ON and BREAK_OFF to the correct
values.
Signed-off-by: Craig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for the Zeagle N2iTiON3 dive computer interface. Since
Zeagle devices are actually manufactured by Seiko, this patch will
support other Seiko based models as well.
Signed-off-by: Jef Driesen <jefdriesen@telenet.be>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The patch with title below makes reference count of usb serial module
always more than one after driver is bound.
USB-BKL: Remove BKL use for usb serial driver probing
In fact, the patch above only replaces lock_kernel() with try_module_get()
, and does not use module_put() to do what unlock_kernel() did, so casue leak
of reference count of usb serial module and the module can not be unloaded
after serial driver is bound with device.
This patch fixes the issue, also simplifies such things:
-only call try_module_get() once in the entry of usb_serial_probe()
-only call module_put() once in the exit of usb_serial_probe
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Cc: Johan Hovold <jhovold@gmail.com>
Cc: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I recently bought a i-gotU USB GPS, and whilst hunting around for linux
support discovered this post by you back in 2009:
http://kerneltrap.org/mailarchive/linux-usb/2009/3/12/5148644
>Try the navman driver instead. You can either add the device id to the
> driver and rebuild it, or do this before you plug the device in:
> modprobe navman
> echo -n "0x0df7 0x0900" > /sys/bus/usb-serial/drivers/navman/new_id
>
> and then plug your device in and see if that works.
I can confirm that the navman driver works with the right device IDs on
my i-gotU GT-600, which has the same device IDs. Attached is a patch
adding the IDs.
From: Ross Burton <ross@linux.intel.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The ISP1760 has some timing requirements where it has to delay a short
period after a write to a register has started. However, this delay is
from the time the write hits the USB chip (the ISP1760), not from the
time where the processor started processing the write. So on a quick
enough processor, it is sometimes possible for the write to not hit the
device before we start delaying, and we then violate the part's timing
requirements, so things stop working.
To avoid all this, insert a write barrier after the register write and
before the timing delay/register read so we can guarantee we only start
counting time after the write has hit the device.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We're trying to test for the the end of the loop here. "format" is
never NULL. We don't know what "format->fcc" is because we're past the
end of the loop and I think "fmt->fmt.pix.pixelformat" comes from the
user so we don't know what that is either. It works, but it's cleaner
to just test to see if (i == ARRAY_SIZE(uvc_formats).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Function qlcnic_intr has pointer to qlcnic_host_sds_ring
as second parameter not pointer to qlcnic_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Function netxen_intr has pointer to nx_host_sds_ring
as second parameter not pointer to netxen_adapter.
Signed-off-by: Yinglin Luan <synmyth@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
netfilter: fix CONFIG_COMPAT support
isdn/avm: fix build when PCMCIA is not enabled
header: fix broken headers for user space
e1000e: don't check for alternate MAC addr on parts that don't support it
e1000e: disable ASPM L1 on 82573
ll_temac: Fix poll implementation
netxen: fix a race in netxen_nic_get_stats()
qlnic: fix a race in qlcnic_get_stats()
irda: fix a race in irlan_eth_xmit()
net: sh_eth: remove unused variable
netxen: update version 4.0.74
netxen: fix inconsistent lock state
vlan: Match underlying dev carrier on vlan add
ibmveth: Fix opps during MTU change on an active device
ehea: Fix synchronization between HW and SW send queue
bnx2x: Update bnx2x version to 1.52.53-4
bnx2x: Fix PHY locking problem
rds: fix a leak of kernel memory
netlink: fix compat recvmsg
netfilter: fix userspace header warning
...
* 'for-upstream/pvhvm' of git://xenbits.xensource.com/people/ianc/linux-2.6:
xen: pvhvm: make it clearer that XEN_UNPLUG_* define bits in a bitfield
xen: pvhvm: rename xen_emul_unplug=ignore to =unnnecessary
xen: pvhvm: allow user to request no emulated device unplug
* 'drm-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (33 commits)
drm/radeon/kms: fix typo in radeon_compute_pll_gain
drm/radeon/kms: try to detect tv vs monitor for underscan
drm/radeon/kms: fix sideport detection on newer rs880 boards
drm/radeon: fix passing wrong type to gem object create.
drm/radeon/kms: set encoder type to DVI for HDMI on evergreen
drm/radeon/kms: add back missing break in info ioctl
drm/radeon/kms: don't enable MSIs on AGP boards
drm/radeon/kms: fix agp mode setup on cards that use pcie bridges
drm: move dereference below check
drm: fix end of loop test
drm/radeon/kms: rework radeon_dp_detect() logic
drm/radeon/kms: add missing asic callback assignment for evergreen
drm/radeon/kms/DCE3+: switch pads to ddc mode when going i2c
drm/radeon/kms/pm: bail early if nothing's changing
drm/radeon/kms/atom: clean up dig atom handling
drm/radeon/kms: DCE3/4 transmitter fixes
drm/radeon/kms: rework encoder handling
drm/radeon/kms: DCE3/4 AdjustPixelPll updates
drm/radeon: Fix stack data leak
drm/radeon/kms: fix GTT/VRAM overlapping test
...
As copy_*_user() calls access_ok() it should not be called explicitly.
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is a path which still holds its mutex here.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This path needs a mutex_unlock(). This is stuff from the bkl to mutex
transition.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
copy_to_user() returns the number of bytes remaining but we want to return
a negative error code on errors.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: "Michael H. Warfield" <mhw@wittsend.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We don't pass NULL tty pointers to the close function, and anyway we
already dereferenced it at this point. This check can be removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Cc: "Michael H. Warfield" <mhw@wittsend.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Device addresses are usually printed in hex.
Signed-off-by: Tony Luck <tony.luck@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's currently stalled and the original submitter recommended that it
just be dropped at this point in time due.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Each net_device in a system will automatically managed as a possible
batman_if and holds different informations like a buffer with a prepared
originator messages. To reduce the memory usage, the packet_buff will
only be allocated when the interface is really added/enabled for
batman-adv.
The function to update the hw address information inside the packet_buff
just assumes that the packet_buff is always initialised and thus the
kernel will just oops when we try to change the hw address of a not
already fully enabled interface.
We must always check if the packet_buff is allocated before we try to
change information inside of it.
Reported-by: Tim Glaremin <Tim.Glaremin@web.de>
Reported-by: Kazuki Shimada <zukky@bb.banban.jp>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
dev_put allows a device to be freed when all its references are dropped.
After that we are not allowed to access that information anymore. Access
to the data structure of a net_device must be surrounded a dev_hold
and ended using dev_put.
batman-adv adds a device to its own management structure in
hardif_add_interface and will release it in hardif_remove_interface.
Thus it must hold a reference all the time between those functions to
prevent any access to the already released net_device structure.
Reported-by: Tim Glaremin <Tim.Glaremin@web.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We try to get all events for all net_devices to be able to add special
sysfs folders for the batman-adv configuration. This also includes such
events like NETDEV_POST_INIT which has no valid kobject according to
v2.6.32-rc3-13-g7ffbe3f. This would create an oops in that situation.
It is enough to create the batman_if only on NETDEV_REGISTER events
because we will also receive those events for devices which already
existed when we registered the notifier call.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Earlier batman-adv versions would only create a batman_if struct after
a corresponding interface had been activated by a user. Now each
existing system interface has a batman_if struct and has to be checked
by verifying the IF_ACTIVE flag.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When receiving an batman icmp echo request or in case of a time-to-live
exceeded batman would reply with the mac address of the outgoing
interface which might be a secondary interface. Because secondary
interfaces are not globally known this might lead to confusion.
Now, replies are sent with the mac address of the primary interface.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If a batman icmp packet had to be routed over a secondary interface
at the first hop, the mac address of that secondary interface would
be written in the 'orig' field of the icmp packet. A node which is
more than one hop away is not aware of the mac address because
secondary interfaces are not flooded through the whole mesh and
therefore can't send a reply.
This patch always sends the mac address of the primary interface
in the 'orig' field of the icmp packet.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The orig_hash_lock spinlock always has to be locked with IRQs being
disabled to avoid deadlocks between code that is being executed in
IRQ context and code that is being executed in non-IRQ context.
Reported-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Greg Kroah-Hartman merged Linus 2.6.36 tree in
e9563355ac with his staging tree.
Different parts of the merge conflicts were resolved incorrectly and may
result in an abnormal behavior.
Signed-off-by: Sven Eckelmann <sven.eckelmann@gmx.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a compile warning by initializaing lblk. Since FTL_Get_Block_Index()
returns BAD_BLOCK if it doesn't find the logical block number, lblk
number is initizalized to BAD_BLOCK.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a compile warning by removing an unused variable int i.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the first patch of a patchset that removes all compilations
warnings in staging/spectra.
These patches are a delta from a previous patchset and it assumes that
these three patches all already applied:
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Last patch has a style problem. Sending the correct one. Sorry for the noise
Since BKL was removed from block ioctl handling code, locked_ioctl doesn't
exist anymore.
Using ioctl instead and doing the locking manually.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
REQ_TYPE_LINUX_BLOCK and REQ_LB_OP_FLUSH doesn't exist anymore. Using
the new REQ_FLUSH flag instead
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch is the first one of a patchset that allows
stagin/spectra driver to compile in linux-next.
blk_queue_ordered doesn't receive a prepare flush function anymore
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In the error path, _request_firmware sets
firmware_p to NULL rather than *firmware_p,
which leads to passing a freed firmware
struct to drivers when the firmware file
cannot be found. Fix this.
Broken by commit f8a4bd3456.
Reported-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The machines I have appear to provide their return value in the arguments
structure, not the output structure. Rework the driver to use that again
in order to get rfkill working again.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Don't ask how ACPI_TOSHIBA got enabled on in desktop system's .config -
I don't know. But it has silently been there until I tried 2.6.36-rc2,
where it broke the build because I don't have LED support turned on.
Attached patch fixes things up.
(I had to change BACKLIGHT_CLASS_DEVICE to "depends" because otherwise
I get unsightly core dumps out of scripts/kconfig/conf).
jon
--
toshiba: make sure we pull in LED support
The Toshiba extras driver uses the LED module, so make sure we have it
configure in.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Now that we have this API, switch the two in-kernel users to it.
Resolves an oops introduced by commit
1abec4fdbb.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
It is not immediately clear what this option causes to become
ignored. The actual meaning is that it is not necessary to unplug the
emulated devices to safely use the PV ones, even if the platform does
not support the unplug protocol. (pressumably the user will only add
this option if they have ensured that their domain configuration is
safe).
I think xen_emul_unplug=unnecessary better captures this.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: Stefano Stabellini <Stefano.Stabellini@eu.citrix.com>
Return of the bi_rw tests is no longer bool after commit 74450be1. But
results of such tests are stored in bools. This doesn't fit in there
for some compilers (gcc 4.5 here), so either use !! magic to get real
bools or use ulong where the result is assigned somewhere.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jeff Moyer <jmoyer@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
If kmalloc() fails then cleanup and return failure (-1).
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The doorbell reset initially appears to work correctly,
the controller resets, comes up, some i/o can even be
done, but on at least some Smart Arrays in some servers,
it eventually causes a subsequent controller lockup due
to some kind of PCIe error, and kdump can end up leaving
the root filesystem in an unbootable state. For this
reason, until the problem is fixed, or at least isolated
to certain hardware enough to be avoided, the doorbell
reset should not be used at all.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
* 'nouveau/for-airlied' of /ssd/git/drm-nouveau-next:
drm/nouveau: fix earlier mistake when fixing merge conflict
drm/nvc0: fix thinko in instmem suspend/resume
drm/nouveau: Workaround missing GPIO tables on an Apple iMac G4 NV18.
drm/nouveau: Add TV-out quirk for an MSI nForce2 IGP.
drm/nv50-nvc0: ramht_size is meant to be in bytes, not entries
drm/nouveau: punt some more log messages to debug level
drm/nouveau: remove warning about unknown tmds table revisions
drm/nouveau: check for error when allocating/mapping dummy page
drm/nouveau: fix race condition when under memory pressure
drm/nv50: fix minor thinko from nvc0 changes
drm/nouveau: Don't try DDC on the dummy I2C channel.
Looks like this got copied from the ddx wrong.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
When enabling underscan for hdmi monitors, attempt to detect
whether we are driving a TV or a monitor. The should hopefully
prevent underscan from being enabled on monitors attached via
hdmi that do not overscan the image. Only enable underscan
if the mode is a common hdtv mode (480p, 720p, etc.).
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The meaning of ucMemoryType changed on recent boards, however,
ulBootUpSidePortClock should be set properly across all boards.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
We are passing a ttm type when we want to pass true/false.
Reported-by: Dr. David Alan Gilbert <linux@treblig.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (58 commits)
drm/i915,intel_agp: Add support for Sandybridge D0
drm/i915: fix render pipe control notify on sandybridge
agp/intel: set 40-bit dma mask on Sandybridge
drm/i915: Remove the conflicting BUG_ON()
drm/i915/suspend: s/IS_IRONLAKE/HAS_PCH_SPLIT/
drm/i915/suspend: Flush register writes before busy-waiting.
i915: disable DAC on Ironlake also when doing CRT load detection.
drm/i915: wait for actual vblank, not just 20ms
drm/i915: make sure eDP PLL is enabled at the right time
drm/i915: fix VGA plane disable for Ironlake+
drm/i915: eDP mode set sequence corrections
drm/i915: add panel reset workaround
drm/i915: Enable RC6 on Ironlake.
drm/i915/sdvo: Only set is_lvds if we have a valid fixed mode.
drm/i915: Set up a render context on Ironlake
drm/i915 invalidate indirect state pointers at end of ring exec
drm/i915: Wake-up wait_request() from elapsed hang-check (v2)
drm/i915: Apply i830 errata for cursor alignment
drm/i915: Only update i845/i865 CURBASE when disabled (v2)
drm/i915: FBC is updated within set_base() so remove second call in mode_set()
...
This one is missed in last pipe control fix for sandybridge,
that really unmask interrupt bit for notify in render engine IMR.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
We now attempt to free "active" objects following a GPU hang as either
the GPU will be reset or the hang is permenant. In either case, the GPU
writes will not be flushed to main memory and it should be safe to
return that memory back to the system.
The BUG_ON(active) is thus overkill and can erroneously fire after a
EIO.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
For the shared paths on the next generation chipsets.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Like on Sandybridge, disabling the DAC here when doing CRT load detect
avoids forever hangs waiting on the hardware.
test procedure on HP 2740p:
boot with no VGA plugged in, start X,
plug in VGA monitor (1280x1024)
chvt 3
machine hangs waiting forever.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Waiting for a hard coded 20ms isn't always enough to make sure a vblank
period has actually occurred, so add code to make sure we really have
passed through a vblank period (or that the pipe is off when disabling).
This prevents problems with mode setting and link training, and seems to
fix a bug like https://bugs.freedesktop.org/show_bug.cgi?id=29278, but
on an HP 8440p instead. Hopefully also fixes
https://bugs.freedesktop.org/show_bug.cgi?id=29141.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
Recent modprobe and udev versions allow to create device nodes
for modules which are not loaded. Only the first access will cause
the in-kernel module loader to pull-in the module. Systems which
never access the device node will not needlessly load the module,
and no longer need init scripts or other facilities to unconditionally
load it.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Since handle_sysrq() does not take tty as argument anymore we can
drop it from usb_serial_handle_sysrq_char() as well.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sysrq operations do not accept tty argument anymore so no need to pass
it to us.
[Stephen Rothwell <sfr@canb.auug.org.au>: fix build breakage in drm code
caused by sysrq using bool but not including linux/types.h]
[Sachin Sant <sachinp@in.ibm.com>: fix build breakage in s390 keyboadr
driver]
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Apparently, the check for a 6-byte ID string introduced by commit
426c457a32 ("mtd: nand: extend NAND flash
detection to new MLC chips") is NOT sufficient to determine whether or
not a Samsung chip uses their new MLC detection scheme or the old,
standard scheme. This adds a condition to check cell type.
Signed-off-by: Tilman Sauerbeck <tilman@code-monkey.de>
Signed-off-by: Brian Norris <norris@broadcom.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
gcc-4.0.2:
drivers/scsi/qla4xxx/ql4_os.c: In function 'qla4_8xxx_error_recovery':
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2377: sorry, unimplemented: called from here
drivers/scsi/qla4xxx/ql4_glbl.h:135: sorry, unimplemented: inlining failed in call to 'qla4_8xxx_set_drv_active': function body not available
drivers/scsi/qla4xxx/ql4_os.c:2393: sorry, unimplemented: called from here
Cc: Ravi Anand <ravi.anand@qlogic.com>
Cc: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There's some merge problem between sdhic core and sdhci-s3c host. After
mutex is changed to spinlock. It needs to use use spin lock functions and
use the correct card detection function.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Some SDHCI controllers like s5pc110 don't have an HISPD bit in the HOSTCTL
register.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 7721fea3d0 ("hwmon:
f71882fg: add support for the Fintek F71808E").
Hans said:
: A second review after I've received a data sheet for this device from
: Fintek has turned up a few bugs.
:
: Unfortunately Giel (nor I) have time to fix this in time for the 2.6.36
: cycle. Therefor I would like to see this patch reverted as not having any
: support for the hwmon function of this superio chip is better then having
: unreliable support.
Cc: Giel van Schijndel <me@mortis.eu>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Screen is completely corrupted since 2.6.34. Bisection revealed that it's
caused by commit 6175ddf06b ("x86: Clean up mem*io functions.").
H. Peter Anvin explained that memcpy_toio() does not copy data in 32bit
chunks anymore on x86.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Petr Vandrovec <vandrove@vc.cvut.cz>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: <stable@kernel.org> [2.6.34.x, 2.6.35.x]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fixes the pink line that shows up with some hdmi monitors. This
will need to be revisited when audio support is added.
Fixes:
http://bugs.freedesktop.org/show_bug.cgi?id=27452
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Noone is using tty argument so let's get rid of it.
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This seems to have gotten lost in the hyper-z merge.
Noticed by legume on IRC.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Asics that use an AGP to PCIE bridge don't have the AGP_STATUS
register so just use whatever mode the host side setup.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: Jerome Glisse <glisse@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Bruce Allan <bruce.w.allan@intel.com>
The alternate MAC address feature is only supported by 80003ES2LAN and
82571 LOMs as well as a couple 82571 mezzanine cards. Checking for an
alternate MAC address on other parts can fail leading to the driver not
able to load. This patch limits the check for an alternate MAC address
to be done only for parts that support the feature.
This issue has been around since support for the feature was introduced
to the e1000e driver in 2.6.34.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Reported-by: Fabio Varesano <fax8@users.sourceforge.net>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
"fb_helper_conn" is dereferenced before the check for NULL. It's never
actually NULL here, so this is mostly to keep the static checkers happy.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
"agpmem" is never NULL here because it is the list cursor of a
list_for_each_entry() list.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the e1000-devel mailing list, Nils Faerber reported latency issues with
the 82573 LOM on a ThinkPad X60. It was found to be caused by ASPM L1;
disabling it resolves the latency. The issue is present in kernels back
to 2.6.34 and possibly 2.6.33.
Reported-by: Nils Faerber <nils.faerber@kernelconcepts.de>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the connector is eDP, it can only be DP, not TMDS.
Always set the detected sink type. If the sink is
detected as non-DP, but there is no EDID, you can still
manually force the port on. If the sink type is DP
and there's no DPCD, there's no way to force the monitor
on since you need both ends to train the link.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pins for ddc and aux are shared so you need to switch the
mode when doing ddc. The ProcessAuxChannel table already sets
the pin mode to DP. This should fix unreliable ddc issues
on DP ports using non-DP monitors.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
This allows the tables to be run in some additional cases
where the connector info isn't necessary.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- INIT action takes the actual connector type id, not the enum id
- some evergreen cards have the ENABLE_OUTPUT/DISABLE_OUTPUT actions
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On most newer asics, digital encoders have two links each
and they can be used independantly. As such, treat them as
separate encoders otherwise the individual links will not
get programmed properly at modeset time.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add options necessary bits for:
- SS on DP
- SS on LVDS
- set clocks right for DP
- deep color on hdmi (needs additional encoder and edid work as well)
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Always zero-init a structure on the stack which is returned by a
function. Otherwise you may leak random stack data from previous
function calls.
This fixes the following warning I was seeing:
CC [M] drivers/gpu/drm/radeon/radeon_atombios.o
drivers/gpu/drm/radeon/radeon_atombios.c: In function "radeon_atom_get_hpd_info_from_gpio":
drivers/gpu/drm/radeon/radeon_atombios.c:261: warning: "hpd.plugged_state" is used uninitialized in this function
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: David Airlie <airlied@linux.ie>
Cc: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
GTT/VRAM overlapping test had a typo which leaded to not
detecting case when vram_end > gtt_end. This patch fix the
logic and should fix#16574
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>
Because we might be in interrupt context, replace del_timer_sync() with
del_timer(). If the timer is already running, we know that it will
clean up the transaction, so we do not need to do any further processing
in the normal transaction handler.
Many thanks to Yong Zhang for diagnosing this.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The incoming request hander fwnet_receive_packet() expects subsequent
datagram handling code to return non-zero on errors. However, almost
none of the failure paths did so. Fix them all.
(This error reporting is used to send and RCODE_CONFLICT_ERROR to the
sender node in such failure cases. Two modes of failure exist: Out of
memory, or firewire-net is unaware of any peer node to which a fragment
or an ARP packet belongs. However, it is unclear whether a sender can
actually make use of such information. A Linux peer apparently can't.
Maybe it should all be simplified to void functions.)
Reported-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Fix I/O stalls with some 4-bay RAID enclosures which are based on
OXUF936QSE:
- Onnto dataTale RSM4QO, old firmware (not anymore with current
firmware),
- inXtron Hydra Super-S LCM, old as well as current firmware
when used in RAID-5 mode, perhaps also in other RAID modes.
The stalls happen during heavy or moderate disk traffic in periods that
are a multiple of 5 minutes, roughly twice per hour. They are caused
by the target responding too late to an ORB_Pointer register write:
The target responds after Split_Timeout, hence firewire-core cancels
the transaction, and firewire-sbp2 fails the SCSI request. The SCSI
core retries the request, that fails again (and again), hence SCSI core
calls firewire-sbp2's abort handler (and even the Management_Agent
register write in the abort handler has the transaction timeout
problem).
During all that, the process which issued the I/O is stalled in I/O
wait state.
Meanwhile, the target actually acts on the first failed SCSI request:
It responds to the ORB_Pointer write later (seen in the kernel log as
"firewire_core: Unsolicited response") and also finishes the SCSI
request with proper status (seen in the kernel log as "firewire_sbp2:
status write for unknown orb").
So let's just ignore RCODE_CANCELLED in the transaction callback and
wait for the target to complete the ORB nevertheless. This requires
a small modification is sbp2_cancel_orbs(); it now needs to call
orb->callback() regardless whether fw_cancel_transaction() found the
transaction unfinished or finished.
A different solution is to increase Split_Timeout on the local node.
(Tested: 2000ms timeout; maybe 1000ms or something like that works too.
200ms is insufficient. Standard is 100ms.) However, I rather not do
this because any software on any node could change the Split_Timeout to
something unsuitable. Or such a large Split_Timeout may be undesirable
for other purposes.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
When an ORB was canceled (Command ORB i.e. SCSI request timed out, or
Management ORB timed out), or there was a send error in the initial
transaction, we missed to drop one of the ORB's references and thus
leaked memory.
Background:
In total, we hold 3 references to each Operation Request Block:
- 1 during sbp2_scsi_queuecommand() or sbp2_send_management_orb()
respectively,
- 1 for the duration of the write transaction to the ORB_Pointer or
Management_Agent register of the target,
- 1 for as long as the ORB stays within the lu->orb_list, until
the ORB is unlinked from the list and the orb->callback was
executed.
The latter one of these 3 references is finished
- normally by sbp2_status_write() when the target wrote status
for a pending ORB,
- or by sbp2_cancel_orbs() in case of an ORB time-out,
- or by complete_transaction() in case of a send error.
Of them, the latter two lacked the kref_put.
Add the missing kref_put()s. Add comments to the gets and puts of
references for transaction callbacks and ORB callbacks so that it is
easier to see what is supposed to happen.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Commit c7b28e25cb ("mtd: nand: refactor BB
marker detection") caused a regression in detection of factory-set bad
block markers, especially for certain small-page NAND. This fix removes
some unneeded constraints on using NAND_SMALL_BADBLOCK_POS, making the
detection code more correct.
This regression can be seen, for example, in Hynix HY27US081G1M and
similar.
Signed-off-by: Brian Norris <norris@broadcom.com>
Tested-by: Michael Guntsche <mike@it-loops.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Functions ll_temac_rx_irq and ll_temac_tx_irq
have pointer to net_device as second parameter not
pointer to temac_local.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Dont clear netdev->stats, it might give transient wrong values to
concurrent stat readers.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Spin lock rds_ring->lock is used in poll routine, so other users should
use spin_lock_bh(). While posting rx buffers from netxen_nic_attach,
rds_ring->lock is not required, so cleaning it instead of fixing it by
spin_lock_bh().
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ehea: Fix synchronization between HW and SW send queue
When memory is added to / removed from a partition via the Memory DLPAR
mechanism, the eHEA driver has to do a couple of things to reflect the
memory change in its own IO address translation tables. This involves
stopping and restarting the HW queues.
During this operation, it is possible that HW and SW pointer into these
queues get out of sync. This results in a situation where packets that
are attached to a send queue are not transmitted immediately, but
delayed until further X packets have been put on the queue.
This patch detects such loss of synchronization, and resets the ehea
port when needed.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Update bnx2x version to 1.52.53-4
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
PHY locking is required between two ports for some external PHYs. Since
initialization was done in the common init function (called only on the
first port initialization) rather than in the port init function, there
was in fact no PHY locking between the ports.
Signed-off-by: Yaniv Rosner <yanivr@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
USB HID: Add ID for eGalax Multitouch used in JooJoo tablet
HID: hiddev: fix memory corruption due to invalid intfdata
HID: hiddev: protect against disconnect/NULL-dereference race
HID: picolcd: correct ordering of framebuffer freeing
HID: picolcd: testing the wrong variable
For 5000 series of devices, use long monitor timer to check
stuck tx queues.
This modification apply to all the 5000 series including 5300 and others.
Cc: stable@kernel.org [2.6.35]
Reported-by: drago01 <drago01@gmail.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit c96c31e499
"(drivers/net/wireless: Use wiphy_<level>)"
inadvertently changed some upper case words to
lower case. Restore the original case.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We need to make sure the eDP PLL is enabled before the pipes or planes,
so do it as part of the DP prepare mode set function.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We need to use I/O port instructions to access VGA registers on
Ironlake+, and it doesn't hurt on other platforms, so switch the VGA
plane disable function over to using them. Move it to init time as well
while we're at it, no need to repeatedly disable the VGA plane with
every mode set and DPMS event.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
We should disable the panel first when shutting down an eDP link. And
when turning one on, the panel needs to be enabled before link training
or eDP I/O won't be enabled.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Ironlake requires that we clear the reset panel bit during power
sequences and restore it afterwards. Uncondtionally add code to do that
since it should be harmless on SNB+.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
fs: brlock vfsmount_lock
fs: scale files_lock
lglock: introduce special lglock and brlock spin locks
tty: fix fu_list abuse
fs: cleanup files_lock locking
fs: remove extra lookup in __lookup_hash
fs: fs_struct rwlock to spinlock
apparmor: use task path helpers
fs: dentry allocation consolidation
fs: fix do_lookup false negative
mbcache: Limit the maximum number of cache entries
hostfs ->follow_link() braino
hostfs: dumb (and usually harmless) tpyo - strncpy instead of strlcpy
remove SWRITE* I/O types
kill BH_Ordered flag
vfs: update ctime when changing the file's permission by setfacl
cramfs: only unlock new inodes
fix reiserfs_evict_inode end_writeback second call
This fixes a build breakage introduced by commit 4c2ef25fe0 ("mmc: fix
all hangs related to mmc/sd card insert/removal during suspend/resume")
Cc: David Brownell <david-b@pacbell.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-mmc@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Maxim Levitsky <maximlevitsky@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68knommu: include sched.h in ColdFire/SPI driver
m68knommu: formatting of pointers in printk()
m68knommu: arch/m68k/include/asm/ide.h fix for nommu
* 'for-linus' of git://neil.brown.name/md:
md raid-1/10 Fix bio_rw bit manipulations again
md: provide appropriate return value for spare_active functions.
md: Notify sysfs when RAID1/5/10 disk is In_sync.
Update recovery_offset even when external metadata is used.
* 'merge-devicetree' of git://git.secretlab.ca/git/linux-2.6:
spi.h: missing kernel-doc notation, please fix
of: fix missing headers for of_address_to_resource() in MTD and SysACE drivers
of: Fix missing includes
ata: update for of_device to platform_device replacement
microblaze: Fix of: eliminate of_device->node and dev_archdata->{of,prom}_node
microblaze: Fix of/address: Merge all of the bus translation code
booting-without-of: Remove nonexistent chapters from TOC, fix numbering
tty: fix fu_list abuse
tty code abuses fu_list, which causes a bug in remount,ro handling.
If a tty device node is opened on a filesystem, then the last link to the inode
removed, the filesystem will be allowed to be remounted readonly. This is
because fs_may_remount_ro does not find the 0 link tty inode on the file sb
list (because the tty code incorrectly removed it to use for its own purpose).
This can result in a filesystem with errors after it is marked "clean".
Taking idea from Christoph's initial patch, allocate a tty private struct
at file->private_data and put our required list fields in there, linking
file and tty. This makes tty nodes behave the same way as other device nodes
and avoid meddling with the vfs, and avoids this bug.
The error handling is not trivial in the tty code, so for this bugfix, I take
the simple approach of using __GFP_NOFAIL and don't worry about memory errors.
This is not a problem because our allocator doesn't fail small allocs as a rule
anyway. So proper error handling is left as an exercise for tty hackers.
[ Arguably filesystem's device inode would ideally be divorced from the
driver's pseudo inode when it is opened, but in practice it's not clear whether
that will ever be worth implementing. ]
Cc: linux-kernel@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: cleanup files_lock locking
Lock tty_files with a new spinlock, tty_files_lock; provide helpers to
manipulate the per-sb files list; unexport the files_lock spinlock.
Cc: linux-kernel@vger.kernel.org
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Acked-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
fs: fs_struct rwlock to spinlock
struct fs_struct.lock is an rwlock with the read-side used to protect root and
pwd members while taking references to them. Taking a reference to a path
typically requires just 2 atomic ops, so the critical section is very small.
Parallel read-side operations would have cacheline contention on the lock, the
dentry, and the vfsmount cachelines, so the rwlock is unlikely to ever give a
real parallelism increase.
Replace it with a spinlock to avoid one or two atomic operations in typical
path lookup fastpath.
Signed-off-by: Nick Piggin <npiggin@kernel.dk>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Test on a PXA310 platform with Samsung K9F2G08X0B NAND flash,
with tCH=5 and clk is 156MHz, ns2cycle(5, 156000000) returns -1.
ns2cycle returns negtive value will break NDTR0_tXX macros.
After checking the commit log, I found the problem is introduced by
commit 5b0d4d7c8a
"[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accurately"
To get num of clock cycles, we use below equation:
num of clock cycles = time (ns) / one clock cycle (ns) + 1
We need to add 1 cycle here because integer division will truncate the result.
It is possible the developers set the Min values in SPEC for timing settings.
Thus the truncate may cause problem, and it is safe to add an extra cycle here.
The various fields in NDTR{01} are in units of clock ticks minus one,
thus we should subtract 1 cycle then.
Thus the correct equation should be:
num of clock cycles = time (ns) / one clock cycle (ns) + 1 - 1
= time (ns) / one clock cycle (ns)
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Lei Wen <leiwen@marvell.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: stable@kernel.org
commit 7b6d91daee changed the behaviour
of a few variables in raid1 and raid10 from flags to bit-sets, but
left them as type 'bool' so they did not work.
Change them (back) to unsigned long.
(historical note: see 1ef04fefe2)
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: Jiri Slaby <jslaby@suse.cz> and many others
Using the coldfire qspi driver, I get the following error:
drivers/spi/coldfire_qspi.c: In function 'mcfqspi_irq_handler':
drivers/spi/coldfire_qspi.c:166: error: 'TASK_NORMAL' undeclared (first use in this function)
drivers/spi/coldfire_qspi.c:166: error: (Each undeclared identifier is reported only once
It is solved by adding the following include to coldfire_sqpi.c:
#include <linux/sched.h>
Fix suggested by Jate Sujjavanich <jsujjavanich@syntech-fuelmaster.com>
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
md_check_recovery expects ->spare_active to return 'true' if any
spares were activated, but none of them do, so the consequent change
in 'degraded' is not notified through sysfs.
So count the number of spares activated, subtract it from 'degraded'
just once, and return it.
Reported-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When RAID1 is done syncing disks, it'll update the state
of synced rdevs to In_sync. But it neglected to notify
sysfs that the attribute changed. So any programs that
are waiting for an rdev's state to change will not be
woken.
(raid5/raid10 added by neilb)
Signed-off-by: Adrian Drzewiecki <adriand@vmware.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The update of ->recovery_offset in sync_sbs is appropriate even then external
metadata is in use. However sync_sbs is only called when native
metadata is used.
So move that update in to the top of md_update_sb (which is the only
caller of sync_sbs) before the test on ->external.
This moves the update out of ->write_lock protection, but those fields
only need ->reconfig_mutex protection which they still have.
Also move the test on ->persistent up to where ->external is set as
for metadata update purposes they are the same.
Clear MD_CHANGE_DEVS and MD_CHANGE_CLEAN as they can only be confusing
if ->external is set or ->persistent isn't.
Finally move the update of ->utime down as it is only relevent (like
the ->events update) for native metadata.
Signed-off-by: NeilBrown <neilb@suse.de>
Reported-by: "Kwolek, Adam" <adam.kwolek@intel.com>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
vt,console,kdb: preserve console_blanked while in kdb
vt: fix regression warnings from KMS merge
arm,kgdb: fix GDB_MAX_REGS no longer used
kgdb: add missing __percpu markup in arch/x86/kernel/kgdb.c
kdb: fix compile error without CONFIG_KALLSYMS
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86:
platform/x86: move rfkill for Dell Mini 1012 to compal-laptop
thinkpad-acpi: Add KEY_CAMERA (Fn-F6) for Lenovo keyboards
thinkpad-acpi: add support for model-specific keymaps
thinkpad-acpi: lock down size of hotkey keymap
thinkpad-acpi: untangle ACPI/vendor backlight selection
thinkpad-acpi: find ACPI video device by synthetic HID
intel_ips: potential null dereference
drivers/platform/x86: Adjust confusing if indentation
x86: intel_ips: do not use PCI resources before pci_enable_device()
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Fix atomic64_t routine return values.
sparc64: Fix rwsem constant bug leading to hangs.
sparc: Hook up new fanotify and prlimit64 syscalls.
sparc: Really fix "console=" for serial consoles.
* master.kernel.org:/home/rmk/linux-2.6-arm:
VIDEO: amba clcd: don't disable an already disabled clock
ARM: Tighten check for allowable CPSR values
ARM: 6329/1: wire up sys_accept4() on ARM
ARM: 6328/1: Build with -fno-dwarf2-cfi-asm
ARM: 6326/1: kgdb: fix GDB_MAX_REGS no longer used
Fix the clock enable/disable tracking in the AMBA CLCD driver so
that the driver doesn't try to disable an already disabled clock,
thereby causing the clock (if shared) to become unbalanced.
This resolves a problem with CLCD on LPC32xx ARM platforms.
Reported-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The drivers for Xilinx' SystemACE and physically mapped MTDs were missing
prototypes for of_address_to_resource(). This patch adds the necessary
headers.
Signed-off-by: Graeme Smecher <graeme.smecher@mail.mcgill.ca>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Applying the filter flags directly as done since
commit 3474ad635d
Author: Johannes Berg <johannes.berg@intel.com>
Date: Thu Apr 29 04:43:05 2010 -0700
iwlwifi: apply filter flags directly
broke 3945 under some unknown circumstances, as
reported by Alex.
Since I want to keep the direct application of
filter flags on iwlagn, duplicate the code into
both 3945 and agn and remove committing the
RXON that broke things from the 3945 version.
Cc: stable@kernel.org [2.6.35]
Reported-by: Alex Romosan <romosan@sycorax.lbl.gov>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes missing includes from a number of .c files because
the code (wrongfully) depended on prom.h including them. The include
of linux/of_address.h was removed in microblaze prom.h in commit
"of/address: Clean up function declarations" (sha1 id 22ae782f8), but
not fixed in some callers. This patch fixes them up.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
With the current screwed but its ABI, ioctls for the drm, Linus pointed out that we could allow userspace to specify the allocation size, but we pass it to the driver which then uses it blindly to store a struct. Now if userspace specifies the allocation size as smaller than the driver needs, the driver can possibly overwrite memory.
This patch restructures the driver ioctls so we store the structure size we are expecting, and make sure we allocate at least that size. The copy from/to userspace are still restricted to the size the user specifies, this allows ioctl structs to grow on both sides of the equation.
Up until now we didn't really use the DRM_IOCTL defines in the kernel, so this cleans them up and adds them for nouveau.
v2:
fix nouveau pushbuf arg (thanks to Ben for pointing it out)
Reported-by: Linus Torvalds <torvalds@linuxfoundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
non-critical issue, CVE-2010-2803
Userspace controls the amount of memory to be allocate, so it can
get the ioctl to allocate more memory than the kernel uses, and get
access to kernel stack. This can only be done for processes authenticated
to the X server for DRI access, and if the user has DRI access.
Fix is to just memset the data to 0 if the user doesn't copy into
it in the first place.
Reported-by: Kees Cook <kees@ubuntu.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This should fix the reported TV-out load detection false positives
(fdo bug 29455).
Reported-by: Vlado Plaga <rechner@vlado-do.de>
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
The blob also thinks there's a TV connected, so hardware bug...
Signed-off-by: Francisco Jerez <currojerez@riseup.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
This message is apparently confusing people, and is being blamed for some
modesetting issues. Lets remove the message, and instead replace it
with an unconditional printout of the table revision.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
When VRAM is running out it's possible that the client's push buffers get
evicted to main memory. When they're validated back in, the GPU may
be used for the copy back to VRAM, but the existing synchronisation code
only deals with inter-channel sync, not sync between PFIFO and PGRAPH on
the same channel. This leads to PFIFO fetching from command buffers that
haven't quite been copied by PGRAPH yet.
This patch marks push buffers as so, and forces any GPU-assisted buffer
moves to be done on a different channel, which triggers the correct
synchronisation to happen before we submit them.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Commit b45cfba4e9 (vt,console,kdb:
implement atomic console enter/leave functions) introduced the ability
to atomically change the console mode with kernel mode setting but did
not preserve the state of the console_blanked variable.
The console_blanked variable must be restored when executing the
con_debug_leave() or further kernel mode set changes (such as using
chvt X) will fail to correctly set the state of console.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Andrew Morton <akpm@linux-foundation.org>
Fix the following new sparse warnings in vt.c introduced by the commit
b45cfba4e9 (vt,console,kdb: implement
atomic console enter/leave functions):
drivers/char/vt.c:197:5: warning: symbol 'saved_fg_console' was not declared. Should it be static?
drivers/char/vt.c:198:5: warning: symbol 'saved_last_console' was not declared. Should it be static?
drivers/char/vt.c:199:5: warning: symbol 'saved_want_console' was not declared. Should it be static?
drivers/char/vt.c:200:5: warning: symbol 'saved_vc_mode' was not declared. Should it be static?
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
CC: Andrew Morton <akpm@linux-foundation.org>
If a video head and keyboard are hooked up, specifying "console=ttyS0"
or similar to use a serial console will not work properly.
The key issue is that we must register all serial console capable
devices with register_console(), otherwise the command line specified
device won't be found. The sun serial drivers would only register
themselves as console devices if the OpenFirmware specified console
device node matched. To fix this part we now unconditionally get
the serial console register by setting serial_drv->cons always.
Secondarily we must not add_preferred_console() using the firmware
provided console setting if the user gaven an override on the kernel
command line using "console=" The "primary framebuffer" matching
logic was always triggering o n openfirmware device node match, make
it not when a command line override was given.
Reported-by: Frans Pop <elendil@planet.nl>
Tested-by: Frans Pop <elendil@planet.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like others in the Mini series, the Dell Mini 1012 does not support
the smbios hook required by dell-laptop.
Signed-off-by: Victor van den Elzen <victor.vde@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
On the T410s and most likely other current models, Fn-F6 is labeled as
Camera/Headphone key. Report key presses as KEY_CAMERA.
Signed-off-by: Jens Taprogge <jens.taprogge@taprogge.org>
Acked-by: Jerone Young <jerone.young@canonical.com>
Acked-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Use the quirks engine to select model-specific keymaps, which makes
it much easier to extend should we need it.
Keycodes are based on the tables at
http://www.thinkwiki.org/wiki/Default_meanings_of_special_keys.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Use a safer coding style for the hotkey keymap. This does not fix any
problems, as the current code is correct. But it might help avoid
mistakes in the future.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
acpi_video_backlight_support() already tells us if ACPI is handling
backlight control through the generic ACPI handle. It is better to just
trust it.
While at it, adjust down a printk priority, and test earlier for
brightness_enable=0.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The Linux ACPI core locates the ACPI video devices for us and marks them
with ACPI_VIDEO_HID. Use that information to locate the video device
instead of a half-baked hunt for _BCL.
This uncouples the detection of the number of backlight brightness
levels on ThinkPads from the ACPI paths in vid_handle.
With this change, the driver should be able to always detect whether the
ThinkPad uses a 8-level or 16-level brightness scale even on newer
models for which the vid_handle paths have not been updated yet.
It will skip deactivated devices in the ACPI device tree, which is a
change in behaviour.
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
There is a potential NULL dereference of "limits." We can just return
NULL earlier to avoid it. The caller already handles NULL returns.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The assignment of ret to -EIO appears to only make sense if the branch that
it is aligned with is executed, so move it into that branch.
The semantic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r disable braces4@
position p1,p2;
statement S1,S2;
@@
(
if (...) { ... }
|
if (...) S1@p1 S2@p2
)
@script:python@
p1 << r.p1;
p2 << r.p2;
@@
if (p1[0].column == p2[0].column):
cocci.print_main("branch",p1)
cocci.print_secs("after",p2)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
The JooJoo tablet (http://thejoojoo.com/) contains an "eGalax Inc. USB
TouchController", and this patch hooks it up to the egalax-touch driver.
Without the patch we don't get any cursor motion, since it comes through
Z/RX rather than X/Y.
(The egalax-touch driver does not yet generate a correct event sequence
for the "serial" protocol used by this device, though -- see the note
added to the code, which comes from research by Stéphane Chatty.)
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Stéphane Chatty <chatty@enac.fr>
Signed-off-by: Chris Ball <cjb@laptop.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6:
gcc-4.6: ACPI: fix unused but set variables in ACPI
ACPI thermal: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI video: make procfs I/F depend on CONFIG_ACPI_PROCFS
ACPI processor: remove deprecated ACPI procfs I/F
ACPI power_resource: remove unused procfs I/F
ACPI: remove deprecated ACPI procfs I/F
ACPI: introduce drivers/acpi/sysfs.c
ACPI: introduce module parameter acpi.aml_debug_output
ACPI: introduce drivers/acpi/debugfs.c
ACPI, APEI, ERST debug support
ACPI, APEI, Manage GHES as platform devices
ACPI, APEI, Rename CPER and GHES severity constants
ACPI, APEI, Fix a typo of error path of apei_resources_request
ACPI / ACPICA: Fix reference counting problems with GPE handlers
ACPI: Add the check of ADR flag in course of finding ACPI handle for PCI device
ACPI / Sleep: Drop acpi_suspend_finish()
ACPI / Sleep: Consolidate suspend and hibernation routines
ACPI / Wakeup: Simplify enabling of wakeup devices
ACPI / Sleep: Rework enabling wakeup devices
ACPI / Sleep: Free NVS copy if suspending of devices fails
Fixed up totally buggered "ACPI: fix unused but set variables in ACPI"
patch that doesn't even compile in the merge.
Thanks to Sedat Dilek <sedat.dilek@googlemail.com> for noticing the
breakage before I even pulled. And a big "Grrr.." at Len for not even
bothering to compile the tree before asking me to pull.
* git://git.infradead.org/mtd-2.6:
mtd/nand_ids: Fix buswidth
mtd/m25p80: fix test for end of loop
mtd/m25p80: retlen is never NULL
MIPS: Fix gen_nand probe structures contents
gen_nand: Test if nr_chips field is valid
BFIN: Fix gen_nand probe structures contents
nand/denali: move all hardware initialization work to denali_hw_init
nand/denali: Add a page check in denali_read_page & denali_read_page_raw
nand/denali: use cpu_relax() while waiting for hardware interrupt
nand/denali: change read_status function method
nand/denali: Fixed check patch warnings
ARM: Fix gen_nand probe structures contents
mtd/nand_base: fix kernel-doc warnings & typos
nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
nand/denali: Fixed handle ECC error bugs
nand/denali: use iowrite32() to replace denali_write32()
nand/denali: Fixed probe function bugs
* 'idle-release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-idle-2.6:
intel_idle: recognize Lincroft Atom Processor
intel_idle: no longer EXPERIMENTAL
intel_idle: disable module support
intel_idle: add support for Westmere-EX
intel_idle: delete power_policy modparam, and choose substate functions
intel_idle: delete substates DEBUG modparam
Some minor improvements in error handling, but overall it was mostly dead
code.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark the ACPI thermal procfs I/F deprecated, because /sys/class/thermal/
is already available and has been working for years w/o any problem.
The ACPI thermal procfs I/F will be removed in 2.6.37.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Mark ACPI video driver procfs I/F deprecated, including:
/proc/acpi/video/*/info
/proc/acpi/video/*/DOS
/proc/acpi/video/*/ROM
/proc/acpi/video/*/POST
/proc/acpi/video/*/POST_info
/proc/acpi/video/*/*/info
/proc/acpi/video/*/*/state
/proc/acpi/video/*/*/EDID
and
/proc/acpi/video/*/*/brightness, because
1. we already have the sysfs I/F /sysclass/backlight/ as the replacement
of /proc/acpi/video/*/*/brightness.
2. the other procfs I/F is not useful for userspace.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove deprecated ACPI processor procfs I/F, including:
/proc/acpi/processor/CPUX/power
/proc/acpi/processor/CPUX/limit
/proc/acpi/processor/CPUX/info
/proc/acpi/processor/CPUX/throttling still exists,
as we don't have sysfs I/F available for now.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rmove deprecated ACPI procfs I/F, including
/proc/acpi/debug_layer
/proc/acpi/debug_level
/proc/acpi/info
/proc/acpi/dsdt
/proc/acpi/fadt
/proc/acpi/sleep
because the sysfs I/F is already available
and has been working well for years.
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
