Commit Graph

18 Commits

Author SHA1 Message Date
Libin Yang
a1f17a872b USB: ohci: quirk AMD prefetch for USB 1.1 ISO transfer
The following patch in the driver is required to avoid USB 1.1 device
failures that may occur due to requests from USB OHCI controllers may
be overwritten if the latency for any pending request by the USB
controller is very long (in the range of milliseconds).

Signed-off-by: Libin Yang <libin.yang@amd.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-11-17 16:46:33 -08:00
Anand Gadiyar
4b26d50b33 trivial: OHCI: Fix typo in a comment
trivial: OHCI: Fix typo in a comment

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-09-21 15:14:51 +02:00
Libin Yang
ab1666c136 USB: quirk PLL power down mode
On some AMD 700 series southbridges, ISO OUT transfers (such as audio
playback through speakers) on the USB OHCI controller may be corrupted
when an A-Link express power saving feature is active.

PLL power down mode in conjunction with link power management feature
L1 being enabled is the bad combination ... this patch prevents them
from being enabled when ISO transfers are pending.

Signed-off-by: Crane Cai <crane.cai@amd.com>
Signed-off-by: Libin Yang <libin.yang@amd.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13 17:32:58 -07:00
Pete Zaitcev
6deb270b5c USB: ohci_hcd hang: submit vs. rmmod race
If we do rmmod ohci_hcd while an application is doing something, the
following may happen:

- a control URB completes (in finish_urb) and the ohci's endpoint is
  set into ED_UNLINK in ed_deschedule
- same URB is (re)submitted because of the open/close loop or other
  such application behaviour
- rmmod sets the state to HC_STATE_QUESCING
- finish_unlinks happens at next SOF; normally it would set ed into
  ED_IDLE and immediately call ed_schedule (since URB had extra TDs
  queued), which sets it into ED_OPER. But the check in ed_schedule
  makes it fail with -EAGAIN (which is ignored)
- from now on we have a dead URB stuck; it cannot even be unlinked
  because the ed status is not ED_OPER, and thus start_ed_unlink is
  not invoked.

This patch removes the check. In 2.6.25, all callers check for
__ACTIVE bit before invoking ed_schedule, which is more appropriate.

Alan Stern and David Brownell approved of this (cautiously).

Signed-off-by: Pete Zaitcev <zaitcev@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-21 15:16:25 -07:00
David Brownell
29c8f6a727 USB: ohci - record data toggle after unlink
This patch fixes a problem with OHCI where canceling bulk or
interrupt URBs may lose track of the right data toggle.  This
seems to be a longstanding bug, possibly dating back to the
Linux 2.4 kernel, which stayed hidden because

 (a) about half the time the data toggle bit was correct;
 (b) canceling such URBs is unusual; and
 (c) the few drivers which cancel these URBs either
      [1] do it only as part of shutting down, or
      [2] have fault recovery logic, which recovers.

For those transfer types, the toggle is normally written back
into the ED when each TD is retired.  But canceling bypasses
the mechanism used to retire TDs ... so on average, half the
time the toggle bit will be invalid after cancelation.

The fix is simple:  the toggle state of any canceled TDs are
propagated back to the ED in the finish_unlinks function.

(Issue found by leonidv11@gmail.com ...)

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Leonid <leonidv11@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-07-03 18:20:36 -07:00
Richard Kennedy
9cebcdc7fb USB: ohci: fix 2 timers to fire at jiffies + 1s
Code inspection discovered in 2 places timers were being incorrectly setup
using round_jiffies_relative(HZ).  The timer would then fire at time (0 <= T <
HZ).

Fix them to use round_jiffies(jiffies + HZ);

Signed-off-by: Richard Kennedy <richard@rsk.demon.co.uk>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: David Brownell <david-b@pacbell.net>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-04-02 15:06:09 -07:00
Alan Stern
4a00027dcb USB: Eliminate urb->status usage!
This patch (as979) removes the last vestiges of urb->status from the
host controller drivers and the root-hub emulator.  Now the field
doesn't get set until just before the URB's completion routine is
called.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:23 -07:00
Alan Stern
55d8496837 USB: reorganize urb->status use in ohci-hcd
This patch (as975) reorganizes the way ohci-hcd sets urb->status.  It
now keeps the information in a local variable until the last moment.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:21 -07:00
Alan Stern
6e8fe43b26 USB: avoid the donelist after an error in ohci-hcd
This patch (as972) changes ohci-hcd so that after an error occurs, the
remaining TDs for the URB will be skipped over entirely instead of
going through the donelist.  This enables the driver to give back the
URB as soon as the error is detected, avoiding the need to store the
error status in urb->status.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:19 -07:00
Alan Stern
eb23105462 USB: add urb->unlinked field
This patch (as970) adds a new urb->unlinked field, which is used to
store the status of unlinked URBs since we can't use urb->status for
that purpose any more.  To help simplify the HCDs, usbcore will check
urb->unlinked before calling the completion handler; if the value is
set it will automatically override the status reported by the HCD.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:19 -07:00
Alan Stern
b0d9efba3e USB: centralize -EREMOTEIO handling
This patch (as969) continues the ongoing changes to the way HCDs
report URB statuses.  The programming interface has been simplified by
making usbcore responsible for clearing urb->hcpriv and for setting
-EREMOTEIO status when an URB with the URB_SHORT_NOT_OK flag ends up
as a short transfer.

By moving the work out of the HCDs, this removes a fair amount of
repeated code.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:19 -07:00
Alan Stern
e9df41c5c5 USB: make HCDs responsible for managing endpoint queues
This patch (as954) implements a suggestion of David Brownell's.  Now
the host controller drivers are responsible for linking and unlinking
URBs to/from their endpoint queues.  This eliminates the possiblity of
strange situations where usbcore thinks an URB is linked but the HCD
thinks it isn't.  It also means HCDs no longer have to check for URBs
being dequeued before they were fully enqueued.

In addition to the core changes, this requires changing every host
controller driver and the root-hub URB handler.  For the most part the
required changes are fairly small; drivers have to call
usb_hcd_link_urb_to_ep() in their urb_enqueue method,
usb_hcd_check_unlink_urb() in their urb_dequeue method, and
usb_hcd_unlink_urb_from_ep() before giving URBs back.  A few HCDs make
matters more complicated by the way they split up the flow of control.

In addition some method interfaces get changed.  The endpoint argument
for urb_enqueue is now redundant so it is removed.  The unlink status
is required by usb_hcd_check_unlink_urb(), so it has been added to
urb_dequeue.

Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
CC: Olav Kongas <ok@artecdesign.ee>
CC: Tony Olech <tony.olech@elandigitalsystems.com>
CC: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:55:10 -07:00
Mike Nuss
89a0fd18a9 USB: OHCI handles more ZFMicro quirks
The ZF Micro OHCI controller exhibits unexpected behavior that seems to be
related to high load.  Under certain conditions, the controller will
complete a TD, remove it from the endpoint's queue, and fail to add it to
the donelist. This causes the endpoint to appear to stop responding. Worse,
if the device is removed while in that state, OHCI will hang while waiting
for the orphaned TD to complete.  The situation is not recoverable without
rebooting.

This fix enhances the scope of the existing OHCI_QUIRK_ZFMICRO flag:

 1. A watchdog routine periodically scans the OHCI structures to check
    for orphaned TDs. In these cases the TD is taken back from the
    controller and completed normally.

 2. If a device is removed while the endpoint is hung but before the
    watchdog catches the situation, any outstanding TDs are taken back
    from the controller in the 'sanitize' phase.

The ohci-hcd driver used to print "INTR_SF lossage" in this situation;
this changes it to the universally accurate "ED unlink timeout".  Other
instances of this message presumably have different root causes.

Both this Compaq quirk and a NEC quirk are now properly compiled out for
non-PCI builds of this driver.

Signed-off-by: Mike Nuss <mike@terascala.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-10-12 14:54:59 -07:00
David Brownell
dd9048af41 USB: ohci whitespace/comment fixups
This is an OHCI cleanup patch ... it removes a lot of erroneous whitespace
(space before tab, at end of line) as well as the obsolete inline changelog.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2006-12-20 10:14:26 -08:00
David Brownell
da66b719d1 [PATCH] ohci: don't play with IRQ regs
This is a more correct fix for the way the ohci hcd was referencing pt_regs
in the unlink paths.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-10-06 08:53:40 -07:00
David Howells
7d12e780e0 IRQ: Maintain regs pointer globally rather than passing to IRQ handlers
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.

The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around.  On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).

Where appropriate, an arch may override the generic storage facility and do
something different with the variable.  On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.

Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions.  Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller.  A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.

I've build this code with allyesconfig for x86_64 and i386.  I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.

This will affect all archs.  Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:

	struct pt_regs *old_regs = set_irq_regs(regs);

And put the old one back at the end:

	set_irq_regs(old_regs);

Don't pass regs through to generic_handle_irq() or __do_IRQ().

In timer_interrupt(), this sort of change will be necessary:

	-	update_process_times(user_mode(regs));
	-	profile_tick(CPU_PROFILING, regs);
	+	update_process_times(user_mode(get_irq_regs()));
	+	profile_tick(CPU_PROFILING);

I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().

Some notes on the interrupt handling in the drivers:

 (*) input_dev() is now gone entirely.  The regs pointer is no longer stored in
     the input_dev struct.

 (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking.  It does
     something different depending on whether it's been supplied with a regs
     pointer or not.

 (*) Various IRQ handler function pointers have been moved to type
     irq_handler_t.

Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 15:10:12 +01:00
David Brownell
0e4987639a [PATCH] USB: OHCI on Compaq Aramada 7400
This adds a quirk to the OHCI driver that lets it work with an old
Compaq implementation.  It also removes some needless strings from
the non-debug version of the driver.

Signed-off-by: Chris Clayton <chris_clayton@f1internet.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2005-04-18 17:39:30 -07:00
Linus Torvalds
1da177e4c3 Linux-2.6.12-rc2
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!
2005-04-16 15:20:36 -07:00