There are a few places where the RDMA CM code handles IPv6 by doing
struct sockaddr addr;
u8 pad[sizeof(struct sockaddr_in6) -
sizeof(struct sockaddr)];
This is fragile and ugly; handle this in a better way with just
struct sockaddr_storage addr;
[ Also roll in patch from Aleksey Senin <alekseys@voltaire.com> to
switch to struct sockaddr_storage and get rid of padding arrays in
struct rdma_addr. ]
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Consumers that want to re-use their QPs in new connections need to
know when the QP has exited the timewait state. Report the timewait
event through the rdma_cm.
Signed-off-by: Amir Vadai <amirv@mellanox.co.il>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add an RDMA_CM_EVENT_ADDR_CHANGE event can be used by rdma-cm
consumers that wish to have their RDMA sessions always use the same
links (eg <hca/port>) as the IP stack does. In the current code, this
does not happen when bonding is used and fail-over happened but the IB
link used by an already existing session is operating fine.
Use the netevent notification for sensing that a change has happened
in the IP stack, then scan the rdma-cm ID list to see if there is an
ID that is "misaligned" with respect to the IP stack, and deliver
RDMA_CM_EVENT_ADDR_CHANGE for this ID. The consumer can act on the
event or just ignore it.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The RDMA CM has some logic in place to make sure that callbacks on a
given CM ID are delivered to the consumer in a serialized manner.
Specifically it has code to protect against a device removal racing
with a running callback function.
This patch simplifies this logic by using a mutex per ID instead of a
wait queue and atomic variable. This means that cma_disable_remove()
now is more properly named to cma_disable_callback(), and
cma_enable_remove() can now be removed because it just would become a
trivial wrapper around mutex_unlock().
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Keep a pointer to the local (src) netdevice in struct rdma_dev_addr,
and copy it in as part of rdma_copy_addr(). Use rdma_translate_ip()
in cma_new_conn_id() to reduce some code duplication and also make
sure the src_dev member gets set.
In a high-availability configuration the netdevice pointer can be used
by the RDMA CM to align RDMA sessions to use the same links as the IP
stack does under fail-over and route change cases.
Signed-off-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The license text for several files references a third software license
that was inadvertently copied in. Update the license to what was
intended. This update was based on a request from HP.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The function rdma_create_id() always returns either a valid pointer or
a value made with ERR_PTR, so its result should be tested with IS_ERR,
not with a test for 0.
The problem was found using the following semantic match.
(http://www.emn.fr/x-info/coccinelle/)
//<smpl>
@a@
expression E, E1;
statement S,S1;
position p;
@@
E = rdma_create_id(...)
... when != E = E1
if@p (E) S else S1
@n@
position a.p;
expression E,E1;
statement S,S1;
@@
E = NULL
... when != E = E1
if@p (E) S else S1
@depends on !n@
expression E;
statement S,S1;
position a.p;
@@
* if@p (E)
S else S1
//</smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
There's an undesirable interaction with issuing MRA requests to
increase connection timeouts and the listen backlog.
When the rdma_cm receives a connection request, it queues an MRA with
the ib_cm. (The ib_cm will send an MRA if it receives a duplicate
REQ.) The rdma_cm will then create a new rdma_cm_id and give that to
the user, which in this case is the rdma_user_cm.
If the listen backlog maintained in the rdma_user_cm is full, it
destroys the rdma_cm_id, which in turns destroys the ib_cm_id. The
ib_cm_id generates a REJ because the state of the ib_cm_id has changed
to MRA sent, versus REQ received. When the backlog is full, we just
want to drop the REQ so that it is retried later.
Fix this by deferring queuing the MRA until after the user of the
rdma_cm has examined the connection request.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
in_dev_find() need a namespace to pass it to fib_get_table(), so add
an argument.
Signed-off-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
By default, the responder_resources parameter is set to that received
in a connection request. The passive side may override this value
when accepting the connection. Use the value provided by the passive
side when transitioning the QP to RTR state, rather than the value
given in the connect request. Without this change, the RTR transition
may fail if the passive side supports fewer responder_resources than
that in the request.
For code consistency and to protect against QP destruction, restructure
overriding initiator_depth to match how responder_resources is set.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
An IPoIB subnet on an IB fabric that spans multiple IB subnets can't
use link-local scope in multicast GIDs. The existing routines that
map IP/IPv6 multicast addresses into IB link-level addresses hard-code
the scope to link-local, and they also leave the partition key field
uninitialised. This patch adds a parameter (the link-level broadcast
address) to the mapping routines, allowing them to initialise both the
scope and the P_Key appropriately, and fixes up the call sites.
The next step will be to add a way to configure the scope for an IPoIB
interface.
Signed-off-by: Rolf Manderscheid <rvm@obsidianresearch.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Enable conn_id remove on the passive side after connection
establishment. This corrects an issue where the IB driver can't be
unloaded after running applications over RDS. The 'dev_remove' counter
does not reach 0 for established connections on the passive side.
This problem is limited to device removal, and only occurs on the
passive side if there are established connections.
Signed-off-by: Vladimir Sokolovsky <vlad@mellanox.co.il>
Reviewed-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Set the initiator depth and responder resources to the device max
values for new connect request events in the iWARP connection manager.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Increase command timeout for INIT_HCA to 10 seconds
IPoIB/cm: Use common CQ for CM send completions
IB/uverbs: Fix checking of userspace object ownership
IB/mlx4: Sanity check userspace send queue sizes
IPoIB: Rewrite "if (!likely(...))" as "if (unlikely(!(...)))"
IB/ehca: Enable large page MRs by default
IB/ehca: Change meaning of hca_cap_mr_pgsize
IB/ehca: Fix ehca_encode_hwpage_size() and alloc_fmr()
IB/ehca: Fix masking error in {,re}reg_phys_mr()
IB/ehca: Supply QP token for SRQ base QPs
IPoIB: Use round_jiffies() for ah_reap_task
RDMA/cma: Fix deadlock destroying listen requests
RDMA/cma: Add locking around QP accesses
IB/mthca: Avoid alignment traps when writing doorbells
mlx4_core: Kill mlx4_write64_raw()
There is a justifying patch for Stephen's patches. Stephen's patches
disallows using a port range of one single port and brakes the meaning
of the 'remaining' variable, in some places it has different meaning.
My patch gives back the sense of 'remaining' variable. It should mean
how many ports are remaining and nothing else. Also my patch allows
using a single port.
I sure we must be able to use mentioned port range, this does not
restricted by documentation and does not brake current behavior.
usefull links:
Patches posted by Stephen Hemminger
http://marc.info/?l=linux-netdev&m=119206106218187&w=2http://marc.info/?l=linux-netdev&m=119206109918235&w=2
Andrew Morton's comment
http://marc.info/?l=linux-kernel&m=119248225007737&w=2
1. Allows using a port range of one single port.
2. Gives back sense of 'remaining' variable.
Signed-off-by: Anton Arapov <aarapov@redhat.com>
Acked-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Deadlock condition reported by Kanoj Sarcar <kanoj@netxen.com>.
The deadlock occurs when a connection request arrives at the same
time that a wildcard listen is being destroyed.
A wildcard listen maintains per device listen requests for each
RDMA device in the system. The per device listens are automatically
added and removed when RDMA devices are inserted or removed from
the system.
When a wildcard listen is destroyed, rdma_destroy_id() acquires
the rdma_cm's device mutex ('lock') to protect against hot-plug
events adding or removing per device listens. It then tries to
destroy the per device listens by calling ib_destroy_cm_id() or
iw_destroy_cm_id(). It does this while holding the device mutex.
However, if the underlying iw/ib CM reports a connection request
while this is occurring, the rdma_cm callback function will try
to acquire the same device mutex. Since we're in a callback,
the ib_destroy_cm_id() or iw_destroy_cm_id() calls will block until
their callback thread returns, but the callback is blocked waiting for
the device mutex.
Fix this by re-working how per device listens are destroyed. Use
rdma_destroy_id(), which avoids the deadlock, in place of
cma_destroy_listen(). Additional synchronization is added to handle
device hot-plug events and ensure that the id is not destroyed twice.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If a user allocates a QP on an rdma_cm_id, the rdma_cm will automatically
transition the QP through its states (RTR, RTS, error, etc.) While the
QP state transitions are occurring, the QP itself must remain valid.
Provide locking around the QP pointer to prevent its destruction while
accessing the pointer.
This fixes an issue reported by Olaf Kirch from Oracle that resulted in
a system crash:
"An incoming connection arrives and we decide to tear down the nascent
connection. The remote ends decides to do the same. We start to shut
down the connection, and call rdma_destroy_qp on our cm_id. ... Now
apparently a 'connect reject' message comes in from the other host,
and cma_ib_handler() is called with an event of IB_CM_REJ_RECEIVED.
It calls cma_modify_qp_err, which for some odd reason tries to modify
the exact same QP we just destroyed."
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (87 commits)
mlx4_core: Fix section mismatches
IPoIB: Allow setting policy to ignore multicast groups
IB/mthca: Mark error paths as unlikely() in post_srq_recv functions
IB/ipath: Minor fix to ordering of freeing and zeroing of tid pages.
IB/ipath: Remove redundant link state checks
IB/ipath: Fix IB_EVENT_PORT_ERR event
IB/ipath: Better handling of unexpected GPIO interrupts
IB/ipath: Maintain active time on all chips
IB/ipath: Fix QHT7040 serial number check
IB/ipath: Indicate a couple of chip bugs to userspace
IB/ipath: iba6110 rev4 no longer needs recv header overrun workaround
IB/ipath: Use counters in ipath_poll and cleanup interrupts in ipath_close
IB/ipath: Remove duplicate copy of LMC
IB/ipath: Add ability to set the LMC via the sysfs debugging interface
IB/ipath: Optimize completion queue entry insertion and polling
IB/ipath: Implement IB_EVENT_QP_LAST_WQE_REACHED
IB/ipath: Generate flush CQE when QP is in error state
IB/ipath: Remove redundant code
IB/ipath: Future proof eeprom checksum code (contents reading)
IB/ipath: UC RDMA WRITE with IMMEDIATE doesn't send the immediate
...
Expansion of original idea from Denis V. Lunev <den@openvz.org>
Add robustness and locking to the local_port_range sysctl.
1. Enforce that low < high when setting.
2. Use seqlock to ensure atomic update.
The locking might seem like overkill, but there are
cases where sysadmin might want to change value in the
middle of a DoS attack.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Automatically queue MRA message to decrease the number of retries sent
by the remote side during connection establishment. This also has the
effect of increasing the overall connection timeout without using a
longer retry time in the case of dropped packets.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Provide support to specify a type of service for a communication
identifier. A new function call is used when dealing with IPv4
addresses. For IPv6 addresses, the ToS is specified through the
traffic class field in the sockaddr_in6 structure.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
[ The comments Eitan Zahavi and myself have made over the v1 post at
<http://lists.openfabrics.org/pipermail/general/2007-August/039247.html>
were fully addressed. ]
Reviewed-by: Or Gerlitz <ogerlitz@voltaire.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Local write permission makes no sense as part of the QP access flags,
since the access flags only control what the remote end of the
connection is allowed to do. Remove the code in the RDMA CM that
initializes qp_access_flags with IB_ACCESS_LOCAL_WRITE.
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Acked-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The IB CM should include the HCA ACK delay when calculating the local
ACK timeout value to use for RC QPs. If the HCA ACK delay is large
enough relative to the packet life time, then if it is not taken into
account, the calculated timeout value ends up being too small, which
can result in "retry exceeded" errors.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
next_port should be between sysctl_local_port_range[0] and [1].
However, it is initially set to a random value with get_random_bytes().
If the value is negative when treated as a signed integer, next_port
can end up outside the expected range because of the result of the %
operator being negative.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Several checks in the rdma_cm check against the state of the
cm_id, but only to validate that the cm_id is bound to an underlying
transport specific CM and an RDMA device. Make the check explicit
in what we're trying to check for, since we're not synchronizing
against the cm_id state.
This will allow a user to disconnect a cm_id or reject a connection
after receiving a device removal event.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The cma_iw_handler needs to validate the state of the rdma_cm_id before
processing a new connection request to ensure that a device removal is
not already being processed for the same rdma_cm_id. Without the state
check, the user can receive simultaneous callbacks for the same cm_id, or
a callback after they've destroyed the cm_id.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Add a new routine and rename another to encapsulate common code for
synchronizing with device removal.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The struct rdma_bind_list fields for hlist are not being initialized,
resulting in a corrupted list. Fix this by using kzalloc() to make
sure all pointers are NULL.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The rdma_cm requires that path records be reversible. Set the
reversible bit when issuing an path record query.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Extend rdma_cm to support multicast communication. Multicast support
is added to the existing RDMA_PS_UDP port space, as well as a new
RDMA_PS_IPOIB port space. The latter port space allows joining the
multicast groups used by IPoIB, which enables offloading IPoIB traffic
to a separate QP. The port space determines the signature used in the
MGID when joining the group. The newly added RDMA_PS_IPOIB also
allows for unicast operations, similar to RDMA_PS_UDP.
Supporting the RDMA_PS_IPOIB requires changing how UD QPs are initialized,
since we can no longer assume that the qkey is constant. This requires
saving the Q_Key to use when attaching to a device, so that it is
available when creating the QP. The Q_Key information is exported to
the user through the existing rdma_init_qp_attr() interface.
Multicast support is also exported to userspace through the rdma_ucm.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Randomize the starting port number and avoid re-using port values
immediately after they are closed. Instead keep track of the last
port value used and increment it every time a new port number is
assigned, to better replicate other port spaces.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The iWARP CM should report timeouts as event RDMA_CM_EVENT_UNREACHABLE,
not event RDMA_CM_EVENT_REJECTED.
Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Allow the use of UD QPs through the rdma_cm, in order to provide
address translation services for resolving IB addresses for datagram
messages using SIDR.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
During connection establishment, the passive side of a connection can
receive messages from the active side before the connection event has
been delivered to the user. Allow the passive side to send messages
in response to received data before the event is delivered. To handle
the case where the connection messages are lost, a new rdma_notify()
function is added that users may invoke to force a connection into the
established state.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Connection information was never given to the recipient of a
connection request or reply message. Only the event was delivered.
Report the connection data with the event to allows user to
reject the connection based on the requested parameters, or adjust
their resources to match the request.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The qp_type parameter into the rdma_cm is unneeded, and can be
misleading. The QP type should be determined from the port space.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Conflicts:
drivers/infiniband/core/iwcm.c
drivers/net/chelsio/cxgb2.c
drivers/net/wireless/bcm43xx/bcm43xx_main.c
drivers/net/wireless/prism54/islpci_eth.c
drivers/usb/core/hub.h
drivers/usb/input/hid-core.c
net/core/netpoll.c
Fix up merge failures with Linus's head and fix new compilation failures.
Signed-Off-By: David Howells <dhowells@redhat.com>
The qp_access_flags are for remote access permissions only, so
IB_ACCESS_LOCAL_WRITE is an invalid value. Remove it from the values
set by cm_init_qp_init_attr() and cma_init_ib_qp().
Signed-off-by: Dotan Barak <dotanb@mellanox.co.il>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Rewrite cma_req_handler error handling case to encapsulate
common code.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove redundant check of node_guid in cma_add_one().
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Optimize to test for an empty list first. This ends up simplifying
the code too.
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Acked-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Require registration with ib_addr module to prevent caller from
unloading while a callback is in progress.
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Reorganize code relating to cma_get_net_info() and rdam_create_id() to
optimize error case handling (no need to alloc memory/etc. as part of
rdma_create_id() if input parameters are wrong).
Signed-off-by: Krishna Kumar <krkumar2@in.ibm.com>
Signed-off-by: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
