Set the default value of position_fix -1, and allow user passing
position_fix=0 explicitly to set the "auto" position-fix mode.
Otherwise the auto mode may be switched to others like COMBO of
VIACOMBO when the controller prefers it, thus user can't set the auto
mode any longer.
Also updated the documentation appropriately, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Due to the definitions of CS420X_IMAC27_122 and CS420X_APPLE as
aliases, the rest enums are set to duplicated values unexpectedly.
Move the alias definitions at the end so that the enum values are
defined in the proper order.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
MacBook Pro 10,1 needs a few adjustments to make it working:
- more COEF verbs
- some pin config overrides to disable the unused pin (0x0d, 0x12),
and fix the internal mic (0x0e)
In addition, it uses GPIO 1 and 3 like other MacBooks.
The internal digital mic on the machine is still problematic: it seems
that only the right channel is used and the left is always static.
This looks like a hardware design, so we need to cope in the software
side somehow...
The primary information and test were brought from Daniel J Blueman.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_pick_fixup() didn't check the case where the device mask bits
are set, typically used for SND_PCI_QUIRK_VENDOR() entries. Fix this.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Originally the bogus period at BDL head was introduced as a workaround
for the mismatching position update at the period boundary, typically
seen on dmix. However, for applications like PulseAudio that don't
require period wake ups, this workaround is just superfluous. Thus
better to disable it when no_period_wakeup is given in hw_params.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit c20c5a841c changed some chipsets to
default to POS_FIX_COMBO so they now use POS_FIX_LPIB instead of
POS_FIX_POSBUF. Since then I've been getting artifacts on playback, including
repeated sounds on my Asus laptop.
My hardware is Cougar Point which the commit log of
c20c5a841c mentions as tested so POS_FIX_COMBO
probably works in general but apparently it doesn't on Asus K53E therefore the
need for the quirk.
Signed-off-by: Catalin Iacob <iacobcatalin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
snd_hda_codec_reset() calls restore_pincfgs() where the codec is
powered up again, which eventually tries to resume and initialize via
the callbacks of the codec. However, it's the place just after codec
free callback, thus no codec callbacks should be called after that.
On a codec like CS4206, it results in Oops due to the access in init
callback.
This patch fixes the issue by clearing the codec callbacks properly
after freeing codec.
Reported-by: Daniel J Blueman <daniel@quora.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The purpose of this flag is unclear. If the problem is that some machines
have broken misc/NO_PRESENCE bits, they should be fixed by pin fixups.
In addition, this causes jack detection functionality to be flawed on
the M31EI, where there are two jacks without jack detection (which is
properly marked as NO_PRESENCE), but due to ignore_misc_bit, these
jacks are instead being reported as being present but always unplugged.
BugLink: https://bugs.launchpad.net/bugs/939161
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... instead of the standard fixed channel maps.
The generic HDMI is based on the audio infoframe, and its configuration
can be selected via CA bits. Thus we need a translation between the
CA index and the verbose channel map list.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Although HD-audio allows pair-wise channel configurations, only the
fixed channel positions are used in this version. In future, this can
be changed and allow user to modify the channel positions.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Recently the check for non-PCM stream state was added to the generic
HDMI driver code. But this check should be done rather to each pin
instead of each converter. Otherwise when a different converter is
assigned at the next open, the audio infoframe can be inconsistent
with the setup using the previous converter.
For fixing this issue, this patch moves the state of the current
non-PCM status from per_cvt to per_pin. (In addition an unused
argument cvt_nid is stripped from hdmi_setup_channel_mapping())
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For multiple speaker outs, the names were previously
"Speaker,0", "Speaker,1", "Center"/"LFE", "Speaker,3". This is
inconsistent, confusing, and is not picked up correctly by PulseAudio.
Instead use "Front", "Surround", "Center"/"LFE", "Side" which
is more standard.
BugLink: https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1046734
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the commit [2faa3bf: ALSA: hda - Rewrite the mute-LED hook with
vmaster hook in patch_sigmatel.c], the former Master volume control
was converted to PCM. This was supposed to be covered by the vmaster
control. But due to the lack of "PCM" slave definition, this didn't
happen properly. The patch fixes the missing entry.
Reported-by: Andrew Shadura <bugzilla@tut.by>
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For HBR stream test, use straight channel mapping way.
when switched back to "speaker-test -c8", even the audio
infoframe is up-to-date, there should be correct channel mapping setup.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
HDMI channel remapping apparently effects HBR packets on Intel's chips.
For compressed non-PCM audio, use "straight-through" channel mapping.
For uncompressed multi-channel pcm audio, use normal channel mapping.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The array channel_allocations[] is an ordered list, add function to get
correct order by ca_index.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The call of pm_notify callback in snd_hda_codec_free() should be with
the check of the current state whether pm_notify(false) is called or
not, instead of codec->power_on check.
For improving the code readability and fixing this inconsistency,
codec->d3_stop_clk_ok is renamed to codec->pm_down_notified, and this
flag is set only when runtime PM down is called. The new name reflects
to a more direct purpose of the flag.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CONFIG_SND_HDA_POWER_SAVE is no longer an experimental feature and its
behavior can be well controlled via the default value and module
parameter. Let's just replace it with the standard CONFIG_PM.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When a codec provides its own set_power_state op, the D3-clock-stop
isn't checked correctly. And the recent changes for repeating the
state-setting operation isn't applied to such a codec, too.
This patch fixes these issues by moving the call of codec's own op to
the place where the generic power-set operation is done, and move the
power-state synchronization code out of
snd_hda_set_power_state_to_all() so that it can be called always at
the end of power-up/down sequence, and updates the D3 clock-stop flag
properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the HD-audio is removed, it leaves the refcounts when codecs are
powered up (usually yes) in the destructor. For fixing the unbalance,
and cleaning up the code mess, this patch changes the following:
- change pm_notify callback to take the explicit power on/off state,
- check of D3 stop-clock and keep_link_on flags is moved to the caller
side,
- call pm_notify callback in snd_hda_codec_new() and snd_hda_codec_free()
so that the refcounts are proprely updated.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These codecs seem reporting EPSS but require longer delay for the
proper D3 transition. For example, D3_STOP_CLOCK_OK bit won't be set
correctly even after D3.
In this patch, codec->epss flag is overridden for avoid the
misbehavior.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
EPSS parameter should be static, so we can read it once and remember.
This also allows more easily to override the wrong EPSS capability
reported from a codec by changing the flag in the codec
initialization step.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use unsigned int to make clear that the codes required only for
modules will be reduced by the compiler optimization.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The patch to support runtime PM introduced a bug:
Module parameter 'power_save_controller', and the codec flag 'd3_stop_clk'
'd3_stop_clk_ok' are defined only when HDA power save is enabled in config. But
there are references to them without checking macro CONFIG_SND_HDA_POWER_SAVE.
This patch is to fix the bug.
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Runtime PM can bring more power saving:
- When the controller is suspended, its parent device will also have a chance
to suspend.
- PCI subsystem can choose the lowest power state the controller can signal
wake up from. This state can be D3cold on platforms with ACPI PM support.
And runtime PM can provide a gerneral sysfs interface for a system policy
manager.
Runtime PM support is based on current HDA power saving implementation. The user
can enable runtime PM on platfroms that provide acceptable latency on transition
from D3 to D0.
Details:
- When both power saving and runtime PM are enabled:
-- If a codec supports 'stop-clock' in D3, it will request suspending the
controller after it enters D3 and request resuming the controller before
back to D0. Thus the controller will be suspended only when all codecs are
suspended and support stop-clock in D3.
-- User IO operations and HW wakeup signal can resume the controller back to
D0.
- If runtime PM is disabled, power saving just works as before.
- If power saving is disabled, the controller won't be suspended because the
power usage counter can never be 0.
More about 'stop-clock' feature:
If a codec can support targeted pass-through operations in D3 state when there
is no BCLK present on the link, it will set CLKSTOP flag in the supported power
states and report PS-ClkStopOk when entering D3 state. Please refer to HDA spec
section 7.3.3.10 Power state and 7.3.4.12 Supported Power State.
[Fixed CONFIG_PM_RUNTIME dependency in hda_intel.c by tiwai]
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of calling the jack sync in the init callback of each codec,
call it generically at initialization and resume. By calling it at
the last of resume sequence, a possible race between the jack sync and
the unsol event enablement in the current code will be closed, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This fixes an issue with a machine where there were no speakers,
but GPIO0 had to be data=1 for the headphone to be functioning.
I'm not sure if we need a more advanced patch to solve all possible cases,
but if so, this patch would still provide a minor optimisation.
BugLink: https://bugs.launchpad.net/bugs/1040077
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When the codec turn-on operation is canceled by the immediate
power-on, the driver left the power_transition flag as is.
This caused the persistent avoidance of power-save behavior.
Cc: <stable@vger.kernel.org> [v3.5+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
... by calling the newly introduced snd_hda_power_sync().
I had to reimplement a wheel for adding the trigger at changing the
parameter -- the parameter set ops is overwritten to pass the integer
parameter, then trigger the power-state sync.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a new helper function snd_hda_power_sync() to trigger the
power-saving manually. It's an inline function call to
snd_hda_power_save() helper function.
Together with this addition, snd_hda_power_up*() and
snd_hda_power_down() functions are inlined to a call of the same
snd_hda_power_save() helper function.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's possible that these amps are settable somehow, e g through
secret codec verbs, but for now, don't create the controls (as
they won't be working anyway, and cause errors in amixer).
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1038651
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of blindly initializing a volume knob widget, first check
that there actually is a volume knob widget.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Added a simple support of automute for the front HP jack to AD1882
stack model. Such an addition is basically an exception -- we really
want to avoid the static quirk codes, but AD1882 parser isn't still
ready for moving to the BIOS auto-parser yet. So, as a quick fix, I
merged it for now.
In near future, we really need the big clean up of patch_analog.c to
move on to the auto-parser...
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace with a proper ifdef check of CONFIG_PM_SLEEP in hda_intel.c.
But other places in HD-audio driver are still marked with CONFIG_PM,
since these can be called for power-saving even without
CONFIG_PM_SLEEP.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some Conexant devices (e g CX20590) have no mute capability on
their Beep widgets.
This patch makes sure we don't try setting mutes on those widgets.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As spec said, 1 indicates no copyright is asserted.
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The return value of snd_hda_param_read() is -1 for an error, otherwise
it's the supported power states of a codec.
The supported power states is a 32-bit value. Bit 31 will be set to 1
if the codec supports EPSS, thus making "sup" negative. And the bit
28:5 is reserved as "0".
So a negative value other than -1 shall be further checked.
Please refer to High-Definition spec 7.3.4.12 "Supported Power
States", thanks!
Signed-off-by: Mengdong Lin <mengdong.lin@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When "Beep Playback Switch" had a different value on left and right
channels (such as muting left but not right, or vice versa), this
could result in the right channel being ignored.
This patch enables beep to be sounding from right channel only, and
also give correct result back to userspace (e g amixer).
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch adds the Intel HD Audio Device IDs for the Intel Lynx Point-LP PCH
Signed-off-by: James Ralston <james.d.ralston@intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
For processing the firmware handling properly for built-in kernels,
implement an asynchronous firmware loading with
request_firmware_nowait(). This means that the codec probing is
deferred when the patch option is specified.
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This is a preliminary work for the deferred probing for
request_firmware() errors at init.
This patch moves the call of request_firmware() to hda_intel.c, and
call it in the earlier stage of probing rather than
azx_probe_continue().
Tested-by: Thierry Reding <thierry.reding@avionic-design.de>
Reviewed-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To turn off pin control for the pin was tested, and helped against
this issue.
BugLink: https://bugs.launchpad.net/bugs/1034779
Tested-by: Chih-Hsyuan Ho <chih.ho@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
CA0132 driver had some codes to handle the S/PDIF I/O, but the actual
setups of pins and converters were missing. Now the pins are added.
Also, fixed a few points triggering invalid codec verbs and mixer
elements since the digital I/O audio widgets on CA0132 have no amp.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now with the workaround using codec->pcm_format_first flag, we can
clean up the home-baked codes in patch_ca0132.c.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Introduced a new flag to set up the PCM stream format at first before
the stream_id and channel tag. Some codecs (e.g. CA0132) seem
preferring this over stream_id -> format order.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The same ID is twice in the quirk table, so the second one is not used.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When CONFIG_SND_VERBOSE_PRINTK=y is set, the debug print in
hda_auto_parser.c looks really ugly like:
ALSA sound/pci/hda/hda_auto_parser.c:331 mono: mono_out=0x0
ALSA sound/pci/hda/hda_auto_parser.c:334 dig-out=0x12/0x0
ALSA sound/pci/hda/hda_auto_parser.c:335 inputs:
ALSA sound/pci/hda/hda_auto_parser.c:339 Mic=0x11ALSA sound/pci/hda/hda_auto_parser.c:339 Line=0x10
ALSA sound/pci/hda/hda_auto_parser.c:341
ALSA sound/pci/hda/hda_auto_parser.c:343 dig-in=0x13
Better to put one item at each line.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the auto model is the default, these quirks are redundant
and can be removed.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This computer is confirmed working with model=auto on kernel 3.2.
Also, parsing fails with hda-emu with the current model.
Cc: stable@kernel.org (3.2+)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
As with the ThinkPad Models X230 Tablet and T530 the X230 needs a qurik to
correctly set up the pins for the dock port.
Signed-off-by: Felix Kaechele <felix@fetzig.org>
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit c4bfe94a causes a regression on some codecs at probing.
Since this was just a workaround to shut up a kernel warning, it'd be
better to revert and fix properly. So we ended up with re-adding the
cleanup callback.
Tested-and-reported-by: Matt Horan <matt@matthoran.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add a model/fixup string "lenovo-dock", for Thinkpad T430s, to allow
sound in docking station.
Tested on Lenovo T430s with ThinkPad Mini Dock Plus Series 3
Cc: stable@kernel.org
Signed-off-by: Philipp A. Mohrenweiser <phiamo@googlemail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Lenovo Thinkpad T530 with ALC269VC codec has a dock port but BIOS
doesn't set up the pins properly. Enable the pins as well as on
Thinkpad X230 Tablet.
Reported-and-tested-by: Mario <anyc@hadiko.de>
Cc: <stable@vger.kernel.org> [v3.2+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The IDT codecs initializes the GPIO setup for mute LEDs via
snd_hda_sync_vmaster_hook(). This works in most cases except for the
very first call, which is called before PCM and control creations.
Thus before Master switch is set manually via alsactl, the mute LED
may show the wrong state, depending on the polarity.
Now it's fixed by calling the LED-status update function manually when
no vmaster is set yet.
Cc: <stable@vger.kernel.org> [v3.4+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The commit a3e199732b made the LED working again on HP Mini 210 but
with a wrong polarity. This patch fixes the polarity for this
machine, and also introduce a new model string "hp-inv-led".
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=772923
Cc: <stable@vger.kernel.org> [v3.3+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On recent kernels, Realtek codec parser tries to optimize the routing
aggressively and take the headphone output as primary at first. This
caused a regression on VAIO Z with ALC889, the silent output from the
speaker.
The problem seems that the speaker pin must be connected to the first
DAC (0x02) on this machine by some reason although the codec itself
advertises the flexible routing with any DACs.
This patch adds a fix-up for choosing the speaker pin as the primary
so that the right DAC is assigned on this device.
Reported-and-tested-by: Adam Williamson <awilliam@redhat.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix to converter detaching timing in patch_hdmi.c
leads to a kernel WARNING due to a sanity check when the debug
option is set. Add a workaround by setting a dummy hinfo->nid.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The generic HDMI code detaches the converter from the stream when
unused, but it must be done rather in the close callback instead of
the cleanup callback.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
BIOS on HP Mini 210 doesn't provide the proper "HP_Mute_LED" DMI
string, thus the driver doesn't initialize the GPIO, too. In the
earlier kernel, the driver falls back to GPIO1, but since 3.3 we've
stopped this due to other wrongly advertised machines.
For fixing this particular case, add a new model type to specify the
default polarity explicitly so that the fallback to GPIO1 is handled.
Bugzilla: https://bugzilla.novell.com/show_bug.cgi?id=772923
Cc: <stable@vger.kernel.org> [v3.3+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We've got a bug report about the silent output from the headphone on a
mobo with VT2021, and spotted out that this was because of the wrong
D3 state on the DAC for the headphone output. The bug is triggered by
the incomplete check for this DAC in set_widgets_power_state_vt1718S().
It checks only the connectivity of the primary output (0x27) but
doesn't consider the path from the headphone pin (0x28).
Now this patch fixes the problem by checking both pins for DAC 0x0b.
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Also add a model/fixup string "lenovo-dock", so that other Thinkpad
users will be able to test this fixup easily, to see if it enables
dock I/O for them as well.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1026953
Tested-by: John McCarron <john.mccarron@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Turn on the pin widget's PIN_OUT bit from playback prepare. The pin is
enabled in open, but is disabled in hdmi_init_pin which is called during
system resume. This causes a system suspend/resume during playback to
mute HDMI/DP. Enabling the pin in prepare instead of open allows calling
snd_pcm_prepare after a system resume to restore audio.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This merges the changes for converting to new PM ops for platform
and some other drivers.
Also move some header files to local places from the public
include/sound.
A recent commit made patch_alc268 call snd_hda_pick_fixup with
NULL quirk pointer. Make sure we do not reference that NULL pointer.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This codec has a separate dmic path (separate dmic only ADC),
and thus it looks mostly like ALC275.
Cc: stable@kernel.org
BugLink: https://bugs.launchpad.net/bugs/1025377
Tested-by: Ray Chen <ray.chen@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since some jack controls may be renamed as phantom jacks, the existing
check for index conflicts doesn't work because it simply compares the
name with the last used name, assuming that the controls with the same
name continue. Thus, it would result in the duplicated controls when
two or more phantom jacks with the very same type exist, and the
driver gives up with an error.
This patch fixes the problem by checking the index number conflicts
more intensively (but dumbly).
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Vendor ID 0x10de0051 is used by a yet-to-be-named GPU chip.
Signed-off-by: Aaron Plattner <aplattner@nvidia.com>
Acked-by: Andy Ritger <aritger@nvidia.com>
Reviewed-by: Daniel Dadap <ddadap@nvidia.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
this patch add proper id for Haswell HDA Controller.
[Added AZX_DCAPS_POSFIX_COMBO flag by tiwai]
Signed-off-by: Wang Xingchao <xingchao.wang@intel.com>
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With the model parsers out of the way, we have no custom unsol
events to worry about, we can therefore simplify the code.
In addition, this fixes a bug on the ASUS TC710, which has only
a headphone jack and a mic jack, but no internal mic or speakers.
Therefore the unsol_event pointer was not set, and as a result,
the jack kcontrols were not correctly updated.
BugLink: https://bugs.launchpad.net/bugs/1021192
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Call cancel_work_sync() when turning off the beep switch so that the
mute call is executed in a proper order.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's no longer necessary since beep_mode=2 option was dropped.
It can be checked simply via codec->beep != NULL.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Move snd_hda_mixer_amp_switch_put_beep() to hda_beep.c as a clean up
to remove one more ifdef.
Also add the corresponding get callback to return consistently the
digital beep state independently from the mixer amp value.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The beep_mode=2 option was introduced to make the beep mixer
controlling the beep input allocation/deallocation dynamically, so
that a user can switch between HD-audio codec digital beep and the
system beep only via mixer API. This was necessary because the
keyboard driver took only the first input beep instance at that time.
However, the recent keyboard driver already processes the multiple
input instances, thus there is no point to keep this mode.
Let's remove it.
Acked-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Straightforward conversion to the new pm_ops from the legacy
suspend/resume ops.
Since we change vx222, vx_core and vxpocket have to be converted,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Windows use hidden register to control EAPD.
Linux use verb to control EAPD.
If windows reboot to Linux, it must change the EAPD control to verb
control.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This 3-pin jack was labeled "Headphone Jack", but it could also be
used as a mic jack just by switching "Input Source". Therefore we need
to call the jack something else, to make sure PulseAudio can use the
speaker together with the external mic. (PulseAudio might mute the
speaker if it detects a headphone being plugged in.)
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some ASUS device has a single 3-pin jack that can either be a mic or
a headphone, but the pin does not have VREF capabilities. We've been
told by Realtek to instead enable VREF on pin 0x18 in that case.
BugLink: https://bugs.launchpad.net/bugs/1018262
Tested-by: Chih-Hsyuan Ho <chih.ho@canonical.com>
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The recent fix for power-map controls (commit b0791dda81) caused
regressions on some other HP laptops. They have fixed pins but these
pins are exposed as jack-detectable. Thus the driver tries to control
the power-map dynamically per jack detection where it never gets on.
This patch adds the check of connection and it assumes the no jack
detection is available for fixed pins no matter what pin capability
says.
BugLink: http://bugs.launchpad.net/bugs/1013183
Reported-by: Luis Henriques <luis.henriques@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
