* Always free tx buffers before reset, since we also empty hw queues.
If we don't and a queue gets stuck, we'll never decrease txq_len and sw
will keep thinking the queue is still stuck even after reset.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* By skipping tx power table calibration we also skip setting
tx power table on hw. Make sure we always write tx power table
on hw since it gets cleared on reset.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This prepares the only place which uses the EWMA library so far for the
performance improved implementation coming up, which requires factor and
weight to be a power of two.
Signed-off-by: Bruno Randolf <br1@einfach.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On WiSoc we cannot access mac register before it is resetted.
It will crash hardware otherwise.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AHB specific functions are now in ahb.c file. AHB bus is
compiled in when CONFIG_ATHEROS_AR231X is set in kernel.
All other platforms will use PCI bus.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add bus dependent revision read function which is used to
determine chipset's MAC before hardware is initialized.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To be able to support other busses than PCI check if pci device
structure is initialized.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Split pci initialization into hardware specific
functions and softc structure initialization.
Make function naming similar to ones ath9k.
Introduce ath_bus_opts in ath5k for later
AHB bus integration.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Wojciech Dubowik <Wojciech.Dubowik@neratec.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: linux-wireless@vger.kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Invert test and return early.
Move variable declarations to local scope.
Don't initialize variables to 0 unnecessarily.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes debugfs problems when a phy is renamed,
and is able to remove a bit of code that is no longer
needed.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Specs were updated plus we become wl compatible.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reverts commit 916448e77f.
"As far as I can tell, either of these patches breaks multiple VIF
scenarios. I'm not sure exactly why, but I had to revert this to
get any of my interfaces to associate."
-- Ben Greear <greearb@candelatech.com>
http://marc.info/?l=linux-wireless&m=129123368719339&w=2
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A few LNA control related flags were also specified as a bitfields, however
for some strange reason they were written in big-endian order this time.
Fix this by using flags instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Parsing data using bitfields is messy, because it makes endian handling
much harder. AR9002 and earlier got it right, AR9003 got it wrong.
This might lead to either using too high or too low tx power values,
depending on frequency and eeprom settings.
Fix it by getting rid of the CTL related bitfields entirely and use
masks instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The register which gives input gpio state is 0x404c for ar9003,
currently 0x4048 is wrongly used. This will disable RF and make
it unusable on some of AR9003.
Cc:stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Change the module parameter name to bt_ch_inhibition from
bt_ch_announce to better describe the functionality
In order to allow Bluetooth to activate a smart AFH mechanism
and to maximize its available bandwidth the WiFi will request
BT Core to inhibit its activity in channels that interfere
with WiFi activity (and vice versa) if bt_ch_inhibition is enabled
Set module parameter "bt_ch_inhibition=0" will disable the channel
inhibition function
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
If driver is on the way down, there is no need to send
RXON to uCode, check the condition before continuous the process.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
PCI L1 Active needs to be disabled while loading the uCode so that the bus
doesn't go to sleep. The enablement of L1 Active should be done after
the uCode has sent the ALIVE response. The enablement of L1 Active was
missing.
Enabling L1 Active allows to save power if the BIOS / bus driver allows
it.
I measured the power consumption while not associated and
idle/associated:
L1 Active disabled: 39 mA = 130mW
L1 Active enabled: 6 mA = 20 mW
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
During reprogram stations, do not send link quality command.
uCode will crash if receive link quality command for invalid station
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Commit dbbf1755b0 "iwlwifi: use
antenna information in EEPROM" caused 4965 device breakage with
"Microcode SW error detected. Restarting 0x82000000." message.
This patch reverts 4965 part of that commit.
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All rt2x00 drivers except rt2800pci call ieee80211_tx_status() from
a workqueue, which causes "NOHZ: local_softirq_pending 08" messages.
To fix it, add ieee80211_tx_status_ni() similar to ieee80211_rx_ni()
which can be called from process context, and call it from
rt2x00lib_txdone(). For the rt2800pci special case a driver
flag is introduced.
Signed-off-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* A diff between rfbuffer settings of turbo and non-turbo
modes indicates there is a bit on bank 2 related to turbo operation
(it's set on turbo modes). This bit is present on all radios except
RF5413 that seems to have a completely different bank 2. Also
since 2317 has the same rf-registers locations with 2425 and
since the bit exists on 2317 I assume it also exists on 2425/2417).
So in case we use turbo mode (40MHz) enable it on bank modification.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up what's left of turbo mode, since we handle all
register modifications (rfbuffer comes next) on code there
is no need to have duplicated arrays.
* Rename change_channel to skip_pcu on initvals.c as we did
on reset.c
Signed-off-by: Nick Kossifidis <micklfemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Clean up CHANNEL_T(URBO), use AR5K_BWMODE_40MHZ instead
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Use correct clock value when setting OFDM timings on
non-default bwmodes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Don't return -EINVAL when trying to set tx power
on RF5110 because AR5210 reset will fail. We need to
add support for RF5110 and AR5210 eeprom in the future
but for now just skip it.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Tweak phy activation -> rx delay for different bwmodes
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Since we set antenna flags on phy init and ack bitrate
mode on pcu init, there is no need to save/restore sta_id
flags on ath5k_hw_reset. Also we don't need to re-set our
mac address because it's not affected by resets.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add synth-only channel change for AR2413/5413. When we call
ath5k_reset with a channel ath5k_hw_reset will first try to
set channel on PHY while PHY is running instead of doing a normal
full reset. To do this phy_init has to change to implement this
functionality.
* Clean up change_channel flag, what it really did was skip PCU
registers when setting initvals. This is done because on reset
PCU registers are not affected (except the registers we set
in pcu init and -due to hw problems- TSF). Use a new skip_pcu
flag that's not misleading instead. In the future we might use
that to also skip PCU reset and save us the TSF etc problems
(needs testing because standard practice is to reset everything).
* Use fast channel change only when setting channel, and set skip_pcu
to false only on init. When we reset the card due to DMA or PHY
problems skip pcu but never do a fast channel change.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Only set power table if we are changing channel/mode
there is no need to recalculate and reset the power table
all the time.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Set correct PLL settings for each bwmode
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Add spur mitigation filter support for half/quarter and turbo.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Tweak power detector delays on AR5111/AR5112 when
using half/quarter modes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* Make sure we always set IFS timings even if no
coverage class is set. If we don't we'll miss the
needed changes for different bwmodes.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
