When a userspace SME is active, we're currently not
keeping track of the BSS properly for reporting the
current link and for internal use. Additionally, it
looks like there is a possible BSS leak in that the
BSS never gets removed from auth_bsses[]. To fix it,
pass the BSS struct to __cfg80211_connect_result in
this case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When downing interfaces, it's a good idea to tell the driver to
stop sending beacons; that way the driver doesn't need special
code in ops->remove_interface() when it should already handle the
case in bss_info_changed().
This fixes a potential crash with at least ath5k since the vif
pointer will be nullified while beacon interrupts are still active.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel Roskin reported a problem that seems to be due to
software retry of already transmitted frames. It turns
out that we've never done that correctly, but due to
some recent changes it now crashes in the TX code. I've
added a comment in the patch that explains the problem
better and also points to possible solutions -- which
I can't implement right now.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A regression was added through patch a4ed90d6:
"cfg80211: respect API on orig_flags on channel for beacon hint"
We did indeed respect _orig flags but the intention was not clearly
stated in the commit log. This patch fixes firmware issues picked
up by iwlwifi when we lift passive scan of beaconing restrictions
on channels its EEPROM has been configured to always enable.
By doing so though we also disallowed beacon hints on devices
registering their wiphy with custom world regulatory domains
enabled, this happens to be currently ath5k, ath9k and ar9170.
The passive scan and beacon restrictions on those devices would
never be lifted even if we did find a beacon and the hardware did
support such enhancements when world roaming.
Since Johannes indicates iwlwifi firmware cannot be changed to
allow beacon hinting we set up a flag now to specifically allow
drivers to disable beacon hints for devices which cannot use them.
We enable the flag on iwlwifi to disable beacon hints and by default
enable it for all other drivers. It should be noted beacon hints lift
passive scan flags and beacon restrictions when we receive a beacon from
an AP on any 5 GHz non-DFS channels, and channels 12-14 on the 2.4 GHz
band. We don't bother with channels 1-11 as those channels are allowed
world wide.
This should fix world roaming for ath5k, ath9k and ar9170, thereby
improving scan time when we receive the first beacon from any AP,
and also enabling beaconing operation (AP/IBSS/Mesh) on cards which
would otherwise not be allowed to do so. Drivers not using custom
regulatory stuff (wiphy_apply_custom_regulatory()) were not affected
by this as the orig_flags for the channels would have been cleared
upon wiphy registration.
I tested this with a world roaming ath5k card.
Cc: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
These pointers can be NULL, the is_mesh() case isn't
ever hit in the current kernel, but cmp_ies() can be
hit under certain conditions.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Cc: stable@kernel.org [2.6.29, 2.6.30]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfcomm tty may be used before rfcomm_tty_driver initilized,
The problem is that now socket layer init before tty layer, if userspace
program do socket callback right here then oops will happen.
reporting in:
http://marc.info/?l=linux-bluetooth&m=124404919324542&w=2
make 3 changes:
1. remove #ifdef in rfcomm/core.c,
make it blank function when rfcomm tty not selected in rfcomm.h
2. tune the rfcomm_init error patch to ensure
tty driver initilized before rfcomm socket usage.
3. remove __exit for rfcomm_cleanup_sockets
because above change need call it in a __init function.
Reported-by: Oliver Hartkopp <oliver@hartkopp.net>
Tested-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Current neigh_periodic_timer() function is fired by timer IRQ, and
scans one hash bucket each round (very litle work in fact)
As we are supposed to scan whole hash table in 15 seconds, this means
neigh_periodic_timer() can be fired very often. (depending on the number
of concurrent hash entries we stored in this table)
Converting this to a workqueue permits scanning whole table, minimizing
icache pollution, and firing this work every 15 seconds, independantly
of hash table size.
This 15 seconds delay is not a hard number, as work is a deferrable one.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since pr_err and friends are used instead of printk there is no point
in keeping IP_VS_ERR and friends. Furthermore make use of '__func__'
instead of hard coded function names.
Signed-off-by: Hannes Eder <heder@google.com>
Acked-by: Simon Horman <horms@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This renames away a variable clash:
* ipv6_table[] is declared as a static global table;
* ipv6_sysctl_net_init() uses ipv6_table to refer/destroy dynamic memory;
* ipv6_sysctl_net_exit() also uses ipv6_table for the same purpose;
* both the two last functions call kfree() on ipv6_table.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a path when an assetion in dev_unicast_sync() appears.
igmp6_group_added -> dev_mc_add -> __dev_set_rx_mode ->
-> vlan_dev_set_rx_mode -> dev_unicast_sync
Therefore we cannot protect this list with rtnl. This patch restores the
original protecting this list with spinlock.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Tested-by: Meelis Roos <mroos@linux.ee>
Signed-off-by: David S. Miller <davem@davemloft.net>
memcpy() should take into account size of pointers,
not only number of pointers to copy.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Choose saner defaults for xfrm[4|6] gc_thresh values on init
Currently, the xfrm[4|6] code has hard-coded initial gc_thresh values
(set to 1024). Given that the ipv4 and ipv6 routing caches are sized
dynamically at boot time, the static selections can be non-sensical.
This patch dynamically selects an appropriate gc threshold based on
the corresponding main routing table size, using the assumption that
we should in the worst case be able to handle as many connections as
the routing table can.
For ipv4, the maximum route cache size is 16 * the number of hash
buckets in the route cache. Given that xfrm4 starts garbage
collection at the gc_thresh and prevents new allocations at 2 *
gc_thresh, we set gc_thresh to half the maximum route cache size.
For ipv6, its a bit trickier. there is no maximum route cache size,
but the ipv6 dst_ops gc_thresh is statically set to 1024. It seems
sane to select a simmilar gc_thresh for the xfrm6 code that is half
the number of hash buckets in the v6 route cache times 16 (like the v4
code does).
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If arp_format_neigh_entry() can be called with n->dev->addr_len == 0, then a
write to hbuffer[-1] occurs.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no reason for the arbitrary restriction that device must be
up to create a vlan. This patch was added to Vyatta kernel to resolve startup
ordering issues where vlan's are created but real device was disabled.
Note: the vlan already correctly inherits the operstate from real device; so
if vlan is created and real device is marked down, the vlan is marked
down.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The test on map4 should be a test on map6.
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@
expression *x;
identifier f;
constant char *C;
@@
x = \(kmalloc\|kcalloc\|kzalloc\)(...);
... when != x == NULL
when != x != NULL
when != (x || ...)
(
kfree(x)
|
f(...,C,...,x,...)
|
*f(...,x,...)
|
*x->f
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The DCCP protocol tries to allocate some large hash tables during
initialisation using the largest size possible. This can be larger than
what the page allocator can provide so it prints a warning. However, the
caller is able to handle the situation so this patch suppresses the
warning.
Signed-off-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Finally! This is what you've all been waiting for!
This patch makes cfg80211 take care of wext emulation
_completely_ by itself, drivers that don't need things
cfg80211 doesn't do yet don't even need to be aware of
wireless extensions.
This means we can also clean up mac80211's and iwm's
Kconfig and make it possible to build them w/o wext
now!
RIP wext.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have handlers IWESSID for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since we now have IWAP handlers for all modes, we can
combine them into one.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Until now we implemented iwfreq for managed mode, we
needed to keep the implementations separate, but now
that we have all versions implemented we can combine
them and export just one handler.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When enqueuing packets on the internal packet queue, we
need to ensure that we have a valid vif pointer since
that is required since the net namespace work. Add some
assertions to verify this, but also don't crash is for
some reason we don't end up with a vif pointer -- warn
and drop the packet in all these cases.
Since this code touches a number of hotpaths, it is
intended to be temporary, or maybe configurable in the
future, at least the bit that is in the path that gets
hit for every packet, ieee80211_tx_pending().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When trying to disassociate while not associated,
the kernel would crash rather than refusing the
operation, fix this;
Reported-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an oops in ieee80211_scan_state_set_channel which was triggered
if the last scanned channel was skipped (for example due to regulatory
restrictions) by returning to the decision state after each skipped
channel.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jouni and Maxim reported an oops when using wpa_supplicant -Dnl80211,
which seems to be due to random data being contained in the crypto
settings for the assoc() command. This seems to be due to the missing
memset here, so add it -- it's certainly missing but I'm not 100%
certain that it will fix the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Marcel reported a warning, which quite obviously comes
from an oversight in the code handling deauth frames,
and which resulted in multiple follow-up warnings due
to this missing handling. This patch adds the missing
deauth handling (telling cfg80211 about it) and also
removes the follow-up warnings since they could happen
due to races even if nothing is wrong. I've explained
the races in the comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Marcel Holtmann <marcel@holtmann.org>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Luis reported this lockdep complaint, that he had also
reported earlier but when trying to analyse I had been
locking at the wrong code, and never saw the problem:
(slightly abridged)
=======================================================
[ INFO: possible circular locking dependency detected ]
2.6.31-rc4-wl #6
-------------------------------------------------------
wpa_supplicant/3799 is trying to acquire lock:
(cfg80211_mutex){+.+.+.}, at: [<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
but task is already holding lock:
(rtnl_mutex){+.+.+.}, at: [<ffffffff81400ff2>] rtnl_lock+0x12/0x20
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #1 (rtnl_mutex){+.+.+.}:
[<ffffffff810857b6>] __lock_acquire+0xd76/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffff81400ff2>] rtnl_lock+0x12/0x20
[<ffffffffa009f6a5>] nl80211_send_reg_change_event+0x1f5/0x2a0 [cfg80211]
[<ffffffffa009529e>] set_regdom+0x28e/0x4c0 [cfg80211]
-> #0 (cfg80211_mutex){+.+.+.}:
[<ffffffff8108587b>] __lock_acquire+0xe3b/0x12b0
[<ffffffff81085dd3>] lock_acquire+0xe3/0x120
[<ffffffff814ee7a4>] mutex_lock_nested+0x44/0x350
[<ffffffffa009246a>] cfg80211_get_dev_from_ifindex+0x1a/0x90 [cfg80211]
[<ffffffffa009813f>] get_rdev_dev_by_info_ifindex+0x6f/0xa0 [cfg80211]
[<ffffffffa009b12b>] nl80211_set_interface+0x3b/0x260 [cfg80211]
When looking at the correct code, the problem is quite
obvious. I'm not entirely sure which code paths lead
here, so until I can analyse it better let's just use
RCU to avoid the problem.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Jan reported that his b43-based laptop hangs during suspend.
The problem turned out to be mac80211 asking the driver to
stop the hardware before removing interfaces, and interface
removal caused b43 to touch the hardware (while down, which
causes the hang).
This patch fixes mac80211 to do reorder these operations to
have them in the correct order -- first remove interfaces
and then stop the hardware. Some more code is necessary to
be able to do so in a race-free manner, in particular it is
necessary to not process frames received during quiescing.
Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13337.
Reported-by: Jan Scholz <scholz@fias.uni-frankfurt.de>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (45 commits)
cnic: Fix ISCSI_KEVENT_IF_DOWN message handling.
net: irda: init spinlock after memcpy
ixgbe: fix for 82599 errata marking UDP checksum errors
r8169: WakeOnLan fix for the 8168
netxen: reset ring consumer during cleanup
net/bridge: use kobject_put to release kobject in br_add_if error path
smc91x.h: add config for Nomadik evaluation kit
NET: ROSE: Don't use static buffer.
eepro: Read buffer overflow
tokenring: Read buffer overflow
at1700: Read buffer overflow
fealnx: Write outside array bounds
ixgbe: remove unnecessary call to device_init_wakeup
ixgbe: Don't priority tag control frames in DCB mode
ixgbe: Enable FCoE offload when DCB is enabled for 82599
net: Rework mdio-ofgpio driver to use of_mdio infrastructure
register at91_ether using platform_driver_probe
skge: Enable WoL by default if supported
net: KS8851 needs to depend on MII
be2net: Bug fix in the non-lro path. Size of received packet was not updated in statistics properly.
...
This was caused by patch:
"mac80211: cooperate more with network namespaces"
The version of the patch applied doesn't match Johannes' latest:
http://johannes.sipsolutions.net/patches/kernel/all/LATEST/NNN-mac80211-netns.patch
The skb->cb virtual interface data wasn't being reset for
reuse so ath9k pooped out when trying to dereference the
private rate control info from the skb.
BUG: unable to handle kernel NULL pointer dereference
RIP: 0010:[<ffffffffa0258173>] ath_tx_rc_status+0x33/0x150 [ath9k]
<-- snip etc -->
Reported-by: Davide Pesavento <davidepesa@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a station queries us for a PS-poll response, we wrongly
queue the frame on the virtual interface's queue rather than
the pending queue.
Additionally, fix a race condition where we could potentially
send multiple frames to the sleeping station due to using a
station flag rather than a packet flag. When converting to a
packet flag, we can also convert p54 and remove the filter
clearing we added for it.
(Also remove a now dead function)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Bob Copeland <me@bobcopeland.com>
Tested-by: Bob Copeland <me@bobcopeland.com>
Cc: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were issuing probe requests to the associated AP on the wrong
band by having our beacon timer loss trigger while we are scanning.
When we would scan the timer could hit and force us to send a
probe request to the AP but with a chance we'd be on the wrong band.
This leads to finding no usable bitrate but we should not get so
far on the xmit path. We should not be trying to send these probe
request frames so prevent ieee80211_mgd_probe_ap() from sending
these.
As it turns out all callers of ieee80211_mgd_probe_ap() need this
check so we just move the scan check there. This means we can remove
the recenlty added check during ieee80211_sta_monitor_work().
Additionally we now fix a race condition added by the patch
"mac80211: do not monitor the connection while scanning" which
had the same check in ieee80211_sta_conn_mon_timer(). The race
happens because the timer routine *does* a valid check for
scanning but after it queues work into the mac80211 workqueue
the work callback can kick off with scanning enabled and cause
the same issue we were trying to avoid.
The more appropriate solution would be to disable the respective
timers during scan and re-enable them after scan but requires more
complex code and testing.
Cc: Christian Lamparter <chunkeey@web.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Reported-by: Fabio Rossi <rossi.f@inwind.it>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When a new MLME work is created, its timeout is initialised
to 0. This is wrong, it could then be thought of as having
an actual timeout in the future (time_is_after_jiffies() can
return true). Instead, it should be initialised to jiffies
so that it will run right away as soon as the mlme work is
executed.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Reported-by: Luciano Roth Coelho <luciano.coelho@nokia.com>
Reported-by: Alban Browaeys <prahal@yahoo.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Using background scanning in mac80211 the time a scan needs to
finish can exceed 10 seconds. Hence, increase the scan results
expire time to 15 seconds which should be sufficient.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Rename scan_state to next_scan_state to better reflect
what it is used for.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan flag "SCAN_OFF_CHANNEL" which basically tells us
that we are currently on a different channel for scanning and cannot
RX/TX. "SCAN_SW_SCANNING" tells us that we are currently running a
software scan but we might as well be on the operating channel to RX/TX.
While "SCAN_SW_SCANNING" is set during the whole scan "SCAN_OFF_CHANNEL"
is set when leaving the operating channel and unset when coming back.
Introduce two new scan states "SCAN_LEAVE_OPER_CHANNEL" and
"SCAN_ENTER_OPER_CHANNEL" which basically implement the functionality we
need to leave the operating channel (send a nullfunc to the AP and stop
the queues) and enter it again (send a nullfunc to the AP and start the
queues again).
Enhance the scan state "SCAN_DECISION" to switch back to the operating
channel after each scanned channel. In the future it sould be simple
to enhance the decision state to scan as much channels in a row as the
qos latency allows us.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use a bitfield to store the current scan mode instead of two boolean
variables {sw,hw}_scanning. This patch does not introduce functional
changes but allows us to enhance the scan flags later (for example
for background scanning).
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Introduce a new scan state "decision" which is entered after
every completed scan operation and decides about the next steps.
At first the decision is in any case to scan the next channel.
This shouldn't introduce any functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of queueing the scan work again without delay just process the
next state immediately.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move the processing of each scan state into its own functions for better
readability. This patch does not introduce functional changes.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This finally opens up the ability to put mac80211 devices
into different network namespaces. As long as you don't
have sysfs, that is.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to make cfg80211/nl80211 aware of network namespaces,
we have to do the following things:
* del_virtual_intf method takes an interface index rather
than a netdev pointer - simply change this
* nl80211 uses init_net a lot, it changes to use the sender's
network namespace
* scan requests use the interface index, hold a netdev pointer
and reference instead
* we want a wiphy and its associated virtual interfaces to be
in one netns together, so
- we need to be able to change ns for a given interface, so
export dev_change_net_namespace()
- for each virtual interface set the NETIF_F_NETNS_LOCAL
flag, and clear that flag only when the wiphy changes ns,
to disallow breaking this invariant
* when a network namespace goes away, we need to reparent the
wiphy to init_net
* cfg80211 users that support creating virtual interfaces must
create them in the wiphy's namespace, currently this affects
only mac80211
The end result is that you can now switch an entire wiphy into
a different network namespace with the new command
iw phy#<idx> set netns <pid>
and all virtual interfaces will follow (or the operation fails).
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are still two places in mac80211 that hardcode
the initial net namespace (init_net). One of them is
mandated by cfg80211 and will be removed by a separate
patch, the other one is used for finding the network
device of a pending packet via its ifindex.
Remove the latter use by keeping track of the device
pointer itself, via the vif pointer, and avoid it
going stale by dropping pending frames for a given
interface when the interface is removed.
To keep track of the vif pointer for the correct
interface, change the info->control.vif pointer's
internal use to always be the correct vif, and only
move it to the vif the driver expects (or NULL for
monitor interfaces and injected packets) right before
giving the packet to the driver.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Export garbage collector thresholds for xfrm[4|6]_dst_ops
Had a problem reported to me recently in which a high volume of ipsec
connections on a system began reporting ENOBUFS for new connections
eventually.
It seemed that after about 2000 connections we started being unable to
create more. A quick look revealed that the xfrm code used a dst_ops
structure that limited the gc_thresh value to 1024, and always
dropped route cache entries after 2x the gc_thresh.
It seems the most direct solution is to export the gc_thresh values in
the xfrm[4|6] dst_ops as sysctls, like the main routing table does, so
that higher volumes of connections can be supported. This patch has
been tested and allows the reporter to increase their ipsec connection
volume successfully.
Reported-by: Joe Nall <joe@nall.com>
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
ipv4/xfrm4_policy.c | 18 ++++++++++++++++++
ipv6/xfrm6_policy.c | 18 ++++++++++++++++++
2 files changed, 36 insertions(+)
Signed-off-by: David S. Miller <davem@davemloft.net>
entry was tested for NULL near the beginning of the function, followed by a
return, and there is no intervening modification of its value.
A simplified version of the semantic match that finds this problem is as
follows: (http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@r exists@
local idexpression x;
expression E;
position p1,p2;
@@
if (x == NULL || ...) { ... when forall
return ...; }
... when != \(x=E\|x--\|x++\|--x\|++x\|x-=E\|x+=E\|x|=E\|x&=E\|&x\)
(
*x == NULL
|
*x != NULL
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
irttp_dup() copies a tsap_cb struct, but does not initialize the
spinlock in the new structure, which confuses lockdep.
Signed-off-by: Deepak Saxena <dsaxena@mvista.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/phonet/pn_dev.c: In function `phonet_device_get':
net/phonet/pn_dev.c:99: warning: 'dev' might be used uninitialized in this function
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This helps avoid error messages with ethtool -k on devices that
don't provide device specific routines.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
------------------------------------------------------------------
Signed-off-by: David S. Miller <davem@davemloft.net>
kobject_init_and_add will alloc memory for kobj->name, so in br_add_if
error path, simply use kobject_del will not free memory for kobj->name.
Fix by using kobject_put instead, kobject_put will internally calls
kobject_del and frees memory for kobj->name.
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The use of a static buffer in rose2asc() to return its result is not
threadproof and can result in corruption if multiple threads are trying
to use one of the procfs files based on rose2asc().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Oliver Hartkopp:
net/phonet/pn_dev.c: In function ‘phonet_init_net’:
net/phonet/pn_dev.c:221: error: implicit declaration of function
‘proc_net_fops_create’
net/phonet/pn_dev.c: In function ‘phonet_exit_net’:
net/phonet/pn_dev.c:242: error: implicit declaration of function ‘proc_net_remove’
Signed-off-by: David S. Miller <davem@davemloft.net>
The removal of the master netdev broke the mesh forwarding path. This patch
fixes it by using the new internal 'pending' queue.
As a result of this change, mesh forwarding no longer does the inefficient
802.11 -> 802.3 -> 802.11 conversion that was done before.
[Changes since v1]
Suggested by Johannes:
- Select queue before adding to mpath queue
- ieee80211_add_pending_skb -> ieee80211_add_pending_skbs
- Remove unnecessary header wme.h
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_xmit() cannot be called with tasklets enabled
because it is normally called from within a tasklet.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 required this due to the master netdev, but now
it can put all information into skb->cb and this can go.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the internal 'pending' queue system in place, we can simply
put packets there instead of pushing them off to the master dev,
getting rid of the master interface completely.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For mac80211, with the master netdev removal, we need to be
able to sync a multicast address list onto another list that
is not tracked within a netdev, so we need access to the
functions doing that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In cfg80211_upload_connect_keys(), we call add_key, set_default_key
and set_default_mgmt_key (if applicable) one by one. If one of these
operations fails, we should stop calling the following functions.
Because if the key is not added successfully, we should not set it as
default key anyway.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We invoke the cfg80211 set_default_key callback only for WEP key
configuring.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following errors:
driver-trace.h:148:1: error: cannot size expression
driver-trace.h:148:1: error: cannot size expression
[...]
driver-trace.h:222:1: error: cannot size expression
driver-trace.h:71:1: error: incompatible types for operation (<)
driver-trace.h:71:1: left side has type void *<noident>
driver-trace.h:71:1: right side has type int
driver-trace.h:99:1: error: incompatible types for operation (<)
driver-trace.h:99:1: left side has type void *<noident>
driver-trace.h:99:1: right side has type int
driver-trace.h:148:1: error: incompatible types for operation (<)
driver-trace.h:148:1: left side has type void *<noident>
driver-trace.h:148:1: right side has type int
driver-trace.h:222:1: error: cannot size expression
driver-trace.h:248:1: error: incompatible types for operation (<)
driver-trace.h:248:1: left side has type void *<noident>
driver-trace.h:248:1: right side has type int
driver-trace.h:446:1: error: incompatible types for operation (<)
driver-trace.h:446:1: left side has type void *<noident>
driver-trace.h:446:1: right side has type int
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
mac80211 constantly monitors the connection to the associated AP
in order to check if it is out of reach/dead.
This is absolutely fine most of the time.
Except when there is a scheduled scan for the whole neighborhood.
After all this path could trigger while scanning on different channel.
Or even worse: this AP probing triggers a WARN_ON in rate_lowest_index
when the scan code did a band transition!
( http://www.kerneloops.org/raw.php?rawid=449304 )
Reported-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Christian Lamparter <chunkeey@web.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the wext code I tried to not reconnect all the time
when the user wasn't really sure what they were doing,
like setting the BSSID back to the same value it was.
However, this optimisation should only be done while
associated so that setting the BSSID back to the same
value that it was actually triggers a new association
if not currently associated. To achieve, that, put the
relevant code into the !IDLE case instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-by: Kalle Valo <kalle.valo@iki.fi>
Tested-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_sme_scan_done() can be called (by fullmac cards) with
wdev->conn == NULL when CFG80211_SME_CONNECTING. We quit silently
instead of WARN_ON in this case.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We were treating ieee80211_regdom module parameter hints
as core hints, this means we were not letting the user help
compliance further when using the module parameter. It also
meant that users with a device with a custom regulatory
domain set (wiphy->custom_regulatory) using this module
parameter were being stuck to the original default core
static regualtory domain. We fix this by using the static
cfg80211_regdomain alpha2 as the core hint and treating the
module parameter separately.
All iwlwifi and ath5k/ath9k/ar9170 devices which world roam
set the wiphy->custom_regulatory. This change allows users
using this module parameter to have it trated as a a proper
user hint and not have it ignored.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All current rate control algorithms agree to send management and no-ack
frames at the lowest rate. They also agree to do this when sta
and the private rate control data is NULL. We add a hlper to mac80211
for this and simplify the rate control algorithm code.
Developers wishing to make enhancements to rate control algorithms
are for broadcast/multicast can opt to not use this in their
gate_rate() mac80211 callback.
Cc: Zhu Yi <yi.zhu@intel.com>
Acked-by: Reinette Chatre <reinette.chatre@intel.com>
Cc: ipw3945-devel@lists.sourceforge.net
Cc: Gabor Juhos <juhosg@openwrt.org>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: Felix Fietkau <nbd@openwrt.org>
Cc: Derek Smithies <derek@indranet.co.nz>
Cc: Chittajit Mitra <Chittajit.Mitra@Atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we're associated we should be able to send data to
target sta. If we cannot we may be trying to use the incorrect
band to talk to the sta. Lets catch any such cases, warn, and
drop the frames to not invalidate assumptions being made on
rate control algorithms when they have a valid sta to
communicate with. Any such cases should be handled and fixed.
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The work that we cancel there requires the cfg80211_mutex,
so we can't cancel it under the mutex, which is fine, we
can just move it to after the locked section.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In "mac80211: monitor the connection" I forgot to
add code to cancel the new timers & work when the
interface is brought down, which isn't a problem
if you just bring it down, but _is_ a problem when
you destroy the interface. Correct this lapse.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_set_wpa_version completely missed the use case when disabling
WPA, considering IW_AUTH_WPA_VERSION_DISABLED an invalid argument. This
caused weird error messages in wpa_supplicant.
Signed-off-by: Gábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "what-was-I-thinking-if-anything" patch. Clearly,
if cfg80211_send_disassoc() does wdev_lock() and then
calls __cfg80211_send_disassoc(), the latter shouldn't
lock again. And the sme_state test is ... no further
comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When connected to a BSS, or joined to an IBSS, we'll want
to know in userspace without using wireless extensions, so
report the BSS status in the BSS list. Userspace can query
the BSS list, display all the information and retrieve the
station information as well.
For example (from hwsim):
$ iw dev wlan1 scan dump
BSS 02:00:00:00:00:00 (on wlan1) -- associated
freq: 2462
beacon interval: 100
capability: ESS ShortSlotTime (0x0401)
signal: -50.00 dBm
SSID: j
Supported rates: 1.0* 2.0* 5.5* 11.0* 6.0 9.0 12.0 18.0
DS Paramater set: channel 11
ERP: <no flags>
Extended supported rates: 24.0 36.0 48.0 54.0
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Pavel reported that you can't set the SSID from "foo" to
"bar". I tried reproducing, but used different values,
with different lengths, and thus never saw the obvious
problem.
Reported-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This variable is only used internally, _while_ connected.
If we use it, the sequence
# iwconfig wlan1 essid foo
<connects>
# iwconfig wlan1 essid ""
<disconnects>
# iwconfig
will still display "foo" as the SSID afterwards, which
is obviously quite bogus. Fix this by only displaying
the wext SSID, if present.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Instead of using the wext BSSID which may be NULL if
you haven't explicitly set one, we should instead use
the current_bss pointer -- if that's NULL we aren't
connected anyway. Fixes missing signal quality output
reported to me internally at Intel.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
1) there's a spin_lock() that needs to be spin_lock_bh()
2) action frames of size 24 might cause an out-of-bounds
memory access (for the 25th byte only, so no big deal)
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The cfg80211_sme_disassoc() function is already holding
a lock here that cfg80211_mlme_deauth() would take, so
it needs to use __cfg80211_mlme_deauth() instead.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the recent MLME rework I accidentally removed the connection
monitoring code. In order to add it back, this patch will add new
code to monitor both for beacon loss and for the connection actually
working, with possibly separate triggers.
When no unicast frames have been received from the AP for (currently)
two seconds, we will send the AP a probe request. Also, when we don't
see beacons from the AP for two seconds, we do the same (but those
times need not be the same due to the way the code is now written).
Additionally, clean up the parameters to the ieee80211_set_disassoc()
function that I need here, those are all useless except sdata.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We have, sometimes, multiple things that want to
run but don't have their own timer. Introduce a
new function to mac80211's mlme run_again() that
makes sure that the timer will run again at the
_first_ needed time, use that function and also
properly reprogram the timer once it fired.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch avoids memcpy from wdev->wext.ibss.bssid if it is NULL.
This could happen if we SIOCGIWAP before SIOCSIWAP.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This reworks the key operation in cfg80211, and now only
allows, from userspace, configuring keys (via nl80211)
after the connection has been established (in managed
mode), the IBSS been joined (in IBSS mode), at any time
(in AP[_VLAN] modes) or never for all the other modes.
In order to do shared key authentication correctly, it
is now possible to give a WEP key to the AUTH command.
To configure static WEP keys, these are given to the
CONNECT or IBSS_JOIN command directly, for a userspace
SME it is assumed it will configure it properly after
the connection has been established.
Since mac80211 used to check the default key in IBSS
mode to see whether or not the network is protected,
it needs an update in that area, as well as an update
to make use of the WEP key passed to auth() for shared
key authentication.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We will soon want to nest key attributes into
some new attribute for configuring static WEP
keys at connect() and ibss_join() time, so we
need nested attributes for that. However, key
attributes right now are 'global'. This patch
thus introduces new nested attributes for the
key settings and functions for parsing them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Assign next hop address to pending mesh frames once the path is resolved.
Regression. Frames transmitted when a mesh path was wating to be resolved were
being transmitted with an invalid Receiver Address.
[Changes since v1]
Suggested by Johannes:
- Improved frame_queue traversal
- Narower RCU scope
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fixes two small bugs:
1) the connect variable is already initialised, and the
assignment to auth_type overwrites the previous setting
with a wrong value
2) when all authentication attempts fail, we need to report
that we couldn't connect
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
cfg80211_wext_giwrate doesn't lock the wdev, so it
cannot access current_bss race-free. Also, there's
little point in trying to ask the driver for an AP
that it never told us about, so avoid that case.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This makes mac80211 use the event tracing framework
to log all operations as given to the driver. This
will need to be extended with more information, but
as a start it should be good.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_testmode_cmd can very well be static.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While looking for something else I spent some time adding
one liner comments to the tcp_output.c functions that
didn't have any. That makes the comments more consistent.
I hope I documented everything right.
No code changes.
v2: Incorporated feedback from Ilpo.
v3: Change style of one liner comments, add a few more comments.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some style cleanups to match current code practices.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The per-socket drop count is visible via /proc/net/phonet.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This provides a list of sockets with their Phonet bind addresses and
some socket debug informations through /proc/net/phonet.
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
include/net/ieee802154/af_ieee802154.h (and others) naming seems to be too long
and redundant. Drop one level of subdirectories.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (37 commits)
sky2: Avoid races in sky2_down
drivers/net/mlx4: Adjust constant
drivers/net: Move a dereference below a NULL test
drivers/net: Move a dereference below a NULL test
connector: maintainer/mail update.
USB host CDC Phonet network interface driver
macsonic, jazzsonic: fix oops on module unload
macsonic: move probe function to .devinit.text
can: switch carrier on if device was stopped while in bus-off state
can: restart device even if dev_alloc_skb() fails
can: sja1000: remove duplicated includes
New device ID for sc92031 [1088:2031]
3c589_cs: re-initialize the multicast in the tc589_reset
Fix error return for setsockopt(SO_TIMESTAMPING)
netxen: fix thermal check and shutdown
netxen: fix deadlock on dev close
netxen: fix context deletion sequence
net: Micrel KS8851 SPI network driver
tcp: Use correct peer adr when copying MD5 keys
tcp: Fix MD5 signature checking on IPv4 mapped sockets
...
The local variable 'idev' shadows the function argument 'idev' to
ip6_mc_add_src(). Fixed by removing the local declaration, as pmc->idev
should be identical with 'idev' passed as argument.
Signed-off-by: Gerrit Renker <gerrit@erg.abdn.ac.uk>
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Potential memory leak via msg pointer in nl80211_get_key() function.
Signed-off-by: Niko Jokinen <ext-niko.k.jokinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For forwarded frames, we save the precursor address in addr1 in case it
needs to be used to send a Path Error. mesh_path_discard_frame,
however, was using addr2 instead of addr1 to send Path Error frames, so
correct that and also make the comment regarding this more clear.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The point of this function is to set the software and hardware state at
the same time. When I tried to use it, I found it was only setting the
software state.
Signed-off-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Reviewed-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The location of the 802.11 header is calculated incorrectly due to a
wrong placement of parentheses. Found by kmemcheck.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Apparently there actually _are_ tools that try to set
this in sysfs even though it wasn't supposed to be used
this way without claiming first. Guess what: now that
I've cleaned it all up it doesn't matter and we can
simply allow setting the soft-block state in sysfs.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Tested-By: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
My kvm instance was complaining a lot about sleeping
in atomic contexts in the mesh code, and it turns out
that both mesh_path_add() and mpp_path_add() need to
be able to sleep (they even use synchronize_rcu()!).
I put in a might_sleep() to annotate that, but I see
no way, at least right now, of actually making sure
those functions are only called from process context
since they are both called during TX and RX and the
mesh code itself even calls them with rcu_read_lock()
"held".
Therefore, let's disable it completely for now.
It's possible that I'm only seeing this because the
hwsim's beaconing is broken and thus the peers aren't
discovered right away, but it is possible that this
happens even if beaconing is working, for a peer that
doesn't exist or so.
It should be possible to solve this by deferring the
freeing of the tables to call_rcu() instead of using
synchronize_rcu(), and also using atomic allocations,
but maybe it makes more sense to rework the code to
not call these from atomic contexts and defer more of
the work to the workqueue. Right now, I can't work on
either of those solutions though.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I guess it should be -EINVAL rather than EINVAL. I have not checked
when the bug came in. Perhaps a candidate for -stable?
Signed-off-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a comment for what's going on. Remove negative logic.
I find this much easier to understand quickly, although
there are a few lines duplicated.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The existing code treated page_shift as a variable, when in fact we
always want to have the fastreg page size be the same as the arch's
page size -- and it is, so this doesn't need to be a variable.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While FMRs allow significant flexibility in what size of pages they can use,
we really just want FMR pages to match CPU page size. Roland says we can
count on this always being supported, so this simplifies things.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Completion or congestion notifications were not being checked
if the socket went to sleep. This patch fixes that.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Backwards compatibility with rds 3.0 causes protocol-
based flow control to be disabled as a side-effect.
I don't want to pull out FC support from the IB transport
but I do want to document and keep the sysctl consistent
if possible.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since RDS 3.0 and 3.1 have different packet formats,
we need to wait until after protocol negotiation
is complete to layout the rx buffers.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Protocol negotiation is logically a property of the
transports, so rds core need not set it.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Of course len is in bytes. Calling it data_len hopefully indicates
a little better what the variable is actually for.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The big differences between RDS 3.0 and 3.1 are protocol-level
flow control, and with 3.1 the header is in front of the data. The header
always ends up in the header buffer, and the data goes in the data page.
In 3.0 our "header" is a trailer, and will end up either in the data
page, the header buffer, or split across the two. Since 3.1 is backwards-
compatible with 3.0, we need to continue to support these cases. This
patch does that -- if using RDS 3.0 wire protocol, it will copy the header
from wherever it ended up into the header buffer.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RDS on IB uses privdata to do protocol version negotiation. Apparently
the IB stack will return a larger privdata buffer than the struct we were
expecting. Just to be extra-sure, this patch adds some checks in this area.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be default cause IB connections to failover faster,
but allow a longer retry count to be used if desired.
Signed-off-by: Andy Grover <andy.grover@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the TCP connection handshake completes on the passive
side, a variety of state must be set up in the "child" sock,
including the key if MD5 authentication is being used. Fix TCP
for both address families to label the key with the peer's
destination address, rather than the address from the listening
sock, which is usually the wildcard.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix MD5 signature checking so that an IPv4 active open
to an IPv6 socket can succeed. In particular, use the
correct address family's signature generation function
for the SYN/ACK.
Reported-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While looking for other fib_trie problems reported by Pawel Staszewski
I noticed there are a few uses of tnode_get_child() and node_parent()
in lookups instead of their rcu versions.
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
During large updates there could be triggered warnings like: "Fix
inflate_threshold_root. Now=25 size=11 bits" if inflate() of the root
node isn't finished in 10 loops. It should be much rarer now, after
changing the threshold from 15 to 25, and a temporary problem, so
this patch tries to handle it automatically using a fix variable to
increase by one inflate threshold for next root resizes (up to the 35
limit, max fix = 10). The fix variable is decreased when root's
inflate() finishes below 7 loops (even if some other, smaller table/
trie is updated -- for simplicity the fix variable is global for now).
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Reported-by: Jorge Boncompte [DTI2] <jorge@dti2.net>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: Robert Olsson <robert.olsson@its.uu.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
During trie_rebalance() we free memory after resizing with call_rcu(),
but large updates, especially with PREEMPT_NONE configs, can cause
memory stresses, so this patch calls synchronize_rcu() in
tnode_free_flush() after each sync_pages to guarantee such freeing
(especially before resizing the root node).
The value of sync_pages = 128 is based on Pawel Staszewski's tests as
the lowest which doesn't hinder updating times. (For testing purposes
there was a sysfs module parameter to change it on demand, but it's
removed until we're sure it could be really useful.)
The patch is based on suggestions by: Paul E. McKenney
<paulmck@linux.vnet.ibm.com>
Reported-by: Pawel Staszewski <pstaszewski@itcare.pl>
Tested-by: Pawel Staszewski <pstaszewski@itcare.pl>
Signed-off-by: Jarek Poplawski <jarkao2@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the physical MTU changes we want to ensure that all existing
VLAN device MTUs do not exceed the new underlying MTU. This patch
adds that propagation.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e912b1142b
(net: sk_prot_alloc() should not blindly overwrite memory)
took care of not zeroing whole new socket at allocation time.
sock_copy() is another spot where we should be very careful.
We should not set refcnt to a non null value, until
we are sure other fields are correctly setup, or
a lockless reader could catch this socket by mistake,
while not fully (re)initialized.
This patch puts sk_node & sk_refcnt to the very beginning
of struct sock to ease sock_copy() & sk_prot_alloc() job.
We add appropriate smp_wmb() before sk_refcnt initializations
to match our RCU requirements (changes to sock keys should
be committed to memory before sk_refcnt setting)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a slab cache uses SLAB_DESTROY_BY_RCU, we must be careful when allocating
objects, since slab allocator could give a freed object still used by lockless
readers.
In particular, nf_conntrack RCU lookups rely on ct->tuplehash[xxx].hnnode.next
being always valid (ie containing a valid 'nulls' value, or a valid pointer to next
object in hash chain.)
kmem_cache_zalloc() setups object with NULL values, but a NULL value is not valid
for ct->tuplehash[xxx].hnnode.next.
Fix is to call kmem_cache_alloc() and do the zeroing ourself.
As spotted by Patrick, we also need to make sure lookup keys are committed to
memory before setting refcount to 1, or a lockless reader could get a reference
on the old version of the object. Its key re-check could then pass the barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Add appropriate MODULE_ALIAS() to facilitate autoloading of can protocol drivers
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a use after free bug in can protocol drivers
The release functions of the can protocol drivers lack a call to
sock_orphan() which leads to referencing freed memory under certain
circumstances.
This patch fixes a bug reported here:
https://lists.berlios.de/pipermail/socketcan-users/2009-July/000985.html
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Acked-by: Oliver Hartkopp <oliver@hartkopp.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wireless extensions have the unfortunate problem that events
are multicast netlink messages, and are not independent of
pointer size. Thus, currently 32-bit tasks on 64-bit platforms
cannot properly receive events and fail with all kinds of
strange problems, for instance wpa_supplicant never notices
disassociations, due to the way the 64-bit event looks (to a
32-bit process), the fact that the address is all zeroes is
lost, it thinks instead it is 00:00:00:00:01:00.
The same problem existed with the ioctls, until David Miller
fixed those some time ago in an heroic effort.
A different problem caused by this is that we cannot send the
ASSOCREQIE/ASSOCRESPIE events because sending them causes a
32-bit wpa_supplicant on a 64-bit system to overwrite its
internal information, which is worse than it not getting the
information at all -- so we currently resort to sending a
custom string event that it then parses. This, however, has a
severe size limitation we are frequently hitting with modern
access points; this limitation would can be lifted after this
patch by sending the correct binary, not custom, event.
A similar problem apparently happens for some other netlink
users on x86_64 with 32-bit tasks due to the alignment for
64-bit quantities.
In order to fix these problems, I have implemented a way to
send compat messages to tasks. When sending an event, we send
the non-compat event data together with a compat event data in
skb_shinfo(main_skb)->frag_list. Then, when the event is read
from the socket, the netlink code makes sure to pass out only
the skb that is compatible with the task. This approach was
suggested by David Miller, my original approach required
always sending two skbs but that had various small problems.
To determine whether compat is needed or not, I have used the
MSG_CMSG_COMPAT flag, and adjusted the call path for recv and
recvfrom to include it, even if those calls do not have a cmsg
parameter.
I have not solved one small part of the problem, and I don't
think it is necessary to: if a 32-bit application uses read()
rather than any form of recvmsg() it will still get the wrong
(64-bit) event. However, neither do applications actually do
this, nor would it be a regression.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current function for sending events first allocates the
event stream buffer, and then an skb to copy the event stream
into. This can be done in one go. Also, the current function
leaks kernel data to userspace in a 4 uninitialised bytes,
initialise those explicitly. Finally also add a few useful
comments, as opposed to the current comments.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes wireless extensions netns aware. The
tasklet sending the events is converted to a work
struct so that we can rtnl_lock() in it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a possible regression with p9_client_stat where it can try to kfree
an ERR_PTR after an erroneous p9pdu_readf. Also remove an unnecessary data
buffer increment in p9_client_read.
Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
The default 9p transport module is not chosen unless an option parameter (any)
is passed to mount, which thus returns a ENOPROTOSUPPORT. This fix moves the
check out of parse_opts into p9_client_create.
Signed-off-by: Abhishek Kulkarni <adkulkar@umail.iu.edu>
Signed-off-by: Eric Van Hensbergen <ericvh@gmail.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
Revert "NET: Fix locking issues in PPP, 6pack, mkiss and strip line disciplines."
skbuff.h: Fix comment for NET_IP_ALIGN
drivers/net: using spin_lock_irqsave() in net_send_packet()
NET: phy_device, fix lock imbalance
gre: fix ToS/DiffServ inherit bug
igb: gcc-3.4.6 fix
atlx: duplicate testing of MCAST flag
NET: Fix locking issues in PPP, 6pack, mkiss and strip line disciplines.
netdev: restore MTU change operation
netdev: restore MAC address set and validate operations
sit: fix regression: do not release skb->dst before xmit
net: ip_push_pending_frames() fix
net: sk_prot_alloc() should not blindly overwrite memory
Fixes two bugs:
- ToS/DiffServ inheritance was unintentionally activated when using impair fixed ToS values
- ECN bit was lost during ToS/DiffServ inheritance
Signed-off-by: Andreas Jaggi <aj@open.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename lookup_neigh_params to lookup_neigh_parms as the struct is named
neigh_parms and all other functions dealing with the struct carry
neigh_parms in their names.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove redundant sched/ in net/Makefile.
sched/ is contained in previous:
obj-$(CONFIG_NET) += ethernet/ 802/ sched/ netlink/,
so the later
obj-$(CONFIG_NET_SCHED) += sched/
isn't necessary.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
----
Makefile | 1 -
1 file changed, 1 deletion(-)
Signed-off-by: David S. Miller <davem@davemloft.net>
