Due to legacy reason, dating back to when the wl1251 and wl1271 still were
a unified driver, some work-structures are initialized on hardware startup.
The hardware recovery code creates a scenario in which it is possible for a
workstruct to be re-initialized while the work-function itself is running,
which causes a kernel WARNing and a subsequent reboot.
To remedy this, move the work initialization calls to the hw allocation,
which is the logically correct place for them anyway.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Instead of sending one packet at a time to the firmware, try to
send all available packets at once.
This optimization decreases the number of transactions, which saves
CPU cycles and increases network throughput.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Instead of retrieving one packet at a time from the firmware, try to
retrieve all available packets at once.
This optimization decreases the number of transactions, which saves
CPU cycles and increases network throughput.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The HW supports up to 4095 bytes transfers via SPI. The SPI read & write
operations do not handle larger transfers, causing the HW to stall in such
cases.
Fix this by fragmenting large transfers into smaller chunks, and
transferring each one separately.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This patch improves connection reliability by choosing the lowest basic
rate for null-func frames (which increases their range, as the firmware does
not do rate fall-back for null-func frames.) Also, increase the PSM entry
retry-counter.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Tested-by: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently then dwell times for each channel in scans is set to an overly
long value, and excessive number of probe-requests are transmitted on each
channel (for active scans.)
Based on testing, comparable results can be received with smaller dwell-time,
and, with fever probe-requests - in fact, reducing the number of probe-requests
to 2 seems to increase the number of found results.
Configure more optimal values for per channel dwell times. Comparison for the
different scan configurations (in my current office environment):
dwell-time 60000 3x probe-req == ~60 results
40000 3x probe-req == ~50 results
30000 3x probe-req == ~40 results
dwell-time 60000 2x probe-req == ~70 results
40000 2x probe-req == ~60 results
30000 2x probe-req == ~58 results
The above are results for a cumulative 3 scan run. For individual scans, the
number of results drop slightly more.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Currently, the driver does not handle a failing hardware command to scan in
any way - effectively, the scan machine will jam until the driver is shut down,
and future scan requests will just return -EBUSY to user space, resulting in
a type of busy-loop. The same problem occurs if the firmware fails to deliver
the scan completion event - add timeout for this.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
There is some probability of hardware failures, which currently go largely
undetected. Attempt to recover from these failures by shutting down the
hardware, and requesting mac80211 to reconfigure it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Do this so the interface removal can be triggered from an upcoming hardware
failure recovery mechanism.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The work cancelling has had several hazards, ranging from potentially
executing work after the driver is in OFF state, to executing work after
the driver and relevant memory structures are already removed.
Fix these.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The current scan implementation can jam, if the scan request ends up
containing no work. This can especially happen if there is a scan request
with only 11a band channels for HW that does not support 11a.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Incorrect TID was configured for TX frames. This resulted in incorrect
queues to be used for classes in transmission.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This patch always enables 11a band towards the mac80211, but prevents scanning
(and hence the usage of) 11a band channels if the chipset does not support it.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This patch reduces the rate of the null-func used to enter PSM on the last
retry as precaution.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Instead of hardcoding 11a support, enable/disable driver support based on
the dual-mode-select parameter in the nvs-file general paramters.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The function is not used anywhere.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The current order causes driver releasing to fail in various ways, and causes
possible instability.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
This removes a fixme. Also, it removes a redundant setting of the wake-up
conditions when exiting power save mode, which should improve performance.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
The mac80211 inserts channels into a scan request in the same order the driver
registers them. Use this fact to optimize scan by ordering the channels so
that adjacent channels don't get scanned consecutively.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
When we get no SSIDs in the scan request, we should force a passive scan in
all channels. This patch adds code to force the passive scan flag to be set
in that case.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
This code was a leftover of the previous scanning mechanism. The if is
totally unnecessary, since both branches do the same thing.
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
In the scan state machine, the wl1271_mutex is unlocked first then relocked,
and then the scan state variables are modified.
This makes it possible for ieee80211_scan_complete to be called twice in some
scenarios, as the scan completion event from the firmware may be processed
while the mutex is unlocked.
To fix the issue, move the ieee80211_scan_complete call last in the function.
This is generally safer, but there still may be issues is functions calling
the scan state machine rely on states checked before the unlocking of the
global mutex.
(forward ported from 2.6.32 -- this is not strictly needed anymore, because
the mutex doesn't need to be unlocked anymore, but I'm applying this change
anyway, so that the call to ieee80211_scan_complete is in the same place)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Add a trigger to net_device changes to monitor for oper_state changes in order
to be able to inform the firmware when association is fully complete (including
the EAP negotiation.)
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Implement the command function to send CMD_SET_STA_STATE to the firmware. This
is used to indicate that association (and the related EAP negotiation) are
complete.
This is used to tune WLAN-BT coexistense priority towards BT, improving BT
A2DP and SCO performance.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Reviewed-by: Teemu Paasikivi <ext-teemu.3.paasikivi@nokia.com>
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
As of Rev. 6.1.0.0.335, the ACX_SET_SMART_REFLEX_DEBUG command is
deprecated. This patch removes it from the wl1271 driver (it wasn't used
anyway).
Signed-off-by: Luciano Coelho <luciano.coelho@nokia.com>
Reviewed-by: Saravanan Dhanabal <ext-saravanan.dhanabal@nokia.com>
The following commit removed splitmic. But forgot to add
ATH_CRYPT_CAP_MIC_COMBINED flag for HTC drivers which causes
TKIP to fail.
Author: Bruno Randolf <br1@einfach.org>
Date: Wed Sep 8 16:04:54 2010 +0900
ath/ath9k: Replace common->splitmic with a flag
Replace common->splitmic with ATH_CRYPT_CAP_MIC_COMBINED flag.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The old ieee80211_find_sta_by_hw method didn't properly
find VIFS when there was more than one per AP. This caused
AMPDU logic in ath9k to get the wrong VIF when trying to
account for transmitted SKBs.
This patch changes ieee80211_find_sta_by_hw to take a
localaddr argument to distinguish between VIFs with the
same AP but different local addresses. The method name
is changed to ieee80211_find_sta_by_ifaddr.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9287 v1.0 was never sold (and the initvals removed), its revision
checks can be simplified similar to AR9280
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9285 v1.0 and v1.1 were never sold (and the initvals removed),
its revision checks can be simplified similar to AR9280
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since AR9280 v1.0 was never sold (and the initvals removed), v1.0 specific
revision checks can be removed and the 'v2.0 or later' check can be
simplified to a check for AR9280 or later.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Due to miscalculation of nvs_len, excessive data was sent to the
firmware.
Fix this by first setting nvs_ptr to point to the first NVS table,
and computing the total size of all NVS tables accordingly.
Signed-off-by: Ido Yariv <ido@wizery.com>
Tested-By: Tuomas Katila <ext-tuomas.2.katila@nokia.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch ensures fair beacon distribution in IBSS mode
by configuring proper CWmin based on slot time.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Paprd needs to be done only on active chains(not for all the chains
that hw can support). The paprd training frames which are sent
for inactive chains would be hanging on the hw queue without
getting transmitted and would make the connection so unstable.
This issue happens only with the hw which supports paprd cal(ar9003).
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The "basic_rate" module option is not implemented correctly. If the
rate was set to zero it was supposed to set it to "basic_rate | 0x80".
Unfortunately the check to see if what zero was wrong and it checked
"!ai->config.rates" (which is always false) instead of
"!ai->config.rates[i]".
This option was just used for development and it wasn't documented
anywhere. Instead of fixing it, we can just remove it.
Reported-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k can use minstrel_ht instead, so it makes sense to save some space here.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
It is not used anywhere else and can be made static
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The tid aggregation cleanup is a bit fragile, as it discards failed
subframes in some places, and retransmits them in others. This could
block the cleanup of an existing aggregation session, if a retransmission
for a tid is issued, yet the tid is never scheduled again because of
the cleanup state.
Fix this by getting rid of as many subframes as possible, as early
as possible, and immediately transmitting pending subframes as regular
HT frames instead of waiting for the cleanup to complete.
Drop all pending subframes while keeping track of the Block ACK window
during aggregate tx completion to prevent sending out stale subframes,
which could confuse the receiver side.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A new aggregation session start can be issued by mac80211, even when the
cleanup of the previous session has not completed yet. Since the data structure
for the session is not recreated, this could corrupt the block ack window
and lock up the aggregation session. Fix this by delaying the new session
until the old one has been cleaned up.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There's no reason to keep pointers to pending tx buffers around, if they're
only used to keep track of which frames are still pending. Use a bitfield
instead.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
typo - while looking for specific bits we should do a bitwise-AND instead of logical-AND.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
copy the rx_status directly to skb->cb (control buffer) instead of copying
it to a local struct and then copying it again (for each rx packet)
Signed-off-by: Eliad Peller <eliad@wizery.com>
Acked-by: Luciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is a obvious bug, skb_queue_walk does not
work if the iterator gets removed from the queue.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver has a set of different initvals for 20 MHz
vs dynamic HT2040 operation. Because we can't change
some of the registers "in-flight", the driver needs to
perform a warm reset.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Don't mark the device as completely dead just yet.
If all goes to plan and carl9170_reboot succeeds
then we can skip the expensive userspace-driven
reinitialization anyway.
And if it doesn't and carl9170_reboot fails,
then carl9170_usb_cancel_urbs will do the
necessary steps.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
