Arch code can define ARCH_DISCARD_MEMBLOCK in asm/memblock.h,
which in turns causes memblock code and data to go respectively
into the .init and .initdata sections. This will be used by the
x86 architecture.
If ARCH_DISCARD_MEMBLOCK is defined, the debugfs files to inspect
the memblock arrays after boot are not created.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
And ensure we don't hand out 0 as a valid allocation. We put the
low limit at PAGE_SIZE arbitrarily.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
will used by x86 memblock_x86_find_in_range_node and nobootmem replacement
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Print out the location info in addition to which array is being
resized. Also use memblocK_dbg() to put that under control of
the memblock_debug flag.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This exposes memblock_debug and associated memblock_dbg() macro,
along with memblock_can_resize so that x86 can use these when
ported to use memblock
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
memblock_alloc_nid() used to fallback to allocating anywhere by using
memblock_alloc() as a fallback.
However, some of my previous patches limit memblock_alloc() to the region
covered by MEMBLOCK_ALLOC_ACCESSIBLE which is not quite what we want
for memblock_alloc_try_nid().
So we fix it by explicitely using MEMBLOCK_ALLOC_ANYWHERE.
Not that so far only sparc uses memblock_alloc_nid() and it hasn't been updated
to clamp the accessible zone yet. Thus the temporary "breakage" should have
no effect.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The former is now strict, it will fail if it cannot honor the allocation
within the node, while the later implements the previous semantic which
falls back to allocating anywhere.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
We now provide a default (weak) implementation of memblock_nid_range()
which uses the early_pfn_map[] if CONFIG_ARCH_POPULATES_NODE_MAP
is set. Sparc still needs to use its own method due to the way
the pages can be scattered between nodes.
This implementation is inefficient due to our main algorithm and
callback construct wanting to work on an ascending addresses bases
while early_pfn_map[] would rather work with nid's (it's unsorted
at that stage). But it should work and we can look into improving
it subsequently, possibly using arch compile options to chose a
different algorithm alltogether.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To constraint the search of a region between two boundaries,
which will be used by the new NUMA aware allocator among others.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some archs such as ARM want to avoid coalescing accross things such
as the lowmem/highmem boundary or similar. This provides the option
to control it via an arch callback for which a weak default is provided
which always allows coalescing.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
When one of the array gets full, we resize it. After much thinking and
a few iterations of that code, I went back to on-demand resizing using
the (new) internal memblock_find_base() function, which is pretty much what
Yinghai initially proposed, though there some differences in the details.
To work this relies on the default alloc limit being set sensibly by
the architecture.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Some shuffling is needed for doing array resize so we may as well
put some sense into the ordering of the functions in the whole memblock.c
file. No code change. Added some comments.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This will be used by the array resize code and might prove useful
to some arch code as well at which point it can be made non-static.
Also add comment as to why aligning size is important
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2. Fix loss of size alignment
v3. Fix result code
This function will be used to locate a free area to put the new memblock
arrays when attempting to resize them. memblock_alloc_region() is gone,
the two callsites now call memblock_add_region().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
---
v2. Fix membase_alloc_nid_region() conversion
Since we allocate one more than needed, why not do a bit of sanity checking
here to ensure we don't walk past the end of the array ?
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This is in preparation for having resizable arrays.
Note that we still allocate one more than needed, this is unchanged from
the previous implementation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Right now, both the "memory" and "reserved" memblock_type structures have
a "size" member. It represents the calculated memory size in the former
case and is unused in the latter.
This moves it out to the main memblock structure instead
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Let's not waste space and cycles on archs that don't support >32-bit
physical address space.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
The RMA (RMO is a misnomer) is a concept specific to ppc64 (in fact
server ppc64 though I hijack it on embedded ppc64 for similar purposes)
and represents the area of memory that can be accessed in real mode
(aka with MMU off), or on embedded, from the exception vectors (which
is bolted in the TLB) which pretty much boils down to the same thing.
We take that out of the generic MEMBLOCK data structure and move it into
arch/powerpc where it belongs, renaming it to "RMA" while at it.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
This introduce memblock.current_limit which is used to limit allocations
from memblock_alloc() or memblock_alloc_base(..., MEMBLOCK_ALLOC_ACCESSIBLE).
The old MEMBLOCK_ALLOC_ANYWHERE changes value from 0 to ~(u64)0 and can still
be used with memblock_alloc_base() to allocate really anywhere.
It is -no-longer- cropped to MEMBLOCK_REAL_LIMIT which disappears.
Note to archs: I'm leaving the default limit to MEMBLOCK_ALLOC_ANYWHERE. I
strongly recommend that you ensure that you set an appropriate limit
during boot in order to guarantee that an memblock_alloc() at any time
results in something that is accessible with a simple __va().
The reason is that a subsequent patch will introduce the ability for
the array to resize itself by reallocating itself. The MEMBLOCK core will
honor the current limit when performing those allocations.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
To make it fast, we steal ARM's binary search for memblock_is_memory()
and we use that to also the replace existing implementation of
memblock_is_reserved().
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
All callers expect a boolean result which is true if the region
overlaps a reserved region. However, the implementation actually
returns -1 if there is no overlap, and a region index (0 based)
if there is.
Make it behave as callers (and common sense) expect.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Debian's ia64 autobuilders have been seeing kernel freeze or reboot
when running the gdb testsuite (Debian bug 588574): dannf bisected to
2.6.32 62eede62da "mm: ZERO_PAGE without
PTE_SPECIAL"; and reproduced it with gdb's gcore on a simple target.
I'd missed updating the gate_vma handling in __get_user_pages(): that
happens to use vm_normal_page() (nowadays failing on the zero page),
yet reported success even when it failed to get a page - boom when
access_process_vm() tried to copy that to its intermediate buffer.
Fix this, resisting cleanups: in particular, leave it for now reporting
success when not asked to get any pages - very probably safe to change,
but let's not risk it without testing exposure.
Why did ia64 crash with 16kB pages, but succeed with 64kB pages?
Because setup_gate() pads each 64kB of its gate area with zero pages.
Reported-by: Andreas Barth <aba@not.so.argh.org>
Bisected-by: dann frazier <dannf@debian.org>
Signed-off-by: Hugh Dickins <hughd@google.com>
Tested-by: dann frazier <dannf@dannf.org>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We need lock_page_nosync() here because we have no reference to the
mapping when taking the page lock.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Reviewed-by: Johannes Weiner <hannes@cmpxchg.org>
Cc: Mel Gorman <mel@csn.ul.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
* 'kmemleak' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-2.6-cm:
kmemleak: Add support for NO_BOOTMEM configurations
kmemleak: Annotate false positive in init_section_page_cgroup()
With commits 08677214 and 59be5a8e, alloc_bootmem()/free_bootmem() and
friends use the early_res functions for memory management when
NO_BOOTMEM is enabled. This patch adds the kmemleak calls in the
corresponding code paths for bootmem allocations.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Acked-by: Yinghai Lu <yinghai@kernel.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: stable@kernel.org
The pointer to the page_cgroup table allocated in
init_section_page_cgroup() is stored in section->page_cgroup as (base -
pfn). Since this value does not point to the beginning or inside the
allocated memory block, kmemleak reports a false positive.
This was reported in bugzilla.kernel.org as #16297.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Reported-by: Adrien Dessemond <adrien.dessemond@gmail.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
writeback: simplify the write back thread queue
writeback: split writeback_inodes_wb
writeback: remove writeback_inodes_wbc
fs-writeback: fix kernel-doc warnings
splice: check f_mode for seekable file
splice: direct_splice_actor() should not use pos in sd
First remove items from work_list as soon as we start working on them. This
means we don't have to track any pending or visited state and can get
rid of all the RCU magic freeing the work items - we can simply free
them once the operation has finished. Second use a real completion for
tracking synchronous requests - if the caller sets the completion pointer
we complete it, otherwise use it as a boolean indicator that we can free
the work item directly. Third unify struct wb_writeback_args and struct
bdi_work into a single data structure, wb_writeback_work. Previous we
set all parameters into a struct wb_writeback_args, copied it into
struct bdi_work, copied it again on the stack to use it there. Instead
of just allocate one structure dynamically or on the stack and use it
all the way through the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This was just an odd wrapper around writeback_inodes_wb. Removing this
also allows to get rid of the bdi member of struct writeback_control
which was rather out of place there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
My patch to "Factor out duplicate put/frees in mpol_shared_policy_init()
to a common return path"; and Dan Carpenter's fix thereto both left a
dangling reference to the incoming tmpfs superblock mempolicy structure.
A similar leak was introduced earlier when the nodemask was moved offstack
to the scratch area despite the note in the comment block regarding the
incoming ref.
Move the remaining 'put of the incoming "mpol" to the common exit path to
drop the reference.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Dan Carpenter <error27@gmail.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
OOM-waitqueue should be waken up when oom_disable is canceled. This is a
fix for 3c11ecf448 ("memcg: oom kill disable and oom status").
How to test:
Create a cgroup A...
1. set memory.limit and memory.memsw.limit to be small value
2. echo 1 > /cgroup/A/memory.oom_control, this disables oom-kill.
3. run a program which must cause OOM.
A program executed in 3 will sleep by oom_waiqueue in memcg. Then, how to
wake it up is problem.
1. echo 0 > /cgroup/A/memory.oom_control (enable OOM-killer)
2. echo big mem > /cgroup/A/memory.memsw.limit_in_bytes(allow more swap)
etc..
Without the patch, a task in slept can not be waken up.
Signed-off-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Acked-by: Daisuke Nishimura <nishimura@mxp.nes.nec.co.jp>
Cc: Balbir Singh <balbir@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Don't count_vm_events for discard bio in submit_bio.
cfq: fix recursive call in cfq_blkiocg_update_completion_stats()
cfq-iosched: Fixed boot warning with BLK_CGROUP=y and CFQ_GROUP_IOSCHED=n
cfq: Don't allow queue merges for queues that have no process references
block: fix DISCARD_BARRIER requests
cciss: set SCSI max cmd len to 16, as default is wrong
cpqarray: fix two more wrong section type
cpqarray: fix wrong __init type on pci probe function
drbd: Fixed a race between disk-attach and unexpected state changes
writeback: fix pin_sb_for_writeback
writeback: add missing requeue_io in writeback_inodes_wb
writeback: simplify and split bdi_start_writeback
writeback: simplify wakeup_flusher_threads
writeback: fix writeback_inodes_wb from writeback_inodes_sb
writeback: enforce s_umount locking in writeback_inodes_sb
writeback: queue work on stack in writeback_inodes_sb
writeback: fix writeback completion notifications
per_cpu_ptr_to_phys() determines whether the passed in @addr belongs
to the first_chunk or not by just matching the address against the
address range of the base unit (unit0, used by cpu0). When an adress
from another cpu was passed in, it will always determine that the
address doesn't belong to the first chunk even when it does. This
makes the function return a bogus physical address which may lead to
crash.
This problem was discovered by Cliff Wickman while investigating a
crash during kdump on a SGI UV system.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Cliff Wickman <cpw@sgi.com>
Tested-by: Cliff Wickman <cpw@sgi.com>
Cc: stable@kernel.org
Fix the following two trivial bugs in pcpu_build_alloc_info()
* we should memset group_cnt to 0 by size of group_cnt, not size of
group_map (both are of the same size, so the bug isn't dangerous)
* we can delete useless variable group_cnt_max.
Signed-off-by: Pavel V. Panteleev <pp_84@mail.ru>
Signed-off-by: Tejun Heo <tj@kernel.org>
bdi_start_writeback now never gets a superblock passed, so we can just remove
that case. And to further untangle the code and flatten the call stack
split it into two trivial helpers for it's two callers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
sync can currently take a really long time if a concurrent writer is
extending a file. The problem is that the dirty pages on the address
space grow in the same direction as write_cache_pages scans, so if
the writer keeps ahead of writeback, the writeback will not
terminate until the writer stops adding dirty pages.
For a data integrity sync, we only need to write the pages dirty at
the time we start the writeback, so we can stop scanning once we get
to the page that was at the end of the file at the time the scan
started.
This will prevent operations like copying a large file preventing
sync from completing as it will not write back pages that were
dirtied after the sync was started. This does not impact the
existing integrity guarantees, as any dirty page (old or new)
within the EOF range at the start of the scan will still be
captured.
This patch will not prevent sync from blocking on large writes into
holes. That requires more complex intervention while this patch only
addresses the common append-case of this sync holdoff.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
If a filesystem writes more than one page in ->writepage, write_cache_pages
fails to notice this and continues to attempt writeback when wbc->nr_to_write
has gone negative - this trace was captured from XFS:
wbc_writeback_start: towrt=1024
wbc_writepage: towrt=1024
wbc_writepage: towrt=0
wbc_writepage: towrt=-1
wbc_writepage: towrt=-5
wbc_writepage: towrt=-21
wbc_writepage: towrt=-85
This has adverse effects on filesystem writeback behaviour. write_cache_pages()
needs to terminate after a certain number of pages are written, not after a
certain number of calls to ->writepage are made. This is a regression
introduced by 17bc6c30cf ("vfs: Add
no_nrwrite_index_update writeback control flag"), but cannot be reverted
directly due to subsequent bug fixes that have gone in on top of it.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
Minix: Clean up left over label
fix truncate inode time modification breakage
fix setattr error handling in sysfs, configfs
fcntl: return -EFAULT if copy_to_user fails
wrong type for 'magic' argument in simple_fill_super()
fix the deadlock in qib_fs
mqueue doesn't need make_bad_inode()
