Commit Graph

12 Commits

Author SHA1 Message Date
Steve Wise
4ab928f692 RDMA/cxgb3: Fixes for zero STag
Handling the zero STag in receive work request requires some extra
logic in the driver:

 - Only set the QP_PRIV bit for kernel mode QPs.

- Add a zero STag build function for recv wrs. The uP needs a PBL
  allocated and passed down in the recv WR so it can construct a HW
  PBL for the zero STag S/G entries.  Note: we need to place a few
  restrictions on zero STag usage because of this:

  1) all SGEs in a recv WR must either be zero STag or not.  No mixing.

  2) an individual SGE length cannot exceed 128MB for a zero-stag SGE.
     This should be OK since it's not really practical to allocate
     such a large chunk of pinned contiguous DMA mapped memory.

- Add an optimized non-zero-STag recv wr format for kernel users.
  This is needed to optimize both zero and non-zero STag cracking in
  the recv path for kernel users.

 - Remove the iwch_ prefix from the static build functions.

 - Bump required FW version.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
2008-07-14 23:48:53 -07:00
Steve Wise
f8b0dfd152 RDMA/cxgb3: Support peer-2-peer connection setup
Open MPI, Intel MPI and other applications don't respect the iWARP
requirement that the client (active) side of the connection send the
first RDMA message.  This class of application connection setup is
called peer-to-peer.  Typically once the connection is setup, _both_
sides want to send data.

This patch enables supporting peer-to-peer over the chelsio RNIC by
enforcing this iWARP requirement in the driver itself as part of RDMA
connection setup.

Connection setup is extended, when the peer2peer module option is 1,
such that the MPA initiator will send a 0B Read (the RTR) just after
connection setup.  The MPA responder will suspend SQ processing until
the RTR message is received and reply-to.

In the longer term, this will be handled in a standardized way by
enhancing the MPA negotiation so peers can indicate whether they
want/need the RTR and what type of RTR (0B read, 0B write, or 0B send)
should be sent.  This will be done by standardizing a few bits of the
private data in order to negotiate all this.  However this patch
enables peer-to-peer applications now and allows most of the required
firmware and driver changes to be done and tested now.

Design:

 - Add a module option, peer2peer, to enable this mode.

 - New firmware support for peer-to-peer mode:

	- a new bit in the rdma_init WR to tell it to do peer-2-peer
	  and what form of RTR message to send or expect.

	- process _all_ preposted recvs before moving the connection
	  into rdma mode.

	- passive side: defer completing the rdma_init WR until all
	  pre-posted recvs are processed.  Suspend SQ processing until
	  the RTR is received.

	- active side: expect and process the 0B read WR on offload TX
	  queue. Defer completing the rdma_init WR until all
	  pre-posted recvs are processed.  Suspend SQ processing until
	  the 0B read WR is processed from the offload TX queue.

 - If peer2peer is set, driver posts 0B read request on offload TX
   queue just after posting the rdma_init WR to the offload TX queue.

 - Add CQ poll logic to ignore unsolicitied read responses.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2008-04-29 13:46:52 -07:00
Divy Le Ray
273fa9042c cxgb3 - FW upgrade
Bump up FW version to 5.0.
Do not downgrade FW within the same major version range.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2008-01-28 15:04:09 -08:00
Divy Le Ray
a5a3b4601b cxgb3 - Firmware update
Update firmware version.
Allow the driver to be up and running with older FW image

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-10-10 16:51:03 -07:00
Steve Wise
de3d353072 RDMA/cxgb3: Streaming -> RDMA mode transition fixes
Due to a HW issue, our current scheme to transition the connection from
streaming to rdma mode is broken on the passive side.  The firmware
and driver now support a new transition scheme for the passive side:

 - driver posts rdma_init_wr (now including the initial receive seqno)
 - driver posts last streaming message via TX_DATA message (MPA start
   response)
 - uP atomically sends the last streaming message and transitions the
   tcb to rdma mode.
 - driver waits for wr_ack indicating the last streaming message was ACKed.

NOTE: This change also bumps the required firmware version to 4.3.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-07-09 20:12:26 -07:00
Divy Le Ray
8a9fab22cf cxgb3 - Firmware update
Update FW to 4.1.
Proceed to subsequent HW tuning to improve RDMA perfs..

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-07-08 22:16:39 -04:00
Steve Wise
aff9e39d97 RDMA/cxgb3: Support for new abort logic
The HW now posts 2 ABORT_RPL and/or PEER_ABORT_REQ messages.  We need
to handle them by silenty dropping the 1st but mark that we're ready
for the final message.  This plugs some close races between the uP and
HW.  Also update the minimum required firmware version.

Signed-off-by: Steve Wise <swise@opengridcomputing.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
2007-05-06 21:18:08 -07:00
Divy Le Ray
7f672cf5b2 cxgb3 - Firwmare update
Introduce FW micro version.
Bump up FW version to 3.3.0

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-04-03 22:31:09 -04:00
Divy Le Ray
d518725fa6 cxgb3 - Tag driver version
This patch adds a "-ko" tag to the driver version.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-03-02 19:55:07 -05:00
Divy Le Ray
75d8626fdd cxgb3 - FW version update
Update FW version to 3.2

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-27 04:27:12 -05:00
Divy Le Ray
1d68e93d65 cxgb3 - Add dual licensing
Dual licensing, needed for OFED 1.2

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:51 -05:00
Divy Le Ray
4d22de3e6c Add support for the latest 1G/10G Chelsio adapter, T3.
This driver is required by the Chelsio T3 RDMA driver posted by
Steve Wise.

Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-02-05 16:58:46 -05:00