Commit Graph

61 Commits

Author SHA1 Message Date
Felipe Balbi
72246da40f usb: Introduce DesignWare USB3 DRD Driver
The DesignWare USB3 is a highly
configurable IP Core which can be
instantiated as Dual-Role Device (DRD),
Peripheral Only and Host Only (XHCI)
configurations.

Several other parameters can be configured
like amount of FIFO space, amount of TX and
RX endpoints, amount of Host Interrupters,
etc.

The current driver has been validated with
a virtual model of version 1.73a of that core
and with an FPGA burned with version 1.83a
of the DRD core. We have support for PCIe
bus, which is used on FPGA prototyping, and
for the OMAP5, more adaptation (or glue)
layers can be easily added and the driver
is half prepared to handle any possible
configuration the HW engineer has chosen
considering we have the information on
one of the GHWPARAMS registers to do
runtime checking of certain features.

More runtime checks can, and should, be added
in order to make this driver even more flexible
with regards to number of endpoints, FIFO sizes,
transfer types, etc.

While this supports only the device side, for
now, we will add support for Host side (xHCI -
see the updated series Sebastian has sent [1])
and OTG after we have it all stabilized.

[1] http://marc.info/?l=linux-usb&m=131341992020339&w=2

Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 16:03:11 -07:00
Tanmay Upadhyay
3abd7f68b2 USB: pxa168: Add onchip USB host controller support
- Add EHCI Host controller driver
- Add wrapper that creates resources for host controller driver

v2 - Call clk_put() after clk_disable() in probe function

Signed-off-by: Tanmay Upadhyay <tanmay.upadhyay@einfochips.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-08-22 15:38:30 -07:00
Jan Andersson
9be0392989 USB: EHCI: Add bus glue for GRLIB GRUSBHC controller
This patch adds support for the GRLIB GRUSBHC EHCI controller from
Aeroflex Gaisler. The controller is typically found on LEON/GRLIB
SoCs.

Tested on GR-LEON4-ITX with with little endian interface and on
LEON3 system on GR-PCI-XC5V development board for big endian
controller.

Signed-off-by: Jan Andersson <jan@gaisler.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-05-03 11:43:48 -07:00
Greg Kroah-Hartman
50ee9339c7 Merge 2.6.39-rc4 into usb-next
This is needed to help resolve some xhci issues and other minor
differences.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-19 05:50:38 -07:00
Joonyoung Shim
1bcc5aa87f USB: Add initial S5P EHCI driver
This patch adds host USB high speed driver for samsung S5P series. This
is initial driver and we need additional implementation to support some
functions like power management.

Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-13 16:50:52 -07:00
Kuninori Morimoto
f1407d5c66 usb: renesas_usbhs: Add Renesas USBHS common code
Renesas SuperH has USBHS IP which can switch Host / Function.
This driver is designed so that Host / Function may dynamically change.
This patch add usb/renesas_usbhs and common code for SuperH USBHS.

Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-13 16:07:07 -07:00
Michal Simek
0291303d37 usb: Fix Kconfig unmet dependencies for Microblaze EHCI
Disable USB_ARCH_HAS_EHCI in arch Kconfig and enable it in usb Kconfig

Warning log:
warning: (MICROBLAZE) selects USB_ARCH_HAS_EHCI which has unmet
direct dependencies (USB_SUPPORT)

Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2011-04-13 15:43:59 -07:00
Russell King
82e6923e18 ARM: lh7a40x: remove unmaintained platform support
lh7a40x has only been receiving updates for updates to generic code.
The last involvement from the maintainer according to the git logs was
in 2006.  As such, it is a maintainence burden with no benefit.

This gets rid of two defconfigs.

Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2011-01-24 19:05:19 +00:00
Linus Torvalds
3e5b08cbbf Merge branch 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* 'usb-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (144 commits)
  USB: add support for Dream Cheeky DL100B Webmail Notifier (1d34:0004)
  USB: serial: ftdi_sio: add support for TIOCSERGETLSR
  USB: ehci-mxc: Setup portsc register prior to accessing OTG viewport
  USB: atmel_usba_udc: fix freeing irq in usba_udc_remove()
  usb: ehci-omap: fix tll channel enable mask
  usb: ohci-omap3: fix trivial typo
  USB: gadget: ci13xxx: don't assume that PAGE_SIZE is 4096
  USB: gadget: ci13xxx: fix complete() callback for no_interrupt rq's
  USB: gadget: update ci13xxx to work with g_ether
  USB: gadgets: ci13xxx: fix probing of compiled-in gadget drivers
  Revert "USB: musb: pm: don't rely fully on clock support"
  Revert "USB: musb: blackfin: pm: make it work"
  USB: uas: Use GFP_NOIO instead of GFP_KERNEL in I/O submission path
  USB: uas: Ensure we only bind to a UAS interface
  USB: uas: Rename sense pipe and sense urb to status pipe and status urb
  USB: uas: Use kzalloc instead of kmalloc
  USB: uas: Fix up the Sense IU
  usb: musb: core: kill unneeded #include's
  DA8xx: assign name to MUSB IRQ resource
  usb: gadget: g_ncm added
  ...

Manually fix up trivial conflicts in USB Kconfig changes in:
	arch/arm/mach-omap2/Kconfig
	arch/sh/Kconfig
	drivers/usb/Kconfig
	drivers/usb/host/ehci-hcd.c
and annoying chip clock data conflicts in:
	arch/arm/mach-omap2/clock3xxx_data.c
	arch/arm/mach-omap2/clock44xx_data.c
2011-01-07 13:16:28 -08:00
Pavankumar Kondeti
b0848aea10 USB: EHCI: Add MSM Host Controller driver
This patch adds support for EHCI compliant HSUSB Host controller found
on MSM chips.  The root hub has a single port and TT is built into it.
This driver depends on OTG driver for PHY initialization, clock
management and powering up VBUS.

Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-12-10 14:23:32 -08:00
Greg Kroah-Hartman
fe4bfb30fe Merge branch 'sh/ehci' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6 into work
* 'sh/ehci' of master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Convert to USB_ARCH_HAS_OHCI/EHCI selects.
  usb: ehci-sh: Add missing ehci helpers.
  usb: ehci-sh: Fix up fault in shutdown path.
  sh: Add EHCI support for SH7786.
  usb: ehci-hcd: Add support for SuperH EHCI.
  usb: ohci-sh: Set IRQ as shared.
2010-12-03 12:12:29 -08:00
Paul Mundt
e3e9887ee9 sh: Convert to USB_ARCH_HAS_OHCI/EHCI selects.
This switches over to selects for the subtypes to enable OHCI/EHCI
support explicitly rather than littering the usb Kconfig with subtype
dependencies.

Suggested-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-12-01 15:58:58 +09:00
Mac Lin
760efe6910 USB: cns3xxx: Add EHCI and OHCI bus glue for cns3xxx SOCs
The CNS3XXX SOC has include USB EHCI and OHCI compatible controllers.
This patch adds the necessary glue logic to allow ehci-hcd and ohci-hcd
drivers to work on CNS3XXX

The EHCI and OHCI controllers share a common clock control and reset
bit, therefore additional check for the timming of enabling and disabling
is required. The USB bit of PLL Power Down Control is also shared by OTG,
24MHzUART clock, Crypto clock, PCIe reference clock, and Clock Scale
Generator. Therefore we only ensure it is enabled, while not disabling it.

Signed-off-by: Mac Lin <mkl0301@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
2010-11-29 18:32:47 +03:00
Deepak Sikri
c8c38de9d8 USB host: Adding USB ehci & ohci support for spear platform
This patch adds support for ehci and ohci controller in the SPEAr platform.

Changes since V2:
added clear_tt_buffer_complete in ehci_spear_hc_driver

Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-11-16 13:53:29 -08:00
Alexey Charkov
ad78acafee usb: Add support for VIA VT8500 and compatibles in EHCI HCD
VIA and WonderMedia Systems-on-Chip feature a standard EHCI host
controller. This adds necessary glue to use the standard driver
with these systems.

Signed-off-by: Alexey Charkov <alchark@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-11-11 06:24:54 -08:00
Paul Mundt
63c8455222 usb: ehci-hcd: Add support for SuperH EHCI.
This adds a trivial stub for supporting EHCI mode of the on-chip
SH USB host controllers.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2010-11-01 17:03:27 -04:00
Anatolij Gustschin
230f7ede6c USB: add USB EHCI support for MPC5121 SoC
Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.

The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-10-22 10:21:58 -07:00
Lars-Peter Clausen
2249071b3e USB: Add JZ4740 OHCI support
Add OHCI glue code for JZ4740 SoCs OHCI module.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: linux-usb@vger.kernel.org
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: linux-mips@linux-mips.org
Cc: linux-kernel@vger.kernel.org
Patchwork: https://patchwork.linux-mips.org/patch/1411/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-08-05 13:26:19 +01:00
Manuel Lauss
42a4f17dc3 MIPS: Alchemy: remove SOC_AU1X00 in favor of MIPS_ALCHEMY
Remove the CONFIG_SOC_AU1X00 Kconfig symbol since its job can also be done
by MACH_ALCHEMY, now renamed to MIPS_ALCHEMY.

Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1461/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
2010-08-05 13:26:06 +01:00
Linus Torvalds
7f5b09c15a Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6: (220 commits)
  USB: backlight, appledisplay: fix incomplete registration failure handling
  USB: pl2303: remove unnecessary reset of usb_device in urbs
  USB: ftdi_sio: remove obsolete check in unthrottle
  USB: ftdi_sio: remove unused tx_bytes counter
  USB: qcaux: driver for auxiliary serial ports on Qualcomm devices
  USB: pl2303: initial TIOCGSERIAL support
  USB: option: add Longcheer/Longsung vendor ID
  USB: fix I2C API usage in ohci-pnx4008.
  USB: usbmon: mask seconds properly in text API
  USB: sisusbvga: no unnecessary GFP_ATOMIC
  USB: storage: onetouch: unnecessary GFP_ATOMIC
  USB: serial: ftdi: add CONTEC vendor and product id
  USB: remove references to port->port.count from the serial drivers
  USB: tty: Prune uses of tty_request_room in the USB layer
  USB: tty: Add a function to insert a string of characters with the same flag
  USB: don't read past config->interface[] if usb_control_msg() fails in usb_reset_configuration()
  USB: tty: kill request_room for USB ACM class
  USB: tty: sort out the request_room handling for whiteheat
  USB: storage: fix misplaced parenthesis
  USB: vstusb.c: removal of driver for Vernier Software & Technology, Inc., devices and spectrometers
  ...
2010-03-03 08:48:58 -08:00
Sergei Shtylyov
efe7daf223 USB: OHCI: DA8xx/OMAP-L1x glue layer
Texas Instruments DA8xx/OMAP-L1x OHCI glue layer.

This OHCI implementation is not without quirks: there's only one physical port
despite the root hub reporting two; the port's power control and over-current
status bits are not connected to any pins, however, at least on the DA830 EVM
board, those signals are connected via GPIO, thus the provision was made for
overriding the OHCI port power and over-current bits at the board level...

Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:55:06 -08:00
Michael Hennerich
ca0e9485af USB: host: SL811: allow the hcd on Blackfin systems
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2010-03-02 14:53:27 -08:00
Tony Lindgren
a8eb7ca0cb omap3: Replace ARCH_OMAP34XX with ARCH_OMAP3
Replace ARCH_OMAP34XX with ARCH_OMAP3

Signed-off-by: Tony Lindgren <tony@atomide.com>
2010-02-15 09:27:02 -08:00
Anand Gadiyar
796c8c7880 USB: ehci: Allow EHCI to be built on OMAP3
usb: ehci: Allow EHCI to be built on OMAP3

OMAP3 chips have a built-in EHCI controller.
The recently introduced omap ehci-hcd driver missed
out on selecting USB_ARCH_HAS_EHCI in Kconfig.

Without this, the driver cannot be built.

Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Vikram Pandita <vikram.pandita@ti.com>
Cc: Ajay Kumar Gupta <ajay.gupta@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 11:55:20 -08:00
Daniel Mack
7e8d5cd93f USB: Add EHCI support for MX27 and MX31 based boards
The Freescale MX27 and MX31 SoCs have a EHCI controller onboard.
The controller is capable of USB on the go. This patch adds
a driver to support all three of them.

Users have to pass details about serial interface configuration in the
platform data.

The USB OTG core used here is the ARC core, so the driver should
be renamed and probably be merged with ehci-fsl.c eventually.

Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-12-11 11:55:18 -08:00
Linus Torvalds
a6b49cb210 Merge branch 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze
* 'for-linus' of git://git.monstr.eu/linux-2.6-microblaze: (24 commits)
  microblaze: Disable heartbeat/enable emaclite in defconfigs
  microblaze: Support simpleImage.dts make target
  microblaze: Fix _start symbol to physical address
  microblaze: Use LOAD_OFFSET macro to get correct LMA for all sections
  microblaze: Create the LOAD_OFFSET macro used to compute VMA vs LMA offsets
  microblaze: Copy ppc asm-compat.h for clean handling of constants in asm and C
  microblaze: Actually show KiB rather than pages in "Freeing initrd memory:"
  microblaze: Support ptrace syscall tracing.
  microblaze: Updated CPU version and FPGA family codes in PVR
  microblaze: Generate correct signal and siginfo for integer div-by-zero
  microblaze: Don't be noisy when userspace causes hardware exceptions
  microblaze: Remove ipc.h file which points to non-existing asm-generic file
  microblaze: Clear sticky FSR register after generating exception signals
  microblaze: Ensure CPU usermode is set on new userspace processes
  microblaze: Use correct kbuild variable KBUILD_CFLAGS
  microblaze: Save and restore msr in hw exception
  microblaze: Add architectural support for USB EHCI host controllers
  microblaze: Implement include/asm/syscall.h.
  microblaze: Improve checking mechanism for MSR instruction
  microblaze: Add checking mechanism for MSR instruction
  ...
2009-09-24 09:01:44 -07:00
Nicolas Ferre
501c9c0802 USB: at91: Add USB EHCI driver for at91sam9g45 series
Add host USB High speed driver for at91sam9g45 series.
The host driver is an EHCI with its companion OHCI. EHCI is
handled by the new ehci-atmel.c whereas the OHCI is always
handled by ohci-at91.c.

Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
2009-09-23 06:46:30 -07:00
Wan ZongShun
586dfc8caf USB: Add nuvoton Ehci driver for w90p910 platform
Add ehci support for w90p910 platform.

Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-09-23 06:46:20 -07:00
Julie Zhu
afc26cb39e microblaze: Add architectural support for USB EHCI host controllers
Add architectural support for USB EHCI host controllers. It has been tested
using the USB EHCI host controller from Xilinx Inc., using both High Speed
devices and Full Speed devices.

Signed-off-by: Julie Zhu <julie.zhu@xilinx.com>
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-09-22 08:50:14 +02:00
Clemens Ladisch
a853a3d4eb usb: return device strings in UTF-8
Change the encoding of strings returned by usb_string() from ISO 8859-1
to UTF-8.

Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-06-15 21:44:43 -07:00
Michal Simek
6fa612b56c microblaze: Kconfig: Enable drivers for Microblaze
Signed-off-by: Michal Simek <monstr@monstr.eu>
2009-05-21 15:56:04 +02:00
Kuninori Morimoto
4c3f450ba4 sh: Add OHCI USB support for SH7786
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
2009-03-16 19:40:34 +09:00
David Brownell
b8da8677d4 USB: move isp1301_omap to drivers/usb/otg
This moves the isp1301-omap driver from the drivers/i2c/chips
directory (which will be shrinking) into a new drivers/usb/otg
directory (which will grow, with more drivers and utilities).

Note that OTG infrastructure needs to be initialized before
either host or peripheral side USB support, and may be needed
before for pure host or pure peripheral configurations.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2009-01-07 10:00:02 -08:00
Linus Torvalds
a27028349c Merge git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb-2.6:
  USB: don't rebind drivers after failed resume or reset
  USB: fix memory leak in cdc-acm
  USB: Unusual dev for Mio moov 330 gps
  USB: cdc-wdm: make module autoload work
  USB: Fix unneeded endpoint check in pxa27x_udc
  usb/gadget: fix kernel-doc warning
  USB: Speedtouch: add pre_reset and post_reset routines
  USB: usbtest.c: length, sglen and vary are unsigned, so cannot be negative
  USB: support Huawei data card product IDs
  USB: add ZTE MF626 USB GSM modem entry
  USB: storage: Avoid I/O errors when issuing SCSI ioctls to JMicron USB/ATA bridge
  USB: Fix debugfs_create_file's error checking method for usb/gadget/s3c2410_udc
  USB: ohci: add support for tmio-ohci cell
2008-10-23 10:09:50 -07:00
Dmitry Baryshkov
78c73414f4 USB: ohci: add support for tmio-ohci cell
Some Toshiba Mobile I/O chips have OHCI controller built in.
E.g. the tc6393xb chip found in several Toshiba e-Series PDAs
and in Sharp Zaurus SL-6000 PDA. This adds platform glue
to support OHCI function of the chip.

Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Ian Molton <spyro@f2s.com>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-10-22 10:05:27 -07:00
Greg Kroah-Hartman
470cc41503 wusb: add the Wireless USB core (build-system)
Add the WUSB build system (Kconfig and Kbuild) files.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David Vrabel <david.vrabel@csr.com>
2008-09-17 16:54:30 +01:00
Felipe Balbi
550a7375fe USB: Add MUSB and TUSB support
This patch adds support for MUSB and TUSB controllers
integrated into omap2430 and davinci. It also adds support
for external tusb6010 controller.

Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13 17:33:00 -07:00
Simon Arlott
3bea302d6a USB: Move usb/mon/ up to misc options in Kconfig
This makes "USB Monitor" appear under "Miscellaneous USB options"
section instead of in the middle of device specific drivers in the
"USB Imaging devices" section.

Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-08-13 17:32:50 -07:00
Yoshihiro Shimoda
828d55c58c USB: add support for SuperH OHCI
add support for SuperH OHCI.

supported CPU are:
 - SH7720
 - SH7721
 - SH7763

Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Acked-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:03 -08:00
Vladimir Barinov
91bc4d31e8 USB: add ehci-ixp bus glue
EHCI Glue driver for Intel IXP4XX EHCI USB controller

Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2008-02-01 14:35:02 -08:00
eric miao
e77ec1898f [ARM] USB: update to allow pxa27x ohci driver to support pxa3xx
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-01-26 15:07:53 +00:00
Paul Mundt
a3b53514bd usb: Enable hcd support on SH unconditionally.
Previous boards were likely seeing USB_ARCH_HAS_HCD selected by way
of PCMCIA or PCI, though none of those are required for hcd support
on SH. Enable support unconditionally.

Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-08-22 14:27:45 -07:00
Jan Engelhardt
06bfb7eb15 Add some help texts to recently-introduced kconfig items
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de> (edited MACINTOSH_DRIVERS per Geert Uytterhoeven's remark)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-08-18 09:52:50 -07:00
Al Viro
0ab7a252a5 no USB on M32R
Won't build due to lack of dma-mapping.

Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-17 11:01:07 -07:00
Linus Torvalds
773208946a Revert "USB: fix gregkh-usb-usb-use-menuconfig-objects"
This reverts commit acb11c8b80.

It was broken.  We most certainly *do* want the default to be the old
behaviour (and the common case!), instead of breaking everybodys
configuration and making 99% of all people have to override the default.

What were you guys thinking?

Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-07-12 17:06:50 -07:00
Jan Engelhardt
acb11c8b80 USB: fix gregkh-usb-usb-use-menuconfig-objects
Generally, Jens Axboe was against 'default y', so I'll have some patches to
remove it.

Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:40 -07:00
David Brownell
648dcfc805 USB: usb host side can be configured given PCMCIA
Platforms with PCMCIA support can implement host-side USB with "sl811_cs",
so make sure this menu shows up on platforms with PCMCIA.

Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:34:31 -07:00
Jan Engelhardt
04d06ad0f1 USB: Use menuconfig objects
Make a "menuconfig" out of the Kconfig objects "menu, ..., endmenu", so that
the user can disable all the options in that menu at once instead of having to
disable each option separately.

Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-07-12 16:29:46 -07:00
Martin Schwidefsky
e25df1205f [S390] Kconfig: menus with depends on HAS_IOMEM.
Add "depends on HAS_IOMEM" to a number of menus to make them
disappear for s390 which does not have I/O memory.

Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
2007-05-10 15:46:07 +02:00
Jeff Garzik
5b2fc49991 Move USB network drivers to drivers/net/usb.
It is preferable to group drivers by usage (net, scsi, ATA, ...) than
by bus.  When reviewing drivers, the [PCI|USB|PCMCIA|...] maintainer
is probably less qualified on networking issues than a networking
maintainer.  Also, from a practical standpoint, chips often
appear on multiple buses, which is why we do not put drivers into
drivers/pci/net.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
2007-05-09 21:31:55 -04:00