This adds the low level irq tracing hooks to the powerpc architecture
needed to enable full lockdep functionality.
This is partly based on Johannes Berg's initial version. I removed
the asm trampoline that isn't needed (thus improving performance) and
modified all sorts of bits and pieces, reworking most of the assembly,
etc...
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds stacktrace support for powerpc, which will be needed for
lockdep.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves various definitions used all over the place to parse stack
frames to ptrace.h so only one definition is needed.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Lockdep found out that we can occasionally take the device-tree
lock for reading from softirq time (from rtas_token called
by the rtas real time clock code called by the NTP code),
while we take it occasionally for writing without masking
interrupts. The combination of those two can thus deadlock.
While some of those cases of interrupt read lock could be fixed
(such as caching the RTAS tokens) I figured that taking the
lock for writing is so rare (device-tree modification) that we
may as well penalize that case and allow reading from interrupts.
Thus, this turns all the writers to take the lock with irqs
masked to avoid the situation.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Add special cases for pplus and prep to ide_default_{irq,io_base}()
(+ FIXMEs about the need to use IDE platform host driver instead).
* Remove no longer needed ppc_ide_md and struct ide_machdep_calls.
* Then remove <linux/ide.h> include from:
- arch/powerpc/kernel/setup_32.c
- arch/ppc/kernel/ppc_ksyms.c
- arch/ppc/kernel/setup.c
- arch/ppc/platforms/pplus.c
- arch/ppc/platforms/prep_setup.c
There should be no functional changes caused by this patch.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
global_dbcr0 needs to be a per cpu set of save areas instead of a single
global on all processors.
Also, we switch to using DBCR0_IDM to determine if the user space app is
being debugged as its a more consistent way. In the future we should
support features like hardware breakpoint and watchpoints which will
have DBCR0_IDM set but not necessarily DBCR0_IC (single step).
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The architecture allows for "Book-E" style debug interrupts to either go
to critial interrupts of their own debug interrupt level. To allow for
a dynamic kernel to support machines of either type we want to be able to
compile in the interrupt handling code for both exception levels.
Towards this goal we renamed the debug handling macros to specify the
interrupt level in their name (DEBUG_CRIT_EXCEPTION/DebugCrit and
DEBUG_DEBUG_EXCEPTION/DebugDebug).
Additionally, on the Freescale Book-e parts we expanded the exception
stacks to cover the maximum case of needing three exception stacks (normal,
machine check and debug).
There is some kernel text space optimization to be gained if a kernel is
configured for a specific Freescale implementation but we aren't handling
that now to allow for the single kernel image support.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This changes the way we calculate how much space to reserve for the
pHyp dump. Currently we reserve 256MB only. With this change, the
code first checks to see if an amount has been specified on the boot
command line with the "phyp_dump_reserve_size" option, and if so, uses
that much.
Otherwise it computes 5% of total ram and rounds it down to a multiple
of 256MB, and uses the larger of that or 256MB.
This is for large systems with a lot of memory (10GB or more). The
aim is to have more space available for the kernel on reboot on
machines with more resources. Although the dump will be collected
pretty fast and the memory released really early on allowing the
machine to have the full memory available, this alleviates any issues
that can be caused by having way too little memory on very very large
systems during those few minutes.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We can set LOAD_OFFSET and use the AT attribute on sections and the
linker will properly set the physical address of the LOAD program
header for us.
This allows us to know how the PHYSICAL_START the user configured a
kernel with by just looking at the resulting vmlinux ELF.
This is pretty much stolen from how x86 does things in their linker
scripts.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* PAGE_OFFSET is not always the start of code, use _stext instead.
* grab PAGE_SIZE and KERNELBASE from asm/page.h like ppc64 does. Makes the
code a bit more common and provide a single place to manipulate the
defines for things like kdump.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
* Determine the RPN we are running the kernel at runtime rather
than using compile time constant for initial TLB
* Cleanup adjust_total_lowmem() to respect memstart_addr and
be a bit more clear on variables that are sizes vs addresses.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fedora 9 works on Efika without the separate 'device-tree supplement',
thanks to the kernel's own fixups. With one exception -- because 'CHRP'
still appears on the 'machine:' line in /proc/cpuinfo, the installer
misdetects the platform and misconfigures yaboot, putting it into a PReP
boot partition instead of in the /boot filesystem where the Efika's
firmware could find it.
The kernel's fixups for Efika already correct one instance of 'chrp', in
the 'device_type' property. This fixes it in the 'CODEGEN,description'
property too, since that's what's exposed to userspace in /proc/cpuinfo.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the handling of the preempt count when switching
interrupt stacks so that HW interrupt properly get the softirq
mask copied over from the previous stack.
It also initializes the softirq stack preempt_count to 0 instead
of SOFTIRQ_OFFSET, like x86, as __do_softirq() does the increment,
and we hit some lockdep checks if we have it twice.
That means we do run for a little while off the softirq stack
with the preempt-count set to 0, which could be deadly if we
try to take a softirq at that point, however we do so with
interrupts disabled, so I think we are ok.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Currently, we initialize the "current" pointer in the PACA (which
is used by the "current" macro in the kernel) before calling
setup_system(). That means that early_setup() is called with
current still "NULL" which is -not- a good idea. It happens to
work so far but breaks with lockdep when early code calls printk.
This changes it so that all PACAs are statically initialized with
__current pointing to the init task. For non-0 CPUs, this is fixed
up before use.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that we have the alpaca, the reg_save_ptr is no longer needed in the
paca. Eradicate all global uses of it and make it static in the iSeries
lpardata.c
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The iSeries HV only needs the first two fields of the paca statically
initialised, so create an alternate paca that contains only those and
switch to our real paca immediately after boot.
This is in order to make the 1024 cpu patches easier since they will no
longer have to statically initialise the pacas for iSeries.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
If an SLB miss interrupt happens while the RI bit of MSR is zero, we
can't just return, because RI being zero indicates that SRR0/SRR1
potentially had live values in them, and the process of taking an
interrupt overwrites them.
This should never happen, but if it does, we try to print a nice oops
message. That doesn't work, however, because the code at unrecov_slb
assumes that the MMU has been turned on, but we call it with the MMU
off (and have done so since the SLB miss handler was rewritten to run
without turning the MMU on) -- except on iSeries, where everything runs
with the MMU on.
This fixes it by adding the necessary code to turn the MMU on if
necessary.
Signed-off-by: Paul Mackerras <paulus@samba.org>
A couple of places are duplicating the function of
of_device_is_available; convert them to use it.
Signed-off-by: Nathan Lynch <ntl@pobox.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We have an assembly version of strncmp for the bootwrapper, but not
for the kernel, so we end up using the C version in the kernel. This
takes the strncmp code from the bootup and copies it to the kernel
proper, adding two instructions so it copes correctly with len==0.
Signed-off-by: Steven Rostedt <srostedt@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Handling of the proc_dir_entry->count was changed in 2.6.24-rc5.
After this change, the default value for pde->count is 1 and not 0 as
before. Therefore, if we want to check whether our procfs file is
already opened (already in use), we have to check if pde->count is
greater than 2 rather than 1.
Signed-off-by: Maxim Shchetynin <maxim@de.ibm.com>
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A subtle bug sneaked into iSeries recently. On this platform, we must
not normally clear MSR:EE (the hardware external interrupt enable)
except for short periods of time. Taking an interrupt while
soft-disabled doesn't cause us to clear it for example.
The iSeries kernel expects to mostly run with MSR:EE enabled at all
times except in a few exception entry/exit code paths. Thus
local_irq_enable() doesn't check if it needs to hard-enable as it
expects this to be unnecessary on iSeries.
However, hard_irq_disable() _does_ cause MSR:EE to be cleared,
including on iSeries. A call to it was recently added to the
context switch code, thus causing interrupts to become disabled
for a long periods of time, causing the iSeries watchdog to kick
in under some circumstances and other nasty things.
This patch fixes it by making local_irq_enable() properly re-enable
MSR:EE on iSeries. It basically removes a return statement here
to make iSeries use the same code path as everybody else. That does
mean that we might occasionally get spurious decrementer interrupts
but I don't think that matters.
Another option would have been to make hard_irq_disable() a nop
on iSeries but I didn't like it much, in case we have good reasons
to hard-disable.
Part of the patch is fixes to make sure the hard_enabled PACA field
is properly set on iSeries as it used not to be before, since it
was mostly unused.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Old-world powermacs don't set L2CR or L3CR on processor upgrade cards.
This simple patch allows the setting of L3CR via a kernel parameter
(like the existing kernel parameter to set L2CR).
Signed-off-by: Robert Brose <bob@qbjnet.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x1e4c0): Section mismatch in reference from the
function .move_device_tree() to the function .init.text:.lmb_alloc_base()
The function .move_device_tree() references
the function __init .lmb_alloc_base().
This is often because .move_device_tree lacks a __init
annotation or the annotation of .lmb_alloc_base is wrong.
move_device_tree() is called from early_init_devtree() only, which is __init
Signed-off-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
There is a bug in the powerpc DABR (data access breakpoint) handling,
which can result in us missing breakpoints if several threads are trying
to break on the same address.
The circumstances are that do_page_fault() calls do_dabr(), this clears
the DABR (sets it to 0) and sets up the signal which will report to
userspace that the DABR was hit. The do_signal() code will restore the DABR
value on the way out to userspace.
If we reschedule before calling do_signal(), __switch_to() will check the
cached DABR value and compare it to the new thread's value, if they match
we don't set the DABR in hardware.
So if two threads have the same DABR value, and we schedule from one to
the other after taking the interrupt for the first thread hitting the DABR,
the second thread will run without the DABR set in hardware.
The cleanest fix is to move the cache update into set_dabr(), that way we
can't forget to do it.
Reported-by: Jan Kratochvil <jan.kratochvil@redhat.com>
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds basic support for the AMCC 460EX/460GT PPC's to arch/powerpc.
Currently those PPC's are still based on a 440 core and *not* a 460 core.
Here some basic features of those SoC's:
460EX:
- Up to 1.2GHz, 32kB L1 I-cache and D-cache, 256kB L2-cache, FPU
- 1 * PCI (max 66MHz), 2 * PCIe (one 4-lane, one 1-lane)
- 2 * GBit Ethernet with TCP/IP acceleration
- USB 2.0 Host/Device OTG and Host interface
- SATA controller
- Optional security feature
460GT (only changes to 460EX):
- 4 * GBit Ethernet with TCP/IP acceleration
- RapidIO
- No SATA
- No USB
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This adds a kernel command line option "phyp_dump", which takes a 0/1
value for disabling/ enabling phyp_dump at boot time. Kdump can use
this on cmdline (phyp_dump=0) to disable phyp-dump during boot when
enabling itself. This will ensure only one dumping mechanism is active
at any given time.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Initial patch for reserving memory in early boot, and freeing it
later. If the previous boot had ended with a crash, the reserved
memory would contain a copy of the crashed kernel data.
Signed-off-by: Manish Ahuja <mahuja@us.ibm.com>
Signed-off-by: Linas Vepstas <linasvepstas@gmail.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
These items in asm-offsets.c are not used anywhere. This removes them.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PT_DTRACE flag is meaningless and obsolete.
Don't touch it.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
It was being protected by CONFIG_PPC32, but we want to export it on
64-bit also. This moves it out of the ifdef.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Print out 'model' property of '/' node as a machine name
in generic show_cpuinfo() routine.
Signed-off-by: Marian Balakowicz <m8@semihalf.com>
Acked-by: David Gibson <david@gibson.dropbear.id.au>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the PMU is an NMI now, it can come at any time we are only soft
disabled. We must hard disable around the two places we allow the kernel
stack SLB and r1 to go out of sync. Otherwise the PMU exception can
force a kernel stack SLB into another slot, which can lead to it
getting evicted, which can lead to a nasty unrecoverable SLB miss
in the exception entry code.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The PTRACE_SETREGS request was only recently added on powerpc,
and gdb does not use it. So it slipped through without getting
all the testing it should have had.
The user_regset changes had a simple bug in storing to all of
the 32-bit general registers block on 64-bit kernels. This bug
only comes up with PTRACE_SETREGS, not PPC_PTRACE_SETREGS.
It causes a BUG_ON to hit, so this fix needs to go in ASAP.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Once again, this time with feeling....
- Ted
>From c91cfaabc17f8a53807a2f31f067a732e34a1550 Mon Sep 17 00:00:00 2001
From: Theodore Ts'o <tytso@mit.edu>
Date: Wed, 12 Mar 2008 11:50:39 -0400
Subject: Export empty_zero_page
The empty_zero_page symbol is exported by most other architectures
(s390, ia64, x86, um), and an upcoming ext4 patch needs it because
ZERO_PAGE() references empty_zero_page, and we need it to zero out an
unitialized extents in ext4 files.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Paul Mackerras <paulus@samba.org>
A bogus test for unassigned resources that came from our 32-bit
PCI code ended up being "merged" by my previous patch series,
breaking some 64-bit setups where devices have legal resources
ending at 0xffffffff.
This fixes it by completely changing the test. We now test for
res->start == 0, as the generic code expects, and we also only
do so on platforms that don't have the PPC_PCI_PROBE_ONLY flag
set, as there are cases of pSeries and iSeries where it could
be a valid value and those can't reassign devices.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some drivers (such as V4L2) have code that causes gcc to generate
calls to __ucmpdi2 when compiling for 32-bit powerpc, which results
in either a link-time error or a module that can't be loaded, as
we don't currently have a __ucmpdi2. This adds one so these drivers
can be used.
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes swap routines operate correctly on the ppc_8xx based machines.
Code has been revalidated on mpc885ads (8M sdram) with recent kernel. Based
on patch from Yuri Tikhonov <yur@emcraft.com> to do the same on arch/ppc
instance.
Recent kernel's size makes swap feature very important on low-memory platforms,
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This code isn't referenced anywhere, so remove it.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
dt_mem_next_cell() currently does of_read_ulong(). This does not
allow for the case where #size-cells and/or #address-cells = 2 on a
32-bit system, as it will end up reading 32 bits instead of the
expected 64. Change it to use of_read_number instead and always
return a u64.
Signed-off-by: Becky Bruce <becky.bruce at freescale.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix sparse warnings in powerpc kprobes:
CHECK arch/powerpc/kernel/kprobes.c
arch/powerpc/kernel/kprobes.c:277:6: warning: symbol 'kretprobe_trampoline_holder' was not declared. Should it be static?
arch/powerpc/kernel/kprobes.c:287:15: warning: symbol 'trampoline_probe_handler' was not declared. Should it be static?
arch/powerpc/kernel/kprobes.c:525:16: warning: symbol 'jprobe_return_end' was not declared. Should it be static?
Fix along the same lines as http://lkml.org/lkml/2008/2/13/642
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This fixes the following section mismatches:
<-- snip -->
...
WARNING: vmlinux.o(.text+0xe49c): Section mismatch in reference from the function .vdso_do_func_patch64() to the function .init.text:.find_symbol64()
WARNING: vmlinux.o(.text+0xe4d0): Section mismatch in reference from the function .vdso_do_func_patch64() to the function .init.text:.find_symbol64()
WARNING: vmlinux.o(.text+0xe56c): Section mismatch in reference from the function .vdso_do_func_patch32() to the function .init.text:.find_symbol32()
WARNING: vmlinux.o(.text+0xe5a0): Section mismatch in reference from the function .vdso_do_func_patch32() to the function .init.text:.find_symbol32()
...
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The powerpc show_regs prints CPU using smp_processor_id: change that to
raw_smp_processor_id, so that when it's showing a WARN_ON backtrace without
preemption disabled, DEBUG_PREEMPT doesn't mess up that warning with its own.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Commit ad7f71674a ("[POWERPC] Use a
sensible default for clock_getres() in the VDSO") corrected the clock
resolution reported by the VDSO clock_getres() but introduced another
problem in that older versions of gcc (gcc-4.0 and earlier) fail to
compile the new code in arch/powerpc/kernel/asm-offsets.c.
This fixes it by introducing a new MONOTONIC_RES_NSEC define in the
generic code which is equivalent to KTIME_MONOTONIC_RES but is just an
integer constant, not a ktime union.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This makes the SPE register data appear in ELF core dumps, using the
new n_type value NT_PPC_SPE (0x101). This new note type is not used
by any consumers of core files yet, but support can be added. I don't
even have any hardware with SPE capabilities, so I've never seen such
a note. But this demonstrates how simple it is to export register
information in core dumps when the user_regset style is used for the
low-level code.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleans up the 32-bit ptrace syscall support to use user_regset calls
to get at the register data for PTRACE_*REGS* calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces powerpc's compat_sys_ptrace with a compat_arch_ptrace and
enables the new generic definition of compat_sys_ptrace instead.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This removes some duplicated code by calling the new generic
compat_ptrace_request from powerpc's compat_sys_ptrace.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that ptrace_request handles these, we can drop some more boilerplate.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This replaces all the code for powerpc PTRACE_*REGS* requests with
simple calls to copy_regset_from_user and copy_regset_to_user. All
the ptrace formats are either the whole corresponding user_regset
format (core dump format) or a leading subset of it, so we can get
rid of all the remaining embedded knowledge of both those layouts
and of the internal data structures they correspond to. Only the
user_regset accessors need to implement that.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This switches the CONFIG_PPC64 support for 32-bit ELF to use the
generic fs/compat_binfmt_elf.c implementation instead of our own
binfmt_elf32.c. Since so much is the same between 32/64, there is
only one macro we have to define to make the generic support work out
of the box.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This extends task_user_regset_view CONFIG_PPC64 with support for the
32-bit view of register state, compatible with what a CONFIG_PPC32
kernel provides. This will enable generic machine-independent code to
access user-mode threads' registers for debugging and dumping.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This provides the task_user_regset_view entry point and support for
all the native-mode (64 on CONFIG_PPC64, 32 on CONFIG_PPC32) thread
register state. This will enable generic machine-independent code to
access user-mode threads' registers for debugging and dumping.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc general
registers. In the future these functions will be the only place that
needs to understand the user_regset layout (core dump format) and how
it maps to the internal representation of user thread state.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This isolates the ptrace code for the special-case registers msr and trap
from the ptrace-layout dispatch code. This should inline away completely.
It cleanly separates the low-level machine magic that has to be done for
deep reasons, from the superficial details of the ptrace interface.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc SPE data,
and rewrites the existing ptrace code in terms of those calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc Altivec data,
and rewrites the existing ptrace code in terms of those calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This implements user_regset-style accessors for the powerpc FPU data,
and rewrites the existing ptrace code in terms of those calls.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Looks like "[POWERPC] kdump shutdown hook support" broke builds when
CONFIG_DEBUGGER=n and CONFIG_KEXEC=y, such as in g5_defconfig:
arch/powerpc/kernel/crash.c: In function 'default_machine_crash_shutdown':
arch/powerpc/kernel/crash.c:388: error: '__debugger_fault_handler' undeclared (first use in this function)
arch/powerpc/kernel/crash.c:388: error: (Each undeclared identifier is reported only once
arch/powerpc/kernel/crash.c:388: error: for each function it appears in.)
Move the debugger hooks to under CONFIG_DEBUGGER || CONFIG_KEXEC, since
that's when the crash code is enabled.
(I should have caught this with my build-script pre-merge, my bad. :( )
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This moves the ability to scale cputime into generic code. This allows us
to fix the issue in kernel/timer.c (noticed by Balbir) where we could only
add an unscaled value to the scaled utime/stime.
This adds a cputime_to_scaled function. As before, the POWERPC version
does the scaling based on the last SPURR/PURR ratio calculated. The
generic and s390 (only other arch to implement asm/cputime.h) versions are
both NOPs.
Also moves the SPURR and PURR snapshots closer.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: Jay Lan <jlan@engr.sgi.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The e300 c3 and c4 variants support hardware performance monitor counters
which are identical to those found in the e500.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Some of the more recent e300 cores have the same performance monitor
implementation as the e500. e300 isn't book-e, so the name isn't
really appropriate. In preparation for e300 support, rename a bunch
of fsl_booke things to say fsl_emb (Freescale Embedded Performance Monitors).
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The patch to legacy_serial.c (1a7507c7da,
Reduce code duplication in legacy_serial, add UART parent types) changed
the semantics for opb ports from type = "opb" || compatible = "ibm,opb"
to type = "opb" && compatible = "ibm,opb".
The result is serial ports on our QS21s (Cell blades) don't get found,
and for some reason the machine doesn't boot at all - possibly it's
panicking due to lack of a console?
The fix is to add two entries to the of_device_id table, one that looks
for type = "opb" and the other compatible = "ibm,opb".
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This ensures that the syscall and the (fast) vdso versions of
clock_getres() will return the same resolution.
Signed-off-by: Tony Breeds <tony@bakeyournoodle.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
WARNING: vmlinux.o(.text+0x3017c): Section mismatch in reference from the function .vio_create_viodasd() to the function .devinit.text:.vio_register_device_node()
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Previously, during initialization of the IOMMU tables, the last entry
at each 4GB boundary is marked as used since there are many adapters
which cannot handle DMAing across any 4GB boundary.
The IOMMU doesn't allocate a memory area spanning LLD's segment
boundary anymore. The segment boundary of devices are set to 4GB by
default. So we can remove 4GB boundary protection now.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch converts PPC's IOMMU to use the IOMMU helper functions. The IOMMU
doesn't allocate a memory area spanning LLD's segment boundary anymore.
iseries_hv_alloc and iseries_hv_map don't have proper device
struct. 4GB boundary is used for them.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-2.6:
PPC: Fix powerpc vio_find_name to not use devices_subsys
Driver core: add bus_find_device_by_name function
Module: check to see if we have a built in module with the same name
x86: fix runtime error in arch/x86/kernel/cpu/mcheck/mce_amd_64.c
Driver core: Fix up build when CONFIG_BLOCK=N
This removes the handling for PTRACE_CONT et al from the powerpc
ptrace code, so it uses the new generic code via ptrace_request.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This defines the new standard arch_has_single_step macro. It makes the
existing set_single_step and clear_single_step entry points global, and
renames them to the new standard names user_enable_single_step and
user_disable_single_step, respectively.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove the deprecated __attribute_used__.
[Introduce __section in a few places to silence checkpatch /sam]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This patch consolidate all definitions of .init.text, .init.data
and .exit.text, .exit.data section definitions in
the generic vmlinux.lds.h.
This is a preparational patch - alone it does not buy
us much good.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
All current 85xx/e500 implementations only have two TLB
arrays. We are wasting cycles by invalidating TLB2 and TLB3.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The legacy_serial was treating each UART parent in a separate code block.
Rather than continue this trend for the new parent IDs, this condenses
all (soc, tsi, opb, plus two more new types) into one of_device_id array.
The new types are wrs,epld-localbus for the Wind River sbc8560, and a
more generic "simple-bus" as requested by Scott Wood.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
This fixes vio_find_name() in arch/powerpc/kernel/vio.c, which is
currently broken because it tries to use devices_subsys. That is bad
for two reasons: (1) it's doing (or trying to do) a scan of all
devices when it should only be scanning those on the vio bus, and
(2) devices_subsys was an internal symbol of the device system code
which was never meant for external use and has now gone away, and
thus the kernel fails to compile on pSeries.
The new version uses bus_find_device_by_name() on the vio bus
(vio_bus_type).
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Prune back Efika fixups to only include changes that are actually required
to get a working system. Most of the drivers can accept the compatible
properties, even if they don't match the what is recommented in the generic
names recommended practice document.
This patch also adds extra checks so that fixups are not performed blindly.
Instead, the code first verifies that the device tree is faulty before
making any changes. This way, if the Efika firmware is updated to fix
these issues, then the fixups will no longer get applied.
At this point; here is the list of fixups needed for the efika:
1. If the device_type property on the root node is 'chrp', then Linux won't
boot. Change device_type to 'efika' to avoid this condition
2. Add full interrupt list to the bestcomm node. In actual fact, the
bestcomm interrupts property is technically correct, it just doesn't
expose the same granularity as the device driver expects. All other
5200 device trees provide a separate irq number for each bestcomm
channel. Rather than hack the driver, it's simpler to fix it up
3. /builtin/sound node is missing an interrupts property
4. /builtin/ethernet node is missing a phy-handle property and the
device driver doesn't know what to do without one.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This adds the 440EP revision C PVR to the CPU table. The chip has an
FPU on it, so we also match the logical PVR
Signed-off-by: Sean MacLennan <smaclennan@pikatech.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch adds the 405EXr to the powerpc cuptable. Basically the 405EXr
is a 405EX with only one EMAC and only one PCIe interface.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since commit c80d9133e9 (Make direct DMA use
node local allocations) went in this comment makes no sense.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We no longer need the global dma_direct_offset, update the comment to
reflect the new reality.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Now that all platforms using dma_direct_offset setup the
archdata.dma_data correctly, we can change the dma_direct_ops to
retrieve the offset from the dma_data, rather than directly from the
global.
While we're here, change the way the offset is used - instead of
or'ing it into the value, add it. This should have no effect on
current implementations where the offset is far larger than memory,
however in future we may want to use smaller offsets.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
We must always hookup the pci_bus resource 0 to the PHB io_resource
even if the latter is empty (the bus has no IO support). Otherwise,
some other code will end up hooking it up to something bogus and the
resource tree will end up being broken.
This fixes boot on QS20 Cell blades where the IDE driver failed to
allocate the IO resources due to breakage of the resource tree.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds hooks into the default_machine_crash_shutdown so drivers can
register a function to be run in the first kernel before we hand off
to the second kernel. This should only be used in exceptional
circumstances, like where the device can't be reset in the second
kernel alone (as is the case with eHEA). To emphasize this, the
number of handles allowed to be registered is currently #def to 1.
This uses the setjmp/longjmp code around the call out to the
registered hooks, so any bogus exceptions we encounter will hopefully
be recoverable.
Tested with bogus data and instruction exceptions.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the setjmp/longjmp code used by xmon, generically available
to other code. It also removes the requirement for debugger hooks to
be only called on 0x300 (data storage) exception.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
