This patch adds digital ATSC / QAM support for the DViCO FusionHDTV5 Express.
Remote control is supported by ir-kbd-i2c, RTC is supported by rtc-isl1208.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Changes to support MPEG TS on VIDB
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Changes to support interrupts on VIDB
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
start_dma() would fail to start dma if a device used VIDB (portb).
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The switch() statement is no longer required.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The HVR1250 and HVR1800 boards need the s5h1409 demod GPIO enabled.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Reviewed-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Not sure why they are there, but they don't do anything now.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use the balance control to make the mono volume control stereo.
Note that full range isn't supported. The balance control attenuates one
channel by 0 to -63 dB, and the volume control provides additional attenuation
to both channels by another 0 to -63 dB.
So the channel with the most attenuation has a range of 0 to -126 dB, while
the other channel only has a range of 0 to -63 dB. ALSA volume controls don't
appear to support this concept. I just limited the range to 0 to -63 total.
Once you get to -63 dB, you're already at silence, so additional attenuation
is pretty much pointless anyway.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Auto-load ir-kbd-i2c for ir receiver support, and rtc-isl1208 for rtc
support for the FusionHDTV5 RT Gold.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Ignore 0x6b and 0x6f on cx88 boards. Some FusionHDTV cards
have an ir receiver at 0x6b and an RTC at 0x6f which can
get corrupted if probed.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fixed missing buttons in keymap.
- make function names & descriptions more generic,
since this same ir receiver and remote is used in
many FusionHDTV products.
- miscellaneous cleanups.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for the built-in IR receiver of the DViCO
Fusion HDTV5 RT GOLD PCI card, using FusionHDTV MCE remote controller.
Signed-off-by: Chaogui Zhang <czhang1974@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I wanted to document the NMI assert issue inside the code, even though
it's already documented in the patch history. If/when the next cx23887
revision appears, is may need to be enabled on that also.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A number of Hauppauge boards share the same tuner and demod
configurations. This patch removes duplicate structures.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moving some defines into the correct header file.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding support for the Hauppauge HVR1250 PCIe ATSC board.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Changed the pci_quirks function to detech the bridge type before setting
the NMI clear bit, rather than detecting based on unique board id.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The pci_quirks function was being called too early during initialisation,
it needs to be called after the board has been identified.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Turn off i2c_debug by default, to make the driver less verbose.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The dvb-pll module is not being used by this driver.
Remove the unneeded #include.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The mt2131 tuner reports lock even when the hardware should not
lock. This patch allows the s5h1409 demodulator to be configured to query
either the tuner driver for status, or the demodulator status when the
application requests lock status. This avoids returning false CARRIER
and/or SIGNAL lock status.
S5H1409 and MT2131 drivers. This is the remainder of the changeset, which
only touches cx23885-dvb.c
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Moved the field from cx23885_board to cx23885_dev and added code to
iautomatically set the bridge type based on the pci device id.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is required to support the cx258xx family of audio and video decoders.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx23885 and cx23887 family use two different memory maps which govern
how the internal SRAM is configured. This patch streamlines the access to those
structures.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The sram allocations for the cx23887 differ slightly from the cx23885.
This patch modifies the cx23887 specific sram memory map to reflect this.
As a result, interrupts and DMA handling have also been enabled in
cx23885_start_dma() for 887 specific boards.
ATSC streaming is now available on cx23885 and cx23887 bridges.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
I2C bus 3 was being initialised with the incorrect address register.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- fix #include for <media/video-buf-dvb.h>
- fix cx23885_irq declaration for 2.6.19 and later
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a new framework to support boards based on the CX23885/7 PCIe
bridge. The framework supports digital (no analog yet)
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix the following build warning:
CC [M] cx25840-core.o
cx25840-core.c: In function 'init_dll1':
cx25840-core.c:147: warning: implicit declaration of function 'udelay'
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Break tuner.ko into separate modules. This was a quick change -
Tuner sub-drivers are still static-linked to tuner.ko, this will
change after using dvb_attach and removing the probing functions.
After this change, one can deselect undesired tuner sub-drivers via Kconfig.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mike Isely <isely@pobox.com>
Acked-by: Steven Toth <stoth@hauppauge.com>
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mike Isely <isely@pobox.com>
Acked-by: Steven Toth <stoth@hauppauge.com>
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mike Isely <isely@pobox.com>
Acked-by: Steven Toth <stoth@hauppauge.com>
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Prepare tuner-core for conversion of tuner sub-drivers into
dvb_frontend modules
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mike Isely <isely@pobox.com>
Acked-by: Steven Toth <stoth@hauppauge.com>
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Acked-by: Oliver Endriss <o.endriss@gmx.de>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
To ease the conversion of the analog tuner sub-drivers into dvb_frontend
style tuner modules, we must remove the i2c_client interface.
dvb_frontend style tuner modules use i2c_transfer directly on the i2c_adapter.
This change only alters the interface between tuner.ko and the tuner
sub-drivers. The v4l2 / i2c_client interface to tuner.ko remains intact.
This patch adds inline functions tuner_i2c_xfer_send, and tuner_i2c_xfer_recv,
to replace i2c_master_send and i2c_master_recv inside the tuner sub-drivers.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Mike Isely <isely@pobox.com>
Acked-by: Steven Toth <stoth@hauppauge.com>
Acked-by: Patrick Boettcher <pb@linuxtv.org>
Acked-by: Jarod Wilson <jwilson@redhat.com>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The tuner module has a rather aggressive range of possible i2c addresses.
As per the specs available, it appears as if there are no 4-byte tuners that
actually use i2c addresses in the range 0x64 thru 0x6f, yet, tuner-core claims
the address range 0x60 thru 0x6f.
Allowing tuner.ko to probe these addresses can cause potential damage to
certain IR receivers, RTC chips or any other IC's that might otherwise reside
on the i2c bus using one of these addresses.
The plan is to remove these i2c addresses from the i2c address range of the
tuner module. If any devices are discovered that actually do have tuners at
one of these addresses, the newer i2c probing methods will be used to handle
those cases.
In order to collect this information and avoid any potential regressions,
the following warning has been added upon successful detection of a tuner
using an i2c address in the range 0x64 thru 0x6f:
====================== WARNING! ======================
Support for tuners in i2c address range 0x64 thru 0x6f
will soon be dropped. This message indicates that your
hardware has a {tuner name} tuner at i2c address {addr}.
To ensure continued support for your device, please
send a copy of this message, along with full dmesg
output to v4l-dvb-maintainer@linuxtv.org
Please use subject line: "obsolete tuner i2c address."
====================== WARNING! ======================
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were many instances of 7-space indents spread throughout
the v4l-dvb tree.
This patch replaces the 7-space indents with tabs. The whitespace cleaner
script doesn't catch these, because it assumes that all indents are 8-space.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There were a couple of places in the cx25840 initialization where the
datasheet called for a 10 microsecond delay, which we ignored because
of the 10 usec I2C delay. Put them in anyway now that the I2C delay
was decreased to 5 usec.
Signed-off-by: Tyler Trafford <ttrafford@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtvfb: replace ivtv_fb prefix to ivtvfb, change warning to info message
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The convention for framebuffer devices is to call them xxxfb, not xxx-fb.
Conform to this. Also move the ivtvfb.h header to include/linux: it is a
public header. The FBIO_WAITFORVSYNC ioctl is now also defined in the
ivtvfb.h header, no more need to include matroxfb.h for just this ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Besides some VBI cleanups this patch also fixes a subtle problem with the
VBI re-insertion stream where the PIO work handler wasn't called quickly
enough, resulting in occasional corrupt data.
Furthermore the CC output didn't disable CC correctly and at the right time,
causing duplicates to be sent.
An saa7127 fix for VPS output was also added: the wrong data was sent.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An udelay of 5 is sufficient for standard speed i2c busses, 10 make it
too slow.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Loading the firmware using the i2c bit-banging code blocks the kernel.
Move the firmware load code into a workqueue so that it plays well with
other processes.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tcm825x.c: In function 'ioctl_try_fmt_cap':
tcm825x.c:639: warning: format '%d' expects type 'int', but argument 4
has type 'long unsigned int'
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since kzalloc() returns a void pointer, we don't need to cast the
return value in drivers/media/video/ivtv/ivtv-queue.c
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv: set correct pixel format and alpha properties in VIDIOC_G_FBUF
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Support for V4L2_ENC_CMD_STOP_AT_GOP_END was broken. While the driver
correctly waited for the card to capture until the GOP was complete,
afterwards the driver buffers were just flushed instead of waiting
for the application to read all the pending data.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver should now pass the 'busy' state of the device to the cx2341x
module whenever controls are set or tried. -EBUSY will be returned if
the device is busy and the user attempts to modify certain 'dangerous'
controls. It concerns controls that change the audio or video
compression mode and bitrates.
The cx88-blackbird and pvrusb2 drivers currently always pass '0' (not busy)
to the cx2341x, effectively keeping the old behavior for now.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Changing the VBI format requires a CX2341X_ENC_INITIALIZE_INPUT firmware
call. This can only be done if no capture is in progress. So return
-EBUSY if the encoder is busy.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Always clear when stopping the decoder
- Clear if the filehandle that is being close was used for UDMA_YUV output.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver has long claimed to support mmap, but it didn't work at all. Some
of the dma buffer parameters weren't set, and since video_buf uses vmalloc to
allocate the buffer, a page callback is needed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver kepts a static global array of snd_card pointers for each card
probed, which was never used.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Rework the way the DMA buffer is handled and IRQs are generated.
ALSA uses a ring-buffer of multiple periods. Each period is supposed to
corrispond to one IRQ.
The existing driver was generating one interrupt per ring-buffer, as opposed
to per period. This meant that as soon as the IRQ was generated, the hardware
was already starting to re-write the beginning of the buffer. Since the DMA
happens on a per-line basis, there was only a narrow window to copy the data
out before the buffer was overwritten.
The cx88 core RISC program generator is modified so that it can set the IRQ
and counter flags to count every X lines of DMA transfer. This way we can
generate an interrupt every period instead of every full ring-buffer. Right
now only period of one line are supported, but it should be possible to
support longer periods. Note that a WRITE instruction generates an IRQ when
it starts, not when the transfer is finished. Thus to generate an IRQ when
line X is done, one must set the IRQ flag on the instruction that starts line
X+1, not the one that ends line X.
Change the line size so that there are four lines in the SRAM FIFO. If there
are not four lines, the analog output from the cx88's internal DACs is full of
clicks and pops.
Try to handle FIFO sync errors. Sometimes the chip generates many of these
errors before audio data starts. Up to 50 sync errors will be ignored and the
counter reset.
Have the IRQ handler save the RISC counter to the chip struct, and then have
the pointer callback use this to calculate the pointer position. We could
read the counter from the pointer callback, but sometimes the sync errors on
start up cause the counter to go crazy. ALSA sees this and thinks there has
been an overrun. The IRQ hander can avoid saving the counter position on
sync errors.
The chip "opened" flag wasn't necessary. ALSA won't try to open the same
substream multiple times. Probably this code was cut&pasted from the bt87x
driver, which has multiple sub-streams for one chip.
Do error checking for the videobuf mapping functions.
snd_card_cx88_runtime_free() is useless and can be deleted.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Convert the initialization of ivtv_i2c_algo_template to C99-style.
Otherwise a future change to struct i2c_algo_bit_data would break
this code.
Also declared that structure const - it's a template after all.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since at least kernel 2.6.12-rc2, module.h includes moduleparm.h. This
patch removes all occurences of moduleparm.h from drivers/media files.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The file, tuner-driver.h was originally named tuner-hw.h, but we decided to
rename it. At the time, I had forgotten to change the #ifdef __TUNER_HW_H__
to #ifdef __TUNER_DRIVER_H__ . This patch corrects that.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add DVB-T support for Avermedia Super 007
Analog television is untested. The device lacks input adapters for radio,
svideo & composite -- seems to be a DVB-T ONLY device.
Signed-off-by: Edgar Simo <bobbens@gmail.com>
Acked-by: Hermann Pitton <hermann-pitton@arcor.de>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This is a simple whitespace cleanup.
Signed-off-by: Edgar Simo <bobbens@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The revision is part of the pci_dev struct, so there is no need to read it in.
Stop storing the revision and latency in the chip struct, since they're never
used after being printed out when the driver loads.
linux/pci.h wasn't included. It was getting picked up something else,
probably cx88.h, but this file uses struct pci_dev so it should include pci.h.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
channels_min should be 2, not 1. The hardware only supports stereo.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Currently the driver turns on audio interrupts, then sets the audio interrupt
mask to select which interrupts to get. One could received unwanted
interrupts since the mask is set _after_ interrupts have already been turned
on. Change the order of the operations, and clear any audio interrupt status
bits that are already set for good measure.
Before changing the SRAM FIFO parameters, make sure the FIFO isn't being used.
This shouldn't happen with just the ALSA driver, as it should never try to
turn on FIFO/RISC/DMA while they are already on. However, the V4L driver
needs to turn the audio FIFO on for analog audio output to work (undocumented
cx88 bug). The FIFO parameters are in an inconsistent state while they are
updated, and this results in many FIFO sync error IRQs if the FIFO is in use
while it's in this inconsistent state.
Also create and use a bunch of symbolic constants for audio interrupt mask
bits.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When an irq handled by the cx88 core driver (currently IR and errors) occurs
and the cx88-alsa irq handler is the first called, it will claim to have
handled the irq but it doesn't call cx88_core_irq() to handle it.
The means loading cx88-alsa can disable the IR remote.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Used for the PCI_INTMSK and PCI_INT_STAT registers.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add VIDIOC_OVERLAY to enable/disable the OSD. Also add the OSD state to the
log status report.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The return value of ivtv_udma_fill_sg_list() was changed by the
highmem bugfix, but that return value was still used in ivtv-yuv.c.
Revert to the old return value, but in addition return -1 in case of
a memory allocation error.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When trying to DMA userspace buffers to the cx23415 you need to check
whether the page is in highmem. If this is the case, then bounce buffers
have to be used to allow DMA.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Serialization is now done on the open/close/ioctl level and also when the
read/write/poll start an encoder/decoder stream.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- add FILE debug flag for open/close/read/write/poll.
- show cmd for encoder/decoder command ioctl.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some streams (PCM, VBI decoding) do not need that much memory, so specify
the allocated memory in kB instead of MB to limit memory usage. E.g. 1 MB
is overkill for the VBI decoding stream, 64 kB is enough.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The TV output standard was set only on first use, which meant that the saa7127
was set to NTSC until then, leading to flickering on PAL systems.
Since the saa7127 has no firmware it is OK to initialize it immediately.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Whenever the 0x80b register is used the microcontroller should be reset.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Give up frame after three retries.
- When the last capture/decode ends, make sure to delete the dma_timer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Invalid VBI packets should result in an empty VBI frame, not
in an zero-sized frame that causes the reader to incorrectly
return a 0 (EOF) value.
- PIO completion should not reset the sg_pending_size field.
- The DMA offset detection code should be ignored for PIO transfers:
it somehow messes up the data on the card and is not needed anyway
for PIO.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
It turns out that the cx23415/6 DMA engine cannot do scatter/gather DMA
reliably. Every so often depending on the phase of the moon and your
hardware configuration the cx2341x DMA engine simply chokes on it and
you have to reboot to get it working again.
This change replaced the scatter/gather DMA by single transfers at a time,
where the driver is now responsible for DMA-ing each buffer.
UDMA is still done using scatter/gather DMA, that will be fixed soon.
Many thanks to Mark Bryars <mark.bryars@etvinteractive.com> for discovering
the link between scatter/gather and the DMA timeouts.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When there are no more free buffers, then buffers are stolen from the
predma queue. Buffers should be stolen from the head of that queue (which
is where the most recently added buffers are) and all buffers belonging
to a frame should be stolen. Otherwise 'half-frames' would remain in the
queue, which leads to ugly playback and complete sync failure for YUV
buffers.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The CX2341X_ENC_INITIALIZE_INPUT firmware call requires careful handling,
otherwise the computer can freeze or the top-third of the screen can start
flickering. This patch ensures that CX2341X_ENC_INITIALIZE_INPUT is called
at the right time and in the right way.
In addition the stop capture handling was improved so that the last pending
DMA transfer is also processed. Otherwise this would be the first data that
arrived when a new capture was started which is not what you want.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
FM radio transmission use a preemphasis/deemphasis scheme to reduce
high-frequency noise. The cx88 audio decoder is supposedly set to no
deemphasis by the current driver.
However, the "no deemphasis" setting doesn't work. On my chip, cx23883, it
produces the same result as the 75 us time constant. Maybe the default
settings on the cx23881 are for 50 us?
Since the deemphasis time constant varies by country, allow setting it via a
module parameter.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Get rid of the "CORE" prefix from cx88 printks. It was only used a few times,
and it makes it look like they're coming from the kernel core or something.
Fix the message, "TV tuner 60 at 0x1fe, Radio tuner -1 at 0x1fe", by adding a
"cx88[0]" prefix to be consistent, and to keep people who grep their dmesg
output for cx88 from missing it. Get rid of the addresses, which are always
wrong. The addresses are always set to -1, but because it's an unsigned 8-bit
value, the left shift converts it to the nonsense address 0x1fe.
In the cx8802 driver, some cut and pasted code prefixed lines with "CORE
cx88[0]:", which has been changed to "cx88[0]/2:" like the other printks from
the cx8802 driver.
Also fix some ugly printks in the cx8802 driver that used __FUNCTION__ for
KERN_INFO and KERN_ERR messages.
The changed printks in cx88-mpeg.c also needed lots of whitespace and
80-column fixes.
A bunch of misc changes in cx88-dvb.c and cx88-video.c to add message levels
or a consistent "cx88[?]/2" or "cx88[?]/0" prefix.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A lot of code in cx88-cards.c was only used by cx88-core.c when the core state
is first allocated and initialized. Moving that task to cx88-cards makes the
driver simpler and the files more self contained.
- Module parameters tuner, radio, card, and latency move to cx88-cards.c
- cx88_boards is made static
- cx88_subids is made static and const
- cx88_bcount is eliminated
- cx88_idcount is eliminated
- cx88_card_list() is made static
- cx88_card_setup_pre_i2c() is made static
- cx88_card_setup() is made static
- cx88_pci_quirks() is moved from cx88-core to cx88-cards
The function argument "char *name" is made const too
- get_ressources() is moved from cx88-core to cx88-cards, and renamed to
cx88_get_resources()
- The code to allocate and initialize the core state struct and the chip is
moved out of cx88-core.c:cx88_get_core() and into a new function in
cx88-cards.c, cx88_core_create(). This makes both functions simpler.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The cx88 driver state stored the ID of the board type in core->board. Every
time the driver need to get some information about the board configuration, it
uses the board number as an index into board configuration array.
This patch changes it so that the board number is in core->boardnr, and
core->board is a copy of the board configuration information. This allows
access to board information without the extra indirection. e.g.
cx88_boards[core->board].mpeg becomes core->board.mpeg.
This has a number of advantages:
- The code is simpler to write.
- It compiles to be smaller and faster, without needing the extra array lookup
to get at the board information.
- The cx88_boards array no longer needs to be exported to all cx88 modules.
- The boards array can be made const
- It should be possible to avoid keeping the (large) cx88_boards array around
after the module is loaded.
- If module parameters or eeprom info override some board configuration
setting, it's not necessary to modify the boards array, which would
affect all boards of the same type.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An error message for PCI resource allocation failure used the board type
before it was set. Just get rid of the error message, as get_ressources()
[sic] already prints one. Format that error message better, and add the pci
function and subsystem information to better associate the error with what
caused it.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The vmux setting is only two bits, but was taking up a whole 32
in the input description struct. By changing it to a two-bit
bitfield, it can fit in what was padding space before and drop
the input size by 4 bytes, from 28 to 24. This drops the board
description struct, which has 9 inputs, from 280 to 244 bytes.
Total driver size decreases by 2108 bytes.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
tuner-simple is the only sub-driver that uses last_div, so we
can free up two bytes of memory for all other tuners, by moving
this into tuner-simple's private data area.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Some lines later filp->private_data is initialized to dev again.
Since there are some checks that might fail in the mean time
keep the later version.
Signed-off-by: Rolf Eike Beer <eike-kernel@sf-tec.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly attribute the origin of the driver to Kazuhiko
Kawakami.
It took some time to get the S-O-B line from the original
tvaudio patch author, but here it is.
Signed-off-by: Kazuhiko Kawakami <kazz-0@mail.goo.ne.jp>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When changing channels the audio has to be muted. This is done
by calling CX2341X_ENC_MUTE_AUDIO and by muted the audio input.
The latter is not necessary and is now removed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Audio muting for the tuner input was implemented by stopping the
audio microcontroller and restarting it on unmute. However, it
appears that this method can actually crash the audio firmware.
It's rare and seems to happen with NTSC only.
It has been reimplemented by setting to volume to 0. In addition, the
reporting of the mute state has been improved as well: it used to be
impossible to detect whether the audio was muted by the user or if it
was muted due to the microcontroller trying to detect the audio
standard. This is now clearly stated.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- Split Club3D card from Yuan PG600-2, GotView PCI DVD Lite
(different composite input)
- Add AVerTV MCE 116 Plus (M116) card
- Allow Xceive cards to be used without Xceive support
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support to optionally reset the IR and/or the video digitizer.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Resetting without reloading the firmware is not enough. Sometimes the
firmware is 'stuck' and needs to be reloaded.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
With the addition of these ioctls, I'm able to watch TV with a 32-bit version
of tvtime on x86_64.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since videobuf_waiton is called with intr=1, it can return -EINTR and therefore
err may be non-zero. This happens when the system goes into the standby state.
Without the BUG() occurring, there's no problem with standby mode while DVB
is being used.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Looks like memset() is zeroing wrong nr of bytes.
Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add radio support for the Thomson DTT7612 tuner.
This tuner uses a different 1st intermediate frequency than the other radio
tuners supported (a lot of NTSC radio tuners probably need this change too).
Add a new tuner-simple parameter, radio_if. It selects the 1st IF used for
radio reception. The radio frequency setting code in tuner-simple now uses
this field, instead of a special case select() block for each tuner with radio
support.
The tuner parameters for tuners that used a 33.3 MHz RIF now set radio_if to 1
in tuner-types.c.
The Thomson DTT7612 gets radio_if = 2, also add has_tda9887 = 1 and
fm_gain_normal = 1.
Add some defines for tda9887 bits that control IF setting in radio mode.
Add a new tda9887 config option, TDA9887_RIF_41_3, that selects a 41.3 MHz
radio IF.
Fix the way tda9887 radio options work. The driver was modifying the default
radio mode config templates based on the TDA9887_XXXX flags. This means that
_all_ tuners would get the same settings. If you had a one tuner than used
TDA9887_GAIN_NORMAL and one that didn't, both would get the setting. Now the
tda9987 driver just checks if tuner mode is radio and then applies the config
settings directly to the data being sent, just like how all the TV mode
settings already work.
The PLL setting math is made a little more accurate.
And a grammar error in a printk is fixed.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the advanced debug functions to the radio videodev template. One could
already use them from the video and vbi devices.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
After some tedious work with a logic probe and a magnifying glass, I've
determined that GPIO 7 is used to switch between the DTT7612's Sound 4.5 MHz
IF output on pin 12 and the FM 10.7MHz If output on pin 11. GPIO 2 is used to
switch the card's analog sound output from from the analog input connector to
the CX23883's audio DACs.
So, in radio mode GPIO2 = 1 and GPIO7 = 0.
Add some comments about how the HD-3000's GPIOs are connected.
Delete the vmux setting for the radio, as vmux doesn't apply to radio mode.
Also delete the lines setting unused gpio words to zero; it's not necessary as
0 is the default value for uninitialized fields.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
In the current driver, the field order is global. As soon as it's changed it
takes immediate effect. This is a problem when the video changes order mid
stream. Although it mostly works okay, the video may judder / flicker.
This patch attaches the field order to the frame, so that any buffered frames
will not be displayed until the correct field. In the event that the field
order is changed mid stream, the driver will ensure that the previous frame
is displayed for a minimum of 3 fields. These are the two original fields the
frame should have occupied, plus the one extra since the new frame still has
to wait for the correct field.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The yuv output code always compares the new frame position & size with those
of the previous frame. If they are different, a flag is set to request the
yuv output registers be updated when the new frame is displayed.
If the incoming frames are delivered too fast, exhausting the buffers, the
most recent frame already buffered will be discarded. Unfortunately, any
update request will also be discarded. If the new frame matches the size &
position of the now discarded frame, the yuv registers are not flagged for
update & will remain in their old state.
This patch preserves the register update flag in the event that a frame is
dropped.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Framebuffer timings are currently locked to the video format in use when the
module is loaded. If the video format is then changed, the timings returned
by the framebuffer will be for the original format.
This patch ensures that the timings returned reflect the current video format.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When the video standard is changed, there's no guarantee the framebuffer
dimensions are still legal. The yuv output code uses these dimensions to
calculate the size & position for the video overlay. If the framebuffer
dimensions are now illegal, the output may exceed the vertical limit of the
display, causing distortion.
This patch adds an additional check to ensure the output doesn't exceed
the limits for the current video standard, cropping if required.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This device is internal to the Panasonic VP27S tuner and is used to set
the mono/stereo/bilingual setting of the tuner.
It is used by two Japanese cx23416-based cards.
Signed-off-by: Takahiro Adachi <tadachi@tadachi-net.com>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The firmware is now loaded when the driver is actually used for the first
time. This allows the driver to be compiled in-kernel instead of as a module.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up duplicate includes in
drivers/media/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add the ivtv-fb framebuffer driver for cx23415 devices (currently
only the Hauppauge PVR-350 cards). This makes it possible to use
the On-Screen Display functionality of these cards, either for menus
during MPEG playback, or as a console or X display.
Signed-off-by: Kevin Thayer <nufan_wfk@yahoo.com>
Signed-off-by: Chris Kennedy <c@groovy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: John P Harvey <john.p.harvey@btinternet.com>
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add permissions to all the module parameters so they can be queried and set
(when possible) via sysfs.
Add description for the vidmem parameter.
Change the video_nr parameter to an array, so that the video number can be
specified when a user has more than one card. The driver would try to give
all cards the same number otherwise, which will fail for all cards after the
first.
The default_input option would only allow values of 0 or 1, contrary to the
description. Allow values up to the number of inputs defined for the card.
Add description of lock_norm's different behavior for 1 and >1.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Debugging cleanups to the zr36067 driver:
* Use module_param_named() to declare the debug parameter, so we can
use a single global variable to handle the debug level. This makes
the driver a bit smaller (by 648 bytes on x86_64), thanks to one
less level of indirection on every use.
* Change the debug parameter sysfs permissions, so that the debug
level can be adjusted at runtime, as is done in many other
media/video drivers.
* The debug level is between 0 and 5, not 0 and 4.
* Move the zr_debug export and dprintk macro definition to a header
file so that we don't have to define them in each source file.
* Simplify a duplicate test on zr_debug.
Note that zr_debug was subsequently renamed to debug_zr36067 to avoid
possible conflicts with other Zoran device drivers, on a suggestion
by Trent Piepho.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix a compile warning on non-32-bit machines in v4l2-int-device.h.
Add internal ioctl interface fallback function for ioctls with one
argument.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add a driver for Toshiba TCM825x VGA camera sensor. This sensor is used
e.g. in Nokia N800 internet tablet.
This driver uses the new V4L2 internal ioctl interface.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds an internal ioctl-like interface which can be used in
situations where a single Video4Linux device is implemented by multiple
device drivers. One master device controls one or more slave devices.
The slaves provide Video4Linux ioctl-like interface for the use of the
master.
Only a handful of ioctls are implemented at the moment. More can (and
should) be added as more functionality is required.
Signed-off-by: Sakari Ailus <sakari.ailus@nokia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Using udma yuv causes the driver becomes locked into that mode. This prevents
use of the mpeg decoder & non-udma yuv output. This patch clears the
operating mode when the device is closed.
Signed-off-by: Ian Armstrong <ian@iarmst.demon.co.uk>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
duplicated .mmap in one, .vidioc_s_audio misspelled as .vidioc_g_audio
in other
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a couple drivers that do not correctly terminate their pci_device_id
lists. This results in garbage being spewed into modules.pcimap when the
module happens to not have 28 NULL bytes following the table, and/or the
last PCI ID is actually truncated from the table when calculating the
modules.alias PCI aliases, cause those unfortunate device IDs to not
auto-load.
Signed-off-by: Kees Cook <kees@ubuntu.com>
Acked-by: Corey Minyard <minyard@acm.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Bug: With a hardware encoder board installed as cx88[1] and a
non-encoder boards installed as cx88[0], an OOPS is generated
during cx8802_get_device() called from mpeg_open().
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
saa7191.c: In function 'saa7191_probe':
saa7191.c:596: warning: passing argument 3 of
'saa7191_write_block' discards qualifiers from pointer target type
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Commit 85237f202d introduced the
following warning (with CONFIG_USB_PWC_DEBUG=y):
drivers/media/video/pwc/pwc-if.c: In function "pwc_video_close":
drivers/media/video/pwc/pwc-if.c:1211: warning: "i" may be used uninitialized in this function
This is true, and can cause a broken debug message to be logged.
Here's a fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Right now the composite sound input doesn't work on AverTV 307 because of
the wrong mux setup. The composite sound is routed via an external
4channel multiplexer controlled by GPIO, while the code assumes an internal
multiplexer instead.
Presumably this was a copy/paste error, and noone have ever tested the
functionality.
With the attached patch it works properly, which gives me an ability to
finally watch the cable TV under linux.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Nickolay V. Shmyrev <nshmyrev@yandex.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Due to a documentation bug (the type mask is 3 bits long, not 2) the wrong
frame types were filled in: the B and P frame types were swapped.
This bug also hid a second bug: when a capture is stopped a last entry is
written into the pgm index buffer with internal type 0, denoting the end
of the program. This entry wasn't ignored, instead it was accidentally
returned to the caller as a P frame.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
the pwc driver has a disconnect method that waits for user space to
close the device. This opens up an opportunity for a DoS attack,
blocking the USB subsystem and making khubd's task busy wait in
kernel space. This patch shifts freeing resources to close if an opened
device is disconnected.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If, in em28xx_usb_probe() the memory allocation
dev->alt_max_pkt_size = kmalloc(32*
dev->num_alt,GFP_KERNEL);
fails, then we'll bail out and return -ENOMEM.
The problem is that in that case we don't free the storage allocated
to 'dev', thus causing a memory leak.
This patch fixes the leak by freeing 'dev' before we return -ENOMEM.
This fixes Coverity bug #647.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Configuring the OLPC camera requires something over 150 register
writes. Unfortunately, querying the CAFE i2c controller too
soon after a write causes the hardware to flake. The problem had
been "solved" with an msleep() call, but, between the number of
registers and how msleep() behaves, that resulted in a 3-second
delay on camera initialization. Instead, we hand-code a wait for
the completion interrupt which avoids reading the status registers.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
ivtv: fix VIDIOC_S_FBUF support: new OSD values where never actually set.
The values set with VIDIOC_S_FBUF were not actually used until the next
VIDIOC_S_FMT. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
While decoding (MPEG or YUV) is active or when VBI output is in use, then
do not clear the VBI output of the saa7127. Only after the last user is
gone can we clear it.
This fixes the case where playback was stopped, another channel was chosen
and playback was restarted, while /dev/vbi16 was used to set the WSS
(widescreen) setting. Without this fix the WSS was reset on every stop
instead of just keeping the last value.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
First try polling for the result of a mailbox command, then
switch to a test/sleep loop. Also reduce the sleep time from 10 ms
to 1 ms. Improves the responsiveness of the mailbox handling.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Pausing a decoder followed by a Play command would do nothing. Fixed.
Pausing a decoder running at non-standard speed following by a Continue
would reset the speed to 100%. Fixed.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
s_register was assigning the return code to (unsigned)reg->val, rather than
errCode, which it what it would return. Except reg->val can't be < 0, so it
would never actually return an error.
g_register never actually put the value it read into reg->val.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Various gpio and mux settings for the Osprey 440 weren't correct. Fix them
and provide some documentation about how the gpios work.
The osprey eeprom routine wasn't run for the 440, add it. It was also crap,
re-written to be better.
Add the Osprey 440 to the Bt878 ALSA driver's whitelist. Currently the sample
rate is fixed at 32kHz, as the driver doesn't support different rates for
digital input mode, though the card can select the rate from 32, 44.1, or 48
kHz via gpio.
Setting the audio gain via ALSA isn't supported yet; a userspace tool that
programs the X9221 via i2c-dev must be used.
The Bt878 digital audio format isn't programmed correctly for the CS5331A ADC
used, resulting in extremely garbled sound. That is fixed in a followup
patch.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
When raw capture was turned off, the current capturing frame (v4l_grab_frame)
wasn't reset to NO_GRAB_ACTIVE. If capture was turned back on, the driver
would think this frame was currently being captured, and wait for it to
complete before starting a new frame. The hardware on the other hand would
not be actively capturing a frame. The result was the driver would wait
forever for v4l_grab_frame to be captured.
Some calls to zr36057_set_memgrab(0) were missing spin-locks, which have been
added.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for the UYVY and the other big endian output formats. The
driver was naming formats based on the host endianess. This is different
that all the other drivers appear to work and not what software appears
to expect.
Use ARRAY_SIZE() to find the the size of the zoran_formats array.
Change the way the driver handles setting the video format register. Rather
than use some if and switch statements to set to register by looking at the
format id, the format list simply has a field with the proper bits to set.
Adds a bit of ifdef to make a driver without V4L1 support more possible.
Also create a macro for defining formats that handles vl41 and/or vl42
support to avoid repeated ifdefs in the format list.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The driver was returning the size of the (fixed) buffer it allocated as the
sizeimage field in the v4l2 pixel format, rather than the actual size of the
image. For example, a 192x128 YUYV image is 49152 bytes but the driver would
always return 131072 bytes since if that was the size of the v4l buffer.
This violates the v4l2 spec, which says that sizeimage should be the actual
size of the image for uncompressed formats. It also caused mplayer to crash.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
During uncompressed capture, the poll() function was looking the wrong frame.
It was using the frame the driver was going to capture into next (pend_tail),
when it should have been looking at the next frame to be de-queued with
DQBUF/SYNC (sync_tail).
It also wasn't looking in the right spot. It was looking at the file handle's
copy of the buffer status, rather than the driver core copy. The interrupt
routine marks frames as done in the driver core copy, the file handle copy
isn't updated. So even if poll() looked at the right frame, it would never
see it transition to done and return POLLIN.
The compressed capture code has this same problem, looking in fh->jpg_buffers
when it should have used zr->jpg_buffers.
There was some logic to detect when there was no current capture in process
nor any frames queued and try to return an error, which ends up being a bad
idea. It's possible to call select() from one thread while no capture is in
process, or no frames queued, and then start a capture or queue frames from
another thread.
The buffer state variables are protected by a spin lock, which the code wasn't
acquiring. That is fixed too.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The zr36067 driver doesn't make a distinction between the different sub-types
of NTSC, PAL, or SECAM norms. For example, when the enum std ioctl returns
the PAL standard it returns PAL_BG|PAL_DK|PAL_H|PAL_I.
When setting the norm, it required the bitmask to match exactly the set of
norms used during the enumeration. If just one norm was specified, for
example PAL_BG or NTSC_M, it would fail. This violates the V4L2 spec,
"VIDIOC_S_STD accepts *one* or more flags..."
The key thing to realize is that V4L2_STD_PAL is not one bit, it is multiple
bits. It's ok to call S_STD with any *one* of those bits, but the driver was
requiring *all* of them.
This fixes the S_STD function so that it will accept any set of one or more
PAL norms as PAL, and the same for NTSC and SECAM.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Acked-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The patch adds checking of kthread_run return code and issues a message
if it fails.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If v4l2_ctrl_next is called without the V4L2_CTRL_FLAG_NEXT_CTRL then it
should check whether the passed control ID is valid and return 0 if it
isn't. Otherwise a for-loop over the control IDs will never end.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The VBI DMA is handled in a special way and is marked with a bit.
However, that bit was set at the wrong time and could be cleared
by mistake if a PCM (or other) DMA request would arrive before the
VBI DMA was completed. So on completion of the VBI DMA the driver
no longer knew that that DMA transfer was for VBI data. And this
in turn caused havoc with the card's DMA engine.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
