Currently, the accelerated receive path for VLAN's will
drop packets if the real device is an inactive slave and
is not one of the special pkts tested for in
skb_bond_should_drop(). This behavior is different then
the non-accelerated path and for pkts over a bonded vlan.
For example,
vlanx -> bond0 -> ethx
will be dropped in the vlan path and not delivered to any
packet handlers at all. However,
bond0 -> vlanx -> ethx
and
bond0 -> ethx
will be delivered to handlers that match the exact dev,
because the VLAN path checks the real_dev which is not a
slave and netif_recv_skb() doesn't drop frames but only
delivers them to exact matches.
This patch adds a sk_buff flag which is used for tagging
skbs that would previously been dropped and allows the
skb to continue to skb_netif_recv(). Here we add
logic to check for the deliver_no_wcard flag and if it
is set only deliver to handlers that match exactly. This
makes both paths above consistent and gives pkt handlers
a way to identify skbs that come from inactive slaves.
Without this patch in some configurations skbs will be
delivered to handlers with exact matches and in others
be dropped out right in the vlan path.
I have tested the following 4 configurations in failover modes
and load balancing modes.
# bond0 -> ethx
# vlanx -> bond0 -> ethx
# bond0 -> vlanx -> ethx
# bond0 -> ethx
|
vlanx -> --
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use low order bit of skb->_skb_dst to tell dst is not refcounted.
Change _skb_dst to _skb_refdst to make sure all uses are catched.
skb_dst() returns the dst, regardless of noref bit set or not, but
with a lockdep check to make sure a noref dst is not given if current
user is not rcu protected.
New skb_dst_set_noref() helper to set an notrefcounted dst on a skb.
(with lockdep check)
skb_dst_drop() drops a reference only if skb dst was refcounted.
skb_dst_force() helper is used to force a refcount on dst, when skb
is queued and not anymore RCU protected.
Use skb_dst_force() in __sk_add_backlog(), __dev_xmit_skb() if
!IFF_XMIT_DST_RELEASE or skb enqueued on qdisc queue, in
sock_queue_rcv_skb(), in __nf_queue().
Use skb_dst_force() in dev_requeue_skb().
Note: dst_use_noref() still dirties dst, we might transform it
later to do one dirtying per jiffies.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() & get_rps_cpus() currently need two 64bytes cache
lines in packet to compute rxhash.
Increasing NET_SKB_PAD from 32 to 64 reduces the need to one cache
line only, and makes RPS faster.
NET_IP_ALIGN(2) + ethernet_header(14) + IP_header(20/40) + ports(8)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With following patch I can reach maximum rate of my pktgen+udpsink
simulator :
- 'old' machine : dual quad core E5450 @3.00GHz
- 64 UDP rx flows (only differ by destination port)
- RPS enabled, NIC interrupts serviced on cpu0
- rps dispatched on 7 other cores. (~130.000 IPI per second)
- SLAB allocator (faster than SLUB in this workload)
- tg3 NIC
- 1.080.000 pps without a single drop at NIC level.
Idea is to add two prefetchw() calls in __alloc_skb(), one to prefetch
first sk_buff cache line, the second to prefetch the shinfo part.
Also using one memset() to initialize all skb_shared_info fields instead
of one by one to reduce number of instructions, using long word moves.
All skb_shared_info fields before 'dataref' are cleared in
__alloc_skb().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 6be8ac2f ("[NET]: uninline skb_pull, de-bloats a lot")
we uninlined skb_pull.
But in some critical paths it makes sense to inline this thing
and it helps performance significantly.
Create an skb_pull_inline() so that we can do this in a way that
serves also as annotation.
Based upon a patch by Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no need to export skb_under_panic() and skb_over_panic() in
skbuff.c, since these methods are used only in skbuff.c ; this patch
removes these two exports. It also marks these functions as 'static'
and removeS the extern declarations of them from
include/linux/skbuff.h
Signed-off-by: Rami Rosen <ramirose@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
dev_consume_skb and kfree_skb_clean have no users and in the case of
kfree_skb_clean could cause potential build issues since I cannot find
where it is defined. Based on the patch in which it was introduced it
appears to have been a bit of leftover code from an earlier version of the
patch in which kfree_skb_clean was dropped in favor of consume_skb.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The dma map fields in the skb_shared_info structure no longer has any users
and can be dropped since it is making the skb_shared_info unecessarily larger.
Running slabtop show that we were using 4K slabs for the skb->head on x86_64 w/
an allocation size of 1522. It turns out that the dma_head and dma_maps array
made skb_shared large enough that we had crossed over the 2k boundary with
standard frames and as such we were using 4k blocks of memory for all skbs.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements software receive side packet steering (RPS). RPS
distributes the load of received packet processing across multiple CPUs.
Problem statement: Protocol processing done in the NAPI context for received
packets is serialized per device queue and becomes a bottleneck under high
packet load. This substantially limits pps that can be achieved on a single
queue NIC and provides no scaling with multiple cores.
This solution queues packets early on in the receive path on the backlog queues
of other CPUs. This allows protocol processing (e.g. IP and TCP) to be
performed on packets in parallel. For each device (or each receive queue in
a multi-queue device) a mask of CPUs is set to indicate the CPUs that can
process packets. A CPU is selected on a per packet basis by hashing contents
of the packet header (e.g. the TCP or UDP 4-tuple) and using the result to index
into the CPU mask. The IPI mechanism is used to raise networking receive
softirqs between CPUs. This effectively emulates in software what a multi-queue
NIC can provide, but is generic requiring no device support.
Many devices now provide a hash over the 4-tuple on a per packet basis
(e.g. the Toeplitz hash). This patch allow drivers to set the HW reported hash
in an skb field, and that value in turn is used to index into the RPS maps.
Using the HW generated hash can avoid cache misses on the packet when
steering it to a remote CPU.
The CPU mask is set on a per device and per queue basis in the sysfs variable
/sys/class/net/<device>/queues/rx-<n>/rps_cpus. This is a set of canonical
bit maps for receive queues in the device (numbered by <n>). If a device
does not support multi-queue, a single variable is used for the device (rx-0).
Generally, we have found this technique increases pps capabilities of a single
queue device with good CPU utilization. Optimal settings for the CPU mask
seem to depend on architectures and cache hierarcy. Below are some results
running 500 instances of netperf TCP_RR test with 1 byte req. and resp.
Results show cumulative transaction rate and system CPU utilization.
e1000e on 8 core Intel
Without RPS: 108K tps at 33% CPU
With RPS: 311K tps at 64% CPU
forcedeth on 16 core AMD
Without RPS: 156K tps at 15% CPU
With RPS: 404K tps at 49% CPU
bnx2x on 16 core AMD
Without RPS 567K tps at 61% CPU (4 HW RX queues)
Without RPS 738K tps at 96% CPU (8 HW RX queues)
With RPS: 854K tps at 76% CPU (4 HW RX queues)
Caveats:
- The benefits of this patch are dependent on architecture and cache hierarchy.
Tuning the masks to get best performance is probably necessary.
- This patch adds overhead in the path for processing a single packet. In
a lightly loaded server this overhead may eliminate the advantages of
increased parallelism, and possibly cause some relative performance degradation.
We have found that masks that are cache aware (share same caches with
the interrupting CPU) mitigate much of this.
- The RPS masks can be changed dynamically, however whenever the mask is changed
this introduces the possibility of generating out of order packets. It's
probably best not change the masks too frequently.
Signed-off-by: Tom Herbert <therbert@google.com>
include/linux/netdevice.h | 32 ++++-
include/linux/skbuff.h | 3 +
net/core/dev.c | 335 +++++++++++++++++++++++++++++++++++++--------
net/core/net-sysfs.c | 225 ++++++++++++++++++++++++++++++-
net/core/skbuff.c | 2 +
5 files changed, 538 insertions(+), 59 deletions(-)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e992cd9b72 (kmemcheck: make bitfield annotations truly no-ops
when disabled) allows us to revert a workaround we did in the past to
not add holes in sk_buff structure.
This patch partially reverts commit 14d18a81b5
(net: fix kmemcheck annotations) so that sparse doesnt complain:
include/linux/skbuff.h:357:41: error: invalid bitfield specifier for
type restricted __be16.
Reported-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The alignment requirement for 64-bit load/store instructions on ARM is
implementation defined. Some CPUs (such as Marvell Feroceon) do not
generate an exception, if such an instruction is executed with an
address that is not 64 bit aligned. In such a case, the Feroceon
corrupts adjacent memory, which showed up in my tests as a crash in the
rx path of ath9k that only occured with CONFIG_XFRM set.
This crash happened, because the first field of the mac80211 rx status
info in the cb is an u64, and changing it corrupted the skb->sp field.
This patch also closes some potential pre-existing holes in the sk_buff
struct surrounding the cb[] area.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
The function name must be followed by a space, hypen, space, and a
short description.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
The two functions skb_dma_map/unmap are unsafe to use as they cause
problems when packets are cloned and sent to multiple devices while a HW
IOMMU is enabled. Due to this it is best to remove the code so it is not
used by any other network driver maintainters.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/usb/cdc_ether.c
All CDC ethernet devices of type USB_CLASS_COMM need to use
'&mbm_info'.
Signed-off-by: David S. Miller <davem@davemloft.net>
This cleanup patch puts struct/union/enum opening braces,
in first line to ease grep games.
struct something
{
becomes :
struct something {
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On UDP sockets, we must call skb_free_datagram() with socket locked,
or risk sk_forward_alloc corruption. This requirement is not respected
in SUNRPC.
Add a convenient helper, skb_free_datagram_locked() and use it in SUNRPC
Reported-by: Francis Moreau <francis.moro@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sk_buff kmemcheck annotations enlarged this structure by 8/16 bytes
Fix this by moving 'protocol' inside flags1 bitfield,
and queue_mapping inside flags2 bitfield.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of hardcoding NET_IP_ALIGN stuff in various network drivers,
we can add a helper around netdev_alloc_skb()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a new socket level option to report number of queue overflows
Recently I augmented the AF_PACKET protocol to report the number of frames lost
on the socket receive queue between any two enqueued frames. This value was
exported via a SOL_PACKET level cmsg. AFter I completed that work it was
requested that this feature be generalized so that any datagram oriented socket
could make use of this option. As such I've created this patch, It creates a
new SOL_SOCKET level option called SO_RXQ_OVFL, which when enabled exports a
SOL_SOCKET level cmsg that reports the nubmer of times the sk_receive_queue
overflowed between any two given frames. It also augments the AF_PACKET
protocol to take advantage of this new feature (as it previously did not touch
sk->sk_drops, which this patch uses to record the overflow count). Tested
successfully by me.
Notes:
1) Unlike my previous patch, this patch simply records the sk_drops value, which
is not a number of drops between packets, but rather a total number of drops.
Deltas must be computed in user space.
2) While this patch currently works with datagram oriented protocols, it will
also be accepted by non-datagram oriented protocols. I'm not sure if thats
agreeable to everyone, but my argument in favor of doing so is that, for those
protocols which aren't applicable to this option, sk_drops will always be zero,
and reporting no drops on a receive queue that isn't used for those
non-participating protocols seems reasonable to me. This also saves us having
to code in a per-protocol opt in mechanism.
3) This applies cleanly to net-next assuming that commit
977750076d (my af packet cmsg patch) is reverted
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mac80211 required this due to the master netdev, but now
it can put all information into skb->cb and this can go.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the correct function call for skb_reserve in the comment for
NET_IP_ALIGN.
Signed-off-by: Tobias Klauser <klto@zhaw.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (55 commits)
netxen: fix tx ring accounting
netxen: fix detection of cut-thru firmware mode
forcedeth: fix dma api mismatches
atm: sk_wmem_alloc initial value is one
net: correct off-by-one write allocations reports
via-velocity : fix no link detection on boot
Net / e100: Fix suspend of devices that cannot be power managed
TI DaVinci EMAC : Fix rmmod error
net: group address list and its count
ipv4: Fix fib_trie rebalancing, part 2
pkt_sched: Update drops stats in act_police
sky2: version 1.23
sky2: add GRO support
sky2: skb recycling
sky2: reduce default transmit ring
sky2: receive counter update
sky2: fix shutdown synchronization
sky2: PCI irq issues
sky2: more receive shutdown
sky2: turn off pause during shutdown
...
Manually fix trivial conflict in net/core/skbuff.c due to kmemcheck
Fix kernel-doc warnings (missing + extra entries) in skbuff.h.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to handle powersave frames properly we had needed
to pass these out to the device queues again, and introduce
the skb->requeue bit. This, however, also has unnecessary
overhead by needing to 'clean up' already tried frames, and
this clean-up code is also buggy when software encryption
is used.
Instead of sending the frames via the master netdev queue
again, simply put them into the pending queue. This also
fixes a problem where frames for that particular station
could be reordered when some were still on the software
queues and older ones are re-injected into the software
queue after them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With the hope that these can be used to eliminate direct
references to the frag list implementation.
Signed-off-by: David S. Miller <davem@davemloft.net>
skb_dma_unmap() is quite expensive for small packets,
because we use two different cache lines from skb_shared_info.
One to access nr_frags, one to access dma_maps[0]
Instead of dma_maps being an array of MAX_SKB_FRAGS + 1 elements,
let dma_head alone in a new dma_head field, close to nr_frags,
to reduce cache lines misses.
Tested on my dev machine (bnx2 & tg3 adapters), nice speedup !
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of num_dma_maps in struct skb_shared_info, as it seems unused.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Can remove anonymous union now it has one field.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define three accessors to get/set dst attached to a skb
struct dst_entry *skb_dst(const struct sk_buff *skb)
void skb_dst_set(struct sk_buff *skb, struct dst_entry *dst)
void skb_dst_drop(struct sk_buff *skb)
This one should replace occurrences of :
dst_release(skb->dst)
skb->dst = NULL;
Delete skb->dst field
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define skb_rtable(const struct sk_buff *skb) accessor to get rtable from skb
Delete skb->rtable field
Setting rtable is not allowed, just set dst instead as rtable is an alias.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
struct sk_buff uses one union to define dst and rtable fields.
We want to replace direct access to these pointers by accessors.
First patch adds a new "unsigned long _skb_dst;" opaque field
in this union.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New packet socket feature that makes packet socket more efficient for
transmission.
- It reduces number of system call through a PACKET_TX_RING mechanism,
based on PACKET_RX_RING (Circular buffer allocated in kernel space
which is mmapped from user space).
- It minimizes CPU copy using fragmented SKB (almost zero copy).
Signed-off-by: Johann Baudy <johann.baudy@gnu-log.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
aio_write gets const struct iovec * but tun_chr_aio_write casts this to struct
iovec * and modifies the iovec. As a result, attempts to use io_submit
to send packets to a tun device fail with weird errors such as EINVAL.
Since tun is the only user of skb_copy_datagram_from_iovec, we can
fix this simply by changing the later so that it does not
touch the iovec passed to it.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There's an skb_copy_datagram_iovec() to copy out of a paged skb,
but it modifies the iovec, and does not support starting
at an offset in the destination. We want both in tun.c, so let's
add the function.
It's a carbon copy of skb_copy_datagram_iovec() with enough changes to
be annoying.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add missing struct field to fix kernel-doc warning:
Warning(include/linux/skbuff.h:182): No description found for parameter 'flags'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some minor changes to queue hashing:
1. Use const on accessor functions
2. Export skb_tx_hash for use in drivers (see ixgbe)
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define feature flags for FCoE offloads.
Signed-off-by: Chris Leech <christopher.leech@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Fix skbuff.h kernel-doc for timestamps: must include "struct" keyword,
otherwise there are kernel-doc errors:
Error(linux-next-20090227//include/linux/skbuff.h:161): cannot understand prototype: 'struct skb_shared_hwtstamps '
Error(linux-next-20090227//include/linux/skbuff.h:177): cannot understand prototype: 'union skb_shared_tx '
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A long time ago we had bugs, primarily in TCP, where we would modify
skb->truesize (for TSO queue collapsing) in ways which would corrupt
the socket memory accounting.
skb_truesize_check() was added in order to try and catch this error
more systematically.
However this debugging check has morphed into a Frankenstein of sorts
and these days it does nothing other than catch false-positives.
Signed-off-by: David S. Miller <davem@davemloft.net>
The additional per-packet information (16 bytes for time stamps, 1
byte for flags) is stored for all packets in the skb_shared_info
struct. This implementation detail is hidden from users of that
information via skb_* accessor functions. A separate struct resp.
union is used for the additional information so that it can be
stored/copied easily outside of skb_shared_info.
Compared to previous implementations (reusing the tstamp field
depending on the context, optional additional structures) this
is the simplest solution. It does not extend sk_buff itself.
TX time stamping is implemented in software if the device driver
doesn't support hardware time stamping.
The new semantic for hardware/software time stamping around
ndo_start_xmit() is based on two assumptions about existing
network device drivers which don't support hardware time
stamping and know nothing about it:
- they leave the new skb_shared_tx unmodified
- the keep the connection to the originating socket in skb->sk
alive, i.e., don't call skb_orphan()
Given that skb_shared_tx is new, the first assumption is safe.
The second is only true for some drivers. As a result, software
TX time stamping currently works with the bnx2 driver, but not
with the unmodified igb driver (the two drivers this patch series
was tested with).
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This kills of HAVE_ALLOC_SKB and HAVE_ALIGNABLE_SKB.
Nothing in-tree uses them and nothing in-tree has used them
since 2.0.x times.
Signed-off-by: David S. Miller <davem@davemloft.net>
