Pull trivial tree updates from Jiri Kosina:
"The usual stuff from trivial tree"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
treewide: relase -> release
Documentation/cgroups/memory.txt: fix stat file documentation
sysctl/net.txt: delete reference to obsolete 2.4.x kernel
spinlock_api_smp.h: fix preprocessor comments
treewide: Fix typo in printk
doc: device tree: clarify stuff in usage-model.txt.
open firmware: "/aliasas" -> "/aliases"
md: bcache: Fixed a typo with the word 'arithmetic'
irq/generic-chip: fix a few kernel-doc entries
frv: Convert use of typedef ctl_table to struct ctl_table
sgi: xpc: Convert use of typedef ctl_table to struct ctl_table
doc: clk: Fix incorrect wording
Documentation/arm/IXP4xx fix a typo
Documentation/networking/ieee802154 fix a typo
Documentation/DocBook/media/v4l fix a typo
Documentation/video4linux/si476x.txt fix a typo
Documentation/virtual/kvm/api.txt fix a typo
Documentation/early-userspace/README fix a typo
Documentation/video4linux/soc-camera.txt fix a typo
lguest: fix CONFIG_PAE -> CONFIG_x86_PAE in comment
...
The recent comment:
commit 7e83ccbecd
md/raid10: Allow skipping recovery when clean arrays are assembled
Causes raid10 to skip a recovery in certain cases where it is safe to
do so. Unfortunately it also causes a reshape to be skipped which is
never safe. The result is that an attempt to reshape a RAID10 will
appear to complete instantly, but no data will have been moves so the
array will now contain garbage.
(If nothing is written, you can recovery by simple performing the
reverse reshape which will also complete instantly).
Bug was introduced in 3.10, so this is suitable for 3.10-stable.
Cc: stable@vger.kernel.org (3.10)
Cc: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
There is a bug in 'check_reshape' for raid5.c To checks
that the new minimum number of devices is large enough (which is
good), but it does so also after the reshape has started (bad).
This is bad because
- the calculation is now wrong as mddev->raid_disks has changed
already, and
- it is pointless because it is now too late to stop.
So only perform that test when reshape has not been committed to.
Signed-off-by: NeilBrown <neilb@suse.de>
1/ If a RAID10 is being reshaped to a fewer number of devices
and is stopped while this is ongoing, then when the array is
reassembled the 'mirrors' array will be allocated too small.
This will lead to an access error or memory corruption.
2/ A sanity test for a reshaping RAID10 array is restarted
is slightly incorrect.
Due to the first bug, this is suitable for any -stable
kernel since 3.5 where this code was introduced.
Cc: stable@vger.kernel.org (v3.5+)
Signed-off-by: NeilBrown <neilb@suse.de>
MD: Remember the last sync operation that was performed
This patch adds a field to the mddev structure to track the last
sync operation that was performed. This is especially useful when
it comes to what is recorded in mismatch_cnt in sysfs. If the
last operation was "data-check", then it reports the number of
descrepancies found by the user-initiated check. If it was a
"repair" operation, then it is reporting the number of
descrepancies repaired. etc.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
RAID5 uses a 'per-array' value for the 'size' of each device.
RAID0 uses a 'per-device' value - it can be different for each device.
When converting a RAID5 to a RAID0 we must ensure that the per-device
size of each device matches the per-array size for the RAID5, else
the array will change size.
If the metadata cannot record a changed per-device size (as is the
case with v0.90 metadata) the array could get bigger on restart. This
does not cause data corruption, so it not a big issue and is mainly
yet another a reason to not use 0.90.
Signed-off-by: NeilBrown <neilb@suse.de>
It isn't really enough to check that the rdev is present, we need to
also be sure that the device is still In_sync.
Doing this requires using rcu_dereference to access the rdev, and
holding the rcu_read_lock() to ensure the rdev doesn't disappear while
we look at it.
Signed-off-by: NeilBrown <neilb@suse.de>
As 'enough' accesses conf->prev and conf->geo, which can change
spontanously, it should guard against changes.
This can be done with device_lock as start_reshape holds device_lock
while updating 'geo' and end_reshape holds it while updating 'prev'.
So 'error' needs to hold 'device_lock'.
On the other hand, raid10_end_read_request knows which of the two it
really wants to access, and as it is an active request on that one,
the value cannot change underneath it.
So change _enough to take flag rather than a pointer, pass the
appropriate flag from raid10_end_read_request(), and remove the locking.
All other calls to 'enough' are made with reconfig_mutex held, so
neither 'prev' nor 'geo' can change.
Signed-off-by: NeilBrown <neilb@suse.de>
The usage of strict_strtoul() is not preferred, because
strict_strtoul() is obsolete. Thus, kstrtoul() should be
used.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When a device has failed, it needs to be removed from the personality
module before it can be removed from the array as a whole.
The first step is performed by md_check_recovery() which is called
from the raid management thread.
So when a HOT_REMOVE ioctl arrives, wait briefly for md_check_recovery
to have run. This increases the chance that the ioctl will succeed.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Neil Brown <nfbrown@suse.de>
This doesn't really need to be initialised, but it doesn't hurt,
silences the compiler, and as it is a counter it makes sense for it to
start at zero.
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Fix raid_resume not reviving failed devices in all cases
When a device fails in a RAID array, it is marked as Faulty. Later,
md_check_recovery is called which (through the call chain) calls
'hot_remove_disk' in order to have the personalities remove the device
from use in the array.
Sometimes, it is possible for the array to be suspended before the
personalities get their chance to perform 'hot_remove_disk'. This is
normally not an issue. If the array is deactivated, then the failed
device will be noticed when the array is reinstantiated. If the
array is resumed and the disk is still missing, md_check_recovery will
be called upon resume and 'hot_remove_disk' will be called at that
time. However, (for dm-raid) if the device has been restored,
a resume on the array would cause it to attempt to revive the device
by calling 'hot_add_disk'. If 'hot_remove_disk' had not been called,
a situation is then created where the device is thought to concurrently
be the replacement and the device to be replaced. Thus, the device
is first sync'ed with the rest of the array (because it is the replacement
device) and then marked Faulty and removed from the array (because
it is also the device being replaced).
The solution is to check and see if the device had properly been removed
before the array was suspended. This is done by seeing whether the
device's 'raid_disk' field is -1 - a condition that implies that
'md_check_recovery -> remove_and_add_spares (where raid_disk is set to -1)
-> hot_remove_disk' has been called. If 'raid_disk' is not -1, then
'hot_remove_disk' must be called to complete the removal of the previously
faulty device before it can be revived via 'hot_add_disk'.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Break-up untidy function
Clean-up excessive indentation by moving some code in raid_resume()
into its own function.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add ability to restore transiently failed devices on resume
This patch adds code to the resume function to check over the devices
in the RAID array. If any are found to be marked as failed and their
superblocks can be read, an attempt is made to reintegrate them into
the array. This allows the user to refresh the array with a simple
suspend and resume of the array - rather than having to load a
completely new table, allocate and initialize all the structures and
throw away the old instantiation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some tagged for -stable.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8iy3
-----END PGP SIGNATURE-----
Merge tag 'md-3.10-fixes' of git://neil.brown.name/md
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Cc: stable@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits
050b66152f (raid10) and 6b740b8d79 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
__md_stop_writes() will currently sometimes freeze recovery.
So any caller must be ready for that to happen, and indeed they are.
However if __md_stop_writes() doesn't freeze_recovery, then
a recovery could start before mddev_suspend() is called, which
could be awkward. This can particularly cause problems or dm-raid.
So change __md_stop_writes() to always freeze recovery. This is safe
and more predicatable.
Reported-by: Brassow Jonathan <jbrassow@redhat.com>
Tested-by: Brassow Jonathan <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block layer fixes from Jens Axboe:
"Outside of bcache (which really isn't super big), these are all
few-liners. There are a few important fixes in here:
- Fix blk pm sleeping when holding the queue lock
- A small collection of bcache fixes that have been done and tested
since bcache was included in this merge window.
- A fix for a raid5 regression introduced with the bio changes.
- Two important fixes for mtip32xx, fixing an oops and potential data
corruption (or hang) due to wrong bio iteration on stacked devices."
* 'for-linus' of git://git.kernel.dk/linux-block:
scatterlist: sg_set_buf() argument must be in linear mapping
raid5: Initialize bi_vcnt
pktcdvd: silence static checker warning
block: remove refs to XD disks from documentation
blkpm: avoid sleep when holding queue lock
mtip32xx: Correctly handle bio->bi_idx != 0 conditions
mtip32xx: Fix NULL pointer dereference during module unload
bcache: Fix error handling in init code
bcache: clarify free/available/unused space
bcache: drop "select CLOSURES"
bcache: Fix incompatible pointer type warning
The patch that converted raid5 to use bio_reset() forgot to initialize
bi_vcnt.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Cc: NeilBrown <neilb@suse.de>
Cc: linux-raid@vger.kernel.org
Tested-by: Ilia Mirkin <imirkin@alum.mit.edu>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Fix detection of the need to resize the dm thin metadata device.
The code incorrectly tried to extend the metadata device when it
didn't need to due to a merging error with patch 24347e9 ("dm thin:
detect metadata device resizing").
device-mapper: transaction manager: couldn't open metadata space map
device-mapper: thin metadata: tm_open_with_sm failed
device-mapper: thin: aborting transaction failed
device-mapper: thin: switching pool to failure mode
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The Kconfig entry for BCACHE selects CLOSURES. But there's no Kconfig
symbol CLOSURES. That symbol was used in development versions of bcache,
but was removed when the closures code was no longer provided as a
kernel library. It can safely be dropped.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
The function pointer release in struct block_device_operations
should point to functions declared as void.
Sparse warnings:
drivers/md/bcache/super.c:656:27: warning:
incorrect type in initializer (different base types)
drivers/md/bcache/super.c:656:27:
expected void ( *release )( ... )
drivers/md/bcache/super.c:656:27:
got int ( static [toplevel] *<noident> )( ... )
drivers/md/bcache/super.c:656:2: warning:
initialization from incompatible pointer type [enabled by default]
drivers/md/bcache/super.c:656:2: warning:
(near initialization for ‘bcache_ops.release’) [enabled by default]
Signed-off-by: Emil Goode <emilgoode@gmail.com>
Signed-off-by: Kent Overstreet <koverstreet@google.com>
Share configuration option processing code between the dm cache
ctr and message functions.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Generate a dm event when the amount of remaining thin pool metadata
space falls below a certain level.
The threshold is taken to be a quarter of the size of the metadata
device with a minimum threshold of 4MB.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a threshold callback to dm persistent data space maps.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a threshold callback function to the persistent data space map
interface for a subsequent patch to use.
dm-thin and dm-cache are interested in knowing when they're getting
low on metadata or data blocks. This patch introduces a new method
for registering a callback against a threshold.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow the dm thin pool metadata device to be extended.
Whenever a pool is resumed, detect whether the size of the metadata
device has increased, and if so, extend the metadata to use the new
space.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support extending a dm persistent data metadata space map.
The extend itself is implemented by switching back to the boostrap
allocator and pointing to the new space. The extra bitmap indexes are
then allocated from the new space, and finally we switch back to the
proper space map ops and tweak the reference counts.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If a thin pool is created in read-only-metadata mode then only open the
metadata device read-only.
Previously it was always opened with FMODE_READ | FMODE_WRITE.
(Note that dm_get_device() still allows read-only dm devices to be used
read-write at the moment: If I create a read-only linear device for the
metadata, via dmsetup load --readonly, then I can still create a rw pool
out of it.)
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Refactor device size functions in preparation for similar metadata
device resizing functions.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Correct the documented requirement on the return code from dm cache policy
lookup functions stated in the policy module header file.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix some typos in dm-space-map-metadata.c error messages.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Tune the dm cache migration throttling.
i) Issue a tick every second, just in case there's no i/o going through.
ii) Drop the migration threshold right down to something suitable for
background work.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Enable WRITE SAME support in dm multipath. As far as multipath is
concerned it is just another write request.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Bharata B Rao <bharata.rao@gmail.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If device_not_write_same_capable() returns true then the iterate_devices
loop in dm_table_supports_write_same() should return false.
Reported-by: Bharata B Rao <bharata.rao@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # v3.8+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch uses memalloc_noio_save to avoid a possible deadlock in
dm-bufio. (it could happen only with large block size, at most
PAGE_SIZE << MAX_ORDER (typically 8MiB).
__vmalloc doesn't fully respect gfp flags. The specified gfp flags are
used for allocation of requested pages, structures vmap_area, vmap_block
and vm_struct and the radix tree nodes.
However, the kernel pagetables are allocated always with GFP_KERNEL.
Thus the allocation of pagetables can recurse back to the I/O layer and
cause a deadlock.
This patch uses the function memalloc_noio_save to set per-process
PF_MEMALLOC_NOIO flag and the function memalloc_noio_restore to restore
it. When this flag is set, all allocations in the process are done with
implied GFP_NOIO flag, thus the deadlock can't happen.
This should be backported to stable kernels, but they don't have the
PF_MEMALLOC_NOIO flag and memalloc_noio_save/memalloc_noio_restore
functions. So, PF_MEMALLOC should be set and restored instead.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Return -ENOMEM instead of success if unable to allocate pending
exception mempool in snapshot_ctr.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix a regression in the calculation of the stripe_width in the
dm stripe target which led to incorrect processing of device limits.
The stripe_width is the stripe device length divided by the number of
stripes. The group of commits in the range f14fa69 ("dm stripe: fix
size test") to eb850de ("dm stripe: support for non power of 2
chunksize") interfered with each other (a merging error) and led to the
stripe_width being set incorrectly to the stripe device length divided by
chunk_size * stripe_count.
For example, a stripe device's table with: 0 33553920 striped 3 512 ...
should result in a stripe_width of 11184640 (33553920 / 3), but due to
the bug it was getting set to 21845 (33553920 / (512 * 3)).
The impact of this bug is that device topologies that previously worked
fine with the stripe target are no longer considered valid. In
particular, there is a higher risk of seeing this issue if one of the
stripe devices has a 4K logical block size. Resulting in an error
message like this:
"device-mapper: table: 253:4: len=21845 not aligned to h/w logical block size 4096 of dm-1"
The fix is to swap the order of the divisions and to use a temporary
variable for the second one, so that width retains the intended
value.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.6+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Pull block driver updates from Jens Axboe:
"It might look big in volume, but when categorized, not a lot of
drivers are touched. The pull request contains:
- mtip32xx fixes from Micron.
- A slew of drbd updates, this time in a nicer series.
- bcache, a flash/ssd caching framework from Kent.
- Fixes for cciss"
* 'for-3.10/drivers' of git://git.kernel.dk/linux-block: (66 commits)
bcache: Use bd_link_disk_holder()
bcache: Allocator cleanup/fixes
cciss: bug fix to prevent cciss from loading in kdump crash kernel
cciss: add cciss_allow_hpsa module parameter
drivers/block/mg_disk.c: add CONFIG_PM_SLEEP to suspend/resume functions
mtip32xx: Workaround for unaligned writes
bcache: Make sure blocksize isn't smaller than device blocksize
bcache: Fix merge_bvec_fn usage for when it modifies the bvm
bcache: Correctly check against BIO_MAX_PAGES
bcache: Hack around stuff that clones up to bi_max_vecs
bcache: Set ra_pages based on backing device's ra_pages
bcache: Take data offset from the bdev superblock.
mtip32xx: mtip32xx: Disable TRIM support
mtip32xx: fix a smatch warning
bcache: Disable broken btree fuzz tester
bcache: Fix a format string overflow
bcache: Fix a minor memory leak on device teardown
bcache: Documentation updates
bcache: Use WARN_ONCE() instead of __WARN()
bcache: Add missing #include <linux/prefetch.h>
...
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
The value passed is 0 in all but "it can never happen" cases (and those
only in a couple of drivers) *and* it would've been lost on the way
out anyway, even if something tried to pass something meaningful.
Just don't bother.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
