remove the mg_disk driver

This drivers was added in 2008, but as far as a I can tell we never had a
single platform that actually registered resources for the platform driver.

It's also been unmaintained for a long time and apparently has a ATA mode
that can be driven using the IDE/libata subsystem.

Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
This commit is contained in:
Christoph Hellwig 2017-04-06 13:28:46 +02:00 committed by Jens Axboe
parent 3f19cd23f3
commit 8425339492
5 changed files with 0 additions and 1257 deletions

View File

@ -1,84 +0,0 @@
This document describes m[g]flash support in linux.
Contents
1. Overview
2. Reserved area configuration
3. Example of mflash platform driver registration
1. Overview
Mflash and gflash are embedded flash drive. The only difference is mflash is
MCP(Multi Chip Package) device. These two device operate exactly same way.
So the rest mflash repersents mflash and gflash altogether.
Internally, mflash has nand flash and other hardware logics and supports
2 different operation (ATA, IO) modes. ATA mode doesn't need any new
driver and currently works well under standard IDE subsystem. Actually it's
one chip SSD. IO mode is ATA-like custom mode for the host that doesn't have
IDE interface.
Following are brief descriptions about IO mode.
A. IO mode based on ATA protocol and uses some custom command. (read confirm,
write confirm)
B. IO mode uses SRAM bus interface.
C. IO mode supports 4kB boot area, so host can boot from mflash.
2. Reserved area configuration
If host boot from mflash, usually needs raw area for boot loader image. All of
the mflash's block device operation will be taken this value as start offset.
Note that boot loader's size of reserved area and kernel configuration value
must be same.
3. Example of mflash platform driver registration
Working mflash is very straight forward. Adding platform device stuff to board
configuration file is all. Here is some pseudo example.
static struct mg_drv_data mflash_drv_data = {
/* If you want to polling driver set to 1 */
.use_polling = 0,
/* device attribution */
.dev_attr = MG_BOOT_DEV
};
static struct resource mg_mflash_rsc[] = {
/* Base address of mflash */
[0] = {
.start = 0x08000000,
.end = 0x08000000 + SZ_64K - 1,
.flags = IORESOURCE_MEM
},
/* mflash interrupt pin */
[1] = {
.start = IRQ_GPIO(84),
.end = IRQ_GPIO(84),
.flags = IORESOURCE_IRQ
},
/* mflash reset pin */
[2] = {
.start = 43,
.end = 43,
.name = MG_RST_PIN,
.flags = IORESOURCE_IO
},
/* mflash reset-out pin
* If you use mflash as storage device (i.e. other than MG_BOOT_DEV),
* should assign this */
[3] = {
.start = 51,
.end = 51,
.name = MG_RSTOUT_PIN,
.flags = IORESOURCE_IO
}
};
static struct platform_device mflash_dev = {
.name = MG_DEV_NAME,
.id = -1,
.dev = {
.platform_data = &mflash_drv_data,
},
.num_resources = ARRAY_SIZE(mg_mflash_rsc),
.resource = mg_mflash_rsc
};
platform_device_register(&mflash_dev);

View File

@ -434,23 +434,6 @@ config ATA_OVER_ETH
This driver provides Support for ATA over Ethernet block
devices like the Coraid EtherDrive (R) Storage Blade.
config MG_DISK
tristate "mGine mflash, gflash support"
depends on ARM && GPIOLIB
help
mGine mFlash(gFlash) block device driver
config MG_DISK_RES
int "Size of reserved area before MBR"
depends on MG_DISK
default 0
help
Define size of reserved area that usually used for boot. Unit is KB.
All of the block device operation will be taken this value as start
offset
Examples:
1024 => 1 MB
config SUNVDC
tristate "Sun Virtual Disk Client support"
depends on SUN_LDOMS

View File

@ -19,7 +19,6 @@ obj-$(CONFIG_BLK_CPQ_CISS_DA) += cciss.o
obj-$(CONFIG_BLK_DEV_DAC960) += DAC960.o
obj-$(CONFIG_XILINX_SYSACE) += xsysace.o
obj-$(CONFIG_CDROM_PKTCDVD) += pktcdvd.o
obj-$(CONFIG_MG_DISK) += mg_disk.o
obj-$(CONFIG_SUNVDC) += sunvdc.o
obj-$(CONFIG_BLK_DEV_SKD) += skd.o
obj-$(CONFIG_BLK_DEV_OSD) += osdblk.o

File diff suppressed because it is too large Load Diff

View File

@ -1,45 +0,0 @@
/*
* include/linux/mg_disk.c
*
* Private data for mflash platform driver
*
* (c) 2008 mGine Co.,LTD
* (c) 2008 unsik Kim <donari75@gmail.com>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#ifndef __MG_DISK_H__
#define __MG_DISK_H__
/* name for platform device */
#define MG_DEV_NAME "mg_disk"
/* names of GPIO resource */
#define MG_RST_PIN "mg_rst"
/* except MG_BOOT_DEV, reset-out pin should be assigned */
#define MG_RSTOUT_PIN "mg_rstout"
/* device attribution */
/* use mflash as boot device */
#define MG_BOOT_DEV (1 << 0)
/* use mflash as storage device */
#define MG_STORAGE_DEV (1 << 1)
/* same as MG_STORAGE_DEV, but bootloader already done reset sequence */
#define MG_STORAGE_DEV_SKIP_RST (1 << 2)
/* private driver data */
struct mg_drv_data {
/* disk resource */
u32 use_polling;
/* device attribution */
u32 dev_attr;
/* internally used */
void *host;
};
#endif