kernel-ark/drivers/misc/bmp085.c

479 lines
13 KiB
C
Raw Normal View History

drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
/* Copyright (c) 2010 Christoph Mair <christoph.mair@gmail.com>
* Copyright (c) 2012 Bosch Sensortec GmbH
* Copyright (c) 2012 Unixphere AB
*
* This driver supports the bmp085 and bmp18x digital barometric pressure
* and temperature sensors from Bosch Sensortec. The datasheets
* are available from their website:
* http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP085-DS000-05.pdf
* http://www.bosch-sensortec.com/content/language1/downloads/BST-BMP180-DS000-07.pdf
*
* A pressure measurement is issued by reading from pressure0_input.
* The return value ranges from 30000 to 110000 pascal with a resulution
* of 1 pascal (0.01 millibar) which enables measurements from 9000m above
* to 500m below sea level.
*
* The temperature can be read from temp0_input. Values range from
* -400 to 850 representing the ambient temperature in degree celsius
* multiplied by 10.The resolution is 0.1 celsius.
*
* Because ambient pressure is temperature dependent, a temperature
* measurement will be executed automatically even if the user is reading
* from pressure0_input. This happens if the last temperature measurement
* has been executed more then one second ago.
*
* To decrease RMS noise from pressure measurements, the bmp085 can
* autonomously calculate the average of up to eight samples. This is
* set up by writing to the oversampling sysfs file. Accepted values
* are 0, 1, 2 and 3. 2^x when x is the value written to this file
* specifies the number of samples used to calculate the ambient pressure.
* RMS noise is specified with six pascal (without averaging) and decreases
* down to 3 pascal when using an oversampling setting of 3.
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*
* This program is distributed in the hope that it will be useful,
* but WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
* GNU General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
*/
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
#include <linux/module.h>
#include <linux/device.h>
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/delay.h>
#include <linux/of.h>
#include "bmp085.h"
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
#define BMP085_CHIP_ID 0x55
#define BMP085_CALIBRATION_DATA_START 0xAA
#define BMP085_CALIBRATION_DATA_LENGTH 11 /* 16 bit values */
#define BMP085_CHIP_ID_REG 0xD0
#define BMP085_CTRL_REG 0xF4
#define BMP085_TEMP_MEASUREMENT 0x2E
#define BMP085_PRESSURE_MEASUREMENT 0x34
#define BMP085_CONVERSION_REGISTER_MSB 0xF6
#define BMP085_CONVERSION_REGISTER_LSB 0xF7
#define BMP085_CONVERSION_REGISTER_XLSB 0xF8
#define BMP085_TEMP_CONVERSION_TIME 5
struct bmp085_calibration_data {
s16 AC1, AC2, AC3;
u16 AC4, AC5, AC6;
s16 B1, B2;
s16 MB, MC, MD;
};
struct bmp085_data {
struct device *dev;
struct regmap *regmap;
struct mutex lock;
struct bmp085_calibration_data calibration;
u8 oversampling_setting;
u32 raw_temperature;
u32 raw_pressure;
u32 temp_measurement_period;
unsigned long last_temp_measurement;
u8 chip_id;
s32 b6; /* calculated temperature correction coefficient */
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
};
static s32 bmp085_read_calibration_data(struct bmp085_data *data)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
{
u16 tmp[BMP085_CALIBRATION_DATA_LENGTH];
struct bmp085_calibration_data *cali = &(data->calibration);
s32 status = regmap_bulk_read(data->regmap,
BMP085_CALIBRATION_DATA_START, (u8 *)tmp,
(BMP085_CALIBRATION_DATA_LENGTH << 1));
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
if (status < 0)
return status;
cali->AC1 = be16_to_cpu(tmp[0]);
cali->AC2 = be16_to_cpu(tmp[1]);
cali->AC3 = be16_to_cpu(tmp[2]);
cali->AC4 = be16_to_cpu(tmp[3]);
cali->AC5 = be16_to_cpu(tmp[4]);
cali->AC6 = be16_to_cpu(tmp[5]);
cali->B1 = be16_to_cpu(tmp[6]);
cali->B2 = be16_to_cpu(tmp[7]);
cali->MB = be16_to_cpu(tmp[8]);
cali->MC = be16_to_cpu(tmp[9]);
cali->MD = be16_to_cpu(tmp[10]);
return 0;
}
static s32 bmp085_update_raw_temperature(struct bmp085_data *data)
{
u16 tmp;
s32 status;
mutex_lock(&data->lock);
status = regmap_write(data->regmap, BMP085_CTRL_REG,
BMP085_TEMP_MEASUREMENT);
if (status < 0) {
dev_err(data->dev,
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
"Error while requesting temperature measurement.\n");
goto exit;
}
msleep(BMP085_TEMP_CONVERSION_TIME);
status = regmap_bulk_read(data->regmap, BMP085_CONVERSION_REGISTER_MSB,
&tmp, sizeof(tmp));
if (status < 0) {
dev_err(data->dev,
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
"Error while reading temperature measurement result\n");
goto exit;
}
data->raw_temperature = be16_to_cpu(tmp);
data->last_temp_measurement = jiffies;
status = 0; /* everything ok, return 0 */
exit:
mutex_unlock(&data->lock);
return status;
}
static s32 bmp085_update_raw_pressure(struct bmp085_data *data)
{
u32 tmp = 0;
s32 status;
mutex_lock(&data->lock);
status = regmap_write(data->regmap, BMP085_CTRL_REG,
BMP085_PRESSURE_MEASUREMENT +
(data->oversampling_setting << 6));
if (status < 0) {
dev_err(data->dev,
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
"Error while requesting pressure measurement.\n");
goto exit;
}
/* wait for the end of conversion */
msleep(2+(3 << data->oversampling_setting));
/* copy data into a u32 (4 bytes), but skip the first byte. */
status = regmap_bulk_read(data->regmap, BMP085_CONVERSION_REGISTER_MSB,
((u8 *)&tmp)+1, 3);
if (status < 0) {
dev_err(data->dev,
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
"Error while reading pressure measurement results\n");
goto exit;
}
data->raw_pressure = be32_to_cpu((tmp));
data->raw_pressure >>= (8-data->oversampling_setting);
status = 0; /* everything ok, return 0 */
exit:
mutex_unlock(&data->lock);
return status;
}
/*
* This function starts the temperature measurement and returns the value
* in tenth of a degree celsius.
*/
static s32 bmp085_get_temperature(struct bmp085_data *data, int *temperature)
{
struct bmp085_calibration_data *cali = &data->calibration;
long x1, x2;
int status;
status = bmp085_update_raw_temperature(data);
if (status < 0)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
goto exit;
x1 = ((data->raw_temperature - cali->AC6) * cali->AC5) >> 15;
x2 = (cali->MC << 11) / (x1 + cali->MD);
data->b6 = x1 + x2 - 4000;
/* if NULL just update b6. Used for pressure only measurements */
if (temperature != NULL)
*temperature = (x1+x2+8) >> 4;
exit:
return status;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
}
/*
* This function starts the pressure measurement and returns the value
* in millibar. Since the pressure depends on the ambient temperature,
* a temperature measurement is executed according to the given temperature
* measurement period (default is 1 sec boundary). This period could vary
* and needs to be adjusted according to the sensor environment, i.e. if big
* temperature variations then the temperature needs to be read out often.
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
*/
static s32 bmp085_get_pressure(struct bmp085_data *data, int *pressure)
{
struct bmp085_calibration_data *cali = &data->calibration;
s32 x1, x2, x3, b3;
u32 b4, b7;
s32 p;
int status;
/* alt least every second force an update of the ambient temperature */
if ((data->last_temp_measurement == 0) ||
time_is_before_jiffies(data->last_temp_measurement + 1*HZ)) {
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
status = bmp085_get_temperature(data, NULL);
if (status < 0)
return status;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
}
status = bmp085_update_raw_pressure(data);
if (status < 0)
return status;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
x1 = (data->b6 * data->b6) >> 12;
x1 *= cali->B2;
x1 >>= 11;
x2 = cali->AC2 * data->b6;
x2 >>= 11;
x3 = x1 + x2;
b3 = (((((s32)cali->AC1) * 4 + x3) << data->oversampling_setting) + 2);
b3 >>= 2;
x1 = (cali->AC3 * data->b6) >> 13;
x2 = (cali->B1 * ((data->b6 * data->b6) >> 12)) >> 16;
x3 = (x1 + x2 + 2) >> 2;
b4 = (cali->AC4 * (u32)(x3 + 32768)) >> 15;
b7 = ((u32)data->raw_pressure - b3) *
(50000 >> data->oversampling_setting);
p = ((b7 < 0x80000000) ? ((b7 << 1) / b4) : ((b7 / b4) * 2));
x1 = p >> 8;
x1 *= x1;
x1 = (x1 * 3038) >> 16;
x2 = (-7357 * p) >> 16;
p += (x1 + x2 + 3791) >> 4;
*pressure = p;
return 0;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
}
/*
* This function sets the chip-internal oversampling. Valid values are 0..3.
* The chip will use 2^oversampling samples for internal averaging.
* This influences the measurement time and the accuracy; larger values
* increase both. The datasheet gives an overview on how measurement time,
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
* accuracy and noise correlate.
*/
static void bmp085_set_oversampling(struct bmp085_data *data,
unsigned char oversampling)
{
if (oversampling > 3)
oversampling = 3;
data->oversampling_setting = oversampling;
}
/*
* Returns the currently selected oversampling. Range: 0..3
*/
static unsigned char bmp085_get_oversampling(struct bmp085_data *data)
{
return data->oversampling_setting;
}
/* sysfs callbacks */
static ssize_t set_oversampling(struct device *dev,
struct device_attribute *attr,
const char *buf, size_t count)
{
struct bmp085_data *data = dev_get_drvdata(dev);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
unsigned long oversampling;
int err = kstrtoul(buf, 10, &oversampling);
if (err == 0) {
mutex_lock(&data->lock);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
bmp085_set_oversampling(data, oversampling);
mutex_unlock(&data->lock);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
return count;
}
return err;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
}
static ssize_t show_oversampling(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct bmp085_data *data = dev_get_drvdata(dev);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
return sprintf(buf, "%u\n", bmp085_get_oversampling(data));
}
static DEVICE_ATTR(oversampling, S_IWUSR | S_IRUGO,
show_oversampling, set_oversampling);
static ssize_t show_temperature(struct device *dev,
struct device_attribute *attr, char *buf)
{
int temperature;
int status;
struct bmp085_data *data = dev_get_drvdata(dev);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
status = bmp085_get_temperature(data, &temperature);
if (status < 0)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
return status;
else
return sprintf(buf, "%d\n", temperature);
}
static DEVICE_ATTR(temp0_input, S_IRUGO, show_temperature, NULL);
static ssize_t show_pressure(struct device *dev,
struct device_attribute *attr, char *buf)
{
int pressure;
int status;
struct bmp085_data *data = dev_get_drvdata(dev);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
status = bmp085_get_pressure(data, &pressure);
if (status < 0)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
return status;
else
return sprintf(buf, "%d\n", pressure);
}
static DEVICE_ATTR(pressure0_input, S_IRUGO, show_pressure, NULL);
static struct attribute *bmp085_attributes[] = {
&dev_attr_temp0_input.attr,
&dev_attr_pressure0_input.attr,
&dev_attr_oversampling.attr,
NULL
};
static const struct attribute_group bmp085_attr_group = {
.attrs = bmp085_attributes,
};
int bmp085_detect(struct device *dev)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
{
struct bmp085_data *data = dev_get_drvdata(dev);
unsigned int id;
int ret;
ret = regmap_read(data->regmap, BMP085_CHIP_ID_REG, &id);
if (ret < 0)
return ret;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
if (id != data->chip_id)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
return -ENODEV;
return 0;
}
EXPORT_SYMBOL_GPL(bmp085_detect);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
static void __init bmp085_get_of_properties(struct bmp085_data *data)
{
#ifdef CONFIG_OF
struct device_node *np = data->dev->of_node;
u32 prop;
if (!np)
return;
if (!of_property_read_u32(np, "chip-id", &prop))
data->chip_id = prop & 0xff;
if (!of_property_read_u32(np, "temp-measurement-period", &prop))
data->temp_measurement_period = (prop/100)*HZ;
if (!of_property_read_u32(np, "default-oversampling", &prop))
data->oversampling_setting = prop & 0xff;
#endif
}
static int bmp085_init_client(struct bmp085_data *data)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
{
int status = bmp085_read_calibration_data(data);
if (status < 0)
return status;
/* default settings */
data->chip_id = BMP085_CHIP_ID;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
data->last_temp_measurement = 0;
data->temp_measurement_period = 1*HZ;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
data->oversampling_setting = 3;
bmp085_get_of_properties(data);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
mutex_init(&data->lock);
return 0;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
}
struct regmap_config bmp085_regmap_config = {
.reg_bits = 8,
.val_bits = 8
};
EXPORT_SYMBOL_GPL(bmp085_regmap_config);
__devinit int bmp085_probe(struct device *dev, struct regmap *regmap)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
{
struct bmp085_data *data;
int err = 0;
data = kzalloc(sizeof(struct bmp085_data), GFP_KERNEL);
if (!data) {
err = -ENOMEM;
goto exit;
}
dev_set_drvdata(dev, data);
data->dev = dev;
data->regmap = regmap;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
/* Initialize the BMP085 chip */
err = bmp085_init_client(data);
if (err < 0)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
goto exit_free;
err = bmp085_detect(dev);
if (err < 0) {
dev_err(dev, "%s: chip_id failed!\n", BMP085_NAME);
goto exit_free;
}
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
/* Register sysfs hooks */
err = sysfs_create_group(&dev->kobj, &bmp085_attr_group);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
if (err)
goto exit_free;
dev_info(dev, "Successfully initialized %s!\n", BMP085_NAME);
return 0;
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
exit_free:
kfree(data);
exit:
return err;
}
EXPORT_SYMBOL_GPL(bmp085_probe);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
int bmp085_remove(struct device *dev)
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
{
struct bmp085_data *data = dev_get_drvdata(dev);
sysfs_remove_group(&data->dev->kobj, &bmp085_attr_group);
kfree(data);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
return 0;
}
EXPORT_SYMBOL_GPL(bmp085_remove);
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
MODULE_AUTHOR("Christoph Mair <christoph.mair@gmail.com>");
drivers/misc: support for the pressure sensor BMP085 from Bosch Sensortec This driver adds support for the BMP085 digital pressure sensor from Bosch Sensortec. It exposes a sysfs api to userspace where pressure and temperature measurement results can be read from the pressure0_input and temp0_input file. The chip is able to calculate the average of up to eight samples to increase the accuracy. This feature can be controlled by writing to the oversampling file. The BMP085 digital pressure sensor can measure ambient air pressure and temperature. Both values can be obtained from sysfs files. The pressure is measured by reading from pressure0_input. Valid values range from 30000 to 110000 pascal with a resolution of 1 pascal (=0.01 millibar). temp0_input holds the current temperature in degree celsius, multiplied by 10. This results in a resolution of a tenth degree celsius. Values range from -400 to 850. To increase the accuracy, this chip can calculate the average of 1, 2, 4 or 8 samples. This behavior is controlled through the oversampling sysfs file. Two to the power of the value written to that file specifies how many samples will be used. Valid values: 0..3. [akpm@linux-foundation.org: fix typo] [shubhrajyoti@ti.com: optimize the wait time for the pressure sensor, definition of long is arch dependent so make it u32] [akpm@linux-foundation.org: coding-style fixes] Signed-off-by: Christoph Mair <christoph.mair@gmail.com> Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com> Acked-by: Jonathan Cameron <jic23@cam.ac.uk> Cc: Stefan Schmidt <stefan@datenfreihafen.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-10 00:20:28 +00:00
MODULE_DESCRIPTION("BMP085 driver");
MODULE_LICENSE("GPL");