kernel-ark/include/asm-x86/pci_32.h

#ifndef __i386_PCI_H
#define __i386_PCI_H


#ifdef __KERNEL__


/* Dynamic DMA mapping stuff.
 * i386 has everything mapped statically.
 */

struct pci_dev;

/* The PCI address space does equal the physical memory
 * address space.  The networking and block device layers use
 * this boolean for bounce buffer decisions.
 */
#define PCI_DMA_BUS_IS_PHYS	(1)

/* pci_unmap_{page,single} is a nop so... */
#define DECLARE_PCI_UNMAP_ADDR(ADDR_NAME)
#define DECLARE_PCI_UNMAP_LEN(LEN_NAME)
#define pci_unmap_addr(PTR, ADDR_NAME)		(0)
#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL)	do { } while (0)
#define pci_unmap_len(PTR, LEN_NAME)		(0)
#define pci_unmap_len_set(PTR, LEN_NAME, VAL)	do { } while (0)


#endif /* __KERNEL__ */


#endif /* __i386_PCI_H */
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 22:20:36 +00:00			`#ifndef __i386_PCI_H`
			`#define __i386_PCI_H`


			`#ifdef __KERNEL__`
x86-64: introduce struct pci_sysdata to facilitate sharing of ->sysdata This patch introduces struct pci_sysdata to x86 and x86-64, and converts the existing two users (NUMA, Calgary) to use it. This lays the groundwork for having other users of sysdata, such as the PCI domains work. The Calgary bits are tested, the NUMA bits just look ok. Signed-off-by: Jeff Garzik <jeff@garzik.org> Signed-off-by: Muli Ben-Yehuda <muli@il.ibm.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> 2007-07-21 21:23:39 +00:00
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 22:20:36 +00:00
			`/* Dynamic DMA mapping stuff.`
			`* i386 has everything mapped statically.`
			`*/`

			`struct pci_dev;`

			`/* The PCI address space does equal the physical memory`
			`* address space. The networking and block device layers use`
			`* this boolean for bounce buffer decisions.`
			`*/`
			`#define PCI_DMA_BUS_IS_PHYS (1)`

			`/* pci_unmap_{page,single} is a nop so... */`
			`#define DECLARE_PCI_UNMAP_ADDR(ADDR_NAME)`
			`#define DECLARE_PCI_UNMAP_LEN(LEN_NAME)`
			`#define pci_unmap_addr(PTR, ADDR_NAME) (0)`
			`#define pci_unmap_addr_set(PTR, ADDR_NAME, VAL) do { } while (0)`
			`#define pci_unmap_len(PTR, LEN_NAME) (0)`
			`#define pci_unmap_len_set(PTR, LEN_NAME, VAL) do { } while (0)`

[PATCH] PCI: DMA bursting advice After seeing, at best, "guesses" as to the following kind of information in several drivers, I decided that we really need a way for platforms to specifically give advice in this area for what works best with their PCI controller implementation. Basically, this new interface gives DMA bursting advice on PCI. There are three forms of the advice: 1) Burst as much as possible, it is not necessary to end bursts on some particular boundary for best performance. 2) Burst on some byte count multiple. A DMA burst to some multiple of number of bytes may be done, but it is important to end the burst on an exact multiple for best performance. The best example of this I am aware of are the PPC64 PCI controllers, where if you end a burst mid-cacheline then chip has to refetch the data and the IOMMU translations which hurts performance a lot. 3) Burst on a single byte count multiple. Bursts shall end exactly on the next multiple boundary for best performance. Sparc64 and Alpha's PCI controllers operate this way. They disconnect any device which tries to burst across a cacheline boundary. Actually, newer sparc64 PCI controllers do not have this behavior. That is why the "pdev" is passed into the interface, so I can add code later to check which PCI controller the system is using and give advice accordingly. Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> 2005-06-02 19:55:50 +00:00
Linux-2.6.12-rc2 Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip! 2005-04-16 22:20:36 +00:00			`#endif /* __KERNEL__ */`


			`#endif /* __i386_PCI_H */`