kernel-ark/net/Makefile

72 lines
1.9 KiB
Makefile
Raw Normal View History

#
# Makefile for the linux networking.
#
# 2 Sep 2000, Christoph Hellwig <hch@infradead.org>
# Rewritten to use lists instead of if-statements.
#
obj-y := nonet.o
obj-$(CONFIG_NET) := socket.o core/
tmp-$(CONFIG_COMPAT) := compat.o
obj-$(CONFIG_NET) += $(tmp-y)
# LLC has to be linked before the files in net/802/
obj-$(CONFIG_LLC) += llc/
obj-$(CONFIG_NET) += ethernet/ 802/ sched/ netlink/
obj-$(CONFIG_NETFILTER) += netfilter/
obj-$(CONFIG_INET) += ipv4/
obj-$(CONFIG_XFRM) += xfrm/
obj-$(CONFIG_UNIX) += unix/
obj-$(CONFIG_NET) += ipv6/
obj-$(CONFIG_PACKET) += packet/
obj-$(CONFIG_NET_KEY) += key/
obj-$(CONFIG_BRIDGE) += bridge/
net: Distributed Switch Architecture protocol support Distributed Switch Architecture is a protocol for managing hardware switch chips. It consists of a set of MII management registers and commands to configure the switch, and an ethernet header format to signal which of the ports of the switch a packet was received from or is intended to be sent to. The switches that this driver supports are typically embedded in access points and routers, and a typical setup with a DSA switch looks something like this: +-----------+ +-----------+ | | RGMII | | | +-------+ +------ 1000baseT MDI ("WAN") | | | 6-port +------ 1000baseT MDI ("LAN1") | CPU | | ethernet +------ 1000baseT MDI ("LAN2") | |MIImgmt| switch +------ 1000baseT MDI ("LAN3") | +-------+ w/5 PHYs +------ 1000baseT MDI ("LAN4") | | | | +-----------+ +-----------+ The switch driver presents each port on the switch as a separate network interface to Linux, polls the switch to maintain software link state of those ports, forwards MII management interface accesses to those network interfaces (e.g. as done by ethtool) to the switch, and exposes the switch's hardware statistics counters via the appropriate Linux kernel interfaces. This initial patch supports the MII management interface register layout of the Marvell 88E6123, 88E6161 and 88E6165 switch chips, and supports the "Ethertype DSA" packet tagging format. (There is no officially registered ethertype for the Ethertype DSA packet format, so we just grab a random one. The ethertype to use is programmed into the switch, and the switch driver uses the value of ETH_P_EDSA for this, so this define can be changed at any time in the future if the one we chose is allocated to another protocol or if Ethertype DSA gets its own officially registered ethertype, and everything will continue to work.) Signed-off-by: Lennert Buytenhek <buytenh@marvell.com> Tested-by: Nicolas Pitre <nico@marvell.com> Tested-by: Byron Bradley <byron.bbradley@gmail.com> Tested-by: Tim Ellis <tim.ellis@mac.com> Tested-by: Peter van Valderen <linux@ddcrew.com> Tested-by: Dirk Teurlings <dirk@upexia.nl> Signed-off-by: David S. Miller <davem@davemloft.net>
2008-10-07 13:44:02 +00:00
obj-$(CONFIG_NET_DSA) += dsa/
obj-$(CONFIG_IPX) += ipx/
obj-$(CONFIG_ATALK) += appletalk/
obj-$(CONFIG_WAN_ROUTER) += wanrouter/
obj-$(CONFIG_X25) += x25/
obj-$(CONFIG_LAPB) += lapb/
obj-$(CONFIG_NETROM) += netrom/
obj-$(CONFIG_ROSE) += rose/
obj-$(CONFIG_AX25) += ax25/
obj-$(CONFIG_CAN) += can/
obj-$(CONFIG_IRDA) += irda/
obj-$(CONFIG_BT) += bluetooth/
obj-$(CONFIG_SUNRPC) += sunrpc/
obj-$(CONFIG_AF_RXRPC) += rxrpc/
obj-$(CONFIG_ATM) += atm/
obj-$(CONFIG_L2TP) += l2tp/
obj-$(CONFIG_DECNET) += decnet/
obj-$(CONFIG_ECONET) += econet/
obj-$(CONFIG_PHONET) += phonet/
ifneq ($(CONFIG_VLAN_8021Q),)
obj-y += 8021q/
endif
obj-$(CONFIG_IP_DCCP) += dccp/
obj-$(CONFIG_IP_SCTP) += sctp/
obj-$(CONFIG_RDS) += rds/
obj-$(CONFIG_WIRELESS) += wireless/
obj-$(CONFIG_MAC80211) += mac80211/
obj-$(CONFIG_TIPC) += tipc/
obj-$(CONFIG_NETLABEL) += netlabel/
obj-$(CONFIG_IUCV) += iucv/
obj-$(CONFIG_RFKILL) += rfkill/
obj-$(CONFIG_NET_9P) += 9p/
obj-$(CONFIG_CAIF) += caif/
ifneq ($(CONFIG_DCB),)
obj-y += dcb/
endif
obj-$(CONFIG_IEEE802154) += ieee802154/
ifeq ($(CONFIG_NET),y)
obj-$(CONFIG_SYSCTL) += sysctl_net.o
endif
obj-$(CONFIG_WIMAX) += wimax/
DNS: Separate out CIFS DNS Resolver code Separate out the DNS resolver key type from the CIFS filesystem into its own module so that it can be made available for general use, including the AFS filesystem module. This facility makes it possible for the kernel to upcall to userspace to have it issue DNS requests, package up the replies and present them to the kernel in a useful form. The kernel is then able to cache the DNS replies as keys can be retained in keyrings. Resolver keys are of type "dns_resolver" and have a case-insensitive description that is of the form "[<type>:]<domain_name>". The optional <type> indicates the particular DNS lookup and packaging that's required. The <domain_name> is the query to be made. If <type> isn't given, a basic hostname to IP address lookup is made, and the result is stored in the key in the form of a printable string consisting of a comma-separated list of IPv4 and IPv6 addresses. This key type is supported by userspace helpers driven from /sbin/request-key and configured through /etc/request-key.conf. The cifs.upcall utility is invoked for UNC path server name to IP address resolution. The CIFS functionality is encapsulated by the dns_resolve_unc_to_ip() function, which is used to resolve a UNC path to an IP address for CIFS filesystem. This part remains in the CIFS module for now. See the added Documentation/networking/dns_resolver.txt for more information. Signed-off-by: Wang Lei <wang840925@gmail.com> Signed-off-by: David Howells <dhowells@redhat.com> Acked-by: Jeff Layton <jlayton@redhat.com> Signed-off-by: Steve French <sfrench@us.ibm.com>
2010-08-04 14:16:33 +00:00
obj-$(CONFIG_DNS_RESOLVER) += dns_resolver/
obj-$(CONFIG_CEPH_LIB) += ceph/
obj-$(CONFIG_BATMAN_ADV) += batman-adv/
obj-$(CONFIG_NFC) += nfc/