davidlt/kernel-ark
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity
97bf7a1900
kernel-ark/arch/blackfin/include/asm/context.S

399 lines
5.7 KiB
ArmAsm
Raw Normal View History

blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
/*
Blackfin: mass clean up of copyright/licensing info Bill Gatliff & David Brownell pointed out we were missing some copyrights, and licensing terms in some of the files in ./arch/blackfin, so this fixes things, and cleans them up. It also removes: - verbose GPL text(refer to the top level ./COPYING file) - file names (you are looking at the file) - bug url (it's in the ./MAINTAINERS file) - "or later" on GPL-2, when we did not have that right It also allows some Blackfin-specific assembly files to be under a BSD like license (for people to use them outside of Linux). Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-24 14:11:24 +00:00
* Copyright 2007-2009 Analog Devices Inc.
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
*
Blackfin: mass clean up of copyright/licensing info Bill Gatliff & David Brownell pointed out we were missing some copyrights, and licensing terms in some of the files in ./arch/blackfin, so this fixes things, and cleans them up. It also removes: - verbose GPL text(refer to the top level ./COPYING file) - file names (you are looking at the file) - bug url (it's in the ./MAINTAINERS file) - "or later" on GPL-2, when we did not have that right It also allows some Blackfin-specific assembly files to be under a BSD like license (for people to use them outside of Linux). Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-09-24 14:11:24 +00:00
* Licensed under the GPL-2 or later.
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
*/
[Blackfin] arch: fix gdb testing regression When transferring to IRQ5 from an exception, save SYSCFG in memory across the transfer and clear the trace bit. When we get a single step exception, check whether we can safely clear the trace bit in SYSCFG. We can (and should) clear it after the first instruction of the interrupt handler; the first insn saves SYSCFG to the stack in all handlers. Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2008-05-07 03:41:26 +00:00
/*
* NOTE! The single-stepping code assumes that all interrupt handlers
* start by saving SYSCFG on the stack with their first instruction.
*/
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
/*
* Code to save processor context.
* We even save the register which are preserved by a function call
* - r4, r5, r6, r7, p3, p4, p5
*/
.macro save_context_with_interrupts
[--sp] = SYSCFG;
[--sp] = P0; /*orig_p0*/
[--sp] = R0; /*orig_r0*/
[--sp] = ( R7:0, P5:0 );
[--sp] = fp;
[--sp] = usp;
[--sp] = i0;
[--sp] = i1;
[--sp] = i2;
[--sp] = i3;
[--sp] = m0;
[--sp] = m1;
[--sp] = m2;
[--sp] = m3;
[--sp] = l0;
[--sp] = l1;
[--sp] = l2;
[--sp] = l3;
[--sp] = b0;
[--sp] = b1;
[--sp] = b2;
[--sp] = b3;
[--sp] = a0.x;
[--sp] = a0.w;
[--sp] = a1.x;
[--sp] = a1.w;
[--sp] = LC0;
[--sp] = LC1;
[--sp] = LT0;
[--sp] = LT1;
[--sp] = LB0;
[--sp] = LB1;
[--sp] = ASTAT;
[--sp] = r0; /* Skip reserved */
[--sp] = RETS;
r0 = RETI;
[--sp] = r0;
[--sp] = RETX;
[--sp] = RETN;
[--sp] = RETE;
[--sp] = SEQSTAT;
[--sp] = r0; /* Skip IPEND as well. */
/* Switch to other method of keeping interrupts disabled. */
#ifdef CONFIG_DEBUG_HWERR
r0 = 0x3f;
sti r0;
#else
cli r0;
Blackfin: add support for irqflags tracing Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-19 04:35:28 +00:00
#endif
#ifdef CONFIG_TRACE_IRQFLAGS
sp += -12;
call _trace_hardirqs_off;
sp += 12;
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
#endif
[--sp] = RETI; /*orig_pc*/
/* Clear all L registers. */
r0 = 0 (x);
l0 = r0;
l1 = r0;
l2 = r0;
l3 = r0;
.endm
.macro save_context_syscall
[--sp] = SYSCFG;
[--sp] = P0; /*orig_p0*/
[--sp] = R0; /*orig_r0*/
[--sp] = ( R7:0, P5:0 );
[--sp] = fp;
[--sp] = usp;
[--sp] = i0;
[--sp] = i1;
[--sp] = i2;
[--sp] = i3;
[--sp] = m0;
[--sp] = m1;
[--sp] = m2;
[--sp] = m3;
[--sp] = l0;
[--sp] = l1;
[--sp] = l2;
[--sp] = l3;
[--sp] = b0;
[--sp] = b1;
[--sp] = b2;
[--sp] = b3;
[--sp] = a0.x;
[--sp] = a0.w;
[--sp] = a1.x;
[--sp] = a1.w;
[--sp] = LC0;
[--sp] = LC1;
[--sp] = LT0;
[--sp] = LT1;
[--sp] = LB0;
[--sp] = LB1;
[--sp] = ASTAT;
[--sp] = r0; /* Skip reserved */
[--sp] = RETS;
r0 = RETI;
[--sp] = r0;
[--sp] = RETX;
[--sp] = RETN;
[--sp] = RETE;
[--sp] = SEQSTAT;
[--sp] = r0; /* Skip IPEND as well. */
[--sp] = RETI; /*orig_pc*/
/* Clear all L registers. */
r0 = 0 (x);
l0 = r0;
l1 = r0;
l2 = r0;
l3 = r0;
.endm
.macro save_context_no_interrupts
[--sp] = SYSCFG;
[--sp] = P0; /* orig_p0 */
[--sp] = R0; /* orig_r0 */
[--sp] = ( R7:0, P5:0 );
[--sp] = fp;
[--sp] = usp;
[--sp] = i0;
[--sp] = i1;
[--sp] = i2;
[--sp] = i3;
[--sp] = m0;
[--sp] = m1;
[--sp] = m2;
[--sp] = m3;
[--sp] = l0;
[--sp] = l1;
[--sp] = l2;
[--sp] = l3;
[--sp] = b0;
[--sp] = b1;
[--sp] = b2;
[--sp] = b3;
[--sp] = a0.x;
[--sp] = a0.w;
[--sp] = a1.x;
[--sp] = a1.w;
[--sp] = LC0;
[--sp] = LC1;
[--sp] = LT0;
[--sp] = LT1;
[--sp] = LB0;
[--sp] = LB1;
[--sp] = ASTAT;
#ifdef CONFIG_KGDB
fp = 0(Z);
r1 = sp;
r1 += 60;
r1 += 60;
r1 += 60;
[--sp] = r1;
#else
[--sp] = r0; /* Skip reserved */
#endif
[--sp] = RETS;
r0 = RETI;
[--sp] = r0;
[--sp] = RETX;
[--sp] = RETN;
[--sp] = RETE;
[--sp] = SEQSTAT;
Blackfin: fix handling of IPEND in interrupt context save The interrupt context save logic incorrectly stored the address of the IPEND register rather than its value due to a missing dereference. While we're here, also enable this code for all kernel debugging scenarios and not just when KGDB is enabled. Signed-off-by: Robin Getz <robin.getz@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2009-07-07 02:47:14 +00:00
#ifdef CONFIG_DEBUG_KERNEL
p1.l = lo(IPEND);
p1.h = hi(IPEND);
r1 = [p1];
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
[--sp] = r1;
#else
[--sp] = r0; /* Skip IPEND as well. */
#endif
[--sp] = r0; /*orig_pc*/
/* Clear all L registers. */
r0 = 0 (x);
l0 = r0;
l1 = r0;
l2 = r0;
l3 = r0;
.endm
.macro restore_context_no_interrupts
sp += 4; /* Skip orig_pc */
sp += 4; /* Skip IPEND */
SEQSTAT = [sp++];
RETE = [sp++];
RETN = [sp++];
RETX = [sp++];
r0 = [sp++];
RETI = r0; /* Restore RETI indirectly when in exception */
RETS = [sp++];
sp += 4; /* Skip Reserved */
ASTAT = [sp++];
LB1 = [sp++];
LB0 = [sp++];
LT1 = [sp++];
LT0 = [sp++];
LC1 = [sp++];
LC0 = [sp++];
a1.w = [sp++];
a1.x = [sp++];
a0.w = [sp++];
a0.x = [sp++];
b3 = [sp++];
b2 = [sp++];
b1 = [sp++];
b0 = [sp++];
l3 = [sp++];
l2 = [sp++];
l1 = [sp++];
l0 = [sp++];
m3 = [sp++];
m2 = [sp++];
m1 = [sp++];
m0 = [sp++];
i3 = [sp++];
i2 = [sp++];
i1 = [sp++];
i0 = [sp++];
sp += 4;
fp = [sp++];
( R7 : 0, P5 : 0) = [ SP ++ ];
sp += 8; /* Skip orig_r0/orig_p0 */
SYSCFG = [sp++];
.endm
.macro restore_context_with_interrupts
sp += 4; /* Skip orig_pc */
sp += 4; /* Skip IPEND */
SEQSTAT = [sp++];
RETE = [sp++];
RETN = [sp++];
RETX = [sp++];
RETI = [sp++];
Blackfin: add support for irqflags tracing Signed-off-by: Yi Li <yi.li@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-19 04:35:28 +00:00
#ifdef CONFIG_TRACE_IRQFLAGS
sp += -12;
call _trace_hardirqs_on;
sp += 12;
#endif
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
RETS = [sp++];
Blackfin arch: SMP supporting patchset: Blackfin header files and machine common code Blackfin dual core BF561 processor can support SMP like features. https://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:smp-like In this patch, we provide SMP extend to Blackfin header files and machine common code Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2009-01-07 15:14:39 +00:00
#ifdef CONFIG_SMP
GET_PDA(p0, r0);
r0 = [p0 + PDA_IRQFLAGS];
#else
Blackfin arch: rename irq_flags to bfin_irq_flags rename irq_flags to bfin_irq_flags to avoid namespace collision with common code Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2008-11-18 09:48:22 +00:00
p0.h = _bfin_irq_flags;
p0.l = _bfin_irq_flags;
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
r0 = [p0];
Blackfin arch: SMP supporting patchset: Blackfin header files and machine common code Blackfin dual core BF561 processor can support SMP like features. https://docs.blackfin.uclinux.org/doku.php?id=linux-kernel:smp-like In this patch, we provide SMP extend to Blackfin header files and machine common code Signed-off-by: Graf Yang <graf.yang@analog.com> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2009-01-07 15:14:39 +00:00
#endif
blackfin architecture This adds support for the Analog Devices Blackfin processor architecture, and currently supports the BF533, BF532, BF531, BF537, BF536, BF534, and BF561 (Dual Core) devices, with a variety of development platforms including those avaliable from Analog Devices (BF533-EZKit, BF533-STAMP, BF537-STAMP, BF561-EZKIT), and Bluetechnix! Tinyboards. The Blackfin architecture was jointly developed by Intel and Analog Devices Inc. (ADI) as the Micro Signal Architecture (MSA) core and introduced it in December of 2000. Since then ADI has put this core into its Blackfin processor family of devices. The Blackfin core has the advantages of a clean, orthogonal,RISC-like microprocessor instruction set. It combines a dual-MAC (Multiply/Accumulate), state-of-the-art signal processing engine and single-instruction, multiple-data (SIMD) multimedia capabilities into a single instruction-set architecture. The Blackfin architecture, including the instruction set, is described by the ADSP-BF53x/BF56x Blackfin Processor Programming Reference http://blackfin.uclinux.org/gf/download/frsrelease/29/2549/Blackfin_PRM.pdf The Blackfin processor is already supported by major releases of gcc, and there are binary and source rpms/tarballs for many architectures at: http://blackfin.uclinux.org/gf/project/toolchain/frs There is complete documentation, including "getting started" guides available at: http://docs.blackfin.uclinux.org/ which provides links to the sources and patches you will need in order to set up a cross-compiling environment for bfin-linux-uclibc This patch, as well as the other patches (toolchain, distribution, uClibc) are actively supported by Analog Devices Inc, at: http://blackfin.uclinux.org/ We have tested this on LTP, and our test plan (including pass/fails) can be found at: http://docs.blackfin.uclinux.org/doku.php?id=testing_the_linux_kernel [m.kozlowski@tuxland.pl: balance parenthesis in blackfin header files] Signed-off-by: Bryan Wu <bryan.wu@analog.com> Signed-off-by: Mariusz Kozlowski <m.kozlowski@tuxland.pl> Signed-off-by: Aubrey Li <aubrey.li@analog.com> Signed-off-by: Jie Zhang <jie.zhang@analog.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2007-05-06 21:50:22 +00:00
sti r0;
sp += 4; /* Skip Reserved */
ASTAT = [sp++];
LB1 = [sp++];
LB0 = [sp++];
LT1 = [sp++];
LT0 = [sp++];
LC1 = [sp++];
LC0 = [sp++];
a1.w = [sp++];
a1.x = [sp++];
a0.w = [sp++];
a0.x = [sp++];
b3 = [sp++];
b2 = [sp++];
b1 = [sp++];
b0 = [sp++];
l3 = [sp++];
l2 = [sp++];
l1 = [sp++];
l0 = [sp++];
m3 = [sp++];
m2 = [sp++];
m1 = [sp++];
m0 = [sp++];
i3 = [sp++];
i2 = [sp++];
i1 = [sp++];
i0 = [sp++];
sp += 4;
fp = [sp++];
( R7 : 0, P5 : 0) = [ SP ++ ];
sp += 8; /* Skip orig_r0/orig_p0 */
csync;
SYSCFG = [sp++];
csync;
.endm
Blackfin arch: Faster C implementation of no-MPU CPLB handler This is a mixture ofcMichael McTernan's patch and the existing cplb-mpu code. We ditch the old cplb-nompu implementation, which is a good example of why a good algorithm in a HLL is preferrable to a bad algorithm written in assembly. Rather than try to construct a table of all posible CPLBs and search it, we just create a (smaller) table of memory regions and their attributes. Some of the data structures are now unified for both the mpu and nompu cases. A lot of needless complexity in cplbinit.c is removed. Further optimizations: * compile cplbmgr.c with a lot of -ffixed-reg options, and omit saving these registers on the stack when entering a CPLB exception. * lose cli/nop/nop/sti sequences for some workarounds - these don't * make sense in an exception context Additional code unification should be possible after this. [Mike Frysinger <vapier.adi@gmail.com>: - convert CPP if statements to C if statements - remove redundant statements - use a do...while loop rather than a for loop to get slightly better optimization and to avoid gcc "may be used uninitialized" warnings ... we know that the [id]cplb_nr_bounds variables will never be 0, so this is OK - the no-mpu code was the last user of MAX_MEM_SIZE and with that rewritten, we can punt it - add some BUG_ON() checks to make sure we dont overflow the small cplb_bounds array - add i/d cplb entries for the bootrom because there is functions/data in there we want to access - we do not need a NULL trailing entry as any time we access the bounds arrays, we use the nr_bounds variable ] Signed-off-by: Michael McTernan <mmcternan@airvana.com> Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de> Signed-off-by: Bryan Wu <cooloney@kernel.org>
2009-01-07 15:14:38 +00:00
.macro save_context_cplb
[--sp] = (R7:0, P5:0);
[--sp] = fp;
[--sp] = a0.x;
[--sp] = a0.w;
[--sp] = a1.x;
[--sp] = a1.w;
[--sp] = LC0;
[--sp] = LC1;
[--sp] = LT0;
[--sp] = LT1;
[--sp] = LB0;
[--sp] = LB1;
[--sp] = RETS;
.endm
.macro restore_context_cplb
RETS = [sp++];
LB1 = [sp++];
LB0 = [sp++];
LT1 = [sp++];
LT0 = [sp++];
LC1 = [sp++];
LC0 = [sp++];
a1.w = [sp++];
a1.x = [sp++];
a0.w = [sp++];
a0.x = [sp++];
fp = [sp++];
(R7:0, P5:0) = [SP++];
.endm
Blackfin: initial XIP support Signed-off-by: Barry Song <barry.song@analog.com> Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-01-07 04:11:17 +00:00
.macro pseudo_long_call func:req, scratch:req
#ifdef CONFIG_ROMKERNEL
\scratch\().l = \func;
\scratch\().h = \func;
call (\scratch);
#else
call \func;
#endif
.endm
Reference in New Issue Copy Permalink