xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
#ifndef XEN_OPS_H
|
|
|
|
|
#define XEN_OPS_H
|
|
|
|
|
|
|
|
|
|
#include <linux/init.h>
|
2008-08-21 20:17:56 +00:00
|
|
|
#include <linux/clocksource.h>
|
2008-03-17 23:37:18 +00:00
|
|
|
#include <linux/irqreturn.h>
|
2008-04-02 17:53:55 +00:00
|
|
|
#include <xen/xen-ops.h>
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
|
2007-07-18 01:37:06 +00:00
|
|
|
/* These are code, but not functions. Defined in entry.S */
|
|
|
|
|
extern const char xen_hypervisor_callback[];
|
|
|
|
|
extern const char xen_failsafe_callback[];
|
|
|
|
|
|
2009-02-02 21:55:31 +00:00
|
|
|
extern void *xen_initial_gdt;
|
|
|
|
|
|
2008-05-26 22:31:27 +00:00
|
|
|
struct trap_info;
|
2007-07-18 01:37:06 +00:00
|
|
|
void xen_copy_trap_info(struct trap_info *traps);
|
|
|
|
|
|
2009-01-28 22:35:01 +00:00
|
|
|
DECLARE_PER_CPU(struct vcpu_info, xen_vcpu_info);
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
DECLARE_PER_CPU(unsigned long, xen_cr3);
|
2007-10-16 18:51:30 +00:00
|
|
|
DECLARE_PER_CPU(unsigned long, xen_current_cr3);
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
|
|
|
|
|
extern struct start_info *xen_start_info;
|
2008-05-26 22:31:21 +00:00
|
|
|
extern struct shared_info xen_dummy_shared_info;
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
extern struct shared_info *HYPERVISOR_shared_info;
|
|
|
|
|
|
2008-05-26 22:31:22 +00:00
|
|
|
void xen_setup_mfn_list_list(void);
|
2008-05-26 22:31:27 +00:00
|
|
|
void xen_setup_shared_info(void);
|
2009-11-21 11:32:49 +00:00
|
|
|
void xen_build_mfn_list_list(void);
|
2009-01-28 22:35:01 +00:00
|
|
|
void xen_setup_machphys_mapping(void);
|
2012-06-29 02:47:35 +00:00
|
|
|
void xen_setup_kernel_pagetable(pgd_t *pgd, unsigned long max_pfn);
|
2009-01-28 22:35:01 +00:00
|
|
|
void xen_reserve_top(void);
|
2010-09-15 20:32:49 +00:00
|
|
|
extern unsigned long xen_max_p2m_pfn;
|
2009-01-28 22:35:01 +00:00
|
|
|
|
2010-03-30 18:47:40 +00:00
|
|
|
void xen_set_pat(u64);
|
|
|
|
|
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
char * __init xen_memory_setup(void);
|
|
|
|
|
void __init xen_arch_setup(void);
|
2008-03-17 23:37:17 +00:00
|
|
|
void xen_enable_sysenter(void);
|
2008-07-08 22:07:14 +00:00
|
|
|
void xen_enable_syscall(void);
|
2008-05-31 00:33:02 +00:00
|
|
|
void xen_vcpu_restore(void);
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
|
2010-05-14 11:40:51 +00:00
|
|
|
void xen_callback_vector(void);
|
2012-11-01 21:02:30 +00:00
|
|
|
void xen_hvm_resume_shared_info(void);
|
2010-12-01 14:51:44 +00:00
|
|
|
void xen_unplug_emulated_devices(void);
|
2010-05-14 11:40:51 +00:00
|
|
|
|
2008-05-26 22:31:18 +00:00
|
|
|
void __init xen_build_dynamic_phys_to_machine(void);
|
xen/p2m: Add logic to revector a P2M tree to use __va leafs.
During bootup Xen supplies us with a P2M array. It sticks
it right after the ramdisk, as can be seen with a 128GB PV guest:
(certain parts removed for clarity):
xc_dom_build_image: called
xc_dom_alloc_segment: kernel : 0xffffffff81000000 -> 0xffffffff81e43000 (pfn 0x1000 + 0xe43 pages)
xc_dom_pfn_to_ptr: domU mapping: pfn 0x1000+0xe43 at 0x7f097d8bf000
xc_dom_alloc_segment: ramdisk : 0xffffffff81e43000 -> 0xffffffff925c7000 (pfn 0x1e43 + 0x10784 pages)
xc_dom_pfn_to_ptr: domU mapping: pfn 0x1e43+0x10784 at 0x7f0952dd2000
xc_dom_alloc_segment: phys2mach : 0xffffffff925c7000 -> 0xffffffffa25c7000 (pfn 0x125c7 + 0x10000 pages)
xc_dom_pfn_to_ptr: domU mapping: pfn 0x125c7+0x10000 at 0x7f0942dd2000
xc_dom_alloc_page : start info : 0xffffffffa25c7000 (pfn 0x225c7)
xc_dom_alloc_page : xenstore : 0xffffffffa25c8000 (pfn 0x225c8)
xc_dom_alloc_page : console : 0xffffffffa25c9000 (pfn 0x225c9)
nr_page_tables: 0x0000ffffffffffff/48: 0xffff000000000000 -> 0xffffffffffffffff, 1 table(s)
nr_page_tables: 0x0000007fffffffff/39: 0xffffff8000000000 -> 0xffffffffffffffff, 1 table(s)
nr_page_tables: 0x000000003fffffff/30: 0xffffffff80000000 -> 0xffffffffbfffffff, 1 table(s)
nr_page_tables: 0x00000000001fffff/21: 0xffffffff80000000 -> 0xffffffffa27fffff, 276 table(s)
xc_dom_alloc_segment: page tables : 0xffffffffa25ca000 -> 0xffffffffa26e1000 (pfn 0x225ca + 0x117 pages)
xc_dom_pfn_to_ptr: domU mapping: pfn 0x225ca+0x117 at 0x7f097d7a8000
xc_dom_alloc_page : boot stack : 0xffffffffa26e1000 (pfn 0x226e1)
xc_dom_build_image : virt_alloc_end : 0xffffffffa26e2000
xc_dom_build_image : virt_pgtab_end : 0xffffffffa2800000
So the physical memory and virtual (using __START_KERNEL_map addresses)
layout looks as so:
phys __ka
/------------\ /-------------------\
| 0 | empty | 0xffffffff80000000|
| .. | | .. |
| 16MB | <= kernel starts | 0xffffffff81000000|
| .. | | |
| 30MB | <= kernel ends => | 0xffffffff81e43000|
| .. | & ramdisk starts | .. |
| 293MB | <= ramdisk ends=> | 0xffffffff925c7000|
| .. | & P2M starts | .. |
| .. | | .. |
| 549MB | <= P2M ends => | 0xffffffffa25c7000|
| .. | start_info | 0xffffffffa25c7000|
| .. | xenstore | 0xffffffffa25c8000|
| .. | cosole | 0xffffffffa25c9000|
| 549MB | <= page tables => | 0xffffffffa25ca000|
| .. | | |
| 550MB | <= PGT end => | 0xffffffffa26e1000|
| .. | boot stack | |
\------------/ \-------------------/
As can be seen, the ramdisk, P2M and pagetables are taking
a bit of __ka addresses space. Which is a problem since the
MODULES_VADDR starts at 0xffffffffa0000000 - and P2M sits
right in there! This results during bootup with the inability to
load modules, with this error:
------------[ cut here ]------------
WARNING: at /home/konrad/ssd/linux/mm/vmalloc.c:106 vmap_page_range_noflush+0x2d9/0x370()
Call Trace:
[<ffffffff810719fa>] warn_slowpath_common+0x7a/0xb0
[<ffffffff81030279>] ? __raw_callee_save_xen_pmd_val+0x11/0x1e
[<ffffffff81071a45>] warn_slowpath_null+0x15/0x20
[<ffffffff81130b89>] vmap_page_range_noflush+0x2d9/0x370
[<ffffffff81130c4d>] map_vm_area+0x2d/0x50
[<ffffffff811326d0>] __vmalloc_node_range+0x160/0x250
[<ffffffff810c5369>] ? module_alloc_update_bounds+0x19/0x80
[<ffffffff810c6186>] ? load_module+0x66/0x19c0
[<ffffffff8105cadc>] module_alloc+0x5c/0x60
[<ffffffff810c5369>] ? module_alloc_update_bounds+0x19/0x80
[<ffffffff810c5369>] module_alloc_update_bounds+0x19/0x80
[<ffffffff810c70c3>] load_module+0xfa3/0x19c0
[<ffffffff812491f6>] ? security_file_permission+0x86/0x90
[<ffffffff810c7b3a>] sys_init_module+0x5a/0x220
[<ffffffff815ce339>] system_call_fastpath+0x16/0x1b
---[ end trace fd8f7704fdea0291 ]---
vmalloc: allocation failure, allocated 16384 of 20480 bytes
modprobe: page allocation failure: order:0, mode:0xd2
Since the __va and __ka are 1:1 up to MODULES_VADDR and
cleanup_highmap rids __ka of the ramdisk mapping, what
we want to do is similar - get rid of the P2M in the __ka
address space. There are two ways of fixing this:
1) All P2M lookups instead of using the __ka address would
use the __va address. This means we can safely erase from
__ka space the PMD pointers that point to the PFNs for
P2M array and be OK.
2). Allocate a new array, copy the existing P2M into it,
revector the P2M tree to use that, and return the old
P2M to the memory allocate. This has the advantage that
it sets the stage for using XEN_ELF_NOTE_INIT_P2M
feature. That feature allows us to set the exact virtual
address space we want for the P2M - and allows us to
boot as initial domain on large machines.
So we pick option 2).
This patch only lays the groundwork in the P2M code. The patch
that modifies the MMU is called "xen/mmu: Copy and revector the P2M tree."
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
2012-07-19 17:52:29 +00:00
|
|
|
unsigned long __init xen_revector_p2m_tree(void);
|
2008-05-26 22:31:18 +00:00
|
|
|
|
2008-07-28 18:53:57 +00:00
|
|
|
void xen_init_irq_ops(void);
|
2007-07-18 01:37:06 +00:00
|
|
|
void xen_setup_timer(int cpu);
|
2009-11-21 00:35:55 +00:00
|
|
|
void xen_setup_runstate_info(int cpu);
|
2008-08-22 10:52:15 +00:00
|
|
|
void xen_teardown_timer(int cpu);
|
2008-08-21 20:17:56 +00:00
|
|
|
cycle_t xen_clocksource_read(void);
|
2007-07-18 01:37:06 +00:00
|
|
|
void xen_setup_cpu_clockevents(void);
|
2010-05-14 11:48:19 +00:00
|
|
|
void __init xen_init_time_ops(void);
|
|
|
|
|
void __init xen_hvm_init_time_ops(void);
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
|
2008-03-17 23:37:18 +00:00
|
|
|
irqreturn_t xen_debug_interrupt(int irq, void *dev_id);
|
|
|
|
|
|
2007-10-16 18:51:30 +00:00
|
|
|
bool xen_vcpu_stolen(int vcpu);
|
|
|
|
|
|
2008-11-22 17:37:54 +00:00
|
|
|
void xen_setup_vcpu_info_placement(void);
|
2007-07-18 01:37:06 +00:00
|
|
|
|
2008-07-08 22:06:41 +00:00
|
|
|
#ifdef CONFIG_SMP
|
|
|
|
|
void xen_smp_init(void);
|
2010-12-02 17:55:10 +00:00
|
|
|
void __init xen_hvm_smp_init(void);
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
|
2008-12-17 01:33:57 +00:00
|
|
|
extern cpumask_var_t xen_cpu_initialized_map;
|
2008-07-08 22:06:41 +00:00
|
|
|
#else
|
|
|
|
|
static inline void xen_smp_init(void) {}
|
2010-12-02 17:55:10 +00:00
|
|
|
static inline void xen_hvm_smp_init(void) {}
|
2008-07-08 22:06:41 +00:00
|
|
|
#endif
|
2008-05-26 22:31:27 +00:00
|
|
|
|
x86: Fix performance regression caused by paravirt_ops on native kernels
Xiaohui Xin and some other folks at Intel have been looking into what's
behind the performance hit of paravirt_ops when running native.
It appears that the hit is entirely due to the paravirtualized
spinlocks introduced by:
| commit 8efcbab674de2bee45a2e4cdf97de16b8e609ac8
| Date: Mon Jul 7 12:07:51 2008 -0700
|
| paravirt: introduce a "lock-byte" spinlock implementation
The extra call/return in the spinlock path is somehow
causing an increase in the cycles/instruction of somewhere around 2-7%
(seems to vary quite a lot from test to test). The working theory is
that the CPU's pipeline is getting upset about the
call->call->locked-op->return->return, and seems to be failing to
speculate (though I haven't seen anything definitive about the precise
reasons). This doesn't entirely make sense, because the performance
hit is also visible on unlock and other operations which don't involve
locked instructions. But spinlock operations clearly swamp all the
other pvops operations, even though I can't imagine that they're
nearly as common (there's only a .05% increase in instructions
executed).
If I disable just the pv-spinlock calls, my tests show that pvops is
identical to non-pvops performance on native (my measurements show that
it is actually about .1% faster, but Xiaohui shows a .05% slowdown).
Summary of results, averaging 10 runs of the "mmperf" test, using a
no-pvops build as baseline:
nopv Pv-nospin Pv-spin
CPU cycles 100.00% 99.89% 102.18%
instructions 100.00% 100.10% 100.15%
CPI 100.00% 99.79% 102.03%
cache ref 100.00% 100.84% 100.28%
cache miss 100.00% 90.47% 88.56%
cache miss rate 100.00% 89.72% 88.31%
branches 100.00% 99.93% 100.04%
branch miss 100.00% 103.66% 107.72%
branch miss rt 100.00% 103.73% 107.67%
wallclock 100.00% 99.90% 102.20%
The clear effect here is that the 2% increase in CPI is
directly reflected in the final wallclock time.
(The other interesting effect is that the more ops are
out of line calls via pvops, the lower the cache access
and miss rates. Not too surprising, but it suggests that
the non-pvops kernel is over-inlined. On the flipside,
the branch misses go up correspondingly...)
So, what's the fix?
Paravirt patching turns all the pvops calls into direct calls, so
_spin_lock etc do end up having direct calls. For example, the compiler
generated code for paravirtualized _spin_lock is:
<_spin_lock+0>: mov %gs:0xb4c8,%rax
<_spin_lock+9>: incl 0xffffffffffffe044(%rax)
<_spin_lock+15>: callq *0xffffffff805a5b30
<_spin_lock+22>: retq
The indirect call will get patched to:
<_spin_lock+0>: mov %gs:0xb4c8,%rax
<_spin_lock+9>: incl 0xffffffffffffe044(%rax)
<_spin_lock+15>: callq <__ticket_spin_lock>
<_spin_lock+20>: nop; nop /* or whatever 2-byte nop */
<_spin_lock+22>: retq
One possibility is to inline _spin_lock, etc, when building an
optimised kernel (ie, when there's no spinlock/preempt
instrumentation/debugging enabled). That will remove the outer
call/return pair, returning the instruction stream to a single
call/return, which will presumably execute the same as the non-pvops
case. The downsides arel 1) it will replicate the
preempt_disable/enable code at eack lock/unlock callsite; this code is
fairly small, but not nothing; and 2) the spinlock definitions are
already a very heavily tangled mass of #ifdefs and other preprocessor
magic, and making any changes will be non-trivial.
The other obvious answer is to disable pv-spinlocks. Making them a
separate config option is fairly easy, and it would be trivial to
enable them only when Xen is enabled (as the only non-default user).
But it doesn't really address the common case of a distro build which
is going to have Xen support enabled, and leaves the open question of
whether the native performance cost of pv-spinlocks is worth the
performance improvement on a loaded Xen system (10% saving of overall
system CPU when guests block rather than spin). Still it is a
reasonable short-term workaround.
[ Impact: fix pvops performance regression when running native ]
Analysed-by: "Xin Xiaohui" <xiaohui.xin@intel.com>
Analysed-by: "Li Xin" <xin.li@intel.com>
Analysed-by: "Nakajima Jun" <jun.nakajima@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Xen-devel <xen-devel@lists.xensource.com>
LKML-Reference: <4A0B62F7.5030802@goop.org>
[ fixed the help text ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-05-14 00:16:55 +00:00
|
|
|
#ifdef CONFIG_PARAVIRT_SPINLOCKS
|
|
|
|
|
void __init xen_init_spinlocks(void);
|
2011-05-04 18:19:15 +00:00
|
|
|
void __cpuinit xen_init_lock_cpu(int cpu);
|
x86: Fix performance regression caused by paravirt_ops on native kernels
Xiaohui Xin and some other folks at Intel have been looking into what's
behind the performance hit of paravirt_ops when running native.
It appears that the hit is entirely due to the paravirtualized
spinlocks introduced by:
| commit 8efcbab674de2bee45a2e4cdf97de16b8e609ac8
| Date: Mon Jul 7 12:07:51 2008 -0700
|
| paravirt: introduce a "lock-byte" spinlock implementation
The extra call/return in the spinlock path is somehow
causing an increase in the cycles/instruction of somewhere around 2-7%
(seems to vary quite a lot from test to test). The working theory is
that the CPU's pipeline is getting upset about the
call->call->locked-op->return->return, and seems to be failing to
speculate (though I haven't seen anything definitive about the precise
reasons). This doesn't entirely make sense, because the performance
hit is also visible on unlock and other operations which don't involve
locked instructions. But spinlock operations clearly swamp all the
other pvops operations, even though I can't imagine that they're
nearly as common (there's only a .05% increase in instructions
executed).
If I disable just the pv-spinlock calls, my tests show that pvops is
identical to non-pvops performance on native (my measurements show that
it is actually about .1% faster, but Xiaohui shows a .05% slowdown).
Summary of results, averaging 10 runs of the "mmperf" test, using a
no-pvops build as baseline:
nopv Pv-nospin Pv-spin
CPU cycles 100.00% 99.89% 102.18%
instructions 100.00% 100.10% 100.15%
CPI 100.00% 99.79% 102.03%
cache ref 100.00% 100.84% 100.28%
cache miss 100.00% 90.47% 88.56%
cache miss rate 100.00% 89.72% 88.31%
branches 100.00% 99.93% 100.04%
branch miss 100.00% 103.66% 107.72%
branch miss rt 100.00% 103.73% 107.67%
wallclock 100.00% 99.90% 102.20%
The clear effect here is that the 2% increase in CPI is
directly reflected in the final wallclock time.
(The other interesting effect is that the more ops are
out of line calls via pvops, the lower the cache access
and miss rates. Not too surprising, but it suggests that
the non-pvops kernel is over-inlined. On the flipside,
the branch misses go up correspondingly...)
So, what's the fix?
Paravirt patching turns all the pvops calls into direct calls, so
_spin_lock etc do end up having direct calls. For example, the compiler
generated code for paravirtualized _spin_lock is:
<_spin_lock+0>: mov %gs:0xb4c8,%rax
<_spin_lock+9>: incl 0xffffffffffffe044(%rax)
<_spin_lock+15>: callq *0xffffffff805a5b30
<_spin_lock+22>: retq
The indirect call will get patched to:
<_spin_lock+0>: mov %gs:0xb4c8,%rax
<_spin_lock+9>: incl 0xffffffffffffe044(%rax)
<_spin_lock+15>: callq <__ticket_spin_lock>
<_spin_lock+20>: nop; nop /* or whatever 2-byte nop */
<_spin_lock+22>: retq
One possibility is to inline _spin_lock, etc, when building an
optimised kernel (ie, when there's no spinlock/preempt
instrumentation/debugging enabled). That will remove the outer
call/return pair, returning the instruction stream to a single
call/return, which will presumably execute the same as the non-pvops
case. The downsides arel 1) it will replicate the
preempt_disable/enable code at eack lock/unlock callsite; this code is
fairly small, but not nothing; and 2) the spinlock definitions are
already a very heavily tangled mass of #ifdefs and other preprocessor
magic, and making any changes will be non-trivial.
The other obvious answer is to disable pv-spinlocks. Making them a
separate config option is fairly easy, and it would be trivial to
enable them only when Xen is enabled (as the only non-default user).
But it doesn't really address the common case of a distro build which
is going to have Xen support enabled, and leaves the open question of
whether the native performance cost of pv-spinlocks is worth the
performance improvement on a loaded Xen system (10% saving of overall
system CPU when guests block rather than spin). Still it is a
reasonable short-term workaround.
[ Impact: fix pvops performance regression when running native ]
Analysed-by: "Xin Xiaohui" <xiaohui.xin@intel.com>
Analysed-by: "Li Xin" <xin.li@intel.com>
Analysed-by: "Nakajima Jun" <jun.nakajima@intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Cc: Nick Piggin <npiggin@suse.de>
Cc: Xen-devel <xen-devel@lists.xensource.com>
LKML-Reference: <4A0B62F7.5030802@goop.org>
[ fixed the help text ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2009-05-14 00:16:55 +00:00
|
|
|
void xen_uninit_lock_cpu(int cpu);
|
|
|
|
|
#else
|
|
|
|
|
static inline void xen_init_spinlocks(void)
|
|
|
|
|
{
|
|
|
|
|
}
|
|
|
|
|
static inline void xen_init_lock_cpu(int cpu)
|
|
|
|
|
{
|
|
|
|
|
}
|
|
|
|
|
static inline void xen_uninit_lock_cpu(int cpu)
|
|
|
|
|
{
|
|
|
|
|
}
|
|
|
|
|
#endif
|
2007-07-18 01:37:07 +00:00
|
|
|
|
2011-05-31 14:50:10 +00:00
|
|
|
struct dom0_vga_console_info;
|
|
|
|
|
|
|
|
|
|
#ifdef CONFIG_XEN_DOM0
|
|
|
|
|
void __init xen_init_vga(const struct dom0_vga_console_info *, size_t size);
|
2012-03-20 22:53:10 +00:00
|
|
|
void __init xen_init_apic(void);
|
2011-05-31 14:50:10 +00:00
|
|
|
#else
|
|
|
|
|
static inline void __init xen_init_vga(const struct dom0_vga_console_info *info,
|
|
|
|
|
size_t size)
|
|
|
|
|
{
|
|
|
|
|
}
|
2012-03-20 22:53:10 +00:00
|
|
|
static inline void __init xen_init_apic(void)
|
|
|
|
|
{
|
|
|
|
|
}
|
2011-05-31 14:50:10 +00:00
|
|
|
#endif
|
|
|
|
|
|
2007-07-18 01:37:07 +00:00
|
|
|
/* Declare an asm function, along with symbols needed to make it
|
|
|
|
|
inlineable */
|
|
|
|
|
#define DECL_ASM(ret, name, ...) \
|
|
|
|
|
ret name(__VA_ARGS__); \
|
|
|
|
|
extern char name##_end[]; \
|
|
|
|
|
extern char name##_reloc[] \
|
|
|
|
|
|
|
|
|
|
DECL_ASM(void, xen_irq_enable_direct, void);
|
|
|
|
|
DECL_ASM(void, xen_irq_disable_direct, void);
|
|
|
|
|
DECL_ASM(unsigned long, xen_save_fl_direct, void);
|
|
|
|
|
DECL_ASM(void, xen_restore_fl_direct, unsigned long);
|
|
|
|
|
|
2008-07-08 22:07:00 +00:00
|
|
|
/* These are not functions, and cannot be called normally */
|
2008-04-17 15:40:51 +00:00
|
|
|
void xen_iret(void);
|
2008-03-17 23:37:17 +00:00
|
|
|
void xen_sysexit(void);
|
2008-07-08 22:07:14 +00:00
|
|
|
void xen_sysret32(void);
|
|
|
|
|
void xen_sysret64(void);
|
2008-07-08 22:07:00 +00:00
|
|
|
void xen_adjust_exception_frame(void);
|
2008-03-17 23:37:17 +00:00
|
|
|
|
2010-07-15 18:56:49 +00:00
|
|
|
extern int xen_panic_handler_init(void);
|
|
|
|
|
|
xen: Core Xen implementation
This patch is a rollup of all the core pieces of the Xen
implementation, including:
- booting and setup
- pagetable setup
- privileged instructions
- segmentation
- interrupt flags
- upcalls
- multicall batching
BOOTING AND SETUP
The vmlinux image is decorated with ELF notes which tell the Xen
domain builder what the kernel's requirements are; the domain builder
then constructs the address space accordingly and starts the kernel.
Xen has its own entrypoint for the kernel (contained in an ELF note).
The ELF notes are set up by xen-head.S, which is included into head.S.
In principle it could be linked separately, but it seems to provoke
lots of binutils bugs.
Because the domain builder starts the kernel in a fairly sane state
(32-bit protected mode, paging enabled, flat segments set up), there's
not a lot of setup needed before starting the kernel proper. The main
steps are:
1. Install the Xen paravirt_ops, which is simply a matter of a
structure assignment.
2. Set init_mm to use the Xen-supplied pagetables (analogous to the
head.S generated pagetables in a native boot).
3. Reserve address space for Xen, since it takes a chunk at the top
of the address space for its own use.
4. Call start_kernel()
PAGETABLE SETUP
Once we hit the main kernel boot sequence, it will end up calling back
via paravirt_ops to set up various pieces of Xen specific state. One
of the critical things which requires a bit of extra care is the
construction of the initial init_mm pagetable. Because Xen places
tight constraints on pagetables (an active pagetable must always be
valid, and must always be mapped read-only to the guest domain), we
need to be careful when constructing the new pagetable to keep these
constraints in mind. It turns out that the easiest way to do this is
use the initial Xen-provided pagetable as a template, and then just
insert new mappings for memory where a mapping doesn't already exist.
This means that during pagetable setup, it uses a special version of
xen_set_pte which ignores any attempt to remap a read-only page as
read-write (since Xen will map its own initial pagetable as RO), but
lets other changes to the ptes happen, so that things like NX are set
properly.
PRIVILEGED INSTRUCTIONS AND SEGMENTATION
When the kernel runs under Xen, it runs in ring 1 rather than ring 0.
This means that it is more privileged than user-mode in ring 3, but it
still can't run privileged instructions directly. Non-performance
critical instructions are dealt with by taking a privilege exception
and trapping into the hypervisor and emulating the instruction, but
more performance-critical instructions have their own specific
paravirt_ops. In many cases we can avoid having to do any hypercalls
for these instructions, or the Xen implementation is quite different
from the normal native version.
The privileged instructions fall into the broad classes of:
Segmentation: setting up the GDT and the GDT entries, LDT,
TLS and so on. Xen doesn't allow the GDT to be directly
modified; all GDT updates are done via hypercalls where the new
entries can be validated. This is important because Xen uses
segment limits to prevent the guest kernel from damaging the
hypervisor itself.
Traps and exceptions: Xen uses a special format for trap entrypoints,
so when the kernel wants to set an IDT entry, it needs to be
converted to the form Xen expects. Xen sets int 0x80 up specially
so that the trap goes straight from userspace into the guest kernel
without going via the hypervisor. sysenter isn't supported.
Kernel stack: The esp0 entry is extracted from the tss and provided to
Xen.
TLB operations: the various TLB calls are mapped into corresponding
Xen hypercalls.
Control registers: all the control registers are privileged. The most
important is cr3, which points to the base of the current pagetable,
and we handle it specially.
Another instruction we treat specially is CPUID, even though its not
privileged. We want to control what CPU features are visible to the
rest of the kernel, and so CPUID ends up going into a paravirt_op.
Xen implements this mainly to disable the ACPI and APIC subsystems.
INTERRUPT FLAGS
Xen maintains its own separate flag for masking events, which is
contained within the per-cpu vcpu_info structure. Because the guest
kernel runs in ring 1 and not 0, the IF flag in EFLAGS is completely
ignored (and must be, because even if a guest domain disables
interrupts for itself, it can't disable them overall).
(A note on terminology: "events" and interrupts are effectively
synonymous. However, rather than using an "enable flag", Xen uses a
"mask flag", which blocks event delivery when it is non-zero.)
There are paravirt_ops for each of cli/sti/save_fl/restore_fl, which
are implemented to manage the Xen event mask state. The only thing
worth noting is that when events are unmasked, we need to explicitly
see if there's a pending event and call into the hypervisor to make
sure it gets delivered.
UPCALLS
Xen needs a couple of upcall (or callback) functions to be implemented
by each guest. One is the event upcalls, which is how events
(interrupts, effectively) are delivered to the guests. The other is
the failsafe callback, which is used to report errors in either
reloading a segment register, or caused by iret. These are
implemented in i386/kernel/entry.S so they can jump into the normal
iret_exc path when necessary.
MULTICALL BATCHING
Xen provides a multicall mechanism, which allows multiple hypercalls
to be issued at once in order to mitigate the cost of trapping into
the hypervisor. This is particularly useful for context switches,
since the 4-5 hypercalls they would normally need (reload cr3, update
TLS, maybe update LDT) can be reduced to one. This patch implements a
generic batching mechanism for hypercalls, which gets used in many
places in the Xen code.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Chris Wright <chrisw@sous-sol.org>
Cc: Ian Pratt <ian.pratt@xensource.com>
Cc: Christian Limpach <Christian.Limpach@cl.cam.ac.uk>
Cc: Adrian Bunk <bunk@stusta.de>
2007-07-18 01:37:04 +00:00
|
|
|
#endif /* XEN_OPS_H */
|
