kernel-ark/drivers/net/defxx.c

3746 lines
114 KiB
C
Raw Normal View History

/*
* File Name:
* defxx.c
*
* Copyright Information:
* Copyright Digital Equipment Corporation 1996.
*
* This software may be used and distributed according to the terms of
* the GNU General Public License, incorporated herein by reference.
*
* Abstract:
* A Linux device driver supporting the Digital Equipment Corporation
* FDDI TURBOchannel, EISA and PCI controller families. Supported
* adapters include:
*
* DEC FDDIcontroller/TURBOchannel (DEFTA)
* DEC FDDIcontroller/EISA (DEFEA)
* DEC FDDIcontroller/PCI (DEFPA)
*
* The original author:
* LVS Lawrence V. Stefani <lstefani@yahoo.com>
*
* Maintainers:
* macro Maciej W. Rozycki <macro@linux-mips.org>
*
* Credits:
* I'd like to thank Patricia Cross for helping me get started with
* Linux, David Davies for a lot of help upgrading and configuring
* my development system and for answering many OS and driver
* development questions, and Alan Cox for recommendations and
* integration help on getting FDDI support into Linux. LVS
*
* Driver Architecture:
* The driver architecture is largely based on previous driver work
* for other operating systems. The upper edge interface and
* functions were largely taken from existing Linux device drivers
* such as David Davies' DE4X5.C driver and Donald Becker's TULIP.C
* driver.
*
* Adapter Probe -
* The driver scans for supported EISA adapters by reading the
* SLOT ID register for each EISA slot and making a match
* against the expected value.
*
* Bus-Specific Initialization -
* This driver currently supports both EISA and PCI controller
* families. While the custom DMA chip and FDDI logic is similar
* or identical, the bus logic is very different. After
* initialization, the only bus-specific differences is in how the
* driver enables and disables interrupts. Other than that, the
* run-time critical code behaves the same on both families.
* It's important to note that both adapter families are configured
* to I/O map, rather than memory map, the adapter registers.
*
* Driver Open/Close -
* In the driver open routine, the driver ISR (interrupt service
* routine) is registered and the adapter is brought to an
* operational state. In the driver close routine, the opposite
* occurs; the driver ISR is deregistered and the adapter is
* brought to a safe, but closed state. Users may use consecutive
* commands to bring the adapter up and down as in the following
* example:
* ifconfig fddi0 up
* ifconfig fddi0 down
* ifconfig fddi0 up
*
* Driver Shutdown -
* Apparently, there is no shutdown or halt routine support under
* Linux. This routine would be called during "reboot" or
* "shutdown" to allow the driver to place the adapter in a safe
* state before a warm reboot occurs. To be really safe, the user
* should close the adapter before shutdown (eg. ifconfig fddi0 down)
* to ensure that the adapter DMA engine is taken off-line. However,
* the current driver code anticipates this problem and always issues
* a soft reset of the adapter at the beginning of driver initialization.
* A future driver enhancement in this area may occur in 2.1.X where
* Alan indicated that a shutdown handler may be implemented.
*
* Interrupt Service Routine -
* The driver supports shared interrupts, so the ISR is registered for
* each board with the appropriate flag and the pointer to that board's
* device structure. This provides the context during interrupt
* processing to support shared interrupts and multiple boards.
*
* Interrupt enabling/disabling can occur at many levels. At the host
* end, you can disable system interrupts, or disable interrupts at the
* PIC (on Intel systems). Across the bus, both EISA and PCI adapters
* have a bus-logic chip interrupt enable/disable as well as a DMA
* controller interrupt enable/disable.
*
* The driver currently enables and disables adapter interrupts at the
* bus-logic chip and assumes that Linux will take care of clearing or
* acknowledging any host-based interrupt chips.
*
* Control Functions -
* Control functions are those used to support functions such as adding
* or deleting multicast addresses, enabling or disabling packet
* reception filters, or other custom/proprietary commands. Presently,
* the driver supports the "get statistics", "set multicast list", and
* "set mac address" functions defined by Linux. A list of possible
* enhancements include:
*
* - Custom ioctl interface for executing port interface commands
* - Custom ioctl interface for adding unicast addresses to
* adapter CAM (to support bridge functions).
* - Custom ioctl interface for supporting firmware upgrades.
*
* Hardware (port interface) Support Routines -
* The driver function names that start with "dfx_hw_" represent
* low-level port interface routines that are called frequently. They
* include issuing a DMA or port control command to the adapter,
* resetting the adapter, or reading the adapter state. Since the
* driver initialization and run-time code must make calls into the
* port interface, these routines were written to be as generic and
* usable as possible.
*
* Receive Path -
* The adapter DMA engine supports a 256 entry receive descriptor block
* of which up to 255 entries can be used at any given time. The
* architecture is a standard producer, consumer, completion model in
* which the driver "produces" receive buffers to the adapter, the
* adapter "consumes" the receive buffers by DMAing incoming packet data,
* and the driver "completes" the receive buffers by servicing the
* incoming packet, then "produces" a new buffer and starts the cycle
* again. Receive buffers can be fragmented in up to 16 fragments
* (descriptor entries). For simplicity, this driver posts
* single-fragment receive buffers of 4608 bytes, then allocates a
* sk_buff, copies the data, then reposts the buffer. To reduce CPU
* utilization, a better approach would be to pass up the receive
* buffer (no extra copy) then allocate and post a replacement buffer.
* This is a performance enhancement that should be looked into at
* some point.
*
* Transmit Path -
* Like the receive path, the adapter DMA engine supports a 256 entry
* transmit descriptor block of which up to 255 entries can be used at
* any given time. Transmit buffers can be fragmented in up to 255
* fragments (descriptor entries). This driver always posts one
* fragment per transmit packet request.
*
* The fragment contains the entire packet from FC to end of data.
* Before posting the buffer to the adapter, the driver sets a three-byte
* packet request header (PRH) which is required by the Motorola MAC chip
* used on the adapters. The PRH tells the MAC the type of token to
* receive/send, whether or not to generate and append the CRC, whether
* synchronous or asynchronous framing is used, etc. Since the PRH
* definition is not necessarily consistent across all FDDI chipsets,
* the driver, rather than the common FDDI packet handler routines,
* sets these bytes.
*
* To reduce the amount of descriptor fetches needed per transmit request,
* the driver takes advantage of the fact that there are at least three
* bytes available before the skb->data field on the outgoing transmit
* request. This is guaranteed by having fddi_setup() in net_init.c set
* dev->hard_header_len to 24 bytes. 21 bytes accounts for the largest
* header in an 802.2 SNAP frame. The other 3 bytes are the extra "pad"
* bytes which we'll use to store the PRH.
*
* There's a subtle advantage to adding these pad bytes to the
* hard_header_len, it ensures that the data portion of the packet for
* an 802.2 SNAP frame is longword aligned. Other FDDI driver
* implementations may not need the extra padding and can start copying
* or DMAing directly from the FC byte which starts at skb->data. Should
* another driver implementation need ADDITIONAL padding, the net_init.c
* module should be updated and dev->hard_header_len should be increased.
* NOTE: To maintain the alignment on the data portion of the packet,
* dev->hard_header_len should always be evenly divisible by 4 and at
* least 24 bytes in size.
*
* Modification History:
* Date Name Description
* 16-Aug-96 LVS Created.
* 20-Aug-96 LVS Updated dfx_probe so that version information
* string is only displayed if 1 or more cards are
* found. Changed dfx_rcv_queue_process to copy
* 3 NULL bytes before FC to ensure that data is
* longword aligned in receive buffer.
* 09-Sep-96 LVS Updated dfx_ctl_set_multicast_list to enable
* LLC group promiscuous mode if multicast list
* is too large. LLC individual/group promiscuous
* mode is now disabled if IFF_PROMISC flag not set.
* dfx_xmt_queue_pkt no longer checks for NULL skb
* on Alan Cox recommendation. Added node address
* override support.
* 12-Sep-96 LVS Reset current address to factory address during
* device open. Updated transmit path to post a
* single fragment which includes PRH->end of data.
* Mar 2000 AC Did various cleanups for 2.3.x
* Jun 2000 jgarzik PCI and resource alloc cleanups
* Jul 2000 tjeerd Much cleanup and some bug fixes
* Sep 2000 tjeerd Fix leak on unload, cosmetic code cleanup
* Feb 2001 Skb allocation fixes
* Feb 2001 davej PCI enable cleanups.
* 04 Aug 2003 macro Converted to the DMA API.
* 14 Aug 2004 macro Fix device names reported.
* 14 Jun 2005 macro Use irqreturn_t.
* 23 Oct 2006 macro Big-endian host support.
* 14 Dec 2006 macro TURBOchannel support.
*/
/* Include files */
#include <linux/bitops.h>
#include <linux/compiler.h>
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/eisa.h>
#include <linux/errno.h>
#include <linux/fddidevice.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/pci.h>
#include <linux/skbuff.h>
#include <linux/slab.h>
#include <linux/string.h>
#include <linux/tc.h>
#include <asm/byteorder.h>
#include <asm/io.h>
#include "defxx.h"
/* Version information string should be updated prior to each new release! */
#define DRV_NAME "defxx"
#define DRV_VERSION "v1.10"
#define DRV_RELDATE "2006/12/14"
static char version[] __devinitdata =
DRV_NAME ": " DRV_VERSION " " DRV_RELDATE
" Lawrence V. Stefani and others\n";
#define DYNAMIC_BUFFERS 1
#define SKBUFF_RX_COPYBREAK 200
/*
* NEW_SKB_SIZE = PI_RCV_DATA_K_SIZE_MAX+128 to allow 128 byte
* alignment for compatibility with old EISA boards.
*/
#define NEW_SKB_SIZE (PI_RCV_DATA_K_SIZE_MAX+128)
#ifdef CONFIG_PCI
#define DFX_BUS_PCI(dev) (dev->bus == &pci_bus_type)
#else
#define DFX_BUS_PCI(dev) 0
#endif
#ifdef CONFIG_EISA
#define DFX_BUS_EISA(dev) (dev->bus == &eisa_bus_type)
#else
#define DFX_BUS_EISA(dev) 0
#endif
#ifdef CONFIG_TC
#define DFX_BUS_TC(dev) (dev->bus == &tc_bus_type)
#else
#define DFX_BUS_TC(dev) 0
#endif
#ifdef CONFIG_DEFXX_MMIO
#define DFX_MMIO 1
#else
#define DFX_MMIO 0
#endif
/* Define module-wide (static) routines */
static void dfx_bus_init(struct net_device *dev);
static void dfx_bus_uninit(struct net_device *dev);
static void dfx_bus_config_check(DFX_board_t *bp);
static int dfx_driver_init(struct net_device *dev,
const char *print_name,
resource_size_t bar_start);
static int dfx_adap_init(DFX_board_t *bp, int get_buffers);
static int dfx_open(struct net_device *dev);
static int dfx_close(struct net_device *dev);
static void dfx_int_pr_halt_id(DFX_board_t *bp);
static void dfx_int_type_0_process(DFX_board_t *bp);
static void dfx_int_common(struct net_device *dev);
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 13:55:46 +00:00
static irqreturn_t dfx_interrupt(int irq, void *dev_id);
static struct net_device_stats *dfx_ctl_get_stats(struct net_device *dev);
static void dfx_ctl_set_multicast_list(struct net_device *dev);
static int dfx_ctl_set_mac_address(struct net_device *dev, void *addr);
static int dfx_ctl_update_cam(DFX_board_t *bp);
static int dfx_ctl_update_filters(DFX_board_t *bp);
static int dfx_hw_dma_cmd_req(DFX_board_t *bp);
static int dfx_hw_port_ctrl_req(DFX_board_t *bp, PI_UINT32 command, PI_UINT32 data_a, PI_UINT32 data_b, PI_UINT32 *host_data);
static void dfx_hw_adap_reset(DFX_board_t *bp, PI_UINT32 type);
static int dfx_hw_adap_state_rd(DFX_board_t *bp);
static int dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type);
static int dfx_rcv_init(DFX_board_t *bp, int get_buffers);
static void dfx_rcv_queue_process(DFX_board_t *bp);
static void dfx_rcv_flush(DFX_board_t *bp);
static int dfx_xmt_queue_pkt(struct sk_buff *skb, struct net_device *dev);
static int dfx_xmt_done(DFX_board_t *bp);
static void dfx_xmt_flush(DFX_board_t *bp);
/* Define module-wide (static) variables */
static struct pci_driver dfx_pci_driver;
static struct eisa_driver dfx_eisa_driver;
static struct tc_driver dfx_tc_driver;
/*
* =======================
* = dfx_port_write_long =
* = dfx_port_read_long =
* =======================
*
* Overview:
* Routines for reading and writing values from/to adapter
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
* offset - register offset from base I/O address
* data - for dfx_port_write_long, this is a value to write;
* for dfx_port_read_long, this is a pointer to store
* the read value
*
* Functional Description:
* These routines perform the correct operation to read or write
* the adapter register.
*
* EISA port block base addresses are based on the slot number in which the
* controller is installed. For example, if the EISA controller is installed
* in slot 4, the port block base address is 0x4000. If the controller is
* installed in slot 2, the port block base address is 0x2000, and so on.
* This port block can be used to access PDQ, ESIC, and DEFEA on-board
* registers using the register offsets defined in DEFXX.H.
*
* PCI port block base addresses are assigned by the PCI BIOS or system
* firmware. There is one 128 byte port block which can be accessed. It
* allows for I/O mapping of both PDQ and PFI registers using the register
* offsets defined in DEFXX.H.
*
* Return Codes:
* None
*
* Assumptions:
* bp->base is a valid base I/O address for this adapter.
* offset is a valid register offset for this adapter.
*
* Side Effects:
* Rather than produce macros for these functions, these routines
* are defined using "inline" to ensure that the compiler will
* generate inline code and not waste a procedure call and return.
* This provides all the benefits of macros, but with the
* advantage of strict data type checking.
*/
static inline void dfx_writel(DFX_board_t *bp, int offset, u32 data)
{
writel(data, bp->base.mem + offset);
mb();
}
static inline void dfx_outl(DFX_board_t *bp, int offset, u32 data)
{
outl(data, bp->base.port + offset);
}
static void dfx_port_write_long(DFX_board_t *bp, int offset, u32 data)
{
struct device __maybe_unused *bdev = bp->bus_dev;
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
if (dfx_use_mmio)
dfx_writel(bp, offset, data);
else
dfx_outl(bp, offset, data);
}
static inline void dfx_readl(DFX_board_t *bp, int offset, u32 *data)
{
mb();
*data = readl(bp->base.mem + offset);
}
static inline void dfx_inl(DFX_board_t *bp, int offset, u32 *data)
{
*data = inl(bp->base.port + offset);
}
static void dfx_port_read_long(DFX_board_t *bp, int offset, u32 *data)
{
struct device __maybe_unused *bdev = bp->bus_dev;
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
if (dfx_use_mmio)
dfx_readl(bp, offset, data);
else
dfx_inl(bp, offset, data);
}
/*
* ================
* = dfx_get_bars =
* ================
*
* Overview:
* Retrieves the address range used to access control and status
* registers.
*
* Returns:
* None
*
* Arguments:
* bdev - pointer to device information
* bar_start - pointer to store the start address
* bar_len - pointer to store the length of the area
*
* Assumptions:
* I am sure there are some.
*
* Side Effects:
* None
*/
static void dfx_get_bars(struct device *bdev,
resource_size_t *bar_start, resource_size_t *bar_len)
{
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_eisa = DFX_BUS_EISA(bdev);
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
if (dfx_bus_pci) {
int num = dfx_use_mmio ? 0 : 1;
*bar_start = pci_resource_start(to_pci_dev(bdev), num);
*bar_len = pci_resource_len(to_pci_dev(bdev), num);
}
if (dfx_bus_eisa) {
unsigned long base_addr = to_eisa_device(bdev)->base_addr;
resource_size_t bar;
if (dfx_use_mmio) {
bar = inb(base_addr + PI_ESIC_K_MEM_ADD_CMP_2);
bar <<= 8;
bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_CMP_1);
bar <<= 8;
bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_CMP_0);
bar <<= 16;
*bar_start = bar;
bar = inb(base_addr + PI_ESIC_K_MEM_ADD_MASK_2);
bar <<= 8;
bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_MASK_1);
bar <<= 8;
bar |= inb(base_addr + PI_ESIC_K_MEM_ADD_MASK_0);
bar <<= 16;
*bar_len = (bar | PI_MEM_ADD_MASK_M) + 1;
} else {
*bar_start = base_addr;
*bar_len = PI_ESIC_K_CSR_IO_LEN;
}
}
if (dfx_bus_tc) {
*bar_start = to_tc_dev(bdev)->resource.start +
PI_TC_K_CSR_OFFSET;
*bar_len = PI_TC_K_CSR_LEN;
}
}
static const struct net_device_ops dfx_netdev_ops = {
.ndo_open = dfx_open,
.ndo_stop = dfx_close,
.ndo_start_xmit = dfx_xmt_queue_pkt,
.ndo_get_stats = dfx_ctl_get_stats,
.ndo_set_multicast_list = dfx_ctl_set_multicast_list,
.ndo_set_mac_address = dfx_ctl_set_mac_address,
};
/*
* ================
* = dfx_register =
* ================
*
* Overview:
* Initializes a supported FDDI controller
*
* Returns:
* Condition code
*
* Arguments:
* bdev - pointer to device information
*
* Functional Description:
*
* Return Codes:
* 0 - This device (fddi0, fddi1, etc) configured successfully
* -EBUSY - Failed to get resources, or dfx_driver_init failed.
*
* Assumptions:
* It compiles so it should work :-( (PCI cards do :-)
*
* Side Effects:
* Device structures for FDDI adapters (fddi0, fddi1, etc) are
* initialized and the board resources are read and stored in
* the device structure.
*/
static int __devinit dfx_register(struct device *bdev)
{
static int version_disp;
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
const char *print_name = dev_name(bdev);
struct net_device *dev;
DFX_board_t *bp; /* board pointer */
resource_size_t bar_start = 0; /* pointer to port */
resource_size_t bar_len = 0; /* resource length */
int alloc_size; /* total buffer size used */
struct resource *region;
int err = 0;
if (!version_disp) { /* display version info if adapter is found */
version_disp = 1; /* set display flag to TRUE so that */
printk(version); /* we only display this string ONCE */
}
dev = alloc_fddidev(sizeof(*bp));
if (!dev) {
printk(KERN_ERR "%s: Unable to allocate fddidev, aborting\n",
print_name);
return -ENOMEM;
}
/* Enable PCI device. */
if (dfx_bus_pci && pci_enable_device(to_pci_dev(bdev))) {
printk(KERN_ERR "%s: Cannot enable PCI device, aborting\n",
print_name);
goto err_out;
}
SET_NETDEV_DEV(dev, bdev);
bp = netdev_priv(dev);
bp->bus_dev = bdev;
dev_set_drvdata(bdev, dev);
dfx_get_bars(bdev, &bar_start, &bar_len);
if (dfx_use_mmio)
region = request_mem_region(bar_start, bar_len, print_name);
else
region = request_region(bar_start, bar_len, print_name);
if (!region) {
printk(KERN_ERR "%s: Cannot reserve I/O resource "
"0x%lx @ 0x%lx, aborting\n",
print_name, (long)bar_len, (long)bar_start);
err = -EBUSY;
goto err_out_disable;
}
/* Set up I/O base address. */
if (dfx_use_mmio) {
bp->base.mem = ioremap_nocache(bar_start, bar_len);
if (!bp->base.mem) {
printk(KERN_ERR "%s: Cannot map MMIO\n", print_name);
err = -ENOMEM;
goto err_out_region;
}
} else {
bp->base.port = bar_start;
dev->base_addr = bar_start;
}
/* Initialize new device structure */
dev->netdev_ops = &dfx_netdev_ops;
if (dfx_bus_pci)
pci_set_master(to_pci_dev(bdev));
if (dfx_driver_init(dev, print_name, bar_start) != DFX_K_SUCCESS) {
err = -ENODEV;
goto err_out_unmap;
}
err = register_netdev(dev);
if (err)
goto err_out_kfree;
printk("%s: registered as %s\n", print_name, dev->name);
return 0;
err_out_kfree:
alloc_size = sizeof(PI_DESCR_BLOCK) +
PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX +
#ifndef DYNAMIC_BUFFERS
(bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
#endif
sizeof(PI_CONSUMER_BLOCK) +
(PI_ALIGN_K_DESC_BLK - 1);
if (bp->kmalloced)
dma_free_coherent(bdev, alloc_size,
bp->kmalloced, bp->kmalloced_dma);
err_out_unmap:
if (dfx_use_mmio)
iounmap(bp->base.mem);
err_out_region:
if (dfx_use_mmio)
release_mem_region(bar_start, bar_len);
else
release_region(bar_start, bar_len);
err_out_disable:
if (dfx_bus_pci)
pci_disable_device(to_pci_dev(bdev));
err_out:
free_netdev(dev);
return err;
}
/*
* ================
* = dfx_bus_init =
* ================
*
* Overview:
* Initializes the bus-specific controller logic.
*
* Returns:
* None
*
* Arguments:
* dev - pointer to device information
*
* Functional Description:
* Determine and save adapter IRQ in device table,
* then perform bus-specific logic initialization.
*
* Return Codes:
* None
*
* Assumptions:
* bp->base has already been set with the proper
* base I/O address for this device.
*
* Side Effects:
* Interrupts are enabled at the adapter bus-specific logic.
* Note: Interrupts at the DMA engine (PDQ chip) are not
* enabled yet.
*/
static void __devinit dfx_bus_init(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
struct device *bdev = bp->bus_dev;
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_eisa = DFX_BUS_EISA(bdev);
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
u8 val;
DBG_printk("In dfx_bus_init...\n");
/* Initialize a pointer back to the net_device struct */
bp->dev = dev;
/* Initialize adapter based on bus type */
if (dfx_bus_tc)
dev->irq = to_tc_dev(bdev)->interrupt;
if (dfx_bus_eisa) {
unsigned long base_addr = to_eisa_device(bdev)->base_addr;
/* Get the interrupt level from the ESIC chip. */
val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
val &= PI_CONFIG_STAT_0_M_IRQ;
val >>= PI_CONFIG_STAT_0_V_IRQ;
switch (val) {
case PI_CONFIG_STAT_0_IRQ_K_9:
dev->irq = 9;
break;
case PI_CONFIG_STAT_0_IRQ_K_10:
dev->irq = 10;
break;
case PI_CONFIG_STAT_0_IRQ_K_11:
dev->irq = 11;
break;
case PI_CONFIG_STAT_0_IRQ_K_15:
dev->irq = 15;
break;
}
/*
* Enable memory decoding (MEMCS0) and/or port decoding
* (IOCS1/IOCS0) as appropriate in Function Control
* Register. One of the port chip selects seems to be
* used for the Burst Holdoff register, but this bit of
* documentation is missing and as yet it has not been
* determined which of the two. This is also the reason
* the size of the decoded port range is twice as large
* as one required by the PDQ.
*/
/* Set the decode range of the board. */
val = ((bp->base.port >> 12) << PI_IO_CMP_V_SLOT);
outb(base_addr + PI_ESIC_K_IO_ADD_CMP_0_1, val);
outb(base_addr + PI_ESIC_K_IO_ADD_CMP_0_0, 0);
outb(base_addr + PI_ESIC_K_IO_ADD_CMP_1_1, val);
outb(base_addr + PI_ESIC_K_IO_ADD_CMP_1_0, 0);
val = PI_ESIC_K_CSR_IO_LEN - 1;
outb(base_addr + PI_ESIC_K_IO_ADD_MASK_0_1, (val >> 8) & 0xff);
outb(base_addr + PI_ESIC_K_IO_ADD_MASK_0_0, val & 0xff);
outb(base_addr + PI_ESIC_K_IO_ADD_MASK_1_1, (val >> 8) & 0xff);
outb(base_addr + PI_ESIC_K_IO_ADD_MASK_1_0, val & 0xff);
/* Enable the decoders. */
val = PI_FUNCTION_CNTRL_M_IOCS1 | PI_FUNCTION_CNTRL_M_IOCS0;
if (dfx_use_mmio)
val |= PI_FUNCTION_CNTRL_M_MEMCS0;
outb(base_addr + PI_ESIC_K_FUNCTION_CNTRL, val);
/*
* Enable access to the rest of the module
* (including PDQ and packet memory).
*/
val = PI_SLOT_CNTRL_M_ENB;
outb(base_addr + PI_ESIC_K_SLOT_CNTRL, val);
/*
* Map PDQ registers into memory or port space. This is
* done with a bit in the Burst Holdoff register.
*/
val = inb(base_addr + PI_DEFEA_K_BURST_HOLDOFF);
if (dfx_use_mmio)
val |= PI_BURST_HOLDOFF_V_MEM_MAP;
else
val &= ~PI_BURST_HOLDOFF_V_MEM_MAP;
outb(base_addr + PI_DEFEA_K_BURST_HOLDOFF, val);
/* Enable interrupts at EISA bus interface chip (ESIC) */
val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
val |= PI_CONFIG_STAT_0_M_INT_ENB;
outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, val);
}
if (dfx_bus_pci) {
struct pci_dev *pdev = to_pci_dev(bdev);
/* Get the interrupt level from the PCI Configuration Table */
dev->irq = pdev->irq;
/* Check Latency Timer and set if less than minimal */
pci_read_config_byte(pdev, PCI_LATENCY_TIMER, &val);
if (val < PFI_K_LAT_TIMER_MIN) {
val = PFI_K_LAT_TIMER_DEF;
pci_write_config_byte(pdev, PCI_LATENCY_TIMER, val);
}
/* Enable interrupts at PCI bus interface chip (PFI) */
val = PFI_MODE_M_PDQ_INT_ENB | PFI_MODE_M_DMA_ENB;
dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, val);
}
}
/*
* ==================
* = dfx_bus_uninit =
* ==================
*
* Overview:
* Uninitializes the bus-specific controller logic.
*
* Returns:
* None
*
* Arguments:
* dev - pointer to device information
*
* Functional Description:
* Perform bus-specific logic uninitialization.
*
* Return Codes:
* None
*
* Assumptions:
* bp->base has already been set with the proper
* base I/O address for this device.
*
* Side Effects:
* Interrupts are disabled at the adapter bus-specific logic.
*/
static void __devexit dfx_bus_uninit(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
struct device *bdev = bp->bus_dev;
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_eisa = DFX_BUS_EISA(bdev);
u8 val;
DBG_printk("In dfx_bus_uninit...\n");
/* Uninitialize adapter based on bus type */
if (dfx_bus_eisa) {
unsigned long base_addr = to_eisa_device(bdev)->base_addr;
/* Disable interrupts at EISA bus interface chip (ESIC) */
val = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
val &= ~PI_CONFIG_STAT_0_M_INT_ENB;
outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, val);
}
if (dfx_bus_pci) {
/* Disable interrupts at PCI bus interface chip (PFI) */
dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL, 0);
}
}
/*
* ========================
* = dfx_bus_config_check =
* ========================
*
* Overview:
* Checks the configuration (burst size, full-duplex, etc.) If any parameters
* are illegal, then this routine will set new defaults.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* For Revision 1 FDDI EISA, Revision 2 or later FDDI EISA with rev E or later
* PDQ, and all FDDI PCI controllers, all values are legal.
*
* Return Codes:
* None
*
* Assumptions:
* dfx_adap_init has NOT been called yet so burst size and other items have
* not been set.
*
* Side Effects:
* None
*/
static void __devinit dfx_bus_config_check(DFX_board_t *bp)
{
struct device __maybe_unused *bdev = bp->bus_dev;
int dfx_bus_eisa = DFX_BUS_EISA(bdev);
int status; /* return code from adapter port control call */
u32 host_data; /* LW data returned from port control call */
DBG_printk("In dfx_bus_config_check...\n");
/* Configuration check only valid for EISA adapter */
if (dfx_bus_eisa) {
/*
* First check if revision 2 EISA controller. Rev. 1 cards used
* PDQ revision B, so no workaround needed in this case. Rev. 3
* cards used PDQ revision E, so no workaround needed in this
* case, either. Only Rev. 2 cards used either Rev. D or E
* chips, so we must verify the chip revision on Rev. 2 cards.
*/
if (to_eisa_device(bdev)->id.driver_data == DEFEA_PROD_ID_2) {
/*
* Revision 2 FDDI EISA controller found,
* so let's check PDQ revision of adapter.
*/
status = dfx_hw_port_ctrl_req(bp,
PI_PCTRL_M_SUB_CMD,
PI_SUB_CMD_K_PDQ_REV_GET,
0,
&host_data);
if ((status != DFX_K_SUCCESS) || (host_data == 2))
{
/*
* Either we couldn't determine the PDQ revision, or
* we determined that it is at revision D. In either case,
* we need to implement the workaround.
*/
/* Ensure that the burst size is set to 8 longwords or less */
switch (bp->burst_size)
{
case PI_PDATA_B_DMA_BURST_SIZE_32:
case PI_PDATA_B_DMA_BURST_SIZE_16:
bp->burst_size = PI_PDATA_B_DMA_BURST_SIZE_8;
break;
default:
break;
}
/* Ensure that full-duplex mode is not enabled */
bp->full_duplex_enb = PI_SNMP_K_FALSE;
}
}
}
}
/*
* ===================
* = dfx_driver_init =
* ===================
*
* Overview:
* Initializes remaining adapter board structure information
* and makes sure adapter is in a safe state prior to dfx_open().
*
* Returns:
* Condition code
*
* Arguments:
* dev - pointer to device information
* print_name - printable device name
*
* Functional Description:
* This function allocates additional resources such as the host memory
* blocks needed by the adapter (eg. descriptor and consumer blocks).
* Remaining bus initialization steps are also completed. The adapter
* is also reset so that it is in the DMA_UNAVAILABLE state. The OS
* must call dfx_open() to open the adapter and bring it on-line.
*
* Return Codes:
* DFX_K_SUCCESS - initialization succeeded
* DFX_K_FAILURE - initialization failed - could not allocate memory
* or read adapter MAC address
*
* Assumptions:
* Memory allocated from pci_alloc_consistent() call is physically
* contiguous, locked memory.
*
* Side Effects:
* Adapter is reset and should be in DMA_UNAVAILABLE state before
* returning from this routine.
*/
static int __devinit dfx_driver_init(struct net_device *dev,
const char *print_name,
resource_size_t bar_start)
{
DFX_board_t *bp = netdev_priv(dev);
struct device *bdev = bp->bus_dev;
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_eisa = DFX_BUS_EISA(bdev);
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
int alloc_size; /* total buffer size needed */
char *top_v, *curr_v; /* virtual addrs into memory block */
dma_addr_t top_p, curr_p; /* physical addrs into memory block */
u32 data; /* host data register value */
__le32 le32;
char *board_name = NULL;
DBG_printk("In dfx_driver_init...\n");
/* Initialize bus-specific hardware registers */
dfx_bus_init(dev);
/*
* Initialize default values for configurable parameters
*
* Note: All of these parameters are ones that a user may
* want to customize. It'd be nice to break these
* out into Space.c or someplace else that's more
* accessible/understandable than this file.
*/
bp->full_duplex_enb = PI_SNMP_K_FALSE;
bp->req_ttrt = 8 * 12500; /* 8ms in 80 nanosec units */
bp->burst_size = PI_PDATA_B_DMA_BURST_SIZE_DEF;
bp->rcv_bufs_to_post = RCV_BUFS_DEF;
/*
* Ensure that HW configuration is OK
*
* Note: Depending on the hardware revision, we may need to modify
* some of the configurable parameters to workaround hardware
* limitations. We'll perform this configuration check AFTER
* setting the parameters to their default values.
*/
dfx_bus_config_check(bp);
/* Disable PDQ interrupts first */
dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
/* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
(void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST);
/* Read the factory MAC address from the adapter then save it */
if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_LO, 0,
&data) != DFX_K_SUCCESS) {
printk("%s: Could not read adapter factory MAC address!\n",
print_name);
return(DFX_K_FAILURE);
}
le32 = cpu_to_le32(data);
memcpy(&bp->factory_mac_addr[0], &le32, sizeof(u32));
if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_MLA, PI_PDATA_A_MLA_K_HI, 0,
&data) != DFX_K_SUCCESS) {
printk("%s: Could not read adapter factory MAC address!\n",
print_name);
return(DFX_K_FAILURE);
}
le32 = cpu_to_le32(data);
memcpy(&bp->factory_mac_addr[4], &le32, sizeof(u16));
/*
* Set current address to factory address
*
* Note: Node address override support is handled through
* dfx_ctl_set_mac_address.
*/
memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN);
if (dfx_bus_tc)
board_name = "DEFTA";
if (dfx_bus_eisa)
board_name = "DEFEA";
if (dfx_bus_pci)
board_name = "DEFPA";
pr_info("%s: %s at %saddr = 0x%llx, IRQ = %d, "
"Hardware addr = %02X-%02X-%02X-%02X-%02X-%02X\n",
print_name, board_name, dfx_use_mmio ? "" : "I/O ",
(long long)bar_start, dev->irq,
dev->dev_addr[0], dev->dev_addr[1], dev->dev_addr[2],
dev->dev_addr[3], dev->dev_addr[4], dev->dev_addr[5]);
/*
* Get memory for descriptor block, consumer block, and other buffers
* that need to be DMA read or written to by the adapter.
*/
alloc_size = sizeof(PI_DESCR_BLOCK) +
PI_CMD_REQ_K_SIZE_MAX +
PI_CMD_RSP_K_SIZE_MAX +
#ifndef DYNAMIC_BUFFERS
(bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
#endif
sizeof(PI_CONSUMER_BLOCK) +
(PI_ALIGN_K_DESC_BLK - 1);
bp->kmalloced = top_v = dma_alloc_coherent(bp->bus_dev, alloc_size,
&bp->kmalloced_dma,
GFP_ATOMIC);
if (top_v == NULL) {
printk("%s: Could not allocate memory for host buffers "
"and structures!\n", print_name);
return(DFX_K_FAILURE);
}
memset(top_v, 0, alloc_size); /* zero out memory before continuing */
top_p = bp->kmalloced_dma; /* get physical address of buffer */
/*
* To guarantee the 8K alignment required for the descriptor block, 8K - 1
* plus the amount of memory needed was allocated. The physical address
* is now 8K aligned. By carving up the memory in a specific order,
* we'll guarantee the alignment requirements for all other structures.
*
* Note: If the assumptions change regarding the non-paged, non-cached,
* physically contiguous nature of the memory block or the address
* alignments, then we'll need to implement a different algorithm
* for allocating the needed memory.
*/
curr_p = ALIGN(top_p, PI_ALIGN_K_DESC_BLK);
curr_v = top_v + (curr_p - top_p);
/* Reserve space for descriptor block */
bp->descr_block_virt = (PI_DESCR_BLOCK *) curr_v;
bp->descr_block_phys = curr_p;
curr_v += sizeof(PI_DESCR_BLOCK);
curr_p += sizeof(PI_DESCR_BLOCK);
/* Reserve space for command request buffer */
bp->cmd_req_virt = (PI_DMA_CMD_REQ *) curr_v;
bp->cmd_req_phys = curr_p;
curr_v += PI_CMD_REQ_K_SIZE_MAX;
curr_p += PI_CMD_REQ_K_SIZE_MAX;
/* Reserve space for command response buffer */
bp->cmd_rsp_virt = (PI_DMA_CMD_RSP *) curr_v;
bp->cmd_rsp_phys = curr_p;
curr_v += PI_CMD_RSP_K_SIZE_MAX;
curr_p += PI_CMD_RSP_K_SIZE_MAX;
/* Reserve space for the LLC host receive queue buffers */
bp->rcv_block_virt = curr_v;
bp->rcv_block_phys = curr_p;
#ifndef DYNAMIC_BUFFERS
curr_v += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX);
curr_p += (bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX);
#endif
/* Reserve space for the consumer block */
bp->cons_block_virt = (PI_CONSUMER_BLOCK *) curr_v;
bp->cons_block_phys = curr_p;
/* Display virtual and physical addresses if debug driver */
DBG_printk("%s: Descriptor block virt = %0lX, phys = %0X\n",
print_name,
(long)bp->descr_block_virt, bp->descr_block_phys);
DBG_printk("%s: Command Request buffer virt = %0lX, phys = %0X\n",
print_name, (long)bp->cmd_req_virt, bp->cmd_req_phys);
DBG_printk("%s: Command Response buffer virt = %0lX, phys = %0X\n",
print_name, (long)bp->cmd_rsp_virt, bp->cmd_rsp_phys);
DBG_printk("%s: Receive buffer block virt = %0lX, phys = %0X\n",
print_name, (long)bp->rcv_block_virt, bp->rcv_block_phys);
DBG_printk("%s: Consumer block virt = %0lX, phys = %0X\n",
print_name, (long)bp->cons_block_virt, bp->cons_block_phys);
return(DFX_K_SUCCESS);
}
/*
* =================
* = dfx_adap_init =
* =================
*
* Overview:
* Brings the adapter to the link avail/link unavailable state.
*
* Returns:
* Condition code
*
* Arguments:
* bp - pointer to board information
* get_buffers - non-zero if buffers to be allocated
*
* Functional Description:
* Issues the low-level firmware/hardware calls necessary to bring
* the adapter up, or to properly reset and restore adapter during
* run-time.
*
* Return Codes:
* DFX_K_SUCCESS - Adapter brought up successfully
* DFX_K_FAILURE - Adapter initialization failed
*
* Assumptions:
* bp->reset_type should be set to a valid reset type value before
* calling this routine.
*
* Side Effects:
* Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state
* upon a successful return of this routine.
*/
static int dfx_adap_init(DFX_board_t *bp, int get_buffers)
{
DBG_printk("In dfx_adap_init...\n");
/* Disable PDQ interrupts first */
dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
/* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
if (dfx_hw_dma_uninit(bp, bp->reset_type) != DFX_K_SUCCESS)
{
printk("%s: Could not uninitialize/reset adapter!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/*
* When the PDQ is reset, some false Type 0 interrupts may be pending,
* so we'll acknowledge all Type 0 interrupts now before continuing.
*/
dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, PI_HOST_INT_K_ACK_ALL_TYPE_0);
/*
* Clear Type 1 and Type 2 registers before going to DMA_AVAILABLE state
*
* Note: We only need to clear host copies of these registers. The PDQ reset
* takes care of the on-board register values.
*/
bp->cmd_req_reg.lword = 0;
bp->cmd_rsp_reg.lword = 0;
bp->rcv_xmt_reg.lword = 0;
/* Clear consumer block before going to DMA_AVAILABLE state */
memset(bp->cons_block_virt, 0, sizeof(PI_CONSUMER_BLOCK));
/* Initialize the DMA Burst Size */
if (dfx_hw_port_ctrl_req(bp,
PI_PCTRL_M_SUB_CMD,
PI_SUB_CMD_K_BURST_SIZE_SET,
bp->burst_size,
NULL) != DFX_K_SUCCESS)
{
printk("%s: Could not set adapter burst size!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/*
* Set base address of Consumer Block
*
* Assumption: 32-bit physical address of consumer block is 64 byte
* aligned. That is, bits 0-5 of the address must be zero.
*/
if (dfx_hw_port_ctrl_req(bp,
PI_PCTRL_M_CONS_BLOCK,
bp->cons_block_phys,
0,
NULL) != DFX_K_SUCCESS)
{
printk("%s: Could not set consumer block address!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/*
* Set the base address of Descriptor Block and bring adapter
* to DMA_AVAILABLE state.
*
* Note: We also set the literal and data swapping requirements
* in this command.
*
* Assumption: 32-bit physical address of descriptor block
* is 8Kbyte aligned.
*/
if (dfx_hw_port_ctrl_req(bp, PI_PCTRL_M_INIT,
(u32)(bp->descr_block_phys |
PI_PDATA_A_INIT_M_BSWAP_INIT),
0, NULL) != DFX_K_SUCCESS) {
printk("%s: Could not set descriptor block address!\n",
bp->dev->name);
return DFX_K_FAILURE;
}
/* Set transmit flush timeout value */
bp->cmd_req_virt->cmd_type = PI_CMD_K_CHARS_SET;
bp->cmd_req_virt->char_set.item[0].item_code = PI_ITEM_K_FLUSH_TIME;
bp->cmd_req_virt->char_set.item[0].value = 3; /* 3 seconds */
bp->cmd_req_virt->char_set.item[0].item_index = 0;
bp->cmd_req_virt->char_set.item[1].item_code = PI_ITEM_K_EOL;
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
{
printk("%s: DMA command request failed!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/* Set the initial values for eFDXEnable and MACTReq MIB objects */
bp->cmd_req_virt->cmd_type = PI_CMD_K_SNMP_SET;
bp->cmd_req_virt->snmp_set.item[0].item_code = PI_ITEM_K_FDX_ENB_DIS;
bp->cmd_req_virt->snmp_set.item[0].value = bp->full_duplex_enb;
bp->cmd_req_virt->snmp_set.item[0].item_index = 0;
bp->cmd_req_virt->snmp_set.item[1].item_code = PI_ITEM_K_MAC_T_REQ;
bp->cmd_req_virt->snmp_set.item[1].value = bp->req_ttrt;
bp->cmd_req_virt->snmp_set.item[1].item_index = 0;
bp->cmd_req_virt->snmp_set.item[2].item_code = PI_ITEM_K_EOL;
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
{
printk("%s: DMA command request failed!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/* Initialize adapter CAM */
if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS)
{
printk("%s: Adapter CAM update failed!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/* Initialize adapter filters */
if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS)
{
printk("%s: Adapter filters update failed!\n", bp->dev->name);
return(DFX_K_FAILURE);
}
/*
* Remove any existing dynamic buffers (i.e. if the adapter is being
* reinitialized)
*/
if (get_buffers)
dfx_rcv_flush(bp);
/* Initialize receive descriptor block and produce buffers */
if (dfx_rcv_init(bp, get_buffers))
{
printk("%s: Receive buffer allocation failed\n", bp->dev->name);
if (get_buffers)
dfx_rcv_flush(bp);
return(DFX_K_FAILURE);
}
/* Issue START command and bring adapter to LINK_(UN)AVAILABLE state */
bp->cmd_req_virt->cmd_type = PI_CMD_K_START;
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
{
printk("%s: Start command failed\n", bp->dev->name);
if (get_buffers)
dfx_rcv_flush(bp);
return(DFX_K_FAILURE);
}
/* Initialization succeeded, reenable PDQ interrupts */
dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_ENABLE_DEF_INTS);
return(DFX_K_SUCCESS);
}
/*
* ============
* = dfx_open =
* ============
*
* Overview:
* Opens the adapter
*
* Returns:
* Condition code
*
* Arguments:
* dev - pointer to device information
*
* Functional Description:
* This function brings the adapter to an operational state.
*
* Return Codes:
* 0 - Adapter was successfully opened
* -EAGAIN - Could not register IRQ or adapter initialization failed
*
* Assumptions:
* This routine should only be called for a device that was
* initialized successfully.
*
* Side Effects:
* Adapter should be in LINK_AVAILABLE or LINK_UNAVAILABLE state
* if the open is successful.
*/
static int dfx_open(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
int ret;
DBG_printk("In dfx_open...\n");
/* Register IRQ - support shared interrupts by passing device ptr */
ret = request_irq(dev->irq, dfx_interrupt, IRQF_SHARED, dev->name,
dev);
if (ret) {
printk(KERN_ERR "%s: Requested IRQ %d is busy\n", dev->name, dev->irq);
return ret;
}
/*
* Set current address to factory MAC address
*
* Note: We've already done this step in dfx_driver_init.
* However, it's possible that a user has set a node
* address override, then closed and reopened the
* adapter. Unless we reset the device address field
* now, we'll continue to use the existing modified
* address.
*/
memcpy(dev->dev_addr, bp->factory_mac_addr, FDDI_K_ALEN);
/* Clear local unicast/multicast address tables and counts */
memset(bp->uc_table, 0, sizeof(bp->uc_table));
memset(bp->mc_table, 0, sizeof(bp->mc_table));
bp->uc_count = 0;
bp->mc_count = 0;
/* Disable promiscuous filter settings */
bp->ind_group_prom = PI_FSTATE_K_BLOCK;
bp->group_prom = PI_FSTATE_K_BLOCK;
spin_lock_init(&bp->lock);
/* Reset and initialize adapter */
bp->reset_type = PI_PDATA_A_RESET_M_SKIP_ST; /* skip self-test */
if (dfx_adap_init(bp, 1) != DFX_K_SUCCESS)
{
printk(KERN_ERR "%s: Adapter open failed!\n", dev->name);
free_irq(dev->irq, dev);
return -EAGAIN;
}
/* Set device structure info */
netif_start_queue(dev);
return(0);
}
/*
* =============
* = dfx_close =
* =============
*
* Overview:
* Closes the device/module.
*
* Returns:
* Condition code
*
* Arguments:
* dev - pointer to device information
*
* Functional Description:
* This routine closes the adapter and brings it to a safe state.
* The interrupt service routine is deregistered with the OS.
* The adapter can be opened again with another call to dfx_open().
*
* Return Codes:
* Always return 0.
*
* Assumptions:
* No further requests for this adapter are made after this routine is
* called. dfx_open() can be called to reset and reinitialize the
* adapter.
*
* Side Effects:
* Adapter should be in DMA_UNAVAILABLE state upon completion of this
* routine.
*/
static int dfx_close(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
DBG_printk("In dfx_close...\n");
/* Disable PDQ interrupts first */
dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
/* Place adapter in DMA_UNAVAILABLE state by resetting adapter */
(void) dfx_hw_dma_uninit(bp, PI_PDATA_A_RESET_M_SKIP_ST);
/*
* Flush any pending transmit buffers
*
* Note: It's important that we flush the transmit buffers
* BEFORE we clear our copy of the Type 2 register.
* Otherwise, we'll have no idea how many buffers
* we need to free.
*/
dfx_xmt_flush(bp);
/*
* Clear Type 1 and Type 2 registers after adapter reset
*
* Note: Even though we're closing the adapter, it's
* possible that an interrupt will occur after
* dfx_close is called. Without some assurance to
* the contrary we want to make sure that we don't
* process receive and transmit LLC frames and update
* the Type 2 register with bad information.
*/
bp->cmd_req_reg.lword = 0;
bp->cmd_rsp_reg.lword = 0;
bp->rcv_xmt_reg.lword = 0;
/* Clear consumer block for the same reason given above */
memset(bp->cons_block_virt, 0, sizeof(PI_CONSUMER_BLOCK));
/* Release all dynamically allocate skb in the receive ring. */
dfx_rcv_flush(bp);
/* Clear device structure flags */
netif_stop_queue(dev);
/* Deregister (free) IRQ */
free_irq(dev->irq, dev);
return(0);
}
/*
* ======================
* = dfx_int_pr_halt_id =
* ======================
*
* Overview:
* Displays halt id's in string form.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Determine current halt id and display appropriate string.
*
* Return Codes:
* None
*
* Assumptions:
* None
*
* Side Effects:
* None
*/
static void dfx_int_pr_halt_id(DFX_board_t *bp)
{
PI_UINT32 port_status; /* PDQ port status register value */
PI_UINT32 halt_id; /* PDQ port status halt ID */
/* Read the latest port status */
dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status);
/* Display halt state transition information */
halt_id = (port_status & PI_PSTATUS_M_HALT_ID) >> PI_PSTATUS_V_HALT_ID;
switch (halt_id)
{
case PI_HALT_ID_K_SELFTEST_TIMEOUT:
printk("%s: Halt ID: Selftest Timeout\n", bp->dev->name);
break;
case PI_HALT_ID_K_PARITY_ERROR:
printk("%s: Halt ID: Host Bus Parity Error\n", bp->dev->name);
break;
case PI_HALT_ID_K_HOST_DIR_HALT:
printk("%s: Halt ID: Host-Directed Halt\n", bp->dev->name);
break;
case PI_HALT_ID_K_SW_FAULT:
printk("%s: Halt ID: Adapter Software Fault\n", bp->dev->name);
break;
case PI_HALT_ID_K_HW_FAULT:
printk("%s: Halt ID: Adapter Hardware Fault\n", bp->dev->name);
break;
case PI_HALT_ID_K_PC_TRACE:
printk("%s: Halt ID: FDDI Network PC Trace Path Test\n", bp->dev->name);
break;
case PI_HALT_ID_K_DMA_ERROR:
printk("%s: Halt ID: Adapter DMA Error\n", bp->dev->name);
break;
case PI_HALT_ID_K_IMAGE_CRC_ERROR:
printk("%s: Halt ID: Firmware Image CRC Error\n", bp->dev->name);
break;
case PI_HALT_ID_K_BUS_EXCEPTION:
printk("%s: Halt ID: 68000 Bus Exception\n", bp->dev->name);
break;
default:
printk("%s: Halt ID: Unknown (code = %X)\n", bp->dev->name, halt_id);
break;
}
}
/*
* ==========================
* = dfx_int_type_0_process =
* ==========================
*
* Overview:
* Processes Type 0 interrupts.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Processes all enabled Type 0 interrupts. If the reason for the interrupt
* is a serious fault on the adapter, then an error message is displayed
* and the adapter is reset.
*
* One tricky potential timing window is the rapid succession of "link avail"
* "link unavail" state change interrupts. The acknowledgement of the Type 0
* interrupt must be done before reading the state from the Port Status
* register. This is true because a state change could occur after reading
* the data, but before acknowledging the interrupt. If this state change
* does happen, it would be lost because the driver is using the old state,
* and it will never know about the new state because it subsequently
* acknowledges the state change interrupt.
*
* INCORRECT CORRECT
* read type 0 int reasons read type 0 int reasons
* read adapter state ack type 0 interrupts
* ack type 0 interrupts read adapter state
* ... process interrupt ... ... process interrupt ...
*
* Return Codes:
* None
*
* Assumptions:
* None
*
* Side Effects:
* An adapter reset may occur if the adapter has any Type 0 error interrupts
* or if the port status indicates that the adapter is halted. The driver
* is responsible for reinitializing the adapter with the current CAM
* contents and adapter filter settings.
*/
static void dfx_int_type_0_process(DFX_board_t *bp)
{
PI_UINT32 type_0_status; /* Host Interrupt Type 0 register */
PI_UINT32 state; /* current adap state (from port status) */
/*
* Read host interrupt Type 0 register to determine which Type 0
* interrupts are pending. Immediately write it back out to clear
* those interrupts.
*/
dfx_port_read_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, &type_0_status);
dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_0_STATUS, type_0_status);
/* Check for Type 0 error interrupts */
if (type_0_status & (PI_TYPE_0_STAT_M_NXM |
PI_TYPE_0_STAT_M_PM_PAR_ERR |
PI_TYPE_0_STAT_M_BUS_PAR_ERR))
{
/* Check for Non-Existent Memory error */
if (type_0_status & PI_TYPE_0_STAT_M_NXM)
printk("%s: Non-Existent Memory Access Error\n", bp->dev->name);
/* Check for Packet Memory Parity error */
if (type_0_status & PI_TYPE_0_STAT_M_PM_PAR_ERR)
printk("%s: Packet Memory Parity Error\n", bp->dev->name);
/* Check for Host Bus Parity error */
if (type_0_status & PI_TYPE_0_STAT_M_BUS_PAR_ERR)
printk("%s: Host Bus Parity Error\n", bp->dev->name);
/* Reset adapter and bring it back on-line */
bp->link_available = PI_K_FALSE; /* link is no longer available */
bp->reset_type = 0; /* rerun on-board diagnostics */
printk("%s: Resetting adapter...\n", bp->dev->name);
if (dfx_adap_init(bp, 0) != DFX_K_SUCCESS)
{
printk("%s: Adapter reset failed! Disabling adapter interrupts.\n", bp->dev->name);
dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
return;
}
printk("%s: Adapter reset successful!\n", bp->dev->name);
return;
}
/* Check for transmit flush interrupt */
if (type_0_status & PI_TYPE_0_STAT_M_XMT_FLUSH)
{
/* Flush any pending xmt's and acknowledge the flush interrupt */
bp->link_available = PI_K_FALSE; /* link is no longer available */
dfx_xmt_flush(bp); /* flush any outstanding packets */
(void) dfx_hw_port_ctrl_req(bp,
PI_PCTRL_M_XMT_DATA_FLUSH_DONE,
0,
0,
NULL);
}
/* Check for adapter state change */
if (type_0_status & PI_TYPE_0_STAT_M_STATE_CHANGE)
{
/* Get latest adapter state */
state = dfx_hw_adap_state_rd(bp); /* get adapter state */
if (state == PI_STATE_K_HALTED)
{
/*
* Adapter has transitioned to HALTED state, try to reset
* adapter to bring it back on-line. If reset fails,
* leave the adapter in the broken state.
*/
printk("%s: Controller has transitioned to HALTED state!\n", bp->dev->name);
dfx_int_pr_halt_id(bp); /* display halt id as string */
/* Reset adapter and bring it back on-line */
bp->link_available = PI_K_FALSE; /* link is no longer available */
bp->reset_type = 0; /* rerun on-board diagnostics */
printk("%s: Resetting adapter...\n", bp->dev->name);
if (dfx_adap_init(bp, 0) != DFX_K_SUCCESS)
{
printk("%s: Adapter reset failed! Disabling adapter interrupts.\n", bp->dev->name);
dfx_port_write_long(bp, PI_PDQ_K_REG_HOST_INT_ENB, PI_HOST_INT_K_DISABLE_ALL_INTS);
return;
}
printk("%s: Adapter reset successful!\n", bp->dev->name);
}
else if (state == PI_STATE_K_LINK_AVAIL)
{
bp->link_available = PI_K_TRUE; /* set link available flag */
}
}
}
/*
* ==================
* = dfx_int_common =
* ==================
*
* Overview:
* Interrupt service routine (ISR)
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* This is the ISR which processes incoming adapter interrupts.
*
* Return Codes:
* None
*
* Assumptions:
* This routine assumes PDQ interrupts have not been disabled.
* When interrupts are disabled at the PDQ, the Port Status register
* is automatically cleared. This routine uses the Port Status
* register value to determine whether a Type 0 interrupt occurred,
* so it's important that adapter interrupts are not normally
* enabled/disabled at the PDQ.
*
* It's vital that this routine is NOT reentered for the
* same board and that the OS is not in another section of
* code (eg. dfx_xmt_queue_pkt) for the same board on a
* different thread.
*
* Side Effects:
* Pending interrupts are serviced. Depending on the type of
* interrupt, acknowledging and clearing the interrupt at the
* PDQ involves writing a register to clear the interrupt bit
* or updating completion indices.
*/
static void dfx_int_common(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
PI_UINT32 port_status; /* Port Status register */
/* Process xmt interrupts - frequent case, so always call this routine */
if(dfx_xmt_done(bp)) /* free consumed xmt packets */
netif_wake_queue(dev);
/* Process rcv interrupts - frequent case, so always call this routine */
dfx_rcv_queue_process(bp); /* service received LLC frames */
/*
* Transmit and receive producer and completion indices are updated on the
* adapter by writing to the Type 2 Producer register. Since the frequent
* case is that we'll be processing either LLC transmit or receive buffers,
* we'll optimize I/O writes by doing a single register write here.
*/
dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword);
/* Read PDQ Port Status register to find out which interrupts need processing */
dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status);
/* Process Type 0 interrupts (if any) - infrequent, so only call when needed */
if (port_status & PI_PSTATUS_M_TYPE_0_PENDING)
dfx_int_type_0_process(bp); /* process Type 0 interrupts */
}
/*
* =================
* = dfx_interrupt =
* =================
*
* Overview:
* Interrupt processing routine
*
* Returns:
* Whether a valid interrupt was seen.
*
* Arguments:
* irq - interrupt vector
* dev_id - pointer to device information
*
* Functional Description:
* This routine calls the interrupt processing routine for this adapter. It
* disables and reenables adapter interrupts, as appropriate. We can support
* shared interrupts since the incoming dev_id pointer provides our device
* structure context.
*
* Return Codes:
* IRQ_HANDLED - an IRQ was handled.
* IRQ_NONE - no IRQ was handled.
*
* Assumptions:
* The interrupt acknowledgement at the hardware level (eg. ACKing the PIC
* on Intel-based systems) is done by the operating system outside this
* routine.
*
* System interrupts are enabled through this call.
*
* Side Effects:
* Interrupts are disabled, then reenabled at the adapter.
*/
IRQ: Maintain regs pointer globally rather than passing to IRQ handlers Maintain a per-CPU global "struct pt_regs *" variable which can be used instead of passing regs around manually through all ~1800 interrupt handlers in the Linux kernel. The regs pointer is used in few places, but it potentially costs both stack space and code to pass it around. On the FRV arch, removing the regs parameter from all the genirq function results in a 20% speed up of the IRQ exit path (ie: from leaving timer_interrupt() to leaving do_IRQ()). Where appropriate, an arch may override the generic storage facility and do something different with the variable. On FRV, for instance, the address is maintained in GR28 at all times inside the kernel as part of general exception handling. Having looked over the code, it appears that the parameter may be handed down through up to twenty or so layers of functions. Consider a USB character device attached to a USB hub, attached to a USB controller that posts its interrupts through a cascaded auxiliary interrupt controller. A character device driver may want to pass regs to the sysrq handler through the input layer which adds another few layers of parameter passing. I've build this code with allyesconfig for x86_64 and i386. I've runtested the main part of the code on FRV and i386, though I can't test most of the drivers. I've also done partial conversion for powerpc and MIPS - these at least compile with minimal configurations. This will affect all archs. Mostly the changes should be relatively easy. Take do_IRQ(), store the regs pointer at the beginning, saving the old one: struct pt_regs *old_regs = set_irq_regs(regs); And put the old one back at the end: set_irq_regs(old_regs); Don't pass regs through to generic_handle_irq() or __do_IRQ(). In timer_interrupt(), this sort of change will be necessary: - update_process_times(user_mode(regs)); - profile_tick(CPU_PROFILING, regs); + update_process_times(user_mode(get_irq_regs())); + profile_tick(CPU_PROFILING); I'd like to move update_process_times()'s use of get_irq_regs() into itself, except that i386, alone of the archs, uses something other than user_mode(). Some notes on the interrupt handling in the drivers: (*) input_dev() is now gone entirely. The regs pointer is no longer stored in the input_dev struct. (*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does something different depending on whether it's been supplied with a regs pointer or not. (*) Various IRQ handler function pointers have been moved to type irq_handler_t. Signed-Off-By: David Howells <dhowells@redhat.com> (cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
2006-10-05 13:55:46 +00:00
static irqreturn_t dfx_interrupt(int irq, void *dev_id)
{
struct net_device *dev = dev_id;
DFX_board_t *bp = netdev_priv(dev);
struct device *bdev = bp->bus_dev;
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_eisa = DFX_BUS_EISA(bdev);
int dfx_bus_tc = DFX_BUS_TC(bdev);
/* Service adapter interrupts */
if (dfx_bus_pci) {
u32 status;
dfx_port_read_long(bp, PFI_K_REG_STATUS, &status);
if (!(status & PFI_STATUS_M_PDQ_INT))
return IRQ_NONE;
spin_lock(&bp->lock);
/* Disable PDQ-PFI interrupts at PFI */
dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL,
PFI_MODE_M_DMA_ENB);
/* Call interrupt service routine for this adapter */
dfx_int_common(dev);
/* Clear PDQ interrupt status bit and reenable interrupts */
dfx_port_write_long(bp, PFI_K_REG_STATUS,
PFI_STATUS_M_PDQ_INT);
dfx_port_write_long(bp, PFI_K_REG_MODE_CTRL,
(PFI_MODE_M_PDQ_INT_ENB |
PFI_MODE_M_DMA_ENB));
spin_unlock(&bp->lock);
}
if (dfx_bus_eisa) {
unsigned long base_addr = to_eisa_device(bdev)->base_addr;
u8 status;
status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
if (!(status & PI_CONFIG_STAT_0_M_PEND))
return IRQ_NONE;
spin_lock(&bp->lock);
/* Disable interrupts at the ESIC */
status &= ~PI_CONFIG_STAT_0_M_INT_ENB;
outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, status);
/* Call interrupt service routine for this adapter */
dfx_int_common(dev);
/* Reenable interrupts at the ESIC */
status = inb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0);
status |= PI_CONFIG_STAT_0_M_INT_ENB;
outb(base_addr + PI_ESIC_K_IO_CONFIG_STAT_0, status);
spin_unlock(&bp->lock);
}
if (dfx_bus_tc) {
u32 status;
dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &status);
if (!(status & (PI_PSTATUS_M_RCV_DATA_PENDING |
PI_PSTATUS_M_XMT_DATA_PENDING |
PI_PSTATUS_M_SMT_HOST_PENDING |
PI_PSTATUS_M_UNSOL_PENDING |
PI_PSTATUS_M_CMD_RSP_PENDING |
PI_PSTATUS_M_CMD_REQ_PENDING |
PI_PSTATUS_M_TYPE_0_PENDING)))
return IRQ_NONE;
spin_lock(&bp->lock);
/* Call interrupt service routine for this adapter */
dfx_int_common(dev);
spin_unlock(&bp->lock);
}
return IRQ_HANDLED;
}
/*
* =====================
* = dfx_ctl_get_stats =
* =====================
*
* Overview:
* Get statistics for FDDI adapter
*
* Returns:
* Pointer to FDDI statistics structure
*
* Arguments:
* dev - pointer to device information
*
* Functional Description:
* Gets current MIB objects from adapter, then
* returns FDDI statistics structure as defined
* in if_fddi.h.
*
* Note: Since the FDDI statistics structure is
* still new and the device structure doesn't
* have an FDDI-specific get statistics handler,
* we'll return the FDDI statistics structure as
* a pointer to an Ethernet statistics structure.
* That way, at least the first part of the statistics
* structure can be decoded properly, and it allows
* "smart" applications to perform a second cast to
* decode the FDDI-specific statistics.
*
* We'll have to pay attention to this routine as the
* device structure becomes more mature and LAN media
* independent.
*
* Return Codes:
* None
*
* Assumptions:
* None
*
* Side Effects:
* None
*/
static struct net_device_stats *dfx_ctl_get_stats(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
/* Fill the bp->stats structure with driver-maintained counters */
bp->stats.gen.rx_packets = bp->rcv_total_frames;
bp->stats.gen.tx_packets = bp->xmt_total_frames;
bp->stats.gen.rx_bytes = bp->rcv_total_bytes;
bp->stats.gen.tx_bytes = bp->xmt_total_bytes;
bp->stats.gen.rx_errors = bp->rcv_crc_errors +
bp->rcv_frame_status_errors +
bp->rcv_length_errors;
bp->stats.gen.tx_errors = bp->xmt_length_errors;
bp->stats.gen.rx_dropped = bp->rcv_discards;
bp->stats.gen.tx_dropped = bp->xmt_discards;
bp->stats.gen.multicast = bp->rcv_multicast_frames;
bp->stats.gen.collisions = 0; /* always zero (0) for FDDI */
/* Get FDDI SMT MIB objects */
bp->cmd_req_virt->cmd_type = PI_CMD_K_SMT_MIB_GET;
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
return((struct net_device_stats *) &bp->stats);
/* Fill the bp->stats structure with the SMT MIB object values */
memcpy(bp->stats.smt_station_id, &bp->cmd_rsp_virt->smt_mib_get.smt_station_id, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_station_id));
bp->stats.smt_op_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_op_version_id;
bp->stats.smt_hi_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_hi_version_id;
bp->stats.smt_lo_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_lo_version_id;
memcpy(bp->stats.smt_user_data, &bp->cmd_rsp_virt->smt_mib_get.smt_user_data, sizeof(bp->cmd_rsp_virt->smt_mib_get.smt_user_data));
bp->stats.smt_mib_version_id = bp->cmd_rsp_virt->smt_mib_get.smt_mib_version_id;
bp->stats.smt_mac_cts = bp->cmd_rsp_virt->smt_mib_get.smt_mac_ct;
bp->stats.smt_non_master_cts = bp->cmd_rsp_virt->smt_mib_get.smt_non_master_ct;
bp->stats.smt_master_cts = bp->cmd_rsp_virt->smt_mib_get.smt_master_ct;
bp->stats.smt_available_paths = bp->cmd_rsp_virt->smt_mib_get.smt_available_paths;
bp->stats.smt_config_capabilities = bp->cmd_rsp_virt->smt_mib_get.smt_config_capabilities;
bp->stats.smt_config_policy = bp->cmd_rsp_virt->smt_mib_get.smt_config_policy;
bp->stats.smt_connection_policy = bp->cmd_rsp_virt->smt_mib_get.smt_connection_policy;
bp->stats.smt_t_notify = bp->cmd_rsp_virt->smt_mib_get.smt_t_notify;
bp->stats.smt_stat_rpt_policy = bp->cmd_rsp_virt->smt_mib_get.smt_stat_rpt_policy;
bp->stats.smt_trace_max_expiration = bp->cmd_rsp_virt->smt_mib_get.smt_trace_max_expiration;
bp->stats.smt_bypass_present = bp->cmd_rsp_virt->smt_mib_get.smt_bypass_present;
bp->stats.smt_ecm_state = bp->cmd_rsp_virt->smt_mib_get.smt_ecm_state;
bp->stats.smt_cf_state = bp->cmd_rsp_virt->smt_mib_get.smt_cf_state;
bp->stats.smt_remote_disconnect_flag = bp->cmd_rsp_virt->smt_mib_get.smt_remote_disconnect_flag;
bp->stats.smt_station_status = bp->cmd_rsp_virt->smt_mib_get.smt_station_status;
bp->stats.smt_peer_wrap_flag = bp->cmd_rsp_virt->smt_mib_get.smt_peer_wrap_flag;
bp->stats.smt_time_stamp = bp->cmd_rsp_virt->smt_mib_get.smt_msg_time_stamp.ls;
bp->stats.smt_transition_time_stamp = bp->cmd_rsp_virt->smt_mib_get.smt_transition_time_stamp.ls;
bp->stats.mac_frame_status_functions = bp->cmd_rsp_virt->smt_mib_get.mac_frame_status_functions;
bp->stats.mac_t_max_capability = bp->cmd_rsp_virt->smt_mib_get.mac_t_max_capability;
bp->stats.mac_tvx_capability = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_capability;
bp->stats.mac_available_paths = bp->cmd_rsp_virt->smt_mib_get.mac_available_paths;
bp->stats.mac_current_path = bp->cmd_rsp_virt->smt_mib_get.mac_current_path;
memcpy(bp->stats.mac_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_upstream_nbr, FDDI_K_ALEN);
memcpy(bp->stats.mac_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_downstream_nbr, FDDI_K_ALEN);
memcpy(bp->stats.mac_old_upstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_upstream_nbr, FDDI_K_ALEN);
memcpy(bp->stats.mac_old_downstream_nbr, &bp->cmd_rsp_virt->smt_mib_get.mac_old_downstream_nbr, FDDI_K_ALEN);
bp->stats.mac_dup_address_test = bp->cmd_rsp_virt->smt_mib_get.mac_dup_address_test;
bp->stats.mac_requested_paths = bp->cmd_rsp_virt->smt_mib_get.mac_requested_paths;
bp->stats.mac_downstream_port_type = bp->cmd_rsp_virt->smt_mib_get.mac_downstream_port_type;
memcpy(bp->stats.mac_smt_address, &bp->cmd_rsp_virt->smt_mib_get.mac_smt_address, FDDI_K_ALEN);
bp->stats.mac_t_req = bp->cmd_rsp_virt->smt_mib_get.mac_t_req;
bp->stats.mac_t_neg = bp->cmd_rsp_virt->smt_mib_get.mac_t_neg;
bp->stats.mac_t_max = bp->cmd_rsp_virt->smt_mib_get.mac_t_max;
bp->stats.mac_tvx_value = bp->cmd_rsp_virt->smt_mib_get.mac_tvx_value;
bp->stats.mac_frame_error_threshold = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_threshold;
bp->stats.mac_frame_error_ratio = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_ratio;
bp->stats.mac_rmt_state = bp->cmd_rsp_virt->smt_mib_get.mac_rmt_state;
bp->stats.mac_da_flag = bp->cmd_rsp_virt->smt_mib_get.mac_da_flag;
bp->stats.mac_una_da_flag = bp->cmd_rsp_virt->smt_mib_get.mac_unda_flag;
bp->stats.mac_frame_error_flag = bp->cmd_rsp_virt->smt_mib_get.mac_frame_error_flag;
bp->stats.mac_ma_unitdata_available = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_available;
bp->stats.mac_hardware_present = bp->cmd_rsp_virt->smt_mib_get.mac_hardware_present;
bp->stats.mac_ma_unitdata_enable = bp->cmd_rsp_virt->smt_mib_get.mac_ma_unitdata_enable;
bp->stats.path_tvx_lower_bound = bp->cmd_rsp_virt->smt_mib_get.path_tvx_lower_bound;
bp->stats.path_t_max_lower_bound = bp->cmd_rsp_virt->smt_mib_get.path_t_max_lower_bound;
bp->stats.path_max_t_req = bp->cmd_rsp_virt->smt_mib_get.path_max_t_req;
memcpy(bp->stats.path_configuration, &bp->cmd_rsp_virt->smt_mib_get.path_configuration, sizeof(bp->cmd_rsp_virt->smt_mib_get.path_configuration));
bp->stats.port_my_type[0] = bp->cmd_rsp_virt->smt_mib_get.port_my_type[0];
bp->stats.port_my_type[1] = bp->cmd_rsp_virt->smt_mib_get.port_my_type[1];
bp->stats.port_neighbor_type[0] = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[0];
bp->stats.port_neighbor_type[1] = bp->cmd_rsp_virt->smt_mib_get.port_neighbor_type[1];
bp->stats.port_connection_policies[0] = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[0];
bp->stats.port_connection_policies[1] = bp->cmd_rsp_virt->smt_mib_get.port_connection_policies[1];
bp->stats.port_mac_indicated[0] = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[0];
bp->stats.port_mac_indicated[1] = bp->cmd_rsp_virt->smt_mib_get.port_mac_indicated[1];
bp->stats.port_current_path[0] = bp->cmd_rsp_virt->smt_mib_get.port_current_path[0];
bp->stats.port_current_path[1] = bp->cmd_rsp_virt->smt_mib_get.port_current_path[1];
memcpy(&bp->stats.port_requested_paths[0*3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[0], 3);
memcpy(&bp->stats.port_requested_paths[1*3], &bp->cmd_rsp_virt->smt_mib_get.port_requested_paths[1], 3);
bp->stats.port_mac_placement[0] = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[0];
bp->stats.port_mac_placement[1] = bp->cmd_rsp_virt->smt_mib_get.port_mac_placement[1];
bp->stats.port_available_paths[0] = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[0];
bp->stats.port_available_paths[1] = bp->cmd_rsp_virt->smt_mib_get.port_available_paths[1];
bp->stats.port_pmd_class[0] = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[0];
bp->stats.port_pmd_class[1] = bp->cmd_rsp_virt->smt_mib_get.port_pmd_class[1];
bp->stats.port_connection_capabilities[0] = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[0];
bp->stats.port_connection_capabilities[1] = bp->cmd_rsp_virt->smt_mib_get.port_connection_capabilities[1];
bp->stats.port_bs_flag[0] = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[0];
bp->stats.port_bs_flag[1] = bp->cmd_rsp_virt->smt_mib_get.port_bs_flag[1];
bp->stats.port_ler_estimate[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[0];
bp->stats.port_ler_estimate[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_estimate[1];
bp->stats.port_ler_cutoff[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[0];
bp->stats.port_ler_cutoff[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_cutoff[1];
bp->stats.port_ler_alarm[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[0];
bp->stats.port_ler_alarm[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_alarm[1];
bp->stats.port_connect_state[0] = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[0];
bp->stats.port_connect_state[1] = bp->cmd_rsp_virt->smt_mib_get.port_connect_state[1];
bp->stats.port_pcm_state[0] = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[0];
bp->stats.port_pcm_state[1] = bp->cmd_rsp_virt->smt_mib_get.port_pcm_state[1];
bp->stats.port_pc_withhold[0] = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[0];
bp->stats.port_pc_withhold[1] = bp->cmd_rsp_virt->smt_mib_get.port_pc_withhold[1];
bp->stats.port_ler_flag[0] = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[0];
bp->stats.port_ler_flag[1] = bp->cmd_rsp_virt->smt_mib_get.port_ler_flag[1];
bp->stats.port_hardware_present[0] = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[0];
bp->stats.port_hardware_present[1] = bp->cmd_rsp_virt->smt_mib_get.port_hardware_present[1];
/* Get FDDI counters */
bp->cmd_req_virt->cmd_type = PI_CMD_K_CNTRS_GET;
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
return((struct net_device_stats *) &bp->stats);
/* Fill the bp->stats structure with the FDDI counter values */
bp->stats.mac_frame_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.frame_cnt.ls;
bp->stats.mac_copied_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.copied_cnt.ls;
bp->stats.mac_transmit_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.transmit_cnt.ls;
bp->stats.mac_error_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.error_cnt.ls;
bp->stats.mac_lost_cts = bp->cmd_rsp_virt->cntrs_get.cntrs.lost_cnt.ls;
bp->stats.port_lct_fail_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[0].ls;
bp->stats.port_lct_fail_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.lct_rejects[1].ls;
bp->stats.port_lem_reject_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[0].ls;
bp->stats.port_lem_reject_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.lem_rejects[1].ls;
bp->stats.port_lem_cts[0] = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[0].ls;
bp->stats.port_lem_cts[1] = bp->cmd_rsp_virt->cntrs_get.cntrs.link_errors[1].ls;
return((struct net_device_stats *) &bp->stats);
}
/*
* ==============================
* = dfx_ctl_set_multicast_list =
* ==============================
*
* Overview:
* Enable/Disable LLC frame promiscuous mode reception
* on the adapter and/or update multicast address table.
*
* Returns:
* None
*
* Arguments:
* dev - pointer to device information
*
* Functional Description:
* This routine follows a fairly simple algorithm for setting the
* adapter filters and CAM:
*
* if IFF_PROMISC flag is set
* enable LLC individual/group promiscuous mode
* else
* disable LLC individual/group promiscuous mode
* if number of incoming multicast addresses >
* (CAM max size - number of unicast addresses in CAM)
* enable LLC group promiscuous mode
* set driver-maintained multicast address count to zero
* else
* disable LLC group promiscuous mode
* set driver-maintained multicast address count to incoming count
* update adapter CAM
* update adapter filters
*
* Return Codes:
* None
*
* Assumptions:
* Multicast addresses are presented in canonical (LSB) format.
*
* Side Effects:
* On-board adapter CAM and filters are updated.
*/
static void dfx_ctl_set_multicast_list(struct net_device *dev)
{
DFX_board_t *bp = netdev_priv(dev);
int i; /* used as index in for loop */
struct dev_mc_list *dmi; /* ptr to multicast addr entry */
/* Enable LLC frame promiscuous mode, if necessary */
if (dev->flags & IFF_PROMISC)
bp->ind_group_prom = PI_FSTATE_K_PASS; /* Enable LLC ind/group prom mode */
/* Else, update multicast address table */
else
{
bp->ind_group_prom = PI_FSTATE_K_BLOCK; /* Disable LLC ind/group prom mode */
/*
* Check whether incoming multicast address count exceeds table size
*
* Note: The adapters utilize an on-board 64 entry CAM for
* supporting perfect filtering of multicast packets
* and bridge functions when adding unicast addresses.
* There is no hash function available. To support
* additional multicast addresses, the all multicast
* filter (LLC group promiscuous mode) must be enabled.
*
* The firmware reserves two CAM entries for SMT-related
* multicast addresses, which leaves 62 entries available.
* The following code ensures that we're not being asked
* to add more than 62 addresses to the CAM. If we are,
* the driver will enable the all multicast filter.
* Should the number of multicast addresses drop below
* the high water mark, the filter will be disabled and
* perfect filtering will be used.
*/
if (dev->mc_count > (PI_CMD_ADDR_FILTER_K_SIZE - bp->uc_count))
{
bp->group_prom = PI_FSTATE_K_PASS; /* Enable LLC group prom mode */
bp->mc_count = 0; /* Don't add mc addrs to CAM */
}
else
{
bp->group_prom = PI_FSTATE_K_BLOCK; /* Disable LLC group prom mode */
bp->mc_count = dev->mc_count; /* Add mc addrs to CAM */
}
/* Copy addresses to multicast address table, then update adapter CAM */
dmi = dev->mc_list; /* point to first multicast addr */
for (i=0; i < bp->mc_count; i++)
{
memcpy(&bp->mc_table[i*FDDI_K_ALEN], dmi->dmi_addr, FDDI_K_ALEN);
dmi = dmi->next; /* point to next multicast addr */
}
if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS)
{
DBG_printk("%s: Could not update multicast address table!\n", dev->name);
}
else
{
DBG_printk("%s: Multicast address table updated! Added %d addresses.\n", dev->name, bp->mc_count);
}
}
/* Update adapter filters */
if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS)
{
DBG_printk("%s: Could not update adapter filters!\n", dev->name);
}
else
{
DBG_printk("%s: Adapter filters updated!\n", dev->name);
}
}
/*
* ===========================
* = dfx_ctl_set_mac_address =
* ===========================
*
* Overview:
* Add node address override (unicast address) to adapter
* CAM and update dev_addr field in device table.
*
* Returns:
* None
*
* Arguments:
* dev - pointer to device information
* addr - pointer to sockaddr structure containing unicast address to add
*
* Functional Description:
* The adapter supports node address overrides by adding one or more
* unicast addresses to the adapter CAM. This is similar to adding
* multicast addresses. In this routine we'll update the driver and
* device structures with the new address, then update the adapter CAM
* to ensure that the adapter will copy and strip frames destined and
* sourced by that address.
*
* Return Codes:
* Always returns zero.
*
* Assumptions:
* The address pointed to by addr->sa_data is a valid unicast
* address and is presented in canonical (LSB) format.
*
* Side Effects:
* On-board adapter CAM is updated. On-board adapter filters
* may be updated.
*/
static int dfx_ctl_set_mac_address(struct net_device *dev, void *addr)
{
struct sockaddr *p_sockaddr = (struct sockaddr *)addr;
DFX_board_t *bp = netdev_priv(dev);
/* Copy unicast address to driver-maintained structs and update count */
memcpy(dev->dev_addr, p_sockaddr->sa_data, FDDI_K_ALEN); /* update device struct */
memcpy(&bp->uc_table[0], p_sockaddr->sa_data, FDDI_K_ALEN); /* update driver struct */
bp->uc_count = 1;
/*
* Verify we're not exceeding the CAM size by adding unicast address
*
* Note: It's possible that before entering this routine we've
* already filled the CAM with 62 multicast addresses.
* Since we need to place the node address override into
* the CAM, we have to check to see that we're not
* exceeding the CAM size. If we are, we have to enable
* the LLC group (multicast) promiscuous mode filter as
* in dfx_ctl_set_multicast_list.
*/
if ((bp->uc_count + bp->mc_count) > PI_CMD_ADDR_FILTER_K_SIZE)
{
bp->group_prom = PI_FSTATE_K_PASS; /* Enable LLC group prom mode */
bp->mc_count = 0; /* Don't add mc addrs to CAM */
/* Update adapter filters */
if (dfx_ctl_update_filters(bp) != DFX_K_SUCCESS)
{
DBG_printk("%s: Could not update adapter filters!\n", dev->name);
}
else
{
DBG_printk("%s: Adapter filters updated!\n", dev->name);
}
}
/* Update adapter CAM with new unicast address */
if (dfx_ctl_update_cam(bp) != DFX_K_SUCCESS)
{
DBG_printk("%s: Could not set new MAC address!\n", dev->name);
}
else
{
DBG_printk("%s: Adapter CAM updated with new MAC address\n", dev->name);
}
return(0); /* always return zero */
}
/*
* ======================
* = dfx_ctl_update_cam =
* ======================
*
* Overview:
* Procedure to update adapter CAM (Content Addressable Memory)
* with desired unicast and multicast address entries.
*
* Returns:
* Condition code
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Updates adapter CAM with current contents of board structure
* unicast and multicast address tables. Since there are only 62
* free entries in CAM, this routine ensures that the command
* request buffer is not overrun.
*
* Return Codes:
* DFX_K_SUCCESS - Request succeeded
* DFX_K_FAILURE - Request failed
*
* Assumptions:
* All addresses being added (unicast and multicast) are in canonical
* order.
*
* Side Effects:
* On-board adapter CAM is updated.
*/
static int dfx_ctl_update_cam(DFX_board_t *bp)
{
int i; /* used as index */
PI_LAN_ADDR *p_addr; /* pointer to CAM entry */
/*
* Fill in command request information
*
* Note: Even though both the unicast and multicast address
* table entries are stored as contiguous 6 byte entries,
* the firmware address filter set command expects each
* entry to be two longwords (8 bytes total). We must be
* careful to only copy the six bytes of each unicast and
* multicast table entry into each command entry. This
* is also why we must first clear the entire command
* request buffer.
*/
memset(bp->cmd_req_virt, 0, PI_CMD_REQ_K_SIZE_MAX); /* first clear buffer */
bp->cmd_req_virt->cmd_type = PI_CMD_K_ADDR_FILTER_SET;
p_addr = &bp->cmd_req_virt->addr_filter_set.entry[0];
/* Now add unicast addresses to command request buffer, if any */
for (i=0; i < (int)bp->uc_count; i++)
{
if (i < PI_CMD_ADDR_FILTER_K_SIZE)
{
memcpy(p_addr, &bp->uc_table[i*FDDI_K_ALEN], FDDI_K_ALEN);
p_addr++; /* point to next command entry */
}
}
/* Now add multicast addresses to command request buffer, if any */
for (i=0; i < (int)bp->mc_count; i++)
{
if ((i + bp->uc_count) < PI_CMD_ADDR_FILTER_K_SIZE)
{
memcpy(p_addr, &bp->mc_table[i*FDDI_K_ALEN], FDDI_K_ALEN);
p_addr++; /* point to next command entry */
}
}
/* Issue command to update adapter CAM, then return */
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
return(DFX_K_FAILURE);
return(DFX_K_SUCCESS);
}
/*
* ==========================
* = dfx_ctl_update_filters =
* ==========================
*
* Overview:
* Procedure to update adapter filters with desired
* filter settings.
*
* Returns:
* Condition code
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Enables or disables filter using current filter settings.
*
* Return Codes:
* DFX_K_SUCCESS - Request succeeded.
* DFX_K_FAILURE - Request failed.
*
* Assumptions:
* We must always pass up packets destined to the broadcast
* address (FF-FF-FF-FF-FF-FF), so we'll always keep the
* broadcast filter enabled.
*
* Side Effects:
* On-board adapter filters are updated.
*/
static int dfx_ctl_update_filters(DFX_board_t *bp)
{
int i = 0; /* used as index */
/* Fill in command request information */
bp->cmd_req_virt->cmd_type = PI_CMD_K_FILTERS_SET;
/* Initialize Broadcast filter - * ALWAYS ENABLED * */
bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_BROADCAST;
bp->cmd_req_virt->filter_set.item[i++].value = PI_FSTATE_K_PASS;
/* Initialize LLC Individual/Group Promiscuous filter */
bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_IND_GROUP_PROM;
bp->cmd_req_virt->filter_set.item[i++].value = bp->ind_group_prom;
/* Initialize LLC Group Promiscuous filter */
bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_GROUP_PROM;
bp->cmd_req_virt->filter_set.item[i++].value = bp->group_prom;
/* Terminate the item code list */
bp->cmd_req_virt->filter_set.item[i].item_code = PI_ITEM_K_EOL;
/* Issue command to update adapter filters, then return */
if (dfx_hw_dma_cmd_req(bp) != DFX_K_SUCCESS)
return(DFX_K_FAILURE);
return(DFX_K_SUCCESS);
}
/*
* ======================
* = dfx_hw_dma_cmd_req =
* ======================
*
* Overview:
* Sends PDQ DMA command to adapter firmware
*
* Returns:
* Condition code
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* The command request and response buffers are posted to the adapter in the manner
* described in the PDQ Port Specification:
*
* 1. Command Response Buffer is posted to adapter.
* 2. Command Request Buffer is posted to adapter.
* 3. Command Request consumer index is polled until it indicates that request
* buffer has been DMA'd to adapter.
* 4. Command Response consumer index is polled until it indicates that response
* buffer has been DMA'd from adapter.
*
* This ordering ensures that a response buffer is already available for the firmware
* to use once it's done processing the request buffer.
*
* Return Codes:
* DFX_K_SUCCESS - DMA command succeeded
* DFX_K_OUTSTATE - Adapter is NOT in proper state
* DFX_K_HW_TIMEOUT - DMA command timed out
*
* Assumptions:
* Command request buffer has already been filled with desired DMA command.
*
* Side Effects:
* None
*/
static int dfx_hw_dma_cmd_req(DFX_board_t *bp)
{
int status; /* adapter status */
int timeout_cnt; /* used in for loops */
/* Make sure the adapter is in a state that we can issue the DMA command in */
status = dfx_hw_adap_state_rd(bp);
if ((status == PI_STATE_K_RESET) ||
(status == PI_STATE_K_HALTED) ||
(status == PI_STATE_K_DMA_UNAVAIL) ||
(status == PI_STATE_K_UPGRADE))
return(DFX_K_OUTSTATE);
/* Put response buffer on the command response queue */
bp->descr_block_virt->cmd_rsp[bp->cmd_rsp_reg.index.prod].long_0 = (u32) (PI_RCV_DESCR_M_SOP |
((PI_CMD_RSP_K_SIZE_MAX / PI_ALIGN_K_CMD_RSP_BUFF) << PI_RCV_DESCR_V_SEG_LEN));
bp->descr_block_virt->cmd_rsp[bp->cmd_rsp_reg.index.prod].long_1 = bp->cmd_rsp_phys;
/* Bump (and wrap) the producer index and write out to register */
bp->cmd_rsp_reg.index.prod += 1;
bp->cmd_rsp_reg.index.prod &= PI_CMD_RSP_K_NUM_ENTRIES-1;
dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_RSP_PROD, bp->cmd_rsp_reg.lword);
/* Put request buffer on the command request queue */
bp->descr_block_virt->cmd_req[bp->cmd_req_reg.index.prod].long_0 = (u32) (PI_XMT_DESCR_M_SOP |
PI_XMT_DESCR_M_EOP | (PI_CMD_REQ_K_SIZE_MAX << PI_XMT_DESCR_V_SEG_LEN));
bp->descr_block_virt->cmd_req[bp->cmd_req_reg.index.prod].long_1 = bp->cmd_req_phys;
/* Bump (and wrap) the producer index and write out to register */
bp->cmd_req_reg.index.prod += 1;
bp->cmd_req_reg.index.prod &= PI_CMD_REQ_K_NUM_ENTRIES-1;
dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_REQ_PROD, bp->cmd_req_reg.lword);
/*
* Here we wait for the command request consumer index to be equal
* to the producer, indicating that the adapter has DMAed the request.
*/
for (timeout_cnt = 20000; timeout_cnt > 0; timeout_cnt--)
{
if (bp->cmd_req_reg.index.prod == (u8)(bp->cons_block_virt->cmd_req))
break;
udelay(100); /* wait for 100 microseconds */
}
if (timeout_cnt == 0)
return(DFX_K_HW_TIMEOUT);
/* Bump (and wrap) the completion index and write out to register */
bp->cmd_req_reg.index.comp += 1;
bp->cmd_req_reg.index.comp &= PI_CMD_REQ_K_NUM_ENTRIES-1;
dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_REQ_PROD, bp->cmd_req_reg.lword);
/*
* Here we wait for the command response consumer index to be equal
* to the producer, indicating that the adapter has DMAed the response.
*/
for (timeout_cnt = 20000; timeout_cnt > 0; timeout_cnt--)
{
if (bp->cmd_rsp_reg.index.prod == (u8)(bp->cons_block_virt->cmd_rsp))
break;
udelay(100); /* wait for 100 microseconds */
}
if (timeout_cnt == 0)
return(DFX_K_HW_TIMEOUT);
/* Bump (and wrap) the completion index and write out to register */
bp->cmd_rsp_reg.index.comp += 1;
bp->cmd_rsp_reg.index.comp &= PI_CMD_RSP_K_NUM_ENTRIES-1;
dfx_port_write_long(bp, PI_PDQ_K_REG_CMD_RSP_PROD, bp->cmd_rsp_reg.lword);
return(DFX_K_SUCCESS);
}
/*
* ========================
* = dfx_hw_port_ctrl_req =
* ========================
*
* Overview:
* Sends PDQ port control command to adapter firmware
*
* Returns:
* Host data register value in host_data if ptr is not NULL
*
* Arguments:
* bp - pointer to board information
* command - port control command
* data_a - port data A register value
* data_b - port data B register value
* host_data - ptr to host data register value
*
* Functional Description:
* Send generic port control command to adapter by writing
* to various PDQ port registers, then polling for completion.
*
* Return Codes:
* DFX_K_SUCCESS - port control command succeeded
* DFX_K_HW_TIMEOUT - port control command timed out
*
* Assumptions:
* None
*
* Side Effects:
* None
*/
static int dfx_hw_port_ctrl_req(
DFX_board_t *bp,
PI_UINT32 command,
PI_UINT32 data_a,
PI_UINT32 data_b,
PI_UINT32 *host_data
)
{
PI_UINT32 port_cmd; /* Port Control command register value */
int timeout_cnt; /* used in for loops */
/* Set Command Error bit in command longword */
port_cmd = (PI_UINT32) (command | PI_PCTRL_M_CMD_ERROR);
/* Issue port command to the adapter */
dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_A, data_a);
dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_B, data_b);
dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_CTRL, port_cmd);
/* Now wait for command to complete */
if (command == PI_PCTRL_M_BLAST_FLASH)
timeout_cnt = 600000; /* set command timeout count to 60 seconds */
else
timeout_cnt = 20000; /* set command timeout count to 2 seconds */
for (; timeout_cnt > 0; timeout_cnt--)
{
dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_CTRL, &port_cmd);
if (!(port_cmd & PI_PCTRL_M_CMD_ERROR))
break;
udelay(100); /* wait for 100 microseconds */
}
if (timeout_cnt == 0)
return(DFX_K_HW_TIMEOUT);
/*
* If the address of host_data is non-zero, assume caller has supplied a
* non NULL pointer, and return the contents of the HOST_DATA register in
* it.
*/
if (host_data != NULL)
dfx_port_read_long(bp, PI_PDQ_K_REG_HOST_DATA, host_data);
return(DFX_K_SUCCESS);
}
/*
* =====================
* = dfx_hw_adap_reset =
* =====================
*
* Overview:
* Resets adapter
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
* type - type of reset to perform
*
* Functional Description:
* Issue soft reset to adapter by writing to PDQ Port Reset
* register. Use incoming reset type to tell adapter what
* kind of reset operation to perform.
*
* Return Codes:
* None
*
* Assumptions:
* This routine merely issues a soft reset to the adapter.
* It is expected that after this routine returns, the caller
* will appropriately poll the Port Status register for the
* adapter to enter the proper state.
*
* Side Effects:
* Internal adapter registers are cleared.
*/
static void dfx_hw_adap_reset(
DFX_board_t *bp,
PI_UINT32 type
)
{
/* Set Reset type and assert reset */
dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_DATA_A, type); /* tell adapter type of reset */
dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_RESET, PI_RESET_M_ASSERT_RESET);
/* Wait for at least 1 Microsecond according to the spec. We wait 20 just to be safe */
udelay(20);
/* Deassert reset */
dfx_port_write_long(bp, PI_PDQ_K_REG_PORT_RESET, 0);
}
/*
* ========================
* = dfx_hw_adap_state_rd =
* ========================
*
* Overview:
* Returns current adapter state
*
* Returns:
* Adapter state per PDQ Port Specification
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Reads PDQ Port Status register and returns adapter state.
*
* Return Codes:
* None
*
* Assumptions:
* None
*
* Side Effects:
* None
*/
static int dfx_hw_adap_state_rd(DFX_board_t *bp)
{
PI_UINT32 port_status; /* Port Status register value */
dfx_port_read_long(bp, PI_PDQ_K_REG_PORT_STATUS, &port_status);
return((port_status & PI_PSTATUS_M_STATE) >> PI_PSTATUS_V_STATE);
}
/*
* =====================
* = dfx_hw_dma_uninit =
* =====================
*
* Overview:
* Brings adapter to DMA_UNAVAILABLE state
*
* Returns:
* Condition code
*
* Arguments:
* bp - pointer to board information
* type - type of reset to perform
*
* Functional Description:
* Bring adapter to DMA_UNAVAILABLE state by performing the following:
* 1. Set reset type bit in Port Data A Register then reset adapter.
* 2. Check that adapter is in DMA_UNAVAILABLE state.
*
* Return Codes:
* DFX_K_SUCCESS - adapter is in DMA_UNAVAILABLE state
* DFX_K_HW_TIMEOUT - adapter did not reset properly
*
* Assumptions:
* None
*
* Side Effects:
* Internal adapter registers are cleared.
*/
static int dfx_hw_dma_uninit(DFX_board_t *bp, PI_UINT32 type)
{
int timeout_cnt; /* used in for loops */
/* Set reset type bit and reset adapter */
dfx_hw_adap_reset(bp, type);
/* Now wait for adapter to enter DMA_UNAVAILABLE state */
for (timeout_cnt = 100000; timeout_cnt > 0; timeout_cnt--)
{
if (dfx_hw_adap_state_rd(bp) == PI_STATE_K_DMA_UNAVAIL)
break;
udelay(100); /* wait for 100 microseconds */
}
if (timeout_cnt == 0)
return(DFX_K_HW_TIMEOUT);
return(DFX_K_SUCCESS);
}
/*
* Align an sk_buff to a boundary power of 2
*
*/
static void my_skb_align(struct sk_buff *skb, int n)
{
unsigned long x = (unsigned long)skb->data;
unsigned long v;
v = ALIGN(x, n); /* Where we want to be */
skb_reserve(skb, v - x);
}
/*
* ================
* = dfx_rcv_init =
* ================
*
* Overview:
* Produces buffers to adapter LLC Host receive descriptor block
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
* get_buffers - non-zero if buffers to be allocated
*
* Functional Description:
* This routine can be called during dfx_adap_init() or during an adapter
* reset. It initializes the descriptor block and produces all allocated
* LLC Host queue receive buffers.
*
* Return Codes:
* Return 0 on success or -ENOMEM if buffer allocation failed (when using
* dynamic buffer allocation). If the buffer allocation failed, the
* already allocated buffers will not be released and the caller should do
* this.
*
* Assumptions:
* The PDQ has been reset and the adapter and driver maintained Type 2
* register indices are cleared.
*
* Side Effects:
* Receive buffers are posted to the adapter LLC queue and the adapter
* is notified.
*/
static int dfx_rcv_init(DFX_board_t *bp, int get_buffers)
{
int i, j; /* used in for loop */
/*
* Since each receive buffer is a single fragment of same length, initialize
* first longword in each receive descriptor for entire LLC Host descriptor
* block. Also initialize second longword in each receive descriptor with
* physical address of receive buffer. We'll always allocate receive
* buffers in powers of 2 so that we can easily fill the 256 entry descriptor
* block and produce new receive buffers by simply updating the receive
* producer index.
*
* Assumptions:
* To support all shipping versions of PDQ, the receive buffer size
* must be mod 128 in length and the physical address must be 128 byte
* aligned. In other words, bits 0-6 of the length and address must
* be zero for the following descriptor field entries to be correct on
* all PDQ-based boards. We guaranteed both requirements during
* driver initialization when we allocated memory for the receive buffers.
*/
if (get_buffers) {
#ifdef DYNAMIC_BUFFERS
for (i = 0; i < (int)(bp->rcv_bufs_to_post); i++)
for (j = 0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post)
{
struct sk_buff *newskb = __dev_alloc_skb(NEW_SKB_SIZE, GFP_NOIO);
if (!newskb)
return -ENOMEM;
bp->descr_block_virt->rcv_data[i+j].long_0 = (u32) (PI_RCV_DESCR_M_SOP |
((PI_RCV_DATA_K_SIZE_MAX / PI_ALIGN_K_RCV_DATA_BUFF) << PI_RCV_DESCR_V_SEG_LEN));
/*
* align to 128 bytes for compatibility with
* the old EISA boards.
*/
my_skb_align(newskb, 128);
bp->descr_block_virt->rcv_data[i + j].long_1 =
(u32)dma_map_single(bp->bus_dev, newskb->data,
NEW_SKB_SIZE,
DMA_FROM_DEVICE);
/*
* p_rcv_buff_va is only used inside the
* kernel so we put the skb pointer here.
*/
bp->p_rcv_buff_va[i+j] = (char *) newskb;
}
#else
for (i=0; i < (int)(bp->rcv_bufs_to_post); i++)
for (j=0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post)
{
bp->descr_block_virt->rcv_data[i+j].long_0 = (u32) (PI_RCV_DESCR_M_SOP |
((PI_RCV_DATA_K_SIZE_MAX / PI_ALIGN_K_RCV_DATA_BUFF) << PI_RCV_DESCR_V_SEG_LEN));
bp->descr_block_virt->rcv_data[i+j].long_1 = (u32) (bp->rcv_block_phys + (i * PI_RCV_DATA_K_SIZE_MAX));
bp->p_rcv_buff_va[i+j] = (char *) (bp->rcv_block_virt + (i * PI_RCV_DATA_K_SIZE_MAX));
}
#endif
}
/* Update receive producer and Type 2 register */
bp->rcv_xmt_reg.index.rcv_prod = bp->rcv_bufs_to_post;
dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword);
return 0;
}
/*
* =========================
* = dfx_rcv_queue_process =
* =========================
*
* Overview:
* Process received LLC frames.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Received LLC frames are processed until there are no more consumed frames.
* Once all frames are processed, the receive buffers are returned to the
* adapter. Note that this algorithm fixes the length of time that can be spent
* in this routine, because there are a fixed number of receive buffers to
* process and buffers are not produced until this routine exits and returns
* to the ISR.
*
* Return Codes:
* None
*
* Assumptions:
* None
*
* Side Effects:
* None
*/
static void dfx_rcv_queue_process(
DFX_board_t *bp
)
{
PI_TYPE_2_CONSUMER *p_type_2_cons; /* ptr to rcv/xmt consumer block register */
char *p_buff; /* ptr to start of packet receive buffer (FMC descriptor) */
u32 descr, pkt_len; /* FMC descriptor field and packet length */
struct sk_buff *skb; /* pointer to a sk_buff to hold incoming packet data */
/* Service all consumed LLC receive frames */
p_type_2_cons = (PI_TYPE_2_CONSUMER *)(&bp->cons_block_virt->xmt_rcv_data);
while (bp->rcv_xmt_reg.index.rcv_comp != p_type_2_cons->index.rcv_cons)
{
/* Process any errors */
int entry;
entry = bp->rcv_xmt_reg.index.rcv_comp;
#ifdef DYNAMIC_BUFFERS
p_buff = (char *) (((struct sk_buff *)bp->p_rcv_buff_va[entry])->data);
#else
p_buff = (char *) bp->p_rcv_buff_va[entry];
#endif
memcpy(&descr, p_buff + RCV_BUFF_K_DESCR, sizeof(u32));
if (descr & PI_FMC_DESCR_M_RCC_FLUSH)
{
if (descr & PI_FMC_DESCR_M_RCC_CRC)
bp->rcv_crc_errors++;
else
bp->rcv_frame_status_errors++;
}
else
{
int rx_in_place = 0;
/* The frame was received without errors - verify packet length */
pkt_len = (u32)((descr & PI_FMC_DESCR_M_LEN) >> PI_FMC_DESCR_V_LEN);
pkt_len -= 4; /* subtract 4 byte CRC */
if (!IN_RANGE(pkt_len, FDDI_K_LLC_ZLEN, FDDI_K_LLC_LEN))
bp->rcv_length_errors++;
else{
#ifdef DYNAMIC_BUFFERS
if (pkt_len > SKBUFF_RX_COPYBREAK) {
struct sk_buff *newskb;
newskb = dev_alloc_skb(NEW_SKB_SIZE);
if (newskb){
rx_in_place = 1;
my_skb_align(newskb, 128);
skb = (struct sk_buff *)bp->p_rcv_buff_va[entry];
dma_unmap_single(bp->bus_dev,
bp->descr_block_virt->rcv_data[entry].long_1,
NEW_SKB_SIZE,
DMA_FROM_DEVICE);
skb_reserve(skb, RCV_BUFF_K_PADDING);
bp->p_rcv_buff_va[entry] = (char *)newskb;
bp->descr_block_virt->rcv_data[entry].long_1 =
(u32)dma_map_single(bp->bus_dev,
newskb->data,
NEW_SKB_SIZE,
DMA_FROM_DEVICE);
} else
skb = NULL;
} else
#endif
skb = dev_alloc_skb(pkt_len+3); /* alloc new buffer to pass up, add room for PRH */
if (skb == NULL)
{
printk("%s: Could not allocate receive buffer. Dropping packet.\n", bp->dev->name);
bp->rcv_discards++;
break;
}
else {
#ifndef DYNAMIC_BUFFERS
if (! rx_in_place)
#endif
{
/* Receive buffer allocated, pass receive packet up */
skb_copy_to_linear_data(skb,
p_buff + RCV_BUFF_K_PADDING,
pkt_len + 3);
}
skb_reserve(skb,3); /* adjust data field so that it points to FC byte */
skb_put(skb, pkt_len); /* pass up packet length, NOT including CRC */
skb->protocol = fddi_type_trans(skb, bp->dev);
bp->rcv_total_bytes += skb->len;
netif_rx(skb);
/* Update the rcv counters */
bp->rcv_total_frames++;
if (*(p_buff + RCV_BUFF_K_DA) & 0x01)
bp->rcv_multicast_frames++;
}
}
}
/*
* Advance the producer (for recycling) and advance the completion
* (for servicing received frames). Note that it is okay to
* advance the producer without checking that it passes the
* completion index because they are both advanced at the same
* rate.
*/
bp->rcv_xmt_reg.index.rcv_prod += 1;
bp->rcv_xmt_reg.index.rcv_comp += 1;
}
}
/*
* =====================
* = dfx_xmt_queue_pkt =
* =====================
*
* Overview:
* Queues packets for transmission
*
* Returns:
* Condition code
*
* Arguments:
* skb - pointer to sk_buff to queue for transmission
* dev - pointer to device information
*
* Functional Description:
* Here we assume that an incoming skb transmit request
* is contained in a single physically contiguous buffer
* in which the virtual address of the start of packet
* (skb->data) can be converted to a physical address
* by using pci_map_single().
*
* Since the adapter architecture requires a three byte
* packet request header to prepend the start of packet,
* we'll write the three byte field immediately prior to
* the FC byte. This assumption is valid because we've
* ensured that dev->hard_header_len includes three pad
* bytes. By posting a single fragment to the adapter,
* we'll reduce the number of descriptor fetches and
* bus traffic needed to send the request.
*
* Also, we can't free the skb until after it's been DMA'd
* out by the adapter, so we'll queue it in the driver and
* return it in dfx_xmt_done.
*
* Return Codes:
* 0 - driver queued packet, link is unavailable, or skbuff was bad
* 1 - caller should requeue the sk_buff for later transmission
*
* Assumptions:
* First and foremost, we assume the incoming skb pointer
* is NOT NULL and is pointing to a valid sk_buff structure.
*
* The outgoing packet is complete, starting with the
* frame control byte including the last byte of data,
* but NOT including the 4 byte CRC. We'll let the
* adapter hardware generate and append the CRC.
*
* The entire packet is stored in one physically
* contiguous buffer which is not cached and whose
* 32-bit physical address can be determined.
*
* It's vital that this routine is NOT reentered for the
* same board and that the OS is not in another section of
* code (eg. dfx_int_common) for the same board on a
* different thread.
*
* Side Effects:
* None
*/
static int dfx_xmt_queue_pkt(
struct sk_buff *skb,
struct net_device *dev
)
{
DFX_board_t *bp = netdev_priv(dev);
u8 prod; /* local transmit producer index */
PI_XMT_DESCR *p_xmt_descr; /* ptr to transmit descriptor block entry */
XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */
unsigned long flags;
netif_stop_queue(dev);
/*
* Verify that incoming transmit request is OK
*
* Note: The packet size check is consistent with other
* Linux device drivers, although the correct packet
* size should be verified before calling the
* transmit routine.
*/
if (!IN_RANGE(skb->len, FDDI_K_LLC_ZLEN, FDDI_K_LLC_LEN))
{
printk("%s: Invalid packet length - %u bytes\n",
dev->name, skb->len);
bp->xmt_length_errors++; /* bump error counter */
netif_wake_queue(dev);
dev_kfree_skb(skb);
return(0); /* return "success" */
}
/*
* See if adapter link is available, if not, free buffer
*
* Note: If the link isn't available, free buffer and return 0
* rather than tell the upper layer to requeue the packet.
* The methodology here is that by the time the link
* becomes available, the packet to be sent will be
* fairly stale. By simply dropping the packet, the
* higher layer protocols will eventually time out
* waiting for response packets which it won't receive.
*/
if (bp->link_available == PI_K_FALSE)
{
if (dfx_hw_adap_state_rd(bp) == PI_STATE_K_LINK_AVAIL) /* is link really available? */
bp->link_available = PI_K_TRUE; /* if so, set flag and continue */
else
{
bp->xmt_discards++; /* bump error counter */
dev_kfree_skb(skb); /* free sk_buff now */
netif_wake_queue(dev);
return(0); /* return "success" */
}
}
spin_lock_irqsave(&bp->lock, flags);
/* Get the current producer and the next free xmt data descriptor */
prod = bp->rcv_xmt_reg.index.xmt_prod;
p_xmt_descr = &(bp->descr_block_virt->xmt_data[prod]);
/*
* Get pointer to auxiliary queue entry to contain information
* for this packet.
*
* Note: The current xmt producer index will become the
* current xmt completion index when we complete this
* packet later on. So, we'll get the pointer to the
* next auxiliary queue entry now before we bump the
* producer index.
*/
p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[prod++]); /* also bump producer index */
/* Write the three PRH bytes immediately before the FC byte */
skb_push(skb,3);
skb->data[0] = DFX_PRH0_BYTE; /* these byte values are defined */
skb->data[1] = DFX_PRH1_BYTE; /* in the Motorola FDDI MAC chip */
skb->data[2] = DFX_PRH2_BYTE; /* specification */
/*
* Write the descriptor with buffer info and bump producer
*
* Note: Since we need to start DMA from the packet request
* header, we'll add 3 bytes to the DMA buffer length,
* and we'll determine the physical address of the
* buffer from the PRH, not skb->data.
*
* Assumptions:
* 1. Packet starts with the frame control (FC) byte
* at skb->data.
* 2. The 4-byte CRC is not appended to the buffer or
* included in the length.
* 3. Packet length (skb->len) is from FC to end of
* data, inclusive.
* 4. The packet length does not exceed the maximum
* FDDI LLC frame length of 4491 bytes.
* 5. The entire packet is contained in a physically
* contiguous, non-cached, locked memory space
* comprised of a single buffer pointed to by
* skb->data.
* 6. The physical address of the start of packet
* can be determined from the virtual address
* by using pci_map_single() and is only 32-bits
* wide.
*/
p_xmt_descr->long_0 = (u32) (PI_XMT_DESCR_M_SOP | PI_XMT_DESCR_M_EOP | ((skb->len) << PI_XMT_DESCR_V_SEG_LEN));
p_xmt_descr->long_1 = (u32)dma_map_single(bp->bus_dev, skb->data,
skb->len, DMA_TO_DEVICE);
/*
* Verify that descriptor is actually available
*
* Note: If descriptor isn't available, return 1 which tells
* the upper layer to requeue the packet for later
* transmission.
*
* We need to ensure that the producer never reaches the
* completion, except to indicate that the queue is empty.
*/
if (prod == bp->rcv_xmt_reg.index.xmt_comp)
{
skb_pull(skb,3);
spin_unlock_irqrestore(&bp->lock, flags);
return(1); /* requeue packet for later */
}
/*
* Save info for this packet for xmt done indication routine
*
* Normally, we'd save the producer index in the p_xmt_drv_descr
* structure so that we'd have it handy when we complete this
* packet later (in dfx_xmt_done). However, since the current
* transmit architecture guarantees a single fragment for the
* entire packet, we can simply bump the completion index by
* one (1) for each completed packet.
*
* Note: If this assumption changes and we're presented with
* an inconsistent number of transmit fragments for packet
* data, we'll need to modify this code to save the current
* transmit producer index.
*/
p_xmt_drv_descr->p_skb = skb;
/* Update Type 2 register */
bp->rcv_xmt_reg.index.xmt_prod = prod;
dfx_port_write_long(bp, PI_PDQ_K_REG_TYPE_2_PROD, bp->rcv_xmt_reg.lword);
spin_unlock_irqrestore(&bp->lock, flags);
netif_wake_queue(dev);
return(0); /* packet queued to adapter */
}
/*
* ================
* = dfx_xmt_done =
* ================
*
* Overview:
* Processes all frames that have been transmitted.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* For all consumed transmit descriptors that have not
* yet been completed, we'll free the skb we were holding
* onto using dev_kfree_skb and bump the appropriate
* counters.
*
* Return Codes:
* None
*
* Assumptions:
* The Type 2 register is not updated in this routine. It is
* assumed that it will be updated in the ISR when dfx_xmt_done
* returns.
*
* Side Effects:
* None
*/
static int dfx_xmt_done(DFX_board_t *bp)
{
XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */
PI_TYPE_2_CONSUMER *p_type_2_cons; /* ptr to rcv/xmt consumer block register */
u8 comp; /* local transmit completion index */
int freed = 0; /* buffers freed */
/* Service all consumed transmit frames */
p_type_2_cons = (PI_TYPE_2_CONSUMER *)(&bp->cons_block_virt->xmt_rcv_data);
while (bp->rcv_xmt_reg.index.xmt_comp != p_type_2_cons->index.xmt_cons)
{
/* Get pointer to the transmit driver descriptor block information */
p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[bp->rcv_xmt_reg.index.xmt_comp]);
/* Increment transmit counters */
bp->xmt_total_frames++;
bp->xmt_total_bytes += p_xmt_drv_descr->p_skb->len;
/* Return skb to operating system */
comp = bp->rcv_xmt_reg.index.xmt_comp;
dma_unmap_single(bp->bus_dev,
bp->descr_block_virt->xmt_data[comp].long_1,
p_xmt_drv_descr->p_skb->len,
DMA_TO_DEVICE);
dev_kfree_skb_irq(p_xmt_drv_descr->p_skb);
/*
* Move to start of next packet by updating completion index
*
* Here we assume that a transmit packet request is always
* serviced by posting one fragment. We can therefore
* simplify the completion code by incrementing the
* completion index by one. This code will need to be
* modified if this assumption changes. See comments
* in dfx_xmt_queue_pkt for more details.
*/
bp->rcv_xmt_reg.index.xmt_comp += 1;
freed++;
}
return freed;
}
/*
* =================
* = dfx_rcv_flush =
* =================
*
* Overview:
* Remove all skb's in the receive ring.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* Free's all the dynamically allocated skb's that are
* currently attached to the device receive ring. This
* function is typically only used when the device is
* initialized or reinitialized.
*
* Return Codes:
* None
*
* Side Effects:
* None
*/
#ifdef DYNAMIC_BUFFERS
static void dfx_rcv_flush( DFX_board_t *bp )
{
int i, j;
for (i = 0; i < (int)(bp->rcv_bufs_to_post); i++)
for (j = 0; (i + j) < (int)PI_RCV_DATA_K_NUM_ENTRIES; j += bp->rcv_bufs_to_post)
{
struct sk_buff *skb;
skb = (struct sk_buff *)bp->p_rcv_buff_va[i+j];
if (skb)
dev_kfree_skb(skb);
bp->p_rcv_buff_va[i+j] = NULL;
}
}
#else
static inline void dfx_rcv_flush( DFX_board_t *bp )
{
}
#endif /* DYNAMIC_BUFFERS */
/*
* =================
* = dfx_xmt_flush =
* =================
*
* Overview:
* Processes all frames whether they've been transmitted
* or not.
*
* Returns:
* None
*
* Arguments:
* bp - pointer to board information
*
* Functional Description:
* For all produced transmit descriptors that have not
* yet been completed, we'll free the skb we were holding
* onto using dev_kfree_skb and bump the appropriate
* counters. Of course, it's possible that some of
* these transmit requests actually did go out, but we
* won't make that distinction here. Finally, we'll
* update the consumer index to match the producer.
*
* Return Codes:
* None
*
* Assumptions:
* This routine does NOT update the Type 2 register. It
* is assumed that this routine is being called during a
* transmit flush interrupt, or a shutdown or close routine.
*
* Side Effects:
* None
*/
static void dfx_xmt_flush( DFX_board_t *bp )
{
u32 prod_cons; /* rcv/xmt consumer block longword */
XMT_DRIVER_DESCR *p_xmt_drv_descr; /* ptr to transmit driver descriptor */
u8 comp; /* local transmit completion index */
/* Flush all outstanding transmit frames */
while (bp->rcv_xmt_reg.index.xmt_comp != bp->rcv_xmt_reg.index.xmt_prod)
{
/* Get pointer to the transmit driver descriptor block information */
p_xmt_drv_descr = &(bp->xmt_drv_descr_blk[bp->rcv_xmt_reg.index.xmt_comp]);
/* Return skb to operating system */
comp = bp->rcv_xmt_reg.index.xmt_comp;
dma_unmap_single(bp->bus_dev,
bp->descr_block_virt->xmt_data[comp].long_1,
p_xmt_drv_descr->p_skb->len,
DMA_TO_DEVICE);
dev_kfree_skb(p_xmt_drv_descr->p_skb);
/* Increment transmit error counter */
bp->xmt_discards++;
/*
* Move to start of next packet by updating completion index
*
* Here we assume that a transmit packet request is always
* serviced by posting one fragment. We can therefore
* simplify the completion code by incrementing the
* completion index by one. This code will need to be
* modified if this assumption changes. See comments
* in dfx_xmt_queue_pkt for more details.
*/
bp->rcv_xmt_reg.index.xmt_comp += 1;
}
/* Update the transmit consumer index in the consumer block */
prod_cons = (u32)(bp->cons_block_virt->xmt_rcv_data & ~PI_CONS_M_XMT_INDEX);
prod_cons |= (u32)(bp->rcv_xmt_reg.index.xmt_prod << PI_CONS_V_XMT_INDEX);
bp->cons_block_virt->xmt_rcv_data = prod_cons;
}
/*
* ==================
* = dfx_unregister =
* ==================
*
* Overview:
* Shuts down an FDDI controller
*
* Returns:
* Condition code
*
* Arguments:
* bdev - pointer to device information
*
* Functional Description:
*
* Return Codes:
* None
*
* Assumptions:
* It compiles so it should work :-( (PCI cards do :-)
*
* Side Effects:
* Device structures for FDDI adapters (fddi0, fddi1, etc) are
* freed.
*/
static void __devexit dfx_unregister(struct device *bdev)
{
struct net_device *dev = dev_get_drvdata(bdev);
DFX_board_t *bp = netdev_priv(dev);
int dfx_bus_pci = DFX_BUS_PCI(bdev);
int dfx_bus_tc = DFX_BUS_TC(bdev);
int dfx_use_mmio = DFX_MMIO || dfx_bus_tc;
resource_size_t bar_start = 0; /* pointer to port */
resource_size_t bar_len = 0; /* resource length */
int alloc_size; /* total buffer size used */
unregister_netdev(dev);
alloc_size = sizeof(PI_DESCR_BLOCK) +
PI_CMD_REQ_K_SIZE_MAX + PI_CMD_RSP_K_SIZE_MAX +
#ifndef DYNAMIC_BUFFERS
(bp->rcv_bufs_to_post * PI_RCV_DATA_K_SIZE_MAX) +
#endif
sizeof(PI_CONSUMER_BLOCK) +
(PI_ALIGN_K_DESC_BLK - 1);
if (bp->kmalloced)
dma_free_coherent(bdev, alloc_size,
bp->kmalloced, bp->kmalloced_dma);
dfx_bus_uninit(dev);
dfx_get_bars(bdev, &bar_start, &bar_len);
if (dfx_use_mmio) {
iounmap(bp->base.mem);
release_mem_region(bar_start, bar_len);
} else
release_region(bar_start, bar_len);
if (dfx_bus_pci)
pci_disable_device(to_pci_dev(bdev));
free_netdev(dev);
}
static int __devinit __maybe_unused dfx_dev_register(struct device *);
static int __devexit __maybe_unused dfx_dev_unregister(struct device *);
#ifdef CONFIG_PCI
static int __devinit dfx_pci_register(struct pci_dev *,
const struct pci_device_id *);
static void __devexit dfx_pci_unregister(struct pci_dev *);
static struct pci_device_id dfx_pci_table[] = {
{ PCI_DEVICE(PCI_VENDOR_ID_DEC, PCI_DEVICE_ID_DEC_FDDI) },
{ }
};
MODULE_DEVICE_TABLE(pci, dfx_pci_table);
static struct pci_driver dfx_pci_driver = {
.name = "defxx",
.id_table = dfx_pci_table,
.probe = dfx_pci_register,
.remove = __devexit_p(dfx_pci_unregister),
};
static __devinit int dfx_pci_register(struct pci_dev *pdev,
const struct pci_device_id *ent)
{
return dfx_register(&pdev->dev);
}
static void __devexit dfx_pci_unregister(struct pci_dev *pdev)
{
dfx_unregister(&pdev->dev);
}
#endif /* CONFIG_PCI */
#ifdef CONFIG_EISA
static struct eisa_device_id dfx_eisa_table[] = {
{ "DEC3001", DEFEA_PROD_ID_1 },
{ "DEC3002", DEFEA_PROD_ID_2 },
{ "DEC3003", DEFEA_PROD_ID_3 },
{ "DEC3004", DEFEA_PROD_ID_4 },
{ }
};
MODULE_DEVICE_TABLE(eisa, dfx_eisa_table);
static struct eisa_driver dfx_eisa_driver = {
.id_table = dfx_eisa_table,
.driver = {
.name = "defxx",
.bus = &eisa_bus_type,
.probe = dfx_dev_register,
.remove = __devexit_p(dfx_dev_unregister),
},
};
#endif /* CONFIG_EISA */
#ifdef CONFIG_TC
static struct tc_device_id const dfx_tc_table[] = {
{ "DEC ", "PMAF-FA " },
{ "DEC ", "PMAF-FD " },
{ "DEC ", "PMAF-FS " },
{ "DEC ", "PMAF-FU " },
{ }
};
MODULE_DEVICE_TABLE(tc, dfx_tc_table);
static struct tc_driver dfx_tc_driver = {
.id_table = dfx_tc_table,
.driver = {
.name = "defxx",
.bus = &tc_bus_type,
.probe = dfx_dev_register,
.remove = __devexit_p(dfx_dev_unregister),
},
};
#endif /* CONFIG_TC */
static int __devinit __maybe_unused dfx_dev_register(struct device *dev)
{
int status;
status = dfx_register(dev);
if (!status)
get_device(dev);
return status;
}
static int __devexit __maybe_unused dfx_dev_unregister(struct device *dev)
{
put_device(dev);
dfx_unregister(dev);
return 0;
}
static int __devinit dfx_init(void)
{
int status;
status = pci_register_driver(&dfx_pci_driver);
if (!status)
status = eisa_driver_register(&dfx_eisa_driver);
if (!status)
status = tc_register_driver(&dfx_tc_driver);
return status;
}
static void __devexit dfx_cleanup(void)
{
tc_unregister_driver(&dfx_tc_driver);
eisa_driver_unregister(&dfx_eisa_driver);
pci_unregister_driver(&dfx_pci_driver);
}
module_init(dfx_init);
module_exit(dfx_cleanup);
MODULE_AUTHOR("Lawrence V. Stefani");
MODULE_DESCRIPTION("DEC FDDIcontroller TC/EISA/PCI (DEFTA/DEFEA/DEFPA) driver "
DRV_VERSION " " DRV_RELDATE);
MODULE_LICENSE("GPL");